Radar Vectors
Proposed Rule Proposed Issued Dec 31, 2019 87 pages Copy saved Nov 17, 2026

84 FR 72438 Remote Identification of Unmanned Aircraft Systems

This action would require the remote identification of unmanned aircraft systems. The remote identification of unmanned aircraft systems in the airspace of the United States would address safety, national security, and law enforcement concerns regarding the further integration of these aircraft into the airspace of the United States while also enabling greater operational capabilities.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

Vol. 84

Tuesday,

No. 250

December 31, 2019

Part II

14 CFR Parts 1, 47, 48, et al.

Remote Identification of Unmanned Aircraft Systems; Proposed Rule

Federal Register / Vol. 84 , No. 250 / Tuesday, December 31, 2019 / Proposed Rules DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Parts 1, 47, 48, 89, 91, and 107

14 CFR Parts 1, 47, 48, 89, 91, and 107

[Docket No.: FAA-2019-1100; Notice No. 20-01] RIN 2120-AL31

Remote Identification of Unmanned Aircraft Systems

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking.

SUMMARY: This action would require the remote identification of unmanned aircraft systems. The remote identification of unmanned aircraft systems in the airspace of the United States would address safety, national security, and law enforcement concerns regarding the further integration of these aircraft into the airspace of the United States while also enabling greater operational capabilities.

Dates

DATES: Send comments on or before March 2, 2020.

ADDRESSES: Send comments identified by docket number FAA-2019-1100 using any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov and follow the online instructions for sending your comments electronically.

Addresses

• Mail: Send comments to Docket Operations, M-30; U.S. Department of Transportation (DOT), 1200 New Jersey Avenue SE, Room W12-140, West Building Ground Floor, Washington, DC 20590-0001.

• Hand Delivery or Courier: Take comments to Docket Operations in Room W12-140 of the West Building Ground Floor at 1200 New Jersey Avenue SE, Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

• Fax: Fax comments to Docket Operations at 202-493-2251.

Privacy: In accordance with 5 U.S.C. 553(c), DOT solicits comments from the public to better inform its rulemaking process. DOT posts these comments, without edit, including any personal information the commenter provides, to http://www.regulations.gov.

Docket: Background documents or comments received may be read at http://www.regulations.gov at any time. Follow the online instructions for accessing the docket or go to Docket Operations in Room W12-140 of the West Building Ground Floor at 1200 New Jersey Avenue SE, Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Ben Walsh, Flight Technologies and Procedures Division, Federal Aviation Administration, 470 L'Enfant Plaza SW, Suite 4102, Washington, DC 20024; telephone 1-844-FLY-MY-UA; email: [email protected].

SUPPLEMENTARY INFORMATION:

Table of Contents

I. Executive Summary

I. Executive Summary

A. Introduction and Overview

B. Purpose of the Regulatory Action

C. Summary of the Proposed Rule

D. Summary of Costs and Benefits

E. Structure of This Proposed Rule II. Authority for This Rulemaking III. Integration of UAS Into the Airspace of the United States IV. Need for Remote Identification of UAS Operating in the Airspace of the United States

A. Maintaining the Safety and Efficiency of the Airspace of the United States

B. Unmanned Aircraft Systems Traffic Management (UTM)

C. Facilitating Beyond Visual Line of Sight Operations

D. National Security and Law Enforcement Efforts V. Related International Activities VI. Aviation Rulemaking Committee

A. ARC Recommendations Final Report

B. FAA Response to ARC Report VII. Terms Used in this Proposed Rule VIII. Applicability of Remote Identification Requirements IX. Changes to Registration Requirements

A. Registration Under Part 47

B. Registration Under Part 48

C. Issues With the Current Registration Requirements and Proposed Changes

D. Proposed Changes to the Registration Requirements To Require a Serial Number and Telephone Number as Part of the Registration Process

E. Request for Comments Regarding Serial Number Requirements

F. Serial Number Marking X. Operating Requirements for Remote Identification

A. Requirement To Broadcast or Transmit

B. Prohibition from Using ADS-B To Satisfy Remote Identification Requirements

C. Internet Availability and Transmission to a Remote ID USS

D. In-flight Loss of Connectivity with a Remote ID USS or Loss of Functionality

E. Valid Declaration of Compliance

F. Foreign Registered Civil Unmanned Aircraft Operated in the United States

G. Example Operating Scenarios XI. Law Enforcement Access to Remote Identification and Registration Information XII. Means of Compliance

