Radar Vectors
Final Rule Current Issued Sep 22, 2020 5 pages Copy saved Nov 17, 2026

85 FR 59400 Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

This document announces the availability of means of compliance to the applicable airworthiness standards for normal category airplanes. The Administrator finds these means of compliance to be an acceptable means, but not the only means, of showing compliance to the applicable airworthiness standards for normal category airplanes and that they provide an appropriate level of safety.

Official source ↗ Official PDF ↗

14 CFR Part 23

[Docket No. FAA-2020-0798; Notice No. 23-20-01-NOA]

Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

AGENCY: Federal Aviation Administration, DOT

ACTION: Notification of availability.

SUMMARY: This document announces the availability of means of compliance to the applicable airworthiness standards for normal category airplanes. The Administrator finds these means of compliance to be an acceptable means, but not the only means, of showing compliance to the applicable airworthiness standards for normal category airplanes and that they provide an appropriate level of safety.

Dates

DATES: Effective September 22, 2020.

FOR FURTHER INFORMATION CONTACT: Andy Supinie, Federal Aviation Administration, Policy and Innovation Division, Small Airplane Standards Branch, AIR-690, 901 Locust Street, Room 301, Kansas City, Missouri 64106; telephone (316) 946-4150; facsimile: (316) 946-4107; email: [email protected].

Supplementary Information

SUPPLEMENTARY INFORMATION: Background: Under the provisions of the National Technology Transfer and Advancement Act of 1995 \1\ and Office of Management and Budget (OMB) Circular A-119, "Federal Participation in the Development and Use of Voluntary Consensus Standards and in Conformity Assessment Activities," effective January 27, 2016, the FAA participates in the development of consensus standards and uses consensus standards as a means of carrying out its policy objectives where appropriate.

\1\ Ref Public Law 104-113 as amended by Public Law 107-107.

Consistent with the Small Airplane Revitalization Act of 2013,\2\ the FAA has been working with industry and other stakeholders lop consensus standards for use as a means of compliance in certificating small airplanes under Title 14, Code of Federal Regulations (14 CFR) part 23. In promulgating part 23, amendment 23-64 \3\ (81 FR 96572, December 30, 2016), the FAA explained that if it determined such consensus standards were acceptable means of compliance to part 23, it would publish a notice of availability of those consensus standards in the Federal Register.

\2\ Ref Public Law 113-53.

\3\ See https://www.federalregister.gov/documents/2016/12/30/2016-30246/revision-of-airworthiness-standards-for-normal-utility-acrobatic-and-commuter-category-airplanes.

Pursuant to FAA Advisory Circular 23.2010-1,\4\ "FAA Accepted Means of Compliance Process for 14 CFR part 23," section 3.1.1, this notice serves as a formal acceptance by the Administrator of means of compliance based on consensus standards developed by ASTM. The means of compliance accepted by this notice are one means, but not the only means of complying with part 23 regulatory requirements.

\4\ See https://rgl.faa.gov/.

The FAA reviewed 35 published ASTM consensus standards, developed by ASTM Committee F44, as the basis for means of compliance to 65 sections of part 23, amendment 23-64. In some cases, the Administrator finds sections of ASTM Standard F3264-19, "Standard Specification for Normal Category Aeroplanes Certification," without changes, are accepted as means of complying with the airworthiness requirements of amendment 23-64, within the scope and applicability of the consensus standards. In other cases, the means of compliance, while based on ASTM consensus standards, include additional FAA provisions necessary to comply with the airworthiness requirements of amendment 23-64.

This document accepts only the revisions of standards referenced in ASTM Standard F3264-19, "Standard Specification for Normal Category Aeroplanes Certification." Applicants who desire to use means of compliance reflected by other revisions to ASTM standards not previously accepted may seek guidance and possible acceptance from FAA for the use of those means of compliance on a case-by-case basis. Applicants may also propose alternative means of compliance for FAA review and possible acceptance.

Amendment 23-64 established airworthiness requirements based on the level of safety of amendment 23-63 regulations, except for areas addressing loss of control and icing where the safety level was increased. Achieving this level of safety through compliance with amendment 23-64--for a given certification project--may require use of additional means of compliance beyond those accepted by this notice, depending on the details of the specific design. For example, applicants with novel designs, such as unmanned airplanes or vertical takeoff and landing airplanes that are outside the scope and applicability of these consensus standards must propose alternative means of compliance, applicable to their designs, to be accepted under § 23.2010.

