Radar Vectors
Final Rule Current Issued Nov 18, 2026 17 pages Copy saved Nov 19, 2026

91 FR 74070 Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

This document announces the availability of ASTM International (ASTM) consensus standards for use as an FAA-accepted means of compliance (MOC) to the applicable airworthiness standards for normal category airplanes. The FAA accepts ASTM F3264-25, "Standard Specification for Normal Category Aeroplanes Certification," with changes identified in this document.

Official source ↗ Official PDF ↗

14 CFR Part 23

[Docket No. FAA-2026-6604]

Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notification of availability (NOA).

SUMMARY: This document announces the availability of ASTM International (ASTM) consensus standards for use as an FAA-accepted means of compliance (MOC) to the applicable airworthiness standards for normal category airplanes. The FAA accepts ASTM F3264-25, "Standard Specification for Normal Category Aeroplanes Certification," with changes identified in this document.

Dates

DATES: Acceptance of the means of compliance is effective on November 18, 2026.

FOR FURTHER INFORMATION CONTACT: Hieu Nguyen, AIR-690, General Aviation, VTOL & Engine Standards Branch, Certification Standards Division, Aircraft Certification Service, Federal Aviation Administration, 1100 Main Street, Suite 800, Kansas City, MO 64105; telephone: (316) 946-4123; email: [email protected].

Supplementary Information

SUPPLEMENTARY INFORMATION:

Background

Under the provisions of the National Technology Transfer and Advancement Act of 1995 and Office of Management and Budget (OMB) Circular A-119, "Federal Participation in the Development and Use of Voluntary Consensus Standards and in Conformity Assessment Activities," effective January 27, 2016, the FAA participates in the development of consensus standards for use as a means of carrying out its policy objectives where appropriate.

Background

Consistent with the Small Airplane Revitalization Act of 2013, the FAA has been working with industry and other stakeholders through the ASTM F44 Committee on General Aviation Aircraft to develop consensus standards as a MOC in certificating small airplanes under part 23.

In part 23, amendment 23-64 (81 FR 96572), published on December 30, 2016, the final rule stated the FAA would publish an NOA of those consensus standards in the Federal Register when the Administrator accepts the consensus standards as an acceptable MOC. The FAA reviewed the published ASTM consensus standards developed by the ASTM F44 Committee on General Aviation Aircraft as the basis for a MOC to 65 sections of part 23, amendments 23-64 and 23-65. In some cases, the Administrator found sections of ASTM F3264-25, without changes, are accepted as a MOC for the airworthiness requirements of part 23, amendments 23-64 and 23-65. In other cases, the MOC, while based on ASTM consensus standards, includes additional FAA provisions necessary to comply with the airworthiness requirements of part 23, amendments 23-64 and 23-65.

Part 23, amendment 23-64, established airworthiness requirements based on the safety requirements outlined in amendment 23-63, except in areas that address loss of control and icing, where the FAA increased the safety level. Depending on the details of a design, the applicant may require use of a different MOC beyond those accepted by this NOA. For example, novel airplane designs, such as unmanned airplanes, or other special class aircraft, such as powered-lift, are beyond the scope of this NOA, and applicants may need to propose an alternative MOC applicable to their designs accepted under § 23.2010.

Means of Compliance Accepted

Means of Compliance Accepted

The FAA accepts only the revisions of the standards referenced in ASTM F3264-25, "Standard Specification for Normal Category Aeroplanes Certification," as a MOC for part 23, amendments 23-64 and 23-65, with the changes identified in Table 1. For ease of use, Table 2 was added to provide a side-by-side view, linking the applicable part 23 regulation to the ASTM F3264-25 section.

Guidance

Guidance

This is a guidance document. Its content is not legally binding in its own right and will not be relied upon by the Department as a separate basis for affirmative enforcement action or other administrative penalty. Conformity with the guidance document is voluntary only, and nonconformity will not affect rights and obligations under existing statutes and regulations.

Table 1--Part 23 Accepted MOC Based on ASTM Consensus Standards

Changes required for FAA

ASTM No. as identified in F3264-25 ASTM document title acceptance Additional information

F2490-20 … Standard Guide for Replace "should" with

Aircraft Electrical "must" throughout

Load and Power document for regulatory

Source Capacity compliance.

Analysis. Replace F2490-20 paragraph

2.1 with:.

"2.1 FAA Aeronautics and

Space Airworthiness

Standards: 2.

14 CFR 23.2510 'Equipment,

systems and

installations'.

14 CFR 23.2525 'System

power generation,

storage, and

distribution'.

14 CFR 23.2540 'Flight in

icing conditions'.

14 CFR Appendix A of part

23 'Instructions for

Continued Airworthiness'.

14 CFR 91 'General

Operating and Flight

Rules'.

14 CFR 135.163 'Operating

Requirements: Commuter

and On Demand Operations

and Rules Governing

Persons on Board Such

Aircraft--Equipment

Requirements: Aircraft

Carrying Passengers under

IFR ",

Replace in section 6.4.1.3

the statement "Assume

"night" conditions as

the worst-case scenario"

with "Assume the worst-

case scenario is based on

the criticality of the

system safety

assessment".

Add Lithium-Ion battery

data to Figure 1.

F3061/F3061M-25 … Standard The tables defining The tables defining

Specification for applicability of applicability found in

Systems and requirements in sections F3061/F3061M-25 sections

Equipment in Small 4.1.6, 4.2.3.3, 4.2.6, 4.1.6, 4.2.3.3, 4.2.6,

Aircraft. 4.2.8, 4.2.8.1, 4.2.8.2, 4.2.8, 4.2.8.1, 4.2.8.2,

4.3.1, 4.3.2.1, 4.3.2.2, 4.3.1, 4.3.2.1, 4.3.2.2,

4.4, 10.1, 10.1.1, 4.4, 10.1, 10.1.1,

10.1.2, 10.1.3, 10.1.4, 10.1.2, 10.1.3, 10.1.4,

10.3.3, 10.3.4, 10.3.5, 10.3.3, 10.3.4, 10.3.5,

10.3.6, 10.3.7, 10.3.8, 10.3.6, 10.3.7, 10.3.8,

10.3.9, 10.4.2, 10.4.3, 10.3.9, 10.4.2, 10.4.3,

10.4.4, 10.7.1, 10.7.2, 10.4.4, 10.7.1, 10.7.2,

10.7.3, 10.7.4, 10.7.5, 10.7.3, 10.7.4, 10.7.5,

10.7.6, 10.7.7, 0.7.7.1, 10.7.6, 10.7.7,

10.8, 13.1.1, 13.1.2, 10.7.7.1, 10.8, 13.1.1,

17.1.1, 17.1.2, 17.1.3, 13.1.2, 17.1.1, 17.1.2,

17.2.1, 17.2.2, 17.2.3, 17.1.3, 17.2.1, 17.2.2,

17.3.1.1, 17.3.1.2, 17.2.3, 17.3.1.1,

17.3.1.3, 17.3.1.4, and 17.3.1.2, 17.3.1.3,

18.4 are not accepted. 17.3.1.4, and 18.4 are

Applicability will be not accepted.

determined by the Policy Applicability will be

and Standards determined by the Policy

DivisionReplace 17.3.1.1 and Standards Division.

with: Aircraft certification

(a) Each electrical or levels are as defined in

electronic system that 14 CFR 23.2005.

performs a function, the F3061/F3061M-25 does not

failure of which would contain means for

prevent the continued showing compliance to

safe flight and landing Sec. 23.2310, Buoyancy

of the airplane, must be for seaplanes and

designed and installed amphibians. If applying

such that--(1) The for certification of a

function at the airplane seaplane or amphibian,

level is not adversely applicants may use the

affected during and after provisions of Sec. Sec.

the time the airplane is 23.751, 23.755, and

exposed to lightning; and. 23.757 at amendment 23-

(2) The system recovers 63 as a means of

normal operation of that complying with Sec.

function in a timely 23.2310 or may obtain

manner after the airplane FAA acceptance of a

is exposed to lightning different MOC in

unless the system's accordance with Sec.

recovery conflicts with 23.2010.

other operational or For normal category

functional requirements airplanes with electric

of the system. propulsion, the Policy

Replace 17.3.1.2 with:.... and Standards Division

(b) Each electrical and will determine

electronic system that airworthiness criteria

performs a function, the and acceptable

failure of which would compliance approaches.

significantly reduce the

capability of the

airplane or the ability

of the flight crew to

respond to an adverse

operating condition, must

be designed and installed

such that the system

recovers normal operation

of that function in a

timely manner after the

airplane is exposed to

lightning.