A. Introduction

B. Applicability

C. Remote Identification Message Elements

D. Minimum Performance Requirements

E. Other Performance Requirements Considered

F. Submission and FAA Acceptance of Means of Compliance

G. Rescission of a Means of Compliance

H. Record Retention Requirements XIII. Design and Production Requirements

A. Applicability and Summary of Requirements

B. Requirement To Issue Serial Numbers

C. Requirement To Label UAS

D. Requirement for a UAS To Be Designed and Produced Using an FAA-Accepted Means of Compliance

E. Requirement To Submit a Declaration of Compliance

F. Accountability XIV. Remote Identification UAS Service Suppliers

A. UAS Service Suppliers (USS)

B. Remote ID USS

C. Data Privacy and Information Security XV. FAA-Recognized Identification Areas

A. Eligibility

B. Process to Request an FAA-Recognized Identification Area

C. Amendment

D. Duration of an FAA-Recognized Identification Area

E. Expiration and Termination

F. Petition To Reconsider the FAA's Decision To Terminate and FAA-Recognized Identification Area XVI. Use of ADS-B Out and Transponders XVII. Proposed Effective and Compliance Dates XVIII. Proposed Guidance Documents XIX. Regulatory Notices and Analyses

A. Regulatory Evaluation

B. Regulatory Flexibility Determination

C. International Trade Impact Assessment

D. Unfunded Mandates Assessment

E. Paperwork Reduction Act

F. International Compatibility and Cooperation

G. Environmental Analysis XX. Executive Order Determinations

A. Executive Order 13132, Federalism

B. Executive Order 13211, Regulations that Significantly Affect Energy Supply, Distribution, or Use

C. Executive Order 13609, Promoting International Regulatory Cooperation XXI. Tribal Considerations XXII. Privacy XXIII. Additional Information

A. Comments Invited

B. Confidential Business Information

C. Availability of Rulemaking Documents

D. Small Business Regulatory Enforcement Fairness Act

List of Abbreviations Frequently Used in This Document

List of Abbreviations Frequently Used in This Document

AC--Advisory Circular ADS-B--Automatic Dependent Surveillance-Broadcast ARC--Aviation Rulemaking Committee ATC--Air traffic control BVLOS--Beyond visual line of sight DOT--U.S. Department of Transportation FAA--Federal Aviation Administration GPS--Global Positioning System ICAO--International Civil Aviation Organization IFR--Instrument flight rules MOA--Memorandum of Agreement OMB--Office of Management and Budget UAS--Unmanned aircraft system USS--UAS service supplier UTM--Unmanned aircraft systems traffic management

I. Executive Summary

I. Executive Summary

A. Introduction and Overview

This proposed rule would establish requirements for the remote identification of unmanned aircraft systems (UAS) \1\ operated in the airspace of the United States. Remote identification (or Remote ID) is the ability of an unmanned aircraft in flight to provide certain identification and location information that people on the ground and other airspace users can receive. This is an important building block in the unmanned traffic management ecosystem. For example, the ability to identify and locate UAS operating in the airspace of the United States provides additional situational awareness to manned and unmanned aircraft. This will become even more important as the number of UAS operations in all classes of airspace increases. In addition, the ability to identify and locate UAS provides critical information to law enforcement and other officials charged with ensuring public safety. While remote identification alone will not enable routine expanded operations such as operations over people or beyond visual line of sight, it is a critical element for building unmanned traffic management capabilities. The FAA envisions that the remote identification network will form the foundation for the development of other technologies that can enable expanded operations.

A. Introduction and Overview

\1\ The FAA does not use the terms unmanned aircraft system and unmanned aircraft interchangeably. The FAA uses the term unmanned aircraft as defined in 14 CFR 1.1 to refer specifically to the unmanned aircraft itself. The FAA uses the term unmanned aircraft system to refer to both the unmanned aircraft and any communication links and components that control the unmanned aircraft. As explained in section VII of this proposed rule, the FAA is proposing to add the definition of unmanned aircraft system to part 1 of 14 CFR.

Full implementation of remote identification relies on three interdependent parts that are being developed concurrently. The first is this proposed rule, which establishes operating requirements for UAS operators and performance-based design and production standards for producers of UAS. The second is a network of Remote ID UAS Service Suppliers (Remote ID USS) that would collect the identification and location in real-time from in-flight UAS. The Remote ID USS would perform this service under contract with the FAA, based on the same model the FAA currently uses for the Low Altitude Authorization and Notification Capability (LAANC).\2\ The third part of the remote identification ecosystem is the collection of technical requirements that standards-setting organizations will develop to meet the performance-based design and production requirements in this proposed rule.