Further information on supplemental means of compliance is provided in a part 23 means of compliance summary table and in the Small Airplanes Issues List, which are available on the Small Airplanes--Regulations, Policies & Guidance website.\5\

\5\ See https://www.faa.gov/aircraft/air_cert/design_approvals/small_airplanes/small_airplanes_regs/.

Means of Compliance Accepted in this Policy: The following is a list of part 23, amendment 23-64, sections followed by their corresponding means of compliance accepted by this notice. However, for means of compliance identified in the following list, Aircraft Type Code compliance matrix tables, which define applicability of the individual requirements of given standards, are not accepted in any ASTM F44 standard. Due to errors identified in the Aircraft Type Code compliance matrix tables, applicability of individual requirements of standards must be established with the Small Airplane Standards Branch.

23.1457: ASTM F3264-19, section 9.12 23.1459: ASTM F3264-19, section 9.13 23.1529: ASTM F3264-19, section 10.6

23.1457: ASTM F3264-19, section 9.12 23.1459: ASTM F3264-19, section 9.13 23.1529: ASTM F3264-19, section 10.6

Subpart B--Flight

23.2100: ASTM F3264-19, section 5.1 23.2105: ASTM F3264-19, section 5.2 23.2110: ASTM F3264-19, section 5.3 23.2115: ASTM F3264-19, section 5.4 23.2120: ASTM F3264-19, section 5.5 23.2125: ASTM F3264-19, section 5.6 23.2130: ASTM F3264-19, section 5.7 23.2135: ASTM F3264-19, section 5.8, combined with the changes in the following table:

Subpart B--Flight

Replace: With:

ASTM F3173/F3173M-18, Section FAA Section 4.3.2

4.3.2. "Unless otherwise required, it shall be

possible to carry out the following

maneuvers without requiring the

application of temporary one-hand

control forces exceeding those specified

in Table 1, appropriate for the type of

ASTM F3173/F3173M-18, Section FAA Section 4.3.2

control. The trimming controls shall not

be adjusted during the maneuvers." ASTM F3173/F3173M-18, Section FAA Section 4.3.2.3

4.3.2.3. "With landing gear and flaps extended,

power necessary to maintain level flight

at 1.1 VS0, and the airplane as nearly

as possible in trim, it shall be

possible to maintain approximately level

flight while retracting the flaps as

rapidly as possible with simultaneous

application of maximum continuous power.

If the level acceleration will result in

exceeding VFE of the initial flap

configuration prior to the flaps

reaching their selected setting, power

may be reduced after achieving 1.3 VFE

of the initial flap configuration. The

maneuver continues until the flaps reach

the selected setting and the airplane

achieves VFE of the initial flap

configuration. If gated flap positions

are provided, the flap retraction may be

demonstrated in stages with power and

trim reset for level flight at 1.1 VS1,

in the initial configuration for each

stage:

(1) From the fully extended position to

the most extended gated position;

(2) Between intermediate gated positions,

if applicable; and

(3) From the least extended gated

position to the fully retracted

position." ASTM F3173/F3173M-18, Section FAA Section 4.7

4.7. "It shall be possible, while in the

landing configuration, to complete a

landing without causing substantial

damage or serious injury, and without

exceeding the temporary one-hand control

force limits specified in Table 1,

appropriate for the type of control,

following an approach to land under the

following conditions;" ASTM F3173/F3173M-18 Section FAA Section 5.3.1.3

5.3.1.3. "In a descent with idle power at a speed

of 1.3 VS0 with landing gear extended

and wing flaps in the landing

position." ASTM F3173/F3173M-18 Section FAA Section 9.3.4

9.3.4. "If the procedure set forth in 9.3.3.2

is used to demonstrate compliance and

marginal conditions existing during

flight test with regard to reversal of

primary longitudinal control force,

flight tests shall be accomplished from

the normal acceleration at which a

marginal stick force per g condition is

found to exist to the applicable limit

specified in 9.3.2.1."