Remove 17.3.1.3, 17.3.1.4,

and 18.4..

F3062/F3062M-25 … Standard None …

Specification for

Aircraft Powerplant

Installation.

F3063/F3063M-24 … Standard None …

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

F3064/F3064M-24 … Standard None …

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

F3065/F3065M-21a … Standard None …

Specification for

Aircraft Propeller

System Installation.

F3066/F3066M-25 … Standard None …

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

F3082/F3082M-23a … Standard None …

Specification for

Weights and Centers

of Gravity of

Aircraft.

F3083/F3083M-25 … Standard Replace 4.1.6 with:

Specification for Powerplant and ESS mounts

Emergency and supporting structures

Conditions, Occupant must withstand 18.0 g

Safety and forward for powerplants

Accommodations. and ESS installed behind

and above the seating

compartment.

F3093/F3093M-24e1 … Standard None …

Specification for

Aeroelasticity

Requirements.

F3114-21 … Standard None …

Specification for

Structures.

F3115/F3115M-23e1 … Standard Replace 4.4.3.3 with: If the applicant proposes

Specification for The residual strength to use F3115/F3115M-20

Structural evaluation must show that sections 4.3 or 6.3.2,

Durability for Small the remaining structure the Policy and Standards

Aeroplanes. is able to withstand the Division will be

residual strength loads involved as the standard

in 4.5 with the extent of is applied during

detectable damage projects to review the

consistent with the approach to determining

results of the damage similarity (F3115/F3115M-

tolerance evaluations. 20 section 4.3) and

The residual strength criteria defining

demonstrated for obvious damage (F3115/

inspectable damage shall F3115M-20 section

be sufficiently above 6.3.2).

limit loads in 4.5 and If the applicant proposes

should consider variables to use F3115/F3115M-23e1

such as the severity of sections 4.1.3 or

damage, inspection 4.3.3.2, the Policy and

interval, and inspection Standards Division will

method. This level of be involved as the

residual strength standard is applied

demonstrated should also during projects to

account for material review the approach to

variability, damage, determining similarity

growth rate, and (F3115/F3115M-23e1

environmental effects. section 4.1.3) and

Guidance for no growth, criteria defining

slow growth, or arrested obvious damage (F3115/

growth can be found in F3115M-23e1 section

documents X2.3 and X2.4. 4.3.3.2).

Replace 4.4.1.1 with: … Note: Composite structure

For all airplanes the needs to be damage

methods described in tolerant. If

4.4.3 are applicable. impractical, safe life

Delete 4.4.1.2. Revised methods may be used.

paragraphs as follows:. Means of compliance must

4.4.1.2 For aeroplanes reflect this.

evaluated to the damage F3115-20.

tolerance criteria of Replace section 7.1 with:

4.4.3 if it is shown that 4.4.1.3 For all aeroplane

the damage tolerance is levels, the effects of

impractical for a material variability and

particular structure, the environmental conditions

structure may be on the strength and

evaluated in accordance durability properties of

with the methods the material must be

described in 4.4.2. considered

4.4.1.4 For all aeroplane

levels, the evaluation

in either 4.4.2 or

4.4.3 must show that

catastrophic failure due

to fatigue,

environmental effects,

manufacturing defects,

or accidental damage

will be avoided

throughout the

operational life of the

aircraft

7.1 Composite components

must be evaluated as

follows:

7.1.1 For all aeroplanes,

the methods described in

7.3 are applicable.

7.1.2 For aeroplanes

evaluated to the damage

tolerance criteria of

7.3: if it is shown that

damage tolerance is

impractical for a

particular structure,

the structure may be

evaluated in accordance

with the methods

described in 7.2.

7.1.3 For all aeroplane

levels, the effects of

material variability and

environmental conditions

on the strength and

durability properties of

the materials must be

considered.

7.1.4 For all aeroplane

levels, the evaluations

in either 7.2 or 7.3

must show that

catastrophic failure due

to fatigue,

environmental effects,

manufacturing defects,

or accidental damage

will be avoided

throughout the

operational life of the

aircraft.

F3116/F3116M-24 … Standard Replace 4.1.4 with: …

Specification for Appendix X1 through

Design Loads and Appendix X4 provides,

Conditions. within the limitations

specified within the

appendix, a simplified

MOC with several of the

requirements set forth in

sections 4.2 to 4.26 and

7.1 to 7.9 that can be

applied as one (but not

the only) means to

comply. If the simplified

methods in Appendix X1

through X3 are used, they

must be used together in

their entirety.

Replace X1.1.1 with:

The methods provided in

this appendix provide one

possible means (but not

the only possible means)

of compliance and can

only be applied to Level

1 and Level 2 low speed

airplanes.

Replace X2.1.1 with: …

The methods provided in

this appendix provide one

possible means (but not

the only possible means)

of compliance and can

only be applied to Level

1 and Level 2 low speed

airplanes.

Replace X3.1.1 with: …

The methods provided in

this appendix provide one

possible means (but not

the only possible means)

of compliance and can

only be applied to Level

1 and Level 2 low speed

airplanes.

Replace X4.1.1 with: …

The methods provided in

this appendix provide one

possible means (but not

the only possible means)

of compliance and can

only be applied to Level

1 low speed airplanes.

F3117/F3117M-25a … Standard None …

Specification for

Crew Interface in

Aircraft.

F3120/F3120M-24 … Standard None …

Specification for

Ice Protection for

General Aviation.

F3173/F3173M-24 … Standard None …

Specification for

Aircraft Handling

Characteristics.

F3174/F3174M-21 … Standard None …

Specification for

Establishing

Operating

Limitations and

Information for

Aeroplanes.

F3179/F3179M-24a … Standard None …

Specification for

Performance of

Aircraft.

F3180/F3180M-25 … Standard Replace 4.2 with: The FAA is committed to

Specification for 4.2 Single-engine lowering the loss of

Low-Speed Flight aeroplanes that are not control accident rate

Characteristics of certified for aerobatics and is effecting this by

Aircraft. shall demonstrate ensuring that accepted

Enhanced Single Engine standards are tailored

Low-Speed Characteristics to address the low

(Section 6). altitude loss of control

Replace 5.1(6)(b) with:... scenario that accounts

(b) For turbine engine for the majority of part

powered airplanes: no 23 loss of control

less than the maximum accidents.

engine thrust that is Applicants may propose

continuously available. elements of the

Replace 5.1(6)(c) with:... Departure Aversion for

(c) In all cases, to avoid Light Aircraft standard

extreme pitch attitudes, contained in F3180/

if the power/thrust F3180M-25, or other

requirements in (a) and means, for development

(b), above, for a given of their project means

configuration results in of compliance to 14 CFR

nose-high attitudes 23.2150 in accordance

exceeding 30° pitch with 14 CFR 23.2010.

attitude prior to the 5.3.2(3) If, in the

stall, the thrust/power judgement of the test

setting may be limited to pilot, the aeroplane

one that results in not exhibits adequate roll

more than 30° pitch control to prevent large

attitude but maintains excursions past wings-

greater than 25° level the stall

pitch attitude until characteristics may be

stall during a wings- deemed acceptable.

level stall technique for 6.2.3 The FAA considers

a given configuration. that the Spin Resistance

That established "Power/ MOC previously accepted

Thrust On" setting shall does not need to be

then be used for wings- dependent on a points

level, turning flight, system and need not

and accelerated turning require additional

stalls flown under the Safety Enhancing

same configuration, Features nor Enhanced

weight, altitude and Stall Warning to

temperature. demonstrate compliance

Replace 5.2.4 with: … to 14 CFR 23.2150

5.2.4 During the entry 6.2.6.3 Descent arrest

into and the recovery systems are not

from stalls performed considered as a showing

below 7620 m [25 000 ft], of compliance to 14 CFR

it shall be possible to 23.2150.

prevent more than 20°

of roll or heading change

by the normal use of

controls.

Replace 5.3.2(3) with:

(3) For both turning

flight, and accelerated

turning, stalls,

exceeding a bank angle of

60° in the original

direction of the turn or

exceeding 0° (wings-

level) in the opposite

direction.