\2\ For more information on LAANC, consult https://www.faa.gov/uas/programs_partnerships/data_exchange/. On December 20, 2018, the FAA issued a request for information (RFI) seeking data exchange strategies and demonstrations for potential Remote ID USS. For more information on the RFI, consult https://faaco.faa.gov/index.cfm/announcement/view/32514.

All UAS operating in the airspace of the United States, with very few exceptions, would be subject to the requirements of this rule. All UAS operators would be required to comply regardless of whether they conduct recreational or commercial operations, except those flying UAS that are not otherwise required to be registered under the FAA's existing rules. All UAS produced for operation in the airspace of the United States would have to comply with the design and production requirements established in this proposal with exceptions for amateur-built UAS, UAS of the United States government, and unmanned aircraft that weigh less than 0.55 pounds.

This proposal establishes design and production requirements for two categories of remote identification: Standard remote identification UAS and limited remote identification UAS. Standard remote identification UAS would be required to broadcast identification and location information directly from the unmanned aircraft and simultaneously transmit that same information to a Remote ID USS through an internet connection. Limited remote identification UAS would be required to transmit information through the internet only, with no broadcast requirements; however, the unmanned aircraft would be designed to operate no more than 400 feet from the control station. Under this proposal, the vast majority of UAS would be required to comply with one of these two categories of remote identification. For those limited exceptions, which include certain amateur-built UAS and UAS manufactured prior to the compliance date, operators flying UAS without remote identification capabilities would be permitted to fly only at certain specific geographic areas established under this rule specifically to accommodate them.

This proposal envisions that within three years of the effective date of this rule, all UAS operating in the airspace of the United States will be compliant with the remote identification requirements. No UAS could be produced for operation in the United States after two years and no UAS could be operated after three years except in accordance with the requirements of this proposal. Details on the requirements and their applicability are in the sections that follow.

B. Purpose of the Regulatory Action

B. Purpose of the Regulatory Action

The FAA is integrating unmanned aircraft systems (UAS) operations into the airspace of the United States through a phased, incremental, and risk-based approach.\3\

\3\ Consult https://www.faa.gov/uas for additional information regarding UAS operations.

On June 28, 2016, the FAA achieved a major step towards UAS integration when it published the final rule for Operation and Certification of Small Unmanned Aircraft Systems.\4\ This was one of multiple UAS-related regulatory actions taken by the FAA to enable the safe integration of UAS into the airspace of the United States. As technology progresses and the utility of UAS increases, the FAA anticipates a need for further rulemaking to continue to foster the safe, secure, and efficient use of the airspace of the United States. The FAA believes that the next step in the regulatory process is to develop regulatory requirements that enable the remote identification of UAS operating in the airspace of the United States.

\4\ 81 FR 42064.

The remote identification of UAS is necessary to ensure public safety and the safety and efficiency of the airspace of the United States. The remote identification framework would provide UAS-specific data, which could be used in tandem with new technologies and infrastructure to facilitate future, more advanced operational capabilities (such as detect-and-avoid and aircraft-to-aircraft communications that support beyond visual line of sight operations) and to develop the necessary elements for comprehensive UAS traffic management (UTM). Furthermore, remote identification of UAS would provide airspace awareness to the FAA, national security agencies, and law enforcement entities. This information could be used to distinguish compliant airspace users from those potentially posing a safety or security risk.

Current rules for registration and marking of unmanned aircraft facilitate the identification of the owners of unmanned aircraft, but normally only upon physical examination of the aircraft. Existing electronic surveillance technologies like transponders and Automatic Dependent Surveillance-Broadcast (ADS-B), in addition to radio communications with air traffic control (ATC), were all considered as potential solutions for the remote identification of UAS but were determined to be unsuitable due to the lack of infrastructure for these technologies at lower altitudes and the potential saturation of available radio frequency spectrum. The FAA proposes to address the identification issues associated with UAS by requiring the use of new services and technology to enable the remote identification of UAS.

The proposed remote identification requirements are consistent with the FAA's safety mission of overseeing and promoting safety in air commerce and national security as well as promoting the safe and efficient use of the navigable airspace. The newly-available information would serve the public interest of enhancing safety, efficiency, and security in air commerce by creating situational awareness of all UAS flying in the airspace of the United States, which would allow additional and more complex UAS operations to take place. Remote identification would also strengthen the FAA's oversight of UAS operations and support efforts of law enforcement and national security agencies to address and mitigate disruptive behavior and hazards, which may threaten the safety and security of the airspace of the United States, other UAS, manned aviation, and persons and property on the ground. Remote identification information provided in near real-time would also assist Federal security partners in threat discrimination--allowing them to identify an operator and make an informed decision regarding the need to take actions to mitigate a perceived security or safety risk. The proposed rule would enhance the FAA's ability to monitor compliance with applicable regulations; would contribute to the FAA's ability to undertake compliance, enforcement, and educational actions required to mitigate safety risks; and would advance the safe integration of UAS into the airspace of the United States.