23.2140: ASTM F3264-19, section 5.9 23.2145: ASTM F3264-19, section 5.10 23.2150: ASTM F3264-19, section 5.11, after replacing ASTM F3180/ F3180M-19 with ASTM F3180/F3180M-16 23.2155: ASTM F3264-19, section 5.12 23.2160: ASTM F3264-19, section 5.13 23.2165: ASTM F3264-19, section 5.14

Subpart C--Structures

Subpart C--Structures

23.2200: ASTM F3264-19, section 6.1 23.2205: ASTM F3264-19, section 6.2, combined with the changes to ASTM F3254-19, Figures 2, 3, and 4 shown in the following table:

Replace: With:

"Remote" … "10-5"

"Extremely Improbable" … "10-8" for Level 1, 2 and 3 airplanes

"Extremely Improbable" … "10-8" for Level 1, 2 and 3 airplanes

and with "10-9" for Level 4

airplanes"

23.2210: ASTM F3264-19, section 6.3 23.2215: ASTM F3264-19, section 6.4, combined with the changes in the following table:

Replace: With:

ASTM F3116/F3116M-18, Section FAA Section 4.1.4

4.1.4. "Appendix X1 through Appendix X4

provides, within the limitations

ASTM F3116/F3116M-18, Section FAA Section 4.1.4

specified within the appendix, a

simplified means of compliance with

several of the requirements set forth in

sections 4.2 to 4.26 and 7.1 to 7.9 that

can be applied as one (but not the only)

means to comply. If the simplified

methods in appendix X1 through X3 are

used, they must be used together in

their entirety." ASTM F3116/F3116M-18, Section FAA Section X1.1.1

X1.1.1. "The methods provided in this appendix

provide one possible means (but not the

only possible means) of compliance and

can only be applied to level 1 and level

2 low speed airplanes."

23.2220: ASTM F3264-19, section 6.5 23.2225: ASTM F3264-19, section 6.6, combined with the changes in the following table:

Replace: With:

ASTM F3116/F3116M-18, Section FAA X2.1.1

ASTM F3116/F3116M-18, Section FAA X2.1.1

X2.1.1. "The methods provided in this appendix

provide one possible means (but not the

only possible means) of compliance and

can only be applied to level 1 and level

2 low speed airplanes." ASTM F3116/F3116M-18, Section FAA X3.1.1

X3.1.1. "The methods provided in this appendix

provide one possible means (but not the

only possible means) of compliance and

can only be applied to level 1 and level

2 low speed airplanes." ASTM F3116/F3116M-18, Section FAA X4.1.1

X4.1.1. "The methods provided in this appendix

provide one possible means (but not the

only possible means) of compliance and

can only be applied to level 1 low speed

airplanes."

23.2230: ASTM F3264-19, section 6.7 23.2235: ASTM F3264-19, section 6.8 23.2240: ASTM F3264-19, section 6.9, after replacing ASTM F3115/F3115M-19 with ASTM F3115/F3115M-15 and making the changes in the following table:

Replace: With:

ASTM F3115/F3115M-15, Section FAA 4.4.1

ASTM F3115/F3115M-15, Section FAA 4.4.1

4.4.1. "For metallic (aluminum), unpressurized,

non-aerobatic, low-speed, level 1

airplanes, applicants can demonstrate a

10,000 hour safe-life by limiting the

`1g' gross stress, at maximum takeoff

weight, to no more than 5.5 ksi. The

applicant must show effective stress

concentration factors of 4 or less in

highly loaded joints and use materials

or material systems for which the

physical and mechanical properties are

well established." ASTM F3115/F3115M-15, Section FAA 6.1

6.1. "For bonded airframe structure, the

residual strength of bonded joints shall

be addressed as follows: For any bonded

joint, the failure of which would result

in catastrophic loss of the airplane,

the limit load capacity must be

substantiated by one of the following

methods."

23.2245: ASTM F3264-19, section 6.10 23.2250: ASTM F3264-19, section 6.11 23.2255: ASTM F3264-19, section 6.12 23.2260: ASTM F3264-19, section 6.13 23.2265: ASTM F3264-19, section 6.14 23.2270: ASTM F3264-19, section 6.15, combined with the changes in the following table:

Replace: With:

ASTM F3083/F3083M-19 Section FAA Section 4.1.6

ASTM F3083/F3083M-19 Section FAA Section 4.1.6

4.1.6. "Engine mount and supporting structure

must withstand 18.0 g forward for

engines installed behind and above the

seating compartment."