Remove 5.3.2(4) …

6.2 The FAA does not

universally accept the

Departure Aversion

Standard for Light

Aircraft contained in

F3180/F3180M-25.

Replace 6.2.3 with:

6.2.3 Spin Resistance--

Aeroplanes may

demonstrate that the

aeroplane does not have a

tendency to inadvertently

depart controlled flight

by demonstrating the

following maneuvers. In

all cases, maneuvers can

be discontinued, and a

normal recovery

initiated, after a

downward pitching motion

of the aeroplane

commences due to the

activation of a stall

barrier device (for

example, stick pusher

activation).

Remove 6.2.6.3 Descent

Arrest Systems.

F3227/F3227M-25 … Standard None …

Specification for

Environmental

Systems in Small

Aircraft.

F3228-21(2025) … Standard Remove: Table 1 … Aircraft Type Code

Specification for compliance matrix table

Flight Data and found in F3228-21(2025)

Voice Recording in is not accepted.

Small Aircraft. Applicability will be

determined by the Policy

and Standards Division.

F3229/F3229M-23a … Standard Practice for Remove: Table 1 … Aircraft Type Code

Static Pressure compliance matrix table

System Tests in found in F3229/F3229M-

Small Aircraft. 23a is not accepted.

Applicability will be

determined by the Policy

and Standards Division.

F3230-25 … Standard Practice for None …

Safety Assessments

of Systems and

Equipment in Small

Aircraft.

F3231/F3231M-24 … Standard Remove: Table 1 … Aircraft Type Code

Specification for Remove section 4.1.1.3 and compliance matrix table

Electrical Systems 4.1.1.4. found in F3231/F3231M-24

for Aircraft with Replace 4.2.13 with: is not accepted.

Combustion Engine "Electrical equipment Applicability will be

Electrical Power shall be designed and determined by the Policy

Generation. installed so that in the and Standards Division.

event of a fire in the

engine compartment,

during which the surface

of the firewall adjacent

to the fire is heated to

1095 °C [2000 °F]

for 15 min or follow AC

20-135 in compliance to

23.2440(c), the equipment

essential to continued

safe operation and

located behind the

firewall will function

satisfactorily and will

not create an additional

fire hazard. For Lithium-

Ion batteries, utilize

the following

documentation: Non-

Rechargeable Lithium

Battery Means of

Compliance--CPP-23.2525-1

, Rechargeable Lithium

Battery Means of

Compliance--CPP-23.2525-2

, Rechargeable Lithium

Battery Method of

Compliance--CPP-23.2525-3

, Non-Rechargeable

Lithium Battery Method of

Compliance--CPP-23.2525-4

".

F3232/F3232M-25a … Standard None …

Specification for

Flight Controls in

Small Aircraft.

F3233/F3233M-23b … Standard Remove: Table 1 … Aircraft Type Code

Specification for compliance matrix table

Flight and found in F3233/F3233M-

Navigation 23b is not accepted.

Instrumentation in Applicability will be

Aircraft. determined by the Policy

and Standards Division.

F3234/F3234M-21(2025) … Standard Remove: Table 1 … Aircraft Type Code

Specification for compliance matrix table

Exterior Lighting in found in F3234/F3234M-

Small Aircraft. 21(2025) is not

accepted. Applicability

will be determined by

the Policy and Standards

Division.

F3235-22 … Standard Replace section 2 with: If applying for

Specification for "2.1 Following is a list certification of an

Aircraft Storage of external standards airplane with installed

Batteries. referenced throughout lithium batteries,

this specification; the applicants may use the

earliest revision guidance provided by

acceptable for use is RTCA/DO-311A or may

indicated. In all cases, obtain FAA acceptance of

later document revisions a different MOC in

are acceptable if shown accordance with Sec.

to be equivalent to the 23.2010.

listed revision, or if Aircraft Type Code

otherwise formally compliance matrix table

accepted by the governing found in F3235-22 is not

civil aviation authority; accepted. Applicability

earlier revisions are not will be determined by

acceptable. the Policy and Standards

2.2 ASTM Standards:2 … Division.

F3060 Terminology for

Aircraft.

F3061/F3061M Specification

for Systems and Equipment

in Aircraft..

2.3 EASA Standard:3

CS-23 Normal, Utility,

Aerobatic and Commuter

Aeroplanes.

2.4 FAA Standard:4

14 CFR Part 23

Airworthiness Standards:

Normal Category Airplanes.

2.5 RTCA Standard:5

RTCA/DO-311A Minimum

Operational Performance

Standards for

Rechargeable Lithium

Batteries and Battery

Systems.

2.6 RTCA DO-293A:

Minimum Operational

Performance Standards

(MOPS) for Nickel-

Cadmium, Nickel Metal-

Hydride and Lead-Acid

Batteries".

Replace section 4.1.2

with:

"4.1.2 Nickel cadmium

battery installations

capable of being used to

start an engine or

auxiliary power unit must

meet the requirements of

either 4.1.2.1, 4.1.2.2,

or 4.1.2.3. Follow

guidance in RTCA 293A."

Remove: Section 4.2 …

Remove: Table 1 …

Remove A1.1, A1.2, and

A1.3.

F3236-21a … Standard Remove: Table 1 … Aircraft Type Code

Specification for compliance matrix table

High Intensity found in F3236-21a is

Radiated Field not accepted.

(HIRF) Protection in Applicability will be

Small Aircraft. determined by the Policy

and Standards Division.

For normal category

airplanes with electric

propulsion, fly-by-wire

flight controls, or

highly integrated

systems, coordinate with

the Policy and Standards

Division to determine

acceptable compliance

approaches.

F3239-22a … Standard The FAA does not Applicants may propose

Specification for universally accept F3239- F3239-22a for

Aircraft Electric 22a. development of their MOC

Propulsion Systems. for electric propulsion

systems on a project-by-

project basis. Any MOC

proposed must receive

acceptance by the FAA in

accordance with Sec.

23.2010.

F3254-22 … Standard Figures 2, 3, and 4 Other proposed

Specification for Replace: "Remote" with: probabilities will be

Aircraft Interaction "10-5". considered by the FAA on

of Systems and Replace: "Extremely a case-by-case basis.

Structures. Improbable" with: "10-

8" for Level 1, 2, and 3

airplanes and with "10-

9" for Level 4 airplanes.

F3309/F3309M-24a … Standard Practice for None …

Simplified Safety

Assessment of

Systems and

Equipment in Small

Aircraft.

F3316/F3316M-19 … Standard FAA does not universally Applicants may propose

Specification for accept F3316/F3316M-19. F3316/F3316M-19 for

Electrical Systems Remove: Table 1 … development of their MOC

for Aircraft with for electrical systems

Electric or Hybrid- installed on airplanes

Electric Propulsion. with electric or hybrid-

electric propulsion

systems on a project-by-

project basis.

Applicants may obtain

FAA acceptance of a

different MOC in

accordance with Sec.

23.2010.

Aircraft Type Code

compliance matrix table

found in F3316/F3316M-19

is not accepted.

Applicability will be

determined by the Policy

and Standards Division.

F3331-18(2023) … Standard Practice for None …

Aircraft Water Loads.

F3367-23 … Standard Practice for Replace 5.1.1 with: For normal category

Simplified Methods Systems that are part of airplanes with electric

for Addressing High- the Type Certificated propulsion, fly-by-wire

Intensity Radiated Engine must be installed flight controls, or

Fields (HIRF) and in accordance with the highly integrated

Indirect Effects of engine manufacturer's systems, coordinate with

Lightning on requirements. The minimum the Policy and Standards

Aircraft. HIRF and lightning Division to determine

qualification in acceptable compliance

accordance with sections approaches.

8 and 9 of this ASTM

practice should be met at

the aircraft level,

except for engine control

systems in Level 1 and 2

airplanes, which should

meet the following:.

HIRF: DO-160, section 20-R

for both radiated and

conducted susceptibility.

Lightning: Utilize

guidance in AC 33.28-3.

For metallic fuselage DO-

160G, section 22-A3J3L3

(shielded) and A3H3L3

(unshielded).

For composite fuselage DO-

160G, section 22-B3K3L3

(shielded) and B3H3L3

(unshielded).