C. Summary of the Proposed Rule

C. Summary of the Proposed Rule

This proposed rule provides a framework for remote identification of all UAS operating in the airspace of the United States. The rule would facilitate the collection and storage of certain data such as identity, location, and altitude regarding an unmanned aircraft and its control station.

The FAA is proposing to tie the remote identification requirements to the registration of unmanned aircraft because the FAA and law enforcement agencies have a need to correlate remote identification and registration data. The proposed rule would therefore impose operating requirements on persons operating unmanned aircraft registered or required to be registered under title 14, Code of Federal Regulations (CFR), part 47 or part 48, and on persons operating foreign civil unmanned aircraft in the United States. The proposed rule would also impose requirements on persons applying for and using FAA-recognized identification areas (areas specifically recognized by the FAA where UAS without remote identification equipment could operate) and requirements for persons developing means of compliance (e.g., standards) that describe how a UAS would be designed and produced to meet the performance requirements proposed in this rule. Finally, the proposed rule would require persons designing and producing UAS with remote identification for operations in the United States to produce them using an FAA-accepted means of compliance.

UAS owners, UAS operators (including pilots, remote pilots, recreational flyers, and other persons manipulating the flight controls of UAS), UAS designers and producers, developers of remote identification means of compliance, and Remote Identification UAS Service Suppliers (Remote ID USS) would have important roles in the remote identification of UAS. The subsections that follow describe the roles and responsibilities of each of these groups within the scope of the proposed rule. 1. UAS Owners

The FAA proposes to revise the registration requirements to require all owners of unmanned aircraft to register each unmanned aircraft individually when registering under part 48. Furthermore, the owners of standard or limited remote identification unmanned aircraft would have to provide the serial number of all unmanned aircraft registered under part 47 or part 48, on or before the 36th month after the effective date of the final rule. The serial number would establish the unique identity of the unmanned aircraft. The serial number provided during registration or re-registration would have to be issued by the producer of the unmanned aircraft and comply with the ANSI/CTA-2063-A serial number standard.

Owners of unmanned aircraft used exclusively for limited recreational operations \5\ who currently register multiple aircraft under a single registration number would be required to register each aircraft, individually by manufacturer, model, and, if the unmanned aircraft is a standard or limited remote identification unmanned aircraft, the aircraft's serial number, on or before the 36th month after the effective date of the final rule. The owners of small unmanned aircraft registered after the effective date of the final rule would have to comply with the new registration requirements prior to the operation of the unmanned aircraft.

\5\ This proposal uses the term "limited recreational operations" when discussing current registration requirements under part 48. Part 48 uses the term "model aircraft" to describe recreational UAS operations. The FAA considers that model aircraft under part 48 are consistent with the "limited recreational operations" described in 49 U.S.C. 44809, therefore "limited recreational operations" has been used throughout to ensure consistency of terminology with current statutory requirements.

The registration requirements are discussed in section IX of this preamble. 2. UAS Operators i. Remote Identification Operating Requirements

Under the proposed rule, a person operating a UAS in the airspace of the United States would have to meet the remote identification requirements in one of three ways, depending upon the capabilities of the UAS, on or before the 36th month after the effective date of the final rule. a. Standard Remote Identification UAS

For purposes of this proposed rule, a "standard remote identification UAS" is a UAS with remote identification equipment capable of both: (1) Connecting to the internet and transmitting through that internet connection to a Remote ID USS; and (2) broadcasting directly from the unmanned aircraft. Standard remote identification UAS are discussed further in section X.A.1 of this preamble. Any person operating a standard remote identification UAS would be required to ensure:

• The UAS was designed and produced to meet the minimum performance requirements of the rule using an FAA-accepted means of compliance for standard remote identification UAS. Persons would be able to meet this obligation by ensuring that the serial number of the standard remote identification UAS is listed on an FAA-accepted declaration of compliance. A person operating a UAS would be able to read the label on the aircraft indicating whether the UAS is a standard or limited remote identification UAS. Additionally, a person could determine whether the UAS is listed on an FAA-accepted declaration of compliance by verifying the status on the FAA's website. The standard remote identification UAS broadcasts the remote identification message elements directly from the unmanned aircraft from takeoff to landing.

• When the internet is available at takeoff, the standard remote identification UAS connects to the internet and transmits the required message elements through that internet connection to a Remote ID USS.