Subpart D--Design and Construction

23.2300: ASTM F3264-19, section 7.1 23.2305: ASTM F3264-19, section 7.2 23.2310: ASTM F3264-19, section 7.3 23.2315: ASTM F3264-19, section 7.4 23.2320: ASTM F3264-19, section 7.5 23.2325: ASTM F3264-19, section 7.6, except delete ASTM F3264-19, section 7.6.1.3 23.2330: ASTM F3264-19, section 7.7 23.2335: ASTM F3264-19, section 7.8

Subpart E--Powerplant

Subpart E--Powerplant

23.2400: ASTM F3264-19, section 8.1, except delete ASTM F3264-19, section 8.1.6 23.2405: ASTM F3264-19, section 8.2, except delete ASTM F3264-19, section 8.2.4 23.2410: ASTM F3264-19, section 8.3, except delete ASTM F3264-19, section 8.3.8 23.2415: ASTM F3264-19, section 8.4, combined with the following changes:

1. Delete ASTM F3264-19, section 8.4.4

2. Add: An FAA accepted means of compliance for the turbine engine installation ice protection requirement of § 23.2415, on airplanes not approved for flight into known icing, such as the provisions of F3120/F3120M-19 section 7.2 and 7.3 (regardless of the operation requirements in F3120/F3120M-19 Table 1). 23.2420: ASTM F3264-19, section 8.5, except delete ASTM F3264-19, section 8.5.3 23.2425: ASTM F3264-19, section 8.6, except delete ASTM F3264-19, section 8.6.6 23.2430: ASTM F3264-19, section 8.7, except delete ASTM F3264-19, section 8.7.6 23.2435: ASTM F3264-19, section 8.8, except delete ASTM F3264-19, section 8.8.2 23.2440: ASTM F3264-19, section 8.9, except delete ASTM F3264-19, section 8.9.5

Subpart F--Equipment

Subpart F--Equipment

23.2500: ASTM F3264-19, section 9.1, combined with the following changes:

1. Delete ASTM F3264-19, section 9.1.1.2(a)

2. Delete ASTM F3264-19, section 9.1.1.5

3. As shown in the following table:

Replace: With:

ASTM F3230-17 Section 3.2.1.. FAA Section 3.2.1

"aircraft type code, n--an Aircraft Type

ASTM F3230-17 Section 3.2.1.. FAA Section 3.2.1

Code (ATC) is defined by considering

both the technical considerations

regarding the design of the aircraft and

the aeroplane certification level

established based upon risk-based

criteria; the method of defining an ATC

applicable to this practice is defined

in Specification F3061/F3061M."

ASTM F3230-17 Section 4 FAA Section 4 Example

Example. "Example--An aircraft with an ATC of

1SRLLDLN is being considered. Since all

applicable columns are empty for 4.1,

that subsection is applicable to the

aircraft. Since the "1" aeroplane

certification level column, the "L"

stall speed column, and the "D"

meteorological column for 4.2.1 all

contain white circles, then that

subsection is not applicable; however,

for an aircraft with an ATC of 1SRMLDLN,

4.2.1 would be applicable since the

"M" stall speed column does not

contain a white circle."

ASTM F3230-17 Table 1 … FAA Table 1

Column header "Airworthiness Column header "Aeroplane Certification

Column header "Airworthiness Column header "Aeroplane Certification

Level". Level".

ASTM F3230-17 Table 3 … FAA Table 3

Column header "Airworthiness Column header "Aeroplane Certification

Level". Level".

23.2505: ASTM F3264-19, section 9.2, combined with the following changes:

1. Delete ASTM F3264-19, section 9.2.1.1(a)

2. Delete ASTM F3264-19, section 9.2.1.4 23.2510: ASTM F3264-19, section 9.3, combined with the following changes:

1. Delete ASTM F3264-19, section 9.3.1.2

2. As shown in the following table:

Replace: With:

ASTM F3230-17 Section 3.2.1.. FAA Section 3.2.1

ASTM F3230-17 Section 3.2.1.. FAA Section 3.2.1

"aircraft type code, n--an Aircraft Type

Code (ATC) is defined by considering

both the technical considerations

regarding the design of the aircraft and

the aeroplane certification level

established based upon risk-based

criteria; the method of defining an ATC

applicable to this practice is defined

in Specification F3061/F3061M."

ASTM F3230-17 Section 4 FAA Section 4 Example

Example. "Example--An aircraft with an ATC of

1SRLLDLN is being considered. Since all

applicable columns are empty for 4.1,

that subsection is applicable to the

aircraft. Since the "1" aeroplane

certification level column, the "L"

stall speed column, and the "D"

meteorological column for 4.2.1 all

contain white circles, then that

subsection is not applicable; however,

for an aircraft with an ATC of 1SRMLDLN,

4.2.1 would be applicable since the

"M" stall speed column does not

contain a white circle."

