91 FR 75456 Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all ATR-GIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This proposed AD was prompted by a review of mooring loads that revealed that winds within the currently defined wind profiles could lead to loads exceeding the certification limits on the nose landing gear (NLG) and main landing gear (MLG) while the airplane is moored. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate a revised maintenance procedure (MP) for mooring the airplane. The FAA is proposing this AD to address the unsafe condition on these products.
This document is proposed. It may have been replaced. Check the official source before relying on it.
[Docket No. FAA-2026-13826; Project Identifier MCAI-2025-01613-T] RIN 2120-AA64
Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all ATR-GIE Avions de Transport Régional Model ATR42 and ATR72 airplanes. This proposed AD was prompted by a review of mooring loads that revealed that winds within the currently defined wind profiles could lead to loads exceeding the certification limits on the nose landing gear (NLG) and main landing gear (MLG) while the airplane is moored. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate a revised maintenance procedure (MP) for mooring the airplane. The FAA is proposing this AD to address the unsafe condition on these products.
Dates
DATES: The FAA must receive comments on this proposed AD by January 7, 2027.
ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:
• Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments.
Addresses
• Fax: 202-493-2251.
• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
• Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA-2026-13826; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.
Material Incorporated by Reference:
• For ATR-GIE Avions de Transport Régional material identified in this proposed AD, contact ATR-GIE Avions de Transport Régional, 1 Allée Pierre Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; email aircraft.com">[email protected]; website atr-aircraft.com. It is also available at regulations.gov under Docket No. FAA-2026-13826.
• You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.
For Further Information Contact
FOR FURTHER INFORMATION CONTACT: John Massey, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7320; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments using a method listed under the ADDRESSES section. Include "Docket No. FAA-2026-13826; Project Identifier MCAI-2025-01613-T" at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments.
Comments Invited
Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.
Confidential Business Information
Confidential Business Information
CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as "PROPIN." The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to John Massey, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7320; email: [email protected]. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.
Background
Background
The European Union Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2025-0223R1, dated October 28, 2025 (EASA AD 2025-0223R1) (also referred to as the MCAI), to correct an unsafe condition on all ATR-GIE Avions de Transport Régional Model ATR 42-200, -300, -320, -400, and -500 airplanes and Model ATR 72-101, -102, -201, -202, -211, -212, and -212A airplanes. Model ATR 42-400 airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this proposed AD therefore does not include those airplanes in the applicability. The MCAI states that a review of mooring loads revealed that winds within the currently defined wind profiles could lead to loads exceeding the certification limits on the NLG and MLG while the airplane is moored. This condition, if not addressed, could lead to damage to the NLG steering and retraction systems, which could result in loss of control of the airplane on the ground; and damage to the forward and aft MLG mooring lugs, which could result in MLG mooring lug failure and injury to maintenance personnel during jacking or de-bogging procedures. The MCAI prohibits accomplishing any maintenance action on aircraft using any ATR42 MP task dated earlier than March 18, 2025; or ATR72 MP task dated earlier than August 20, 2025, as applicable.
The FAA is proposing this AD to address the unsafe condition on these products.
You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA-2026-13826.
Material Incorporated by Reference Under 1 CFR Part 51
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed ATR Job Card Package Title ATR42 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 003, dated July 1, 2025, and ATR Job Card Package Title ATR72 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 004, dated January 1, 2026. This material specifies procedures for mooring the airplane and contains the updated wind speed limit of more than 65 knots in any direction. These documents are distinct because they apply to different airplane models.
This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.
FAA's Determination
FAA's Determination
These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI and material referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design.
Proposed AD Requirements in This NPRM
Proposed AD Requirements in This NPRM
This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate a revised MP for mooring the airplane.
Interim Action
The FAA considers that this proposed AD would be an interim action. If final action is later identified, the FAA might consider further rulemaking.
Costs of Compliance
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would affect 45 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:
The FAA has determined that revising the existing maintenance or inspection program takes an average of 90 work-hours per operator, although the agency recognizes that this number may vary from operator to operator. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), the FAA has determined that a per-operator estimate is more accurate than a per-airplane estimate. Therefore, the FAA estimates the average total cost per operator to be $7,650 (90 work-hours x $85 per work-hour).
Authority for This Rulemaking
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
Regulatory Findings
The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
(1) Is not a "significant regulatory action" under Executive Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. The FAA amends § 39.13 by adding the following new airworthiness directive:
ATR-GIE Avions de Transport Régional: Docket No. FAA-2026-13826; Project Identifier MCAI-2025-01613-T.
(a) Comments Due Date
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive (AD) by January 7, 2027.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all ATR-GIE Avions de Transport Régional airplanes, certificated in any category, as identified in paragraphs (c)(1) and (2) of this AD.
(c) Applicability
(1) Model ATR42-200, -300, -320, and -500 airplanes.
(2) Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes.
(d) Subject
Air Transport Association (ATA) of America Code 10, Parking, mooring, and storage.
(e) Unsafe Condition
This AD was prompted by a review of mooring loads that revealed that winds within the currently defined wind profiles could lead to loads exceeding the certification limits on the nose landing gear (NLG) and main landing gear (MLG) while the airplane is moored. The FAA is issuing this AD to address loads exceeding the certification limits on the NLG and MLG while the airplane is moored. The unsafe condition, if not addressed, could lead to damage to the NLG steering and retraction systems, which could result in loss of control of the airplane on the ground; and damage to the forward and aft MLG mooring lugs, which could result in MLG mooring lug failure and injury to maintenance personnel during jacking or de-bogging procedures.
(f) Compliance
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Revision of Existing Maintenance or Inspection Program
Within 30 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in the material identified in paragraphs (g)(1) and (2) of this AD, as applicable.
(g) Revision of Existing Maintenance or Inspection Program
(1) ATR Job Card Package Title ATR42 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 003, dated July 1, 2025.
(2) ATR Job Card Package Title ATR72 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 004, dated January 1, 2026.
(h) Provisions for Alternative Actions
After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions are allowed unless they are approved as specified in paragraph (i)(1) of this AD.
(i) Additional AD Provisions
(i) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD and email to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or ATR-GIE Avions de Transport Régional's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(j) Additional Information
(j) Additional Information
For more information about this AD, contact John Massey, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7320; email: [email protected].
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(k) Material Incorporated by Reference
(2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise.
(i) ATR Job Card Package Title ATR42 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 003, dated July 1, 2025.
(ii) ATR Job Card Package Title ATR72 MP ATR-A-10-2X-XX-00001-17AA-A, "Mooring," Issue Number 004, dated January 1, 2026.
(3) For ATR-GIE Avions de Transport Régional material identified in this AD, contact ATR-GIE Avions de Transport Régional, 1 Allée Pierre Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; email aircraft.com">[email protected]; website atr-aircraft.com.
(4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.
(5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].
Issued on November 18, 2026. Steven W. Thompson, Acting Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service.