The required message elements include, among others, a UAS Identification to establish the unique identity of the UAS. Operators would have to choose whether to use the serial number of the unmanned aircraft or a session ID (e.g., a randomly-generated alphanumeric code assigned by a Remote ID USS on a per-flight basis designed to provide additional privacy to the operator) as the UAS Identification. The required message elements are discussed in section XII.C of this preamble.

A person could operate a standard remote identification UAS only if: (1) It has a serial number that is listed on an FAA-accepted declaration of compliance; (2) its remote identification equipment is functional and complies with the requirements of the proposed rule from takeoff to landing; and (3) its remote identification equipment and functionality have not been disabled. b. Limited Remote Identification UAS

For purposes of this proposed rule, a "limited remote identification UAS" is a UAS that: (1) Is designed and produced to restrict operation to no more than 400 feet from its control station; (2) is capable of connecting to the internet and transmitting the remote identification message elements through that internet connection to a Remote ID USS; and (3) cannot broadcast remote identification message elements. Limited remote identification UAS are discussed further in section X.A.2 of this preamble. Persons operating a limited remote identification UAS would be required to operate within visual line of sight and ensure that:

• The UAS was designed and produced to meet the minimum performance requirements of the rule using an FAA-accepted means of compliance for a limited remote identification UAS. Persons would be able to meet this obligation by ensuring that the serial number of the limited remote identification UAS is listed on an FAA-accepted declaration of compliance. Additionally, a person could determine whether the UAS is listed on an FAA-accepted declaration of compliance by verifying the status on the FAA's website.

• From takeoff to landing, the limited remote identification UAS connects to the internet and transmits the required remote identification message elements through that internet connection to a Remote ID USS.

The required message elements would include, among others, a UAS Identification to establish the unique identity of the UAS. Operators would have to choose whether to use the unmanned aircraft's serial number or a session ID assigned by a Remote ID USS as the UAS Identification. The required message elements are discussed in section XII.C of this preamble.

A person could operate a limited remote identification UAS only if: (1) it has a serial number that is listed on an FAA-accepted declaration of compliance; (2) its remote identification equipment is functional and complies with the requirements of the proposed rule from takeoff to landing; and (3) its remote identification equipment and functionality have not been disabled. Examples of the use of limited remoted identification UAS are further discussed in section X.G of this preamble. c. UAS Without Remote Identification Equipment

Under the proposed rule, the vast majority of UAS would be required to have remote identification capability, however as discussed in section X. A. 3, a limited number of UAS would continue to not have remote identification. The FAA envisions that upon full implementation of this rule, no unmanned aircraft weighing more than 0.55 pounds will be commercially available that is not either a standard remote identification UAS or a limited remote identification UAS. However, there will be certain UAS including amateur built aircraft and previously manufactured UAS that might not have remote identification capability. A person operating a UAS without remote identification equipment would always be required to operate within visual line of sight \6\ and within an FAA-recognized identification area. Under the proposed rule, an FAA-recognized identification area is a defined geographic area where UAS without remote identification can operate. An area would be eligible for establishment as an FAA-recognized identification area if it is a flying site that has been established within the programming of a community based organization recognized by the Administrator. The FAA would maintain a list of FAA-recognized identification areas at https://www.faa.gov. FAA-recognized identification areas are discussed further in section XV of this preamble.

\6\ While this proposed rule does not propose any changes to requirements related to beyond visual line of sight (BVLOS) operations, the FAA intends for the rule to be dynamic to account for future changes related to line of sight operations. The FAA specifically notes that this rulemaking requires UAS without remote identification equipment to always be operated within line of sight.

ii. Prohibition Against the Use of ADS-B Out and Transponders

ii. Prohibition Against the Use of ADS-B Out and Transponders

The proposed rule also prohibits use of ADS-B Out and transponders for UAS operations under 14 CFR part 107 and part 91 unless otherwise authorized by the FAA. The FAA is concerned that the potential proliferation of ADS-B Out transmitters on UAS may negatively affect the safe operation of manned aircraft in the airspace of the United States. The projected numbers of UAS operations have the potential to saturate available ADS-B frequencies, affecting ADS-B capabilities for manned aircraft and potentially blinding ADS-B ground receivers. The FAA is therefore proposing that UAS operators, with limited exceptions, be prohibited from using ADS-B Out or transponders. The prohibition against the use of ADS-B Out and transponders is discussed in Section XVI of this preamble. 3. UAS Designers and Producers

For each UAS designed or produced for operation in the United States, the person responsible for the design or production of the unmanned aircraft system (with limited exceptions included in the proposal) would be required to design or produce the UAS in accordance with the performance requirements for a standard remote identification UAS or limited remote identification UAS using an FAA-accepted means of compliance for remote identification on or before the 24th month after the effective date of the final rule.