ASTM F3230-17 Table 1 … FAA Table 1

Column header "Airworthiness Column header "Aeroplane Certification

Column header "Airworthiness Column header "Aeroplane Certification

Level". Level"

ASTM F3230-17 Table 3 … FAA Table 3

Column header "Airworthiness Column header "Aeroplane Certification

Level". Level"

23.2515: ASTM F3264-19, section 9.4 23.2520: ASTM F3264-19, section 9.5, combined with the changes in the following table:

Replace: With:

ASTM F3236-17 Table 2 entry.. FAA Table 2 entry

ASTM F3236-17 Table 2 entry.. FAA Table 2 entry

400 to 700 Mhz frequency 400 to 700 Mhz frequency range field

range field strength average strength average value: value: "100 volts/meter". "50 volts/meter" ASTM F3236-17 Section 4.2.3.3 FAA Section 4.2.3.3

"From 40 to 400 MHz, use conducted

range field strength average strength average value: value: "100 volts/meter". "50 volts/meter" ASTM F3236-17 Section 4.2.3.3 FAA Section 4.2.3.3

susceptibility tests, starting at a

minimum of 30 mA at 40 MHz, decreasing

20 dB per frequency decade to a minimum

of 3 mA at 400 MHz."

23.2525: ASTM F3264-19, section 9.6, except delete ASTM F3264-19, section 9.6.2.3 23.2530: ASTM F3264-19, section 9.7 23.2535: ASTM F3264-19, section 9.8, except delete ASTM F3264-19, section 9.8.1 23.2540: ASTM F3264-19, section 9.9 23.2545: ASTM F3264-19, section 9.10 23.2550: ASTM F3264-19, section 9.11

Subpart G--Flightcrew Interface and Other Information

Subpart G--Flightcrew Interface and Other Information

23.2600: ASTM F3264-19, section 10.1, combined with the following changes:

1. Add an FAA-accepted means of compliance for the windshield luminous transmittance aspects of § 23.2600, such as the provisions of § 23.775(e), amendment 23-49.

2. Add an FAA-accepted means of compliance for the pilot compartment view with formation of fog or frost aspects of § 23.2600, such as the provisions of § 23.773(b), amendment 23-45. 23.2605: ASTM F3264-19, section 10.2 23.2610: ASTM F3264-19, section 10.3 23.2615: ASTM F3264-19, section 10.4, combined with the changes in the following table:

Replace: With:

ASTM F3064/F3064M-19, Section 6... An FAA-accepted means of compliance

ASTM F3064/F3064M-19, Section 6... An FAA-accepted means of compliance

for the powerplant instruments

aspects of § 23.2615, such as

the provisions of § 23.1305,

amendment 23-52.

23.2620: ASTM F3264-19, sections 5.15 AND 10.5

Editorial, reapproval, revision or withdrawal: The FAA expects a suitable consensus standard to be reviewed periodically. ASTM policy is that a consensus standard should be reviewed in its entirety by the responsible subcommittee and must be balloted for reapproval, revision, or withdrawal, within five years of its last approval date. ASTM reapproves a standard--denoted by the year of reapproval in parentheses (e.g., F2427-05a(2013))--to indicate completion of a review cycle with no technical changes made to the standard. ASTM issues editorial changes--denoted by a superscript epsilon in the standard designation (e.g., F3235-17[epsi]1)--to correct information that does not change the meaning or intent of a standard. Any means of compliance accepted by this notice that is based on a standard later reapproved or editorially changed is also considered accepted without the need for a NOA. ASTM revises a standard to make changes to its technical content. Revisions to consensus standards serving as the basis for means of compliance accepted by this notice will not be automatically accepted and will require further FAA acceptance in order for the revisions to be an accepted means of compliance.

Availability

Availability

ASTM Standard F3264-19, "Standard Specification for Normal Category Aeroplanes Certification," is available for online reading at https://www.astm.org/READINGLIBRARY/. ASTM International copyrights these consensus standards and charges the public a fee for service. Individual downloads or reprints of a standard (single or multiple copies, or special compilations and other related technical information) may be obtained through www.astm.org or contacting ASTM at (610) 832-9585 (phone), (610) 832-9555 (fax), or through [email protected] (email). To inquire about consensus standard content and/or membership or about ASTM Offices abroad, contact Joe Koury, Staff Manager for Committee F44 on General Aviation Aircraft: (610) 832-9804, [email protected].

The FAA maintains a list of accepted means of compliance on the FAA website at https://www.faa.gov/aircraft/air_cert/design_approvals/small_airplanes/small_airplanes_regs/.

Issued in Kansas City, Missouri on August 12, 2020. Pat Mullen, Manager, Small Airplanes Standards Branch, Policy and Innovation Division, Aircraft Certification Service.