Use of lower HIRF and

lightning induced voltage

and current levels may be

acceptable for electronic

engine control systems if

substantiated at the

airplane level (by test

in the proposed

installation or similar)

when exposed to external

HIRF environment per AC

20-158 (latest revision)

and lightning per AC 20-

136 (latest revision),

using shielding and

grounding of the

electronic engine control

system and accessories in

the given installation.

Remove 8.2.2.2, 8.2.3.3,

9.2.5.2, and 9.2.7.2.

F3380-19 … Standard Practice for None …

Structural

Compliance of Very

Light Aeroplanes.

F3396/F3396M-23a … Standard Practice for None …

Aircraft Simplified

Loads.

F3397/F3397M-21 … Standard Practice for None …

Aeroplane Turbine

Fuel System Hot

Weather Operations.

F3408/F3408M-21 … Standard None …

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

F3432-20a … Standard Practice for None …

Powerplant

Instruments.

F3454-25 … Standard Practice for None …

Alerting Methods in

Aircraft.

F3491-25 … Standard Practice for None …

Enhanced Indication

Methods in Aircraft.

F3498-21 … Standard Practice for None …

Developing

Simplified Fatigue

Load Spectra.

F3532-25 … Standard Practice for None …

Protection of

Aircraft Systems

from Intentional

Unauthorized

Electronic

Interactions.

F3601-23 … Standard Practice for None …

Structural Finite

Element Model

Verification and

Validation.

F3643-25 … Standard Practice for None …

Pilot Compartment

View in

Precipitation.

F3651/F3651M-23 … Standard Practice for None …

Determining Safe-

Life, Inspection

Threshold and

Recurring Inspection

Intervals.

F3653-24 … Standard Replace ASTM F3653-24

Specification for section 4.1.2.1 with:

Installation of "F3653-24, sections 4.1.1

Rechargeable Lithium and 4.1.2 can be met by

Batteries of showing that the battery

Aircraft. or battery system meets

the requirements in RTCA/

DO-311A, 2.2, Equipment

Requirements--Standard

Conditions using the test

procedures in RTCA/DO-

311A, 2.4, Equipment Test

Procedures. The applicant

or the foreign civil

aviation authority (FCAA)

is to provide the FAA

with the video of the

testing conducted for

RTCA/DO-311A section

2.4.5.5; and ".

Replace section 4.1.3

with:

"Not emit explosive or

toxic gases, either in

normal operation or as a

result of its failure,

that may accumulate in

hazardous quantities

within the aircraft. To

determine whether an

aircraft venting system

is appropriate, consider

the results of RTCA/DO-

311A, section 2.4.5.5,

and whether some cells or

all cells achieved

thermal runaway.".

Replace section 4.1.3.3

with:.

"F3653-24, section 4.1.3

can be met by Venting

Category B per RTCA/DO-

311A when not completely

vented overboard if

explosive or toxic

emissions can be shown to

not accumulate in

hazardous quantities

within the aircraft; or

an acceptable method of

compliance includes using

the tests results

required under F3653-24,

sections 4.1.2.1, 4.1.2.2

and 4.1.2.2 (a)

(including RTCA/DO-311A,

section 2.4.5.5 test

results) to demonstrate

that all emitted gases

are contained or vented

completely overboard

(i.e., vented completely

outside the aircraft)

through designed vent

ports. If the design has

ports to vent gases

overboard completely,

show that there are means

to protect ground

personnel from exposure

to these gases and to

prevent re-ingestion, for

example through engine in-

take or air conditioning

in-take. Reference FAA

TSO-C179b, Class A vs.

Class B, as one method of

classifying the results

of the thermal runaway

testing; or".

Replace 4.1.3.4 with:

"F3653-24, section 4.1.3

can be met by Venting

Category C per RTCA/DO-

311A if explosive or

toxic emissions can be

shown to not accumulate

in hazardous quantities

within the aircraft. For

Category C provide the

volume of gas and the

constituents of the gas

per the reporting

criteria of RTCA/

DO-311A section

2.4.5.5 and section F3653-

24, section 4.1.2.1".

Replace section 4.1.4.1

with:

"F3653-24, section 4.1.4

can be met (that is,

demonstrates minimizing

the probability of

flammable fluid and vapor

release, and thus the

probability of ignition)

by complying with F3653-

24, section 4.1.3.1 or

F3653-24, section

4.1.3.2; Defining the

location of where

flammable fluids or

vapors might escape by

leakage is required by

(14 CFR 23.2325(g)) and;

both battery electrolyte

and any coolant fluid, if

present, are considered

fluid systems when

evaluating 14 CFR

23.2325(g) and;

performing a safety

assessment to identify

and evaluate associated

hazards and their

severity, as well as

mitigation and

minimization of all

hazards resulting from a

battery failure is

required. Additional

requirements may be

needed depending upon the

safety assessment of the

installation location of

the battery; or".

Delete in sections 4.1.5

and 4.1.5.2 "major or

more severe".

Replace section 4.1.5.3

with:

"F3653-24, section 4.1.5

can be met by Venting

Category C per RTCA/DO-

311A if emitted fluids

and gases can be shown to

not be corrosive in such

a way as to cause any

failure:

To support F3653-24,

section 4.1.5.2 or F3653-

24, section 4.1.5.3, show

that if fluid escapes the

battery, it is not

corrosive or it is

managed in a way (for

example, contained,

isolated, drained, or

vented, etc.) that

protects the surrounding

structure and adjacent

systems, equipment,

components, and

electrical wiring. To

support F3653-24, section

4.1.5.2 or F3653-24,

section 4.1.5.3, test

results of RTCA/DO-311A,

2.4.5.5 may be useful to

show substantiation, if

information regarding the

corrosive nature of

emissions is captured.

Mitigation at the

aircraft level may also

be applied in addition to

F3653-24, sections

4.1.5.1 through 4.1.5.3

to bring the design into

compliance with F3653-24,

section 4.1.5. Include

results of test performed

during ASTM F3653-24

sections 4.1.2.1, 4.1.2.2

and 4.1.2.2(a) for

section 4.1.5

substantiation".

Replace 4.1.6.1 with:

"F3653-24, section 4.1.6

can be met by showing

that the heat and any

related effects from a

worst-case thermal

runaway event do not

create a hazard to the

structure or systems of

the aircraft, or that the

hazard can be mitigated

at the aircraft level.

(a) The maximum external

temperature of the

battery from a worst-case

thermal runaway event can

be obtained by conducting

and complying with RTCA/

DO-311A, 2.4.5.5.

Inclusion of results for

tests performed during

ASTM F3653-24 sections

4.1.2.1, 4.1.2.2, and

4.1.2.2(a), meet RTCA/

DO-311A as well as

the inclusion of

temperature of the gases

and the enclosure is

required".

Replace 4.1.7 with:

"Have a failure sensing

and alerting system with

adequate indication to

the flight crew if its

failure affects safe

operation of the

aircraft. Ensure adequate

flight crew alerting

because failure effects

of a battery installation

to airplane level

functions could result in

unsafe system operating

conditions. Reference

RTCA/DO-311A, section

2.1.4.2, Battery Warning

Features that discuss

warning circuits and

signals".

Replace section 4.1.7.1

with:

"Have monitoring and an

alert for the flight crew

when the battery power

falls below acceptable

levels if its function is

required for safe

operation of the

aircraft. Have a means

for the flight crew and

maintenance personnel to

determine the power if

the battery's function is

required for safe

operation of the

aircraft. Use a safety

assessment system to

determine the alert

level. Reference Practice

F3230 and Specification

F3061/F3061M for guidance

on conducting the hazard

assessment of the

failure. If required by

the hazard assessment,

incorporate alerting in

accordance with

Specification F3117/

F3117M, 11.2, or

similar."

Replace section 4.1.8

with:

"Have a means to

disconnect from its

charging source in the

event of an over-

temperature condition,

cell failure or battery

failure".

Replace section 4.1.8.1

with:

"F3653-24, section 4.1.8

can be met by

demonstrating that the

battery or battery system

is capable of

automatically

disconnecting from the

charging source in the

event of an over-

temperature condition,

cell failure or battery

failure, or".

Remove section 4.1.8.2....

