Radar Vectors
Proposed Rule Proposed Issued May 9, 2006 4 pages Copy saved Nov 17, 2026

71 FR 26891 Airworthiness Directives; Pilatus Aircraft Ltd. Models PC-6, PC-6-H1, PC-6-H2, PC-6/350, PC-6/350-H1, PC-6/350-H2, PC-6/A, PC-6/A-H1, PC-6/A-H2, PC-6/B-H2, PC-6/B1-H2, PC-6/B2-H2, PC-6/B2-H4, PC-6/C-H2, and PC-6/C1-H2 Airplanes

We propose to supersede Airworthiness Directive (AD) 2003-09-01, which applies to Pilatus Aircraft Ltd (Pilatus) Model PC-6 airplanes, all manufacturer serial numbers (MSN) up to and including 939. AD 2003-09-01 currently requires you to inspect and correct, as necessary, the aileron control bellcrank assemblies at the wing and fuselage locations. Since we issued AD 2003-09-01, the FAA determined the action should also apply to all the models of the PC-6 airplanes listed in the type certification data sheet of Type Certificate (TC) No. 7A15 that are produced in the United States through a licensing agreement between Pilatus and Fairchild Republic Company (also identified as Fairchild Industries, Fairchild Heli Porter, or Fairchild-Hiller Corporation). In addition, the intent of the applicability of AD 2003-09-01 was to all the affected serial numbers of the airplane models listed in TC No. 7A15. Consequently, this proposed AD would retain all the actions of AD 2003-09-01, would add those Fairchild Republic Company airplanes to the applicability of this proposed AD, and would list out the individual specific airplane models. We are proposing this AD to detect and correct increased friction in the aileron control bellcrank assemblies, which could result in failure of the aileron flight-control system. Such failure could lead to problems in controlling flight.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2006-24092; Directorate Identifier 2006-CE-18-AD] RIN 2120-AA64

Airworthiness Directives; Pilatus Aircraft Ltd. Models PC-6, PC-6-H1, PC-6-H2, PC-6/350, PC-6/350-H1, PC-6/350-H2, PC-6/A, PC-6/A-H1, PC-6/A-H2, PC-6/B-H2, PC-6/B1-H2, PC-6/B2-H2, PC-6/B2-H4, PC-6/C-H2, and PC-6/C1-H2 Airplanes

Agency

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2003-09-01, which applies to Pilatus Aircraft Ltd (Pilatus) Model PC-6 airplanes, all manufacturer serial numbers (MSN) up to and including 939. AD 2003-09-01 currently requires you to inspect and correct, as necessary, the aileron control bellcrank assemblies at the wing and fuselage locations. Since we issued AD 2003-09-01, the FAA determined the action should also apply to all the models of the PC-6 airplanes listed in the type certification data sheet of Type Certificate (TC) No. 7A15 that are produced in the United States through a licensing agreement between Pilatus and Fairchild Republic Company (also identified as Fairchild Industries, Fairchild Heli Porter, or Fairchild-Hiller Corporation). In addition, the intent of the applicability of AD 2003-09-01 was to all the affected serial numbers of the airplane models listed in TC No. 7A15. Consequently, this proposed AD would retain all the actions of AD 2003-09-01, would add those Fairchild Republic Company airplanes to the applicability of this proposed AD, and would list out the individual specific airplane models. We are proposing this AD to detect and correct increased friction in the aileron control bellcrank assemblies, which could result in failure of the aileron flight-control system. Such failure could lead to problems in controlling flight.

Dates

DATES: We must receive comments on this proposed AD by June 9, 2006.

ADDRESSES: Use one of the following addresses to comment on this proposed AD:

• DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.

• Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.

Addresses

• Mail: Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-0001.

• Fax: (202) 493-2251.

• Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Pilatus Aircraft Ltd., Customer Liaison Manager, CH-6371 Stans, Switzerland; telephone: +41 41 619 63 19; facsimile: +41 41 619 6224.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4059; facsimile: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number, "FAA-2006-24092; Directorate Identifier 2006-CE-18-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

Comments Invited

We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this proposed AD.

Discussion

Mandatory continuing airworthiness information and the FAA's determination that an unsafe condition existed on a Pilatus Model PC-6 airplane caused us to issue AD 2003-09-01, Amendment 39-13130 (68 FR 22582, April 29, 2003). AD 2003-09-01 currently requires you to inspect and correct, as necessary, the aileron control bellcrank assemblies at the wing and fuselage locations on Pilatus Model PC-6 airplanes.

Discussion

The Federal Office for Civil Aviation (FOCA), which is the airworthiness authority for Switzerland, notified the FAA of the need to supersede AD 2003-09-01 to address an unsafe condition that may exist or could develop on Model PC-6 airplanes, all manufacturer serial numbers (MSN) up to and including 939. The FOCA reports that the AD action should also apply to all the models of the PC-6 airplanes listed in the type certification data sheet of TC No. 7A15 produced in the United States through a licensing agreement between Pilatus and Fairchild Republic Company (also identified as Fairchild Industries, Fairchild Heli Porter, or Fairchild-Hiller Corporation).