A person responsible for the production of UAS (with limited exceptions) would be required to:

• Issue each unmanned aircraft a serial number that complies with the ANSI/CTA-2063-A serial number standard.

• Label the unmanned aircraft to indicate that it is remote identification compliant and indicate whether the UAS is standard remote identification or limited remote identification.

• Submit a declaration of compliance for acceptance by the FAA, declaring that the UAS complies with the requirements of the proposed rule.

The FAA could ask the person responsible for the production of the UAS to submit additional information or documentation, as needed, to supplement a declaration of compliance. The FAA would notify the submitter of its acceptance of a declaration of compliance. The FAA would also provide a list of accepted declarations of compliance at https://www.faa.gov.

A person that submits a declaration of compliance would be required to retain certain data for as long as the UAS listed on that declaration of compliance is produced plus an additional 24 calendar months. If the FAA rescinds its acceptance of a declaration of compliance, the submitter of the FAA-accepted declaration of compliance or any person adversely affected by the rescission of the Administrator's acceptance of the declaration of compliance may petition the FAA to reconsider the rescission by submitting a request for reconsideration to the FAA within 60 calendar days of publication in the Federal Register of a notice of rescission. 4. Developers of Remote Identification Means of Compliance

Means of compliance, as discussed in section XII of this preamble, are developed by persons or organizations to describe methods by which a person designing or producing a UAS with remote identification may comply with the performance requirements of this proposed rule. Under the proposed rule, a means of compliance would have to be accepted by the FAA before it could be used for the design and production of UAS with remote identification. A person or entity seeking acceptance by the FAA of a means of compliance for UAS with remote identification equipment would be required to submit the means of compliance to the FAA. The FAA would review the means of compliance to determine if it meets the minimum performance requirements, and testing and validation procedures of the proposed rule. Specifically, the person or entity would have to submit a detailed description of the means of compliance, a justification for how the means of compliance meets the minimum performance requirements of the proposed rule, and any substantiating material the person or entity wishes the FAA to consider as part of the application. The minimum performance requirements, and testing and validation procedures, are discussed in sections XII.D and XII.F of this preamble. A person or entity who submits a means of compliance that is accepted by the FAA would have to retain certain data for as long as the means of compliance is accepted plus an additional 24 calendar months.

The FAA would indicate acceptance of a means of compliance by notifying the submitter of the acceptance of the proposed means of compliance. The FAA also expects to notify the public that it has accepted the means of compliance by including it on a list of accepted means of compliance at https://www.faa.gov. The FAA would not disclose commercially valuable information in this document. 5. Remote ID USS

The proposed rule would require persons operating UAS with remote identification to transmit the remote identification message elements to a Remote ID USS over the internet. A Remote ID USS would be a service provider qualified by the Administrator to provide remote identification services to UAS. Each Remote ID USS would be required to establish a contractual relationship with the FAA through a Memorandum of Agreement (MOA) entered into under the FAA's "other transaction authority" under 49 U.S.C. 106(l) and (m), and to comply with a series of terms, conditions, limitations, and technical requirements that outline how the Remote ID USS must interpret and provide data to external users, as well as store and protect such data. The Remote ID USS would also be contractually required to meet quality-of- service metrics that would establish the minimum requirements for providing remote identification services, including availability of the service and what happens when various failures occur. To implement remote identification, the FAA anticipates establishing a cooperative data exchange mechanism between the FAA and Remote ID USS, as discussed in section XIV of this preamble.

Remote ID USS would be required to demonstrate four primary capabilities: (1) The ability to share the remote identification message elements in near real-time with the FAA upon request; (2) the ability to maintain remote identification information securely and to limit access to such information; (3) the ability to meet contractually-established technical parameters; and (4) the ability to inform the FAA when their services are active and inactive. Another capability of a Remote ID USS may be to generate and provide UAS operators with a UAS Identification known as a session ID. A session ID would be a randomly-generated alphanumeric code that is used only for one flight. UAS operators would have the option to use a Session ID to identify the UAS instead of the serial number, to provide a greater level of privacy. This capability would be defined in the technical requirements agreed to in the MOA.

To become an FAA-qualified Remote ID USS, a prospective Remote ID USS would enter into an MOA with the FAA, demonstrate it meets the technical requirements, and successfully test the end-to-end system and connections. Prospective Remote ID USS would also be reviewed for consistency with national security and cybersecurity requirements and export administration regulations. FAA-qualified Remote ID USS would be subject to ongoing FAA review to ensure compliance and quality-of-service. 6. Table of Major Provisions

Table 1 provides a summary of the major provisions of this proposed rule.