Replace section 5 with:

"F3653-24, section 5.1

When preparing

Instructions for

Continued Airworthiness,

the following shall be

addressed:

F3653-24, section 5.1.1

Operational requirements

shall be defined that

address the necessary

condition of the battery

for continued use on the

aircraft in accordance

with the battery

manufacturer's

requirements and

recommendations and

airworthiness

requirements. Maintenance

requirements to replace

each rechargeable lithium

battery within an

interval that will ensure

there is sufficient

charge to power equipment.

F3653-24, section 5.1.2

Maintenance requirements,

as applicable, to define

the procedure and

interval necessary to

avoid damage to the

battery and retain its

operational capability

during storage or

extended non-use on the

aircraft in accordance

with the battery

manufacturer's

requirements and

recommendations and

aircraft maintenance

manual. A requirement to

only replace rechargeable

lithium batteries with

batteries from the same

manufacturer with the

same part number or to

obtain a new FAA approval

for installing a

different battery.

F3653-24, section 5.1.3

Precautions to prevent

mishandling of

replacement rechargeable

lithium batteries prior

to their installation

which could result in

short-circuit or other

unintentional damage.

Procedures are in place

to ensure that each

rechargeable lithium

battery has not:

--Experienced degraded

charge retention ability

or other damage during

storage.

--Been damaged from

environmental or physical

impacts such as

mechanical shock,

vibration, heat and

possible abuses

encountered during

storage, transportation

prior to their

installation or

maintenance activities on

or around them.

Precautions to prevent

mishandling of

replacement rechargeable

lithium batteries prior

to their installation

which could result in

short-circuit or other

unintentional damage."

Replace section 6.1 with:

"If the battery

installation falls within

a rotor burst zone, an

analysis shall consider

the impact of uncontained

high-energy fragments

(ref: AC 20-128A Design

Considerations for

Minimizing Hazards caused

by Uncontained Turbine

Engine and Auxiliary

Power Unit Rotor) with

respect to any potential

additional hazard that

may result. The FAA

requires the utilization

of results of tests

performed for ASTM F3653-

24 sections 4.1.2.1,

4.1.2.2 and 4.1.2.2(a).

Installation in a

Designated Fire Zone

(DFZ), such as an engine

compartment, should be

avoided, but may be

acceptable, if the

battery location does not

create an additional

hazard. Alternatively,

the battery is to be

located outside of the

rotor burst zone. The

battery must contain and/

or vent any thermal

runaway, and prevent

introduction of

additional hazards, when

exposed to a 2000 °F

flame for 15 minutes.

Test by exposing the

battery installation

design (including any

vents) to a 2000 °F

flame for 15 minutes per

AC 20-135. Ensure no

additional hazards are

introduced. Some examples

are: a) Directing and

venting (if the design

includes a vent) any

potential flames or

flammable material from

the battery out of the

fire zone. Any vent

system included in the

design must continue to

function in the event of

a thermal runaway of the

battery, otherwise it

must not create an

additional hazard from

its failure. b) Using

fireproof materials in

the construction of the

battery installation

design. c) Providing

adequate shielding to

protect the battery and

vent, if any, from direct

flames to ensure the

battery remains below a

temperature that could

compromise the thermal

runaway containment

integrity when exposed to

a powerplant fire

condition".

F3653-24, section 6.1.1

Rechargeable coin or

button cells with less

than 2 watt-hours of

energy that meet UL 1642,

UL 2054, or IEC 62133 are

exempt from this

requirement (RTCA/DO-311A

section 1.4.1). This

exemption does not apply

to other battery

configurations".

F3720/F3720M-24 … Standard Practice for None …

General Guidance on

Damage Tolerance

Evaluation of Normal

Category Aeroplane.

F3789-25 … Standard Guide for None …

Endurance Testing of

Aeroplane Flight

Control System

Actuators and Other

System Elements.

\4\ The MOC are intended for traditional part 23 airplanes, not for novel designs. Novel designs require

\4\ The MOC are intended for traditional part 23 airplanes, not for novel designs. Novel designs require

evaluation and possible modification of the MOC. \5\ Wherever "shall" is used within a standard, replace with "must." \6\ You may find additional information on the FAA Small Airplane Issues List (SAIL) here: faa.gov/aircraft/air_cert/design_approvals/small_airplanes/small_airplanes_regs.

Table 2--Side-By-Side View of Part 23 Regulations and ASTM F3264-25

Section(s)

Part 23 amendments 23-64 and ASTM F3264-25 ASTM F3264-25

23-65 regulation(s) section(s) \7\ subsection(s) \8\

Subpart B--Flight

Sec. 23.2100 Weight and 5.1 Weight/Mass 5.1.1 F3082/F3082M-

center of gravity. and Center of 23a Standard

Gravity:. Specification for

Weights and Centers

of Gravity of

Aircraft.

5.1.2 F3114-21

Standard

Specification for

Structures.

Sec. 23.2105 Performance 5.2 Performance 5.2.1 F3179/F3179M-

data. Data:. 24a Standard

Specification for

Performance of

Aircraft. § 23.2110 Stall speed.... 5.3 Stall Speed:. 5.3.1 F3179/F3179M-

24a Standard

Specification for

Performance of

Aircraft.

Sec. 23.2115 Takeoff 5.4 Takeoff 5.4.1 F3179/F3179M-

performance. Performance:. 24a Standard

Specification for

Performance of

Aircraft.

Sec. 23.2120 Climb 5.5 Climb 5.5.1 F3179/F3179M-

requirements. Requirements:. 24a Standard

Specification for

Performance of

Aircraft.

Sec. 23.2125 Climb 5.6 Climb 5.6.1 F3179/F3179M-

information. Information:. 24a Standard

Specification for

Performance of

Aircraft.

Sec. 23.2130 Landing … 5.7 Landing: … 5.7.1 F3179/F3179M-

24a Standard

Specification for

Performance of

Aircraft.

Sec. 23.2135 Controllability 5.8 5.8.1 F3173/F3173M-24

Controllability:. Standard

Specification for

Aircraft Handling

Characteristics.

Sec. 23.2140 Trim … 5.9 Trim: … 5.9.1 F3173/F3173M-24

Standard

Specification for

Aircraft Handling

Characteristics.

Sec. 23.2145 Stability … 5.10 Stability:.. 5.10.1 F3173/F3173M-

24 Standard

Specification for

Aircraft Handling

Characteristics.

Sec. 23.2150 Stall 5.11 Stall 5.11.1 F3180/F3180M-

characteristics, stall Characteristics, 25 Standard

warning, and spins. Stall Warning, Specification for

and Spins:. Low-Speed Flight

Characteristics of

Aircraft.

5.11.1.1 F3454-25

Standard Practice

for Alerting Methods

in Aircraft.

5.11.1.2 F3491-25

Standard Practice

for Enhanced

Indication Methods

in Aircraft.

Sec. 23.2155 Ground and 5.12 Ground and 5.12.1 F3173/F3173M-

water handling Water Handling 24 Standard

characteristics. Characteristics:. Specification for

Aircraft Handling

Characteristics.

Sec. 23.2160 Vibration, 5.13 Vibration, 5.13.1 F3173/F3173M-

buffeting, and high-speed Buffeting, and 24 Standard

characteristics. High-Speed Specification for

Characteristics:. Aircraft Handling

Characteristics. § 23.2165 Performance and 5.14 Performance 5.14.1 F3120/F3120M-

flight characteristics and Flight 24 Standard

requirements for flight in Characteristics Specification for

icing conditions. Requirements for Ice Protection for

Flight in Icing General Aviation

Conditions:. Aircraft.

Subpart C--Structures

Sec. 23.2200 Structural 6.1 Structural 6.1.1 F3116/F3116M-24

design envelope. Design Envelope:. Standard

Specification for

Design Loads and

Conditions.

6.1.1.1 F3396/F3396M-

23a Standard

Practice for

Aircraft Simplified

Loads.

Sec. 23.2205 Interaction of 6.2 Interaction 6.2.1 F3254-22

systems and structures. of Systems and Standard

Structure:. Specification for

Aircraft Interaction

of Systems and

Structures.

Sec. 23.2210 Structural 6.3 Structural 6.3.1 F3116/F3116M-24

design loads. Design Loads:. Standard

Specification for

Design Loads and

Conditions.

6.3.1.1 F3396/F3396M-

23a Standard

Practice for

Aircraft Simplified

Loads.

