Radar Vectors
Proposed Rule Proposed Issued Aug 9, 2006 4 pages Copy saved Nov 17, 2026

71 FR 45451 Airworthiness Directives; Air Tractor, Inc. Models AT-502, AT-502A, AT-502B, AT-602, AT-802, and AT-802A Airplanes

We propose to adopt a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-502, AT-502A, AT-502B, AT-602, AT-802, and AT-802A airplanes. This proposed AD would require you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners, any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion. The AD would also require you to replace any damaged parts found as a result of the inspection and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements. This proposed AD results from two reports (one Model AT-602 airplane and one Model AT-802A airplane) of in-flight rudder separation from the vertical fin at the upper attach hinge area, and other reports of Models AT-502B, AT-602, and AT-802/802A airplanes with loose hinges, skin cracks, or signs of repairs to the affected area. We are proposing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control of the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2006-25260; Directorate Identifier 2006-CE-37-AD] RIN 2120-AA64

Airworthiness Directives; Air Tractor, Inc. Models AT-502, AT-502A, AT-502B, AT-602, AT-802, and AT-802A Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

Action

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-502, AT-502A, AT-502B, AT-602, AT-802, and AT-802A airplanes. This proposed AD would require you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners, any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion. The AD would also require you to replace any damaged parts found as a result of the inspection and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements. This proposed AD results from two reports (one Model AT-602 airplane and one Model AT-802A airplane) of in-flight rudder separation from the vertical fin at the upper attach hinge area, and other reports of Models AT-502B, AT-602, and AT-802/802A airplanes with loose hinges, skin cracks, or signs of repairs to the affected area. We are proposing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control of the airplane.

Dates

DATES: We must receive comments on this proposed AD by October 10, 2006.

ADDRESSES: Use one of the following addresses to comment on this proposed AD:

• DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.

• Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.

Addresses

• Mail: Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-0001.

• Fax: (202) 493-2251.

• Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Air Tractor, Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564-5616; facsimile: (940) 564-5612.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number, "FAA-2006-25260; Directorate Identifier 2006-CE-37-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

Comments Invited

We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this proposed AD.

Discussion

We have received two reports (one Air Tractor Model AT-602 airplane and one Model AT-802A airplane) of in-flight rudder separation at the upper attach hinge area and other reports of Models AT-502B, AT-602, and AT-802/802A airplanes with loose hinges, skin cracks, or signs of repairs to the affected area.

Discussion

Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control of the airplane.

Relevant Service Information

Relevant Service Information

We have reviewed Snow Engineering Co. Service Letter 247, dated August 14, 2005, revised May 17, 2006, and Snow Engineering Co. Process Specification Number 145, dated December 6, 1991. The service information describes procedures for:

• Inspecting (visually) the rudder and fin hinge attaching structure for loose fasteners, any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion;

• Replacing any damaged parts found as a result of the inspection;

• Installing an external doubler at the upper rudder hinge; and

• Balancing of the rudder.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

We are proposing this AD because we evaluated all information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This proposed AD would require you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners, any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion. This AD would also require you to replace any damaged parts found as a result of the inspection and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 945 airplanes in the U.S. registry.

We estimate the following costs to do the proposed inspection:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

1 work-hour x $80 per hour = $80 … Not Applicable … $80 $75,600

We have no way of determining the number of airplanes that may need any replacements that would be required based on the results of the proposed inspection.

We estimate the following costs to do the installation of the external doubler at the upper rudder hinge:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

5 work-hours x $80 per hour = $400 … $217 … $617 $583,065

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket that contains the proposed AD, the regulatory evaluation, any comments received, and other information on the Internet at http://dms.dot.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5227) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority : 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

§ 39.13 [Amended]

2. The FAA amends § 39.13 by adding the following new AD:

Air Tractor, Inc.: Docket No. FAA-2006-25260; Directorate Identifier 2006-CE-37-AD.

Comments Due Date

(a) We must receive comments on this airworthiness directive (AD) action by October 10, 2006.

Affected ADs

Affected ADs

(b) None.

Applicability

(c) This AD affects the following airplane models and serial numbers that are certificated in any category:

Model Serial Nos.

(1) AT-502 and AT-502B … 502/502B-0003 through 502/502B-

2600.

(2) AT-502A … 502A-0003 through 502A-2582.

(3) AT-602 … 602-0337 through 602-1138.

(4) AT-802 and AT-802A … 802/802A-0001 through 802/802A-

Applicability

0215.

Unsafe Condition

(d) This AD results from two reports (one Model AT-602 airplane and one Model AT-802A airplane) of in-flight rudder separations at the upper attach hinge area and other reports of Models AT-502B, AT-602, and AT-802/802A airplanes with loose hinges, skin cracks, or signs of repairs to the affected area. We are issuing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges or brackets, or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control of the airplane.

Compliance

Compliance

(e) To address this problem, you must do the following:

Actions Compliance Procedures

(1) Inspect visually the rudder Initially inspect Follow Snow

and vertical hinge attachment upon reaching Engineering Co.

for loose fasteners; any cracks 3,500 hours time- Service Letter

for loose fasteners; any cracks 3,500 hours time- Service Letter

in the rudder or vertical fin in-service (TIS), 247,

skins, spars, hinges or or within the dated August 14,

brackets, or corrosion. next 100 hours 2005, revised May

TIS after the 17, 2006.

effective date of

this AD,

whichever occurs

later, unless

already done.

Thereafter,

repetitively

inspect every 100

hours TIS.

Installation of

the external

doubler at the

upper rudder

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

is terminating

action for the

repetitive

inspections

required by this

AD.

(2) If you find any damage as a Before further Follow Snow

result of any inspection flight after any Engineering Co.

required by paragraph (e)(1) of inspection Service Letter

this AD, you must: required by 247,

(i) Replace any damaged parts paragraph (e)(1) dated August 14,

with new parts; and of this AD where 2005, revised May

(ii) Do the installation of the you find any 17, 2006, and

external doubler at the upper damaged parts. Snow Engineering

rudder hinge. The installation Co. Process

of the external Specification

doubler at the Number 145, dated

upper rudder December 6, 1991.

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

is the

terminating

action for the

repetitive

inspections

required by this

AD.

(3) Do the installation of the Upon accumulating Follow Snow

external doubler at the upper 5,000 hours TIS Engineering Co.

rudder hinge. or within the Service Letter

next 100 hours 247,

TIS after the dated August 14,

effective date of 2005, revised May

this AD, 17, 2006, and

whichever occurs Snow Engineering

later, unless Co. Process

already done. The Specification

installation of Number 145, dated

the external December 6, 1991.

doubler at the

upper rudder

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

is the

terminating

action for the

repetitive

inspections

required by this

AD.

(4) Do not install any rudder As of the Not Applicable.

without the external doubler at effective date of the upper rudder hinge required this AD. by paragraph (e)(3) of this AD.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Fort Worth Aircraft Certification Office, FAA, ATTN: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19.

Related Information

Related Information

(g) To get copies of the service information referenced in this AD, contact Air Tractor, Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564-5616; facsimile: (940) 564-5612. To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC, or on the Internet at http://dms.dot.gov. The docket number is Docket No. FAA-2006-25260; Directorate Identifier 2006-CE-37-AD.

Issued in Kansas City, Missouri, on August 3, 2006. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.