Table 1--Summary of Major Provisions

Issue Proposed requirement CFR section

Registration Requirements

Individual registration of Requires the individual 48.100

unmanned aircraft and registration of all 48.110

conforming changes. unmanned aircraft

registered under part

48.

Requires each unmanned 48.5

aircraft to be 48.30

registered under a 48.115

unique registration 48.200

number. Eliminates

existing option to

allow multiple

recreational unmanned

aircraft to register

under a single

registration number.

Serial numbers for unmanned The unmanned aircraft 47.14

aircraft. serial number provided

as part of an

application for

aircraft registration

for a standard remote

identification or

limited remote

identification

unmanned aircraft

would be the serial

number issued by the

manufacturer in

accordance with the

requirements of part

89.

The owner of a small 48.100

unmanned aircraft

would have to include

the manufacturer and

model name of the

unmanned aircraft

during the

registration or

registration renewal

process, and for any

standard or limited

remote identification

unmanned aircraft, the

serial number issued

by the manufacturer.

Adds clarifying 48.15

language for existing

registration

requirements for part

107 operators.

Telephone number(s) for Requires telephone 48.100

applicant for registration. number(s) of applicant

at time of

registration.

Operating Requirements

Applicability of operating The remote 89.101

requirements. identification

operating requirements

would apply to: (1)

Persons operating

unmanned aircraft

registered or required

to be registered under

parts 47 or 48; and

(2) persons operating

foreign civil unmanned

aircraft in the United

States.

Remote identification No person would be 89.105

requirements generally. allowed to operate a

UAS within the

airspace of the United

States unless the

operation is conducted

under one of the

following: (1) The UAS

is a standard remote

identification UAS and

that person complies

with the requirements

of § 89.110; (2)

the UAS is a limited

remote identification

UAS and that person

complies with the

requirements of Sec.

89.115; or (3) the UAS

does not have remote

identification

equipment and that

person complies with

the requirements of

§ 89.120.

Standard remote identification Remote identification.. 89.110

UAS. If the internet is

available at takeoff,

the UAS would have to

do the following from

takeoff to landing:

(1) Connect to the

internet and transmit

the required remote

identification message

elements through that

internet connection to

a Remote ID USS; and

(2) broadcast the

message elements

directly from the

unmanned aircraft..

If the internet is

unavailable at

takeoff, or if during

the flight, the

unmanned aircraft can

no longer transmit

through an internet

connection to a Remote

ID USS, the UAS would

have to broadcast the

message elements

directly from the

unmanned aircraft from

takeoff to landing.

In-flight loss of

broadcast capability:

A person manipulating

the flight controls of

a standard remote

identification UAS

that can no longer

broadcast the message

elements would have to

land as soon as

practicable.

Operation of standard

remote identification

UAS:

A person would be

allowed to operate

a standard remote

identification UAS

only if it meets

the following

requirements: (1)

Its serial number

is listed on an FAA-

accepted

declaration of

compliance; (2) its

remote

identification

equipment is

functional and

complies with the

requirements of

proposed part 89

from takeoff to

landing; and (3)

its remote

identification

equipment and

functionality have

not been disabled.

Limited remote identification Remote identification.. 89.115

UAS. The UAS would have to

do the following from

takeoff to landing:

(1) Connect to the

internet and transmit

the required remote

identification message

elements through that

internet connection to

a Remote ID USS; and

(2) be operated within

visual line of sight..

In-flight loss of

remote identification:

A person manipulating

the flight controls of

a limited remote

identification UAS

would have to land as

soon as practicable

when it cannot

transmit the message

elements through an

internet connection to

a Remote ID USS.

Operation of limited

remote identification

UAS:

A person would be

allowed to operate a

limited remote

identification UAS

only if it meets the

following

requirements: (1) Its

serial number is

listed on an FAA-

accepted declaration

of compliance; (2) its

remote identification

equipment is

functional and

complies with the

requirements of

proposed part 89 from

takeoff to landing;

and (3) its remote

identification

equipment and

functionality have not

been disabled.

UAS without remote The limited number of 89.120

identification. UAS that do not have

remote identification

equipment would be

allowed to operate

within visual line of

sight and within an

FAA-recognized

identification area.

With authorization from

the Administrator, a

person may operate a

UAS that does not have

remote identification

for the purpose of

aeronautical research

or to show compliance

with regulations.