6.3.2 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2215 Flight load 6.4 Flight Load 6.4.1 F3116/F3116M-24

conditions. Conditions:. Standard

Specification for

Design Loads and

Conditions.

6.4.1.1 F3396/F3396M-

23a Standard

Practice for

Aircraft Simplified

Loads.

Sec. 23.2220 Ground and 6.5 Ground and 6.5.1 F3116/F3116M-24

water load conditions. Water Load Standard

Conditions:. Specification for

Design Loads and

Conditions.

6.5.1.1 F3331-

18(2023) Standard

Practice for

Aircraft Water

Loads.

Sec. 23.2225 Component 6.6 Component 6.6.1 F3061/F3061M-25

loading conditions. Loading Standard

Conditions:. Specification for

Systems and

Equipment in Small

Aircraft.

6.6.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

6.6.2 F3116/F3116M-24

Standard

Specification for

Design Loads and

Conditions.

6.6.2.1 F3396/F3396M-

23a Standard

Practice for

Aircraft Simplified

Loads.

Sec. 23.2230 Limit and 6.7 Limit and 6.7.1 F3114-21

ultimate loads. Ultimate Loads:. Standard

Specification for

Structures.

6.7.1.1 F3601-23

Standard Practice

for Structural

Finite Element Model

Verification and

Validation.

6.7.2 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2235 Structural 6.8 Structural 6.8.1 F3114-21

strength. Strength:. Standard

Specification for

Structures.

6.8.1.1 F3601-23

Standard Practice

for Structural

Finite Element Model

Verification and

Validation.

6.8.2 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2240 Structural 6.9 Structural 6.9.1 F3061/F3061M-25

durability. Durability:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

6.9.2 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

6.9.3 F3115/F3115M-

23e1 Standard

Specification for

Structural

Durability for Small

Aeroplanes.

6.9.3.1 F3380-19

Standard Practice

for Structural

Compliance of Very

Light Aeroplanes.

6.9.3.2 F3498-21

Standard Practice

for Developing

Simplified Fatigue

Load Spectra.

6.9.3.3 F3651/F3651M-

23 Standard Practice

for Determining Safe-

Life, Inspection

Threshold and

Recurring Inspection

Intervals.

6.9.3.4 F3720/F3720M-

24 Standard Practice

for General Guidance

on Damage Tolerance

Evaluation of Normal

Category Aeroplane.

6.9.4 F3116/F3116M-24

Standard

Specification for

Design Loads and

Conditions.

Sec. 23.2245 Aeroelasticity. 6.10 6.10.1 F3093/F3093M-

Aeroelasticity:. 24e1 Standard

Specification for

Aeroelasticity

Requirement.

6.10.2 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

Sec. 23.2250 Design and 6.11 Design and 6.11.1 F3061/F3061M-

construction principles. Construction 25 Standard

Principles:. Specification for

Systems and

Equipment in Small

Aircraft.

6.11.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

6.11.2 F3114-21

Standard

Specification for

Structures.

6.11.2.1 F3380-19

Standard Practice

for Structural

Compliance of Very

Light Aeroplanes.

6.11.3 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2255 Protection of 6.12 Protection 6.12.1 F3061/F3061M-

structure. of Structure:. 25 Standard

Specification for

Systems and

Equipment in Small

Aircraft.

6.12.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

6.12.2 F3114-21

Standard

Specification for

Structures.

6.12.2.1 F3380-19

Standard Practice

for Structural

Compliance of Very

Light Aeroplanes.

6.12.3 F3066/F3066M-

25 Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

6.12.4 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2260 Materials and 6.13 Materials 6.13.1 F3114-21

processes. and Processes:. Standard

Specification for

Structures.

6.13.1.1 F3380-19

Standard Practice

for Structural

Compliance of Very

Light Aeroplanes.

6.13.2 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2265 Special factors 6.14 Special 6.14.1 F3061/F3061M-

of safety. Factors of 25 Standard

Safety:. Specification for

Systems and

Equipment in Small

Aircraft.

6.14.2 F3114-21

Standard

Specification for

Structures.

6.14.2.1 F3380-19

Standard Practice

for Structural

Compliance of Very

Light Aeroplanes.

Sec. 23.2270 Emergency 6.15 Emergency 6.15.1 F3061/F3061M-

conditions. Conditions:. 25 Standard

Specification for

Systems and

Equipment in Small

Aircraft.

6.15.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

6.15.2 F3083/F3083M-

25 Standard

Specification for

Emergency

Conditions, Occupant

Safety and

Accommodations.

6.15.3 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Subpart D--Design and Construction

Sec. 23.2300 Flight control 7.1 Flight 7.1.1 F3061/F3061M-25

systems. Control Systems:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

7.1.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

7.1.2 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

7.1.3 F3117/F3117M-

25a Standard

Specification for

Crew Interface.

Sec. 23.2305 Landing gear 7.2 Landing Gear 7.2.1 F3061/F3061M-25

systems. Systems:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

Sec. 23.2310 Buoyancy for 7.3 Buoyancy for 7.3.1 F3061/F3061M-25

seaplanes and amphibians. Seaplanes and Standard

Amphibians:. Specification for

Systems and

Equipment in Small

Aircraft.

Sec. 23.2315 Means of egress 7.4 Means of 7.4.1 F3061/F3061M-25

and emergency exits. Egress and Standard

Emergency Exits:. Specification for

Systems and

Equipment in Small

Aircraft.

7.4.2 F3083/F3083M-25

Standard

Specification for

Emergency

Conditions, Occupant

Safety and

Accommodations.

Sec. 23.2320 Occupant 7.5 Occupant 7.5.1 F3061/F3061M-25

physical environment. Physical Standard

Environment:. Specification for

Systems and

Equipment in Small

Aircraft.

7.5.1.1 F3227/F3227M-

25 Standard

Specification for

Environmental

Systems in Small

Aircraft.

7.5.2 F3083/F3083M-25

Standard

Specification for

Emergency

Conditions, Occupant

Safety and

Accommodations.

7.5.3 F3114-21

Standard

Specification for

Structures.

7.5.4 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

Sec. 23.2325 Fire protection 7.6 Fire 7.6.1 F3061/F3061M-25

Protection:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

7.6.1.1 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

7.6.1.2 F3234/F3234M-

21(2025) Standard

Specification for

Exterior Lighting in

Small Aircraft.

7.6.1.3 F3316/F3316M-

19 Standard

Specification for

Electrical Systems

for Aircraft with

Electric or Hybrid-

Electric Propulsion.

7.6.2 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

7.6.3 F3083/F3083M-25

Standard

Specification for

Emergency

Conditions, Occupant

Safety and

Accommodations.

7.6.4 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2330 Fire protection 7.7 Fire 7.7.1 F3061/F3061M-25

in designated fire zones and Protection in Standard

adjacent areas. Designated Fire Specification for

Zones and Systems and

Adjacent Areas:. Equipment in Small

Aircraft.

7.7.1.1 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

7.7.2 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

7.7.3 F3114-21

Standard

Specification for

Structures.

Sec. 23.2335 Lightning 7.8 Lightning 7.8.1 F3061/F3061M-25

protection. Protection:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

Subpart E--Powerplant

Sec. 23.2400 Powerplant 8.1 Powerplant 8.1.1 F3062/F3062M-25

installation. Installation:. Standard

Specification for

Aircraft Powerplant

Installation.

8.1.2 F3063/F3063M-24

Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

8.1.3 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.1.3.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.1.4 F3065/F3065M-

21a Standard

Specification for

Aircraft Propeller

System Installation.

8.1.5 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.1.6 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2405 Automatic power 8.2 Power or 8.2.1 F3062/F3062M-25

or thrust control systems. Thrust Control Standard

Systems:. Specification for

Aircraft Powerplant

Installation.

8.2.2 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.2.2.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.2.3 F3065/F3065M-

21a Standard

Specification for

Aircraft Propeller

System Installation.

8.2.4 F3117/F3117M-

25a Standard

Specification for

Crew Interface.

Sec. 23.2410 Powerplant 8.3 Powerplant 8.3.1 F3061/F3061M-25

installation hazard Installation Standard

assessment. Hazard Specification for

Assessment:. Systems and

Equipment in Small

Aircraft.

8.3.2 F3062/F3062M-25

Standard

Specification for

Aircraft Powerplant

Installation.