This condition, if not corrected, could result in increased friction in the aileron control bellcrank assemblies, which could result in failure of the aileron flight-control system. Such failure could lead to problems in controlling flight.

Foreign Airworthiness Authority Information

Foreign Airworthiness Authority Information

The FOCA recently issued Swiss AD Number HB 2005-289, effective date August 23, 2005, to ensure the continued airworthiness of all models of the PC-6 airplanes listed in TC No. 7A15, including those produced in the United States under a licensing agreement with Pilatus and Fairchild Republic Company (also identified as Fairchild Industries, Fairchild Heli Porter, or Fairchild-Hiller Corporation).

The State of Design for the Pilatus PC-6 airplanes is Switzerland and the airplanes are type-certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement.

Under this bilateral airworthiness agreement, the FOCA has kept us informed of the situation described above.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

We are proposing this AD because we have examined the FOCA's findings, evaluated all information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design that are certificated for operation in the United States.

This proposed AD would supersede AD 2003-09-01 with a new AD that would retain all the actions of AD 2003-09-01 and would:

• Add manufacturer serial numbers (MSN) 2001 through 2092 for all the models of the PC-6 airplanes as listed in TC No. 7A15 and specified in the applicability section. These MSN are the airplanes produced in the United States through a licensing agreement with the Fairchild Republic Company; and

• List all the models of the PC-6 airplanes as listed in TC No. 7A15.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 49 airplanes in the U.S. registry.

We estimate the following costs to do the proposed inspection and modifications:

Total cost

Labor cost Parts cost per airplane Total cost on U.S. operators

7 work hours x $80 per hour = $560 … $300 $860 $860 x 49 = $42,140.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket that contains the proposed AD, the regulatory evaluation, any comments received, and other information on the Internet at http://dms.dot.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5227) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

PART 39--AIRWORTHINESS DIRECTIVES

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2003-09-01, Amendment 39-13130, and adding the following new AD:

Pilatus Aircraft LTD.: Docket No. FAA-2006-24092; Directorate Identifier 2006-CE-18-AD.

Comments Due Date

Comments Due Date

(a) We must receive comments on this airworthiness directive (AD) action by June 9, 2006.

Affected ADs

(b) This AD supersedes AD 2003-09-01, Amendment 39-13130.

Applicability

(c) This AD affects the following Models PC-6, PC-6-H1, PC-6-H2, PC-6/350, PC-6/350-H1, PC-6/350-H2, PC-6/A, PC-6/A-H1, PC-6/A-H2, PC-6/B-H2, PC-6/B1-H2, PC-6/B2-H2, PC-6/B2-H4, PC-6/C-H2, and PC-6/ C1-H2 airplanes that are equipped with turbo-prop engines and are certificated in any category:

Applicability

(1) Group 1 (maintains the actions from AD 2003-09-01): All manufacturer serial numbers (MSN) up to and including 939.

(2) Group 2: MSN 2001 through 2092.

Note: These airplanes are also identified as Fairchild Republic Company PC-6 airplanes, Fairchild Heli Porter PC-6 airplanes, or Fairchild-Hiller Corporation PC-6 airplanes.

Unsafe Condition

Unsafe Condition

(d) This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland that requires retaining the actions of AD 2003-09-01 and adding MSN 2001 through 2092 for all the models of the PC-6 airplanes listed in the type certificate data sheet of Type Certificate (TC) No. 7A15. We are issuing this AD to detect and correct increased friction in the aileron control bellcrank assemblies, which could result in failure of the aileron flight-control system. Such failure could lead to problems in controlling flight.

Compliance

Compliance

(e) To address this problem, you must do the following:

Actions Compliance Procedures

(1) Inspect, before removal (A) For Group 1 Follow Pilatus

of the wing bellcrank Airplanes: Within Aircraft Ltd. PC-6

assemblies, part numbers (P/ the next 100 hours Service Bulletin

N) 6132.0071.51 and time-in-service No. 27-001, dated

6132.0071.52, for installed (TIS) after June June 5, 2002.

circlips, P/N N237: 17, 2003 (the

(i) If circlips are effective date of

installed, do the actions AD 2003-09-01),

required in paragraphs unless already done.

(e)(5) and (e)(6) of this (B) For Group 2

AD. Airplanes: Within

(ii) If circlips are not the next 100 hours

installed, perform all TIS after the

actions required by effective date of

paragraphs (e)(3), (e)(4), this AD, unless

(e)(5), (e)(6), and (e)(7) already done.

of this AD.

(2) Inspect, before removal Before further Follow Pilatus

of the fuselage bellcrank flight after the Aircraft Ltd. PC-6

assembly, P/N 6232.0118.00, inspection required Service Bulletin

assembly, P/N 6232.0118.00, inspection required Service Bulletin

for the circlip installed in paragraph (e)(1) No. 27-001, dated

on the housing to prevent of this AD. June 5, 2002.

axial movement of the bellcrank on its bearing and the flange of the housing to the rear. If the fuselage bellcrank assembly has either no circlip and/ or it is not installed as required, perform the actions in paragraphs (e)(8) and (e)(9) of this AD.