8.3.3 F3063/F3063M-24

Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

8.3.4 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.3.4.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.3.5 F3065/F3065M-

21a Standard

Specification for

Aircraft Propeller

System Installation.

8.3.6 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.3.7 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

8.3.8 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2415 Powerplant ice 8.4 Powerplant 8.4.1 F3062/F3062M-25

protection. Installation Ice Standard

Protection:. Specification for

Aircraft Powerplant

Installation.

8.4.2 F3063/F3063M-24

Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

8.4.3 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.4.4 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2420 Reversing 8.5 Reversing 8.5.1 F3062/F3062M-25

systems. Systems:. Standard

Specification for

Aircraft Powerplant

Installation.

8.5.2 F3065/F3065M-

21a Standard

Specification for

Aircraft Propeller

System Installation.

8.5.3 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2425 Powerplant 8.6 Powerplant 8.6.1 F3062/F3062M-25

operational characteristics. Operational Standard

Characteristics:. Specification for

Aircraft Powerplant

Installation.

8.6.2 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.6.2.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.6.3 F3065/F3065M-

21a Standard

Specification for

Aircraft Propeller

System Installation.

8.6.4 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.6.5 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

8.6.6 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2430 Fuel systems... 8.7 Fuel and 8.7.1 F3062/F3062M-25

Energy Storage Standard

and Distribution Specification for

Systems:. Aircraft Powerplant

Installation.

8.7.2 F3063/F3063M-24

Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

8.7.2.1 F3397/F3397M-

21 Standard Practice

for Aeroplane

Turbine Fuel System

Hot Weather

Operations.

8.7.3 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.7.3.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.7.4 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.7.5 F3114-21

Standard

Specification for

Structures.

8.7.6 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2435 Powerplant 8.8 Powerplant 8.8.1 F3062/F3062M-25

induction and exhaust systems. Induction, Standard

Exhaust, and Specification for

Support Systems:. Aircraft Powerplant

Installation.

8.8.2 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Sec. 23.2440 Powerplant fire 8.9 Powerplant 8.9.1 F3061/F3061M-25

protection. Installation Standard

Fire Protection:. Specification for

Systems and

Equipment in Small

Aircraft.

8.9.2 F3062/F3062M-25

Standard

Specification for

Aircraft Powerplant

Installation.

8.9.3 F3063/F3063M-24

Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

8.9.4 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

8.9.4.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

8.9.5 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

8.9.6 F3239-22a

Standard

Specification for

Aircraft Electric

Propulsion Systems.

Subpart F--Equipment

Sec. 23.2500 Airplane level 9.1 Systems and 9.1.1 F3061/F3061M-25

systems requirements. Equipment Standard

Function--Requir Specification for

ements:. Systems and

Equipment in Small

Aircraft.

9.1.1.1 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

9.1.1.1(a) F3235-22

Standard

Specification for

Aircraft Storage

Batteries.

9.1.1.2 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

9.1.1.3 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.1.1.3(a) F3229/

F3229M-23a Standard

Practice for Static

Pressure System

Tests in Small

Aircraft.

9.1.1.4 F3316/F3316M-

19 Standard

Specification for

Electrical Systems

for Aircraft with

Electric or Hybrid-

Electric Propulsion.

9.1.1.5 F3789-25

Standard Guide for

Endurance Testing of

Aeroplane Flight

Control System

Actuators and Other

System Elements.

9.1.2 F3064/F3064M-24

Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

9.1.2.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

9.1.3 F3066/F3066M-25

Standard

Specification for

Aircraft Powerplant

Installation Hazard

Mitigation.

9.1.4 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

9.1.5 F3120/F3120M-24

Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

9.1.6 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2505 Function and 9.2 Equipment 9.2.1 F3061/F3061M-25

installation. Function and Standard

Installation Specification for

Requirements:. Systems and

Equipment in Small

Aircraft.

9.2.1.1 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

9.2.1.1(a) F3235-22

Standard

Specification for

Aircraft Storage

Batteries.

9.2.1.2 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

9.2.1.3 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.2.1.4 F3316/F3316M-

19 Standard

Specification for

Electrical Systems

for Aircraft with

Electric or Hybrid-

Electric Propulsion.

9.2.1.4(a) F3653-24

Standard

Specification for

Installation of

Rechargeable Lithium

Batteries on

Aircraft.

9.2.2 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

9.2.3 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

Sec. 23.2510 Equipment, 9.3 Equipment, 9.3.1 F3061/F3061M-25

systems, and installations. Systems, and Standard

Installation:. Specification for

Systems and

Equipment in Small

Aircraft.

9.3.1.1 F3230-25

Standard Practice

for Safety

Assessments of

Systems and

Equipment in Small

Aircraft.

9.3.1.2 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.3.1.3 F3227/F3227M-

25 Standard

Specification for

Environmental

Systems in Small

Aircraft.

9.3.1.4 F3309/F3309M-

24a Standard

Practice for

Simplified Safety

Assessment of

Systems and

Equipment in Small

Aircraft.

9.3.1.5 F3532-25

Standard Practice

for Protection of

Aircraft Systems

from Intentional

Unauthorized

Electronic

Interactions.

9.3.2 F3408/F3408M-21

Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2515 Electrical and 9.4 Electrical 9.4.1 F3061/F3061M-25

electronic system lightning and Electronic Standard

protection. System Lightning Specification for

Protection:. Systems and

Equipment in Small

Aircraft.

9.4.1.1 F3367-23

Standard Practice

for Simplified

Methods for

Addressing High-

Intensity Radiated

Fields (HIRF) and

Indirect Effects of

Lightning on

Aircraft.

Sec. 23.2520 High-intensity 9.5 High 9.5.1 F3061/F3061M-25

Radiated Fields (HIRF) Intensity Standard

protection. Radiated Fields Specification for

(HIRF) Systems and

Protection:. Equipment in Small

Aircraft.

9.5.1.1 F3236-21a

Standard

Specification for

High Intensity

Radiated Field

(HIRF) Protection in

Small Aircraft.

9.5.1.2 F3367-23

Standard Practice

for Simplified

Methods for

Addressing High-

Intensity Radiated

Fields (HIRF) and

Indirect Effects of

Lightning on

Aircraft.

Sec. 23.2525 System power 9.6 System Power 9.6.1 F3061/F3061M-25

generation, storage, and Generation, Standard

distribution. Storage, and Specification for

Distribution:. Systems and

Equipment in Small

Aircraft.

9.6.1.1 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

9.6.1.1(a) F2490-20

Standard Guide for

Aircraft Electrical

Load and Power

Source Capacity

Analysis.

9.6.1.2 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.6.1.3 F3316/F3316M-

19 Standard

Specification for

Electrical Systems

for Aircraft with

Electric or Hybrid-

Electric Propulsion.

9.6.1.3(a) F2490-20

Standard Guide for

Aircraft Electrical

Load and Power

Source Capacity

Analysis.

9.6.1.3(b) F3653-24

Standard

Specification for

Installation of

Rechargeable Lithium

Batteries on

Aircraft.

9.6.2 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

9.6.3 F3120/F3120M-24

Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

Sec. 23.2530 External and 9.7 External and 9.7.1 F3061/F3061M-25

cockpit lighting. Cockpit Standard

Lighting:. Specification for

Systems and

Equipment in Small

Aircraft.

9.7.1.1 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.7.1.2 F3234/F3234M-

21(2025) Standard

Specification for

Exterior Lighting in

Small Aircraft.

9.7.2 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

9.7.3 F3120/F3120M-24

Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

Sec. 23.2535 Safety 9.8 Safety 9.8.1 F3061/F3061M-25

equipment. Equipment:. Standard

Specification for

Systems and

Equipment in Small

Aircraft.

9.8.2 F3083/F3083M-25

Standard

Specification for

Emergency

Conditions, Occupant

Safety and

Accommodations.

9.8.3 F3117/F3117M-

25a Standard

Specification for

Crew Interface.

Sec. 23.2540 Flight in icing 9.9 Flight in 9.9.1 F3061/F3061M-25

conditions. Icing Standard

Conditions:. Specification for

Systems and

Equipment in Small

Aircraft.

9.9.1.1 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

9.9.2 F3120/F3120M-24

Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

Sec. 23.2545 Pressurized 9.10 Pressurized 9.10.1 F3061/F3061M-

systems elements. System Elements:. 25 Standard

Specification for

Systems and

Equipment in Small

Aircraft.

9.10.1.1 F3229/F3229M-

23a Standard

Practice for Static

Pressure System

Tests in Small

Aircraft.

Sec. 23.2550 Equipment 9.11 Equipment 9.11.1 F3061/F3061M-

containing high-energy rotors. Containing High- 25 Standard

containing high-energy rotors. Containing High- 25 Standard

Energy Rotors:. Specification for

Systems and

Equipment in Small

Aircraft.

Subpart G--Flight Crew Interface and Other Information

Sec. 23.2600 Flightcrew 10.1 Flight crew 10.1.1 F3061/F3061M-

interface. Compartment 25 Standard

Interface:. Specification for

Systems and

Equipment in Small

Aircraft.

10.1.1.1 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

10.1.2 F3062/F3062M-

25 Standard

Specification for

Aircraft Powerplant

Installation.

10.1.3 F3063/F3063M-

24 Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

10.1.4 F3064/F3064M-

24 Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

10.1.4.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

10.1.5 F3114-21

Standard

Specification for

Structures.

10.1.6 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

10.1.6.1 F3643-25

Standard Practice

for Pilot

Compartment View in

Precipitation.

10.1.7 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2605 Installation 10.2 Installation 10.2.1 F3061/F3061M-

and operation. and Operation 25 Standard

Information:. Specification for

Systems and

Equipment in Small

Aircraft.

10.2.1.1 F3227/F3227M-

25 Standard

Specification for

Environmental

Systems in Small

Aircraft.

10.2.1.2 F3231/F3231M-

24 Standard

Specification for

Electrical Systems

for Aircraft with

Combustion Engine

Electrical Power

Generation.

10.2.1.3 F3232/F3232M-

25a Standard

Specification for

Flight Controls in

Small Aircraft.

10.2.1.4 F3233/F3233M-

23b Standard

Specification for

Flight and

Navigation

Instrumentation in

Aircraft.

10.2.2 F3062/F3062M-

25 Standard

Specification for

Aircraft Powerplant

Installation.

10.2.3 F3063/F3063M-

24 Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

10.2.4 F3064/F3064M-

24 Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

10.2.4.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

10.2.5 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

10.2.6 F3120/F3120M-

24 Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

10.2.7 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2610 Instrument 10.3 Instrument 10.3.1 F3061/F3061M-

markings, control markings, Markings, 25 Standard

and placards. Control Specification for

Markings, and Systems and

Placards:. Equipment in Small

Aircraft.

10.3.2 F3063/F3063M-

24 Standard

Specification for

Aircraft Fuel and

Energy Storage and

Delivery.

10.3.3 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

10.3.4 F3120/F3120M-

24 Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

10.3.5 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

Sec. 23.2615 Flight, 10.4 Flight, 10.4.1 F3061/F3061M-

navigation, and powerplant Navigation, and 25 Standard

instruments. Powerplant Specification for

Instruments:. Systems and

Equipment in Small

Aircraft.

10.4.2 F3062/F3062M-

25 Standard

Specification for

Aircraft Powerplant

Installation.

10.4.3 F3064/F3064M-

24 Standard

Specification for

Aircraft Powerplant

Control, Operation,

and Indication.

10.4.3.1 F3432-20a

Standard Practice

for Powerplant

Instruments.

10.4.4 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

10.4.4.1 F3454-25

Standard Practice

for Alerting Methods

in Aircraft.

10.4.4.2 F3491-25

Standard Practice

for Enhanced

Indication Methods

in Aircraft.

Sec. 23.2620 Airplane flight 5.15 Operating 5.15.1 F3174/F3174M-

manual. Limitations:. 21 Standard

10.5 Airplane Specification for

Flight Manual:. Establishing

Operating

Limitations and

Information for

Aeroplanes.

5.15.2 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

10.5.1 F3117/F3117M-

25a Standard

Specification for

Crew Interface in

Aircraft.

10.5.2 F3174/F3174M-

21 Standard

Specification for

Establishing

Operating

Limitations and

Information for

Aeroplanes.

10.5.3 F3120/F3120M-

24 Standard

Specification for

Ice Protection for

General Aviation

Aircraft.

10.5.4 F3408/F3408M-

21 Standard

Specification for

Aircraft Emergency

Parachute Recovery

Systems.

\7\ The ASTM F3264-25 section(s) provides a means of compliance intended

\7\ The ASTM F3264-25 section(s) provides a means of compliance intended

to be used on projects for traditional part 23 airplanes, not for

novel designs. Novel designs require evaluation and possible

modification of the means of compliance. \8\ Changes required for FAA acceptance and additional information per

Table 1 still apply to Table 2. The FAA does not accept the Aircraft

Type Code compliance matrix tables included in F3228-21(2025), F3229/

F3229M-23a, F3231/F3231M-24, F3233/F3233M-23b, F3234/F3234M-21(2025),

F3235-22, F3236-21a, and F3316/F3316M-19. The tables defining

applicability found in F3061/F3061M--25 sections 4.1.6, 4.2.3.3,

4.2.6, 4.2.8, 4.2.8.1, 4.2.8.2, 4.3.1, 4.3.2.1, 4.3.2.2, 4.4, 10.1,

10.1.1, 10.1.2, 10.1.3, 10.1.4, 10.3.3, 10.3.4, 10.3.5, 10.3.6,

10.3.7, 10.3.8, 10.3.9, 10.4.2, 10.4.3, 10.4.4, 10.7.1, 10.7.2,

10.7.3, 10.7.4, 10.7.5, 10.7.6, 10.7.7, 10.7.7.1, 10.8, 13.1.1,

13.1.2, 17.1.1, 17.1.2, 17.1.3, 17.2.1, 17.2.2, 17.2.3, 17.3.1.1,

17.3.1.2, 17.3.1.3, 17.3.1.4, and 18.4 are not accepted. Applicability

will be determined by the Policy and Standards Division.

The MOC accepted by this NOA provides one means, but not the only means, of complying with part 23 regulatory requirements. Applicants who desire to use a MOC reflected by other revisions to ASTM standards not previously accepted may seek guidance and possible acceptance from the FAA for the use of those MOC on a case-by-case basis. Applicants may propose an alternative MOC for FAA review and possible acceptance.

Editorial, Reapproval, Revision, or Withdrawal

Editorial, Reapproval, Revision, or Withdrawal

ASTM policy states that a consensus standard should be reviewed in its entirety by the responsible subcommittee and must be balloted for reapproval, revision, or withdrawal within five years of its last approval date. When an ASTM standard is reapproved, that reapproval is denoted by the year in parentheses (e.g., F2427-05a (2013)). This date indicates the completion of a review cycle with no technical changes made to the standard. In addition, ASTM issues editorial changes denoted by a superscript epsilon in the standard designation (e.g., F3235-17[epsi]1). This epsilon indicates information was corrected, and it did not change the meaning or intent of a standard. Since reapprovals and editorial changes do not change the technical content of standards, any standard FAA-accepted by this NOA that is later reapproved or editorially changed by ASTM is also considered FAA-accepted without the need for an updated NOA.

ASTM revises a standard to make changes to its technical content. Revisions are identified by a hyphen after the document number, which is followed by the last two numbers of the year of acceptance or of last revision. If the standard is revised again during the same year, this is indicated by adding an "a" for the second revision, "b" for the third revision, and so on for each revision. Since revisions change the technical content, revisions to consensus standards that are the basis for a MOC accepted by this NOA will not be automatically accepted and will require further FAA acceptance for the revisions to be an accepted MOC.

Availability

Availability

ASTM F3264-25, "Standard Specification for Normal Category Aeroplanes Certification," is available online at astm.org/readinglibrary. ASTM copyrights these consensus standards and charges the public a fee for service. Individual downloads or reprints of a standard (single or multiple copies, special compilations, and other related technical information), as well as information regarding membership, ASTM offices abroad, or Committee F44 on General Aviation Aircraft, may be obtained online or by contacting ASTM by telephone: (610) 832-9585; facsimile: (610) 832-9555; or through email: [email protected].

Issued in Fort Worth, Texas, on November 4, 2026. James Blyn, Acting Manager, General Aviation, VTOL & Engine Standards Branch, Certification Standards Division, Aircraft Certification Service.