(3) Remove the wing Before further Follow Pilatus

bellcrank assemblies, P/Ns flight after the Aircraft Ltd. PC-6

6132.0071.51 and inspections Service Bulletin

6132.0071.52, and inspect required in No. 27-001, dated

for worn or damaged paragraphs (e)(1) June 5, 2002.

bearings. Replace worn or and (e)(2) of this

damaged bearings. AD, as applicable.

(4) Stake and lock the Before further Follow Pilatus

bearing in the housing of flight after the Aircraft Ltd. PC-6

the wing bellcranks, P/Ns inspections Service Bulletin

6132.0071.51 and required in No. 27-001, dated

6132.0071.52. paragraphs (e)(1) June 5, 2002.

and (e)(2) of this

AD, as applicable.

(5) Inspect the wing Before further Follow Pilatus

bellcranks control-cable flight after the Aircraft Ltd. PC-6

attachment bolts for inspections Service Bulletin

correct type and for signs required in No. 27-001, dated

of rub damage on the heads. paragraphs (e)(1) June 5, 2002.

Replace bolts that are and (e)(2) of this

damaged and/or have a total AD. length (including head) of more than 21.5 mm (0.85 in.)

damaged and/or have a total AD. length (including head) of more than 21.5 mm (0.85 in.)

(6) Inspect the wing Before further Follow Pilatus

bellcranks support plate flight after the Aircraft Ltd. PC-6

for signs of rub damage inspections Service Bulletin

caused by the bolts. If required in No. 27-001, dated

damage is found: paragraphs (e)(1) June 5, 2002.

(i) Obtain a repair scheme and (e)(2) of this

from the manufacturer AD.

through FAA at the address specified in paragraph (f) of this AD. (ii) Incorporate this repair scheme..

(7) Reinstall wing bellcrank Before further Follow Pilatus

assemblies. flight after the Aircraft Ltd. PC-6

inspections Service Bulletin

required in No. 27-001, dated

paragraphs (e)(1) June 5, 2002.

and (e)(2) of this

AD.

(8) Remove the fuselage Before further Follow Pilatus

bellcrank assembly, P/N flight after the Aircraft Ltd. PC-6

6232.0118.00, and inspect inspections Service Bulletin

the housing for wear, required in No. 27-001, dated

damage, and signs of axial paragraphs (e)(1) June 5, 2002.

movement of the bearing in and (e)(2) of this

the housing. Replace worn AD.

or damaged bearings. If any signs of axial movement of a bearing are found: (i) Obtain a repair scheme from the manufacturer through FAA at the address specified in paragraph (f) of this AD. (ii) Incorporate this repair scheme..

(9) Reinstall the fuselage Before further Follow Pilatus

bellcrank assembly. Ensure flight after the Aircraft Ltd. PC-6

that the fuselage bellcrank inspections Service Bulletin

assembly is installed so required in No. 27-001, dated

that the surface of the paragraphs (e)(1), June 5, 2002.

bellcrank with the flange (e)(2) and (e)(8)

of the housing is installed of this AD. to the rear. The effect of this is to lock the bellcrank on the bearing tube and thus prevent movement.

(10) Do not install any (A) For Group 1 Follow Pilatus

bellcrank assemblies, P/Ns Airplanes: As of Aircraft Ltd. PC-6

6132.0071.51, 6132,0071.52, June 17, 2003 (the Service Bulletin

and 6232.0118.00 (or FAA- effective date of No. 27-001, dated

approved equivalent part AD 2003-09-01). June 5, 2002.

numbers), unless the (B) For Group 2

aileron assembly has been Airplanes: As of

inspected, modified, and the effective date

installed. of this AD.

Note 1: Axial movement of serviceable bearings in the housings of the wing bellcranks is permitted provided no wear or damage to the bearing is found.

Note 2: Any signs of axial movement of a bearing in the housing of the fuselage bellcrank assembly requires that you obtain a repair scheme from the manufacturer through FAA at the address specified in paragraph (f) of this AD and incorporate the repair scheme.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Standards Office, ATTN: Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4059; facsimile: (816) 329-4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19.

(g) AMOCs approved for AD 2003-09-01 are approved for this AD.

Related Information

Related Information

(h) To get copies of the documents referenced in this AD, contact Pilatus Aircraft Ltd., Customer Liaison Manager, CH-6371 Stans, Switzerland; telephone: +41 41 619 63 19; facsimile: +41 41 619 6224. To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC, or on the Internet at http://dms.dot.gov. The docket number is Docket No. FAA-2006-24092; Directorate Identifier 2006-CE-18-AD.

Issued in Kansas City, Missouri, on May 3, 2006. Barry R. Ballenger, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.