Transponder and Automatic ADS-B Out equipment may 89.125

Dependent Surveillance- not be used to comply

Broadcast (ADS-B) use. with the remote

identification

requirements.

ATC transponder and 91.215

altitude-reporting

equipment and use

requirements do not

apply to persons

operating UAS unless

the operation is

conducted under a

flight plan and the

person operating the

UAS maintains two-way

radio communication

with ATC, or the use

of a transponder is

otherwise authorized

by the Administrator.

No person would be 107.52

allowed to operate a

small UAS with a

transponder on, unless

otherwise authorized

by the Administrator.

ADS-B equipment and use 91.225

requirements do not

apply to persons

operating UAS unless

the operation is

conducted under a

flight plan and the

person operating the

UAS maintains two-way

radio communication

with ATC, or the use

of ADS-B Out is

otherwise authorized

by the Administrator.

No person would be 107.53

allowed to operate a

small UAS with ADS-B

Out equipment in

transmit mode, unless

otherwise authorized

by the Administrator.

Confirmation of identification No person would be 89.130

for foreign registered civil allowed to operate a

unmanned aircraft operated in foreign registered

the United States. civil unmanned

aircraft in the United

States unless, prior

to the operation, the

person submits a

notice of

identification that

includes basic

information regarding

the unmanned aircraft

and the person

responsible for the

operation.

Record Retention … The Administrator shall 89.135

require any Remote ID

USS to retain any

remote identification

message elements for 6

months from the date

when the remote

identification message

elements are received

or otherwise come into

the possession of the

Remote ID USS.

FAA-recognized identification areas

Applicability … Prescribes procedural 89.201

requirements to

establish an FAA-

recognized

identification area.

Eligibility … Only a community based 89.205

organization (CBO)

recognized by the

Administrator would be

allowed to apply for

the establishment of

an FAA-recognized

identification area.

Requests for establishment … Application … 89.210

A CBO requesting

establishment of an

FAA-recognized

identification area

would have to submit

an application within

12 calendar months

from the effective

date of the final

rule. The FAA will not

consider any

applications submitted

after that date.

Required documentation. 89.210

A request for

establishment of an

FAA-recognized

identification area

would have to contain

the following

information:

• Name of the

CBO making the

request..

• Declaration

that the person making

the request has the

authority to act on

behalf of the CBO.

• Name and

contact information,

including telephone

number(s), of the

primary point of

contact for

communications with

the FAA.

• Physical

address of the

proposed FAA-

recognized

identification area.

• Latitude and

longitude coordinates

delineating the

geographic boundaries

of the proposed FAA-

recognized

identification area.

• If applicable,

a copy of any existing

letter of agreement

regarding the flying

site.

Approval of an FAA- 89.215

recognized

identification area.

FAA would approve or

deny applications for

FAA-recognized

identification areas,

and may take into

consideration matters

including but not

limited to: the

effects on existing or

contemplated airspace

capacity, critical

infrastructure,

existing or proposed

manmade objects,

natural objects, or

the existing use of

the land, within or

close to the proposed

FAA-recognized

identification area;

the safe and efficient

use of airspace by

other aircraft; and

the safety and

security of persons or

property on the

ground.

Amendment … 89.220

Any change to the

information submitted

in the application for

establishment of an

FAA-recognized

identification area

would have to be

submitted to the FAA

within ten calendar

days of the change.

Such information

includes, but would

not be limited to, a

change to the point of

contact for the FAA-

recognized

identification area,

or a change to the

community based

organization's

affiliation with the

FAA-recognized

identification area.

If the community based

organization wishes to

change the geographic

boundaries of the FAA-

recognized

identification area,

the organization must

submit the request to

the FAA for review.

The geographic

boundaries of the FAA-

recognized

identification area

will not change until

they have been

approved or denied in

accordance with Sec.

89.215.

Duration of an FAA- 89.225

recognized

identification area.

An FAA-recognized

identification area

would be in effect for

48 calendar months

after the date the FAA

approves the request

for establishment of

an FAA-recognized

identification area.

Renewal … 89.225

A request for renewal

would have to be

submitted no later

than 120 days prior to

the expiration of the

FAA-recognized

identification area in

a form and manner

acceptable to the

Administrator. The

Administrator may deny

requests submitted

after that deadline or

requests submitted

after the expiration

of the FAA-recognized

identification area.

Expiration and termination … Expiration … 89.230

Unless renewed, an FAA-

recognized

identification area

would be automatically

cancelled and have no

further force or

effect as of the day

immediately after its

expiration date..

Termination prior to

expiration (by

request):

A CBO may submit a

request to the

Administrator to

terminate an FAA-

recognized

identification area.

Once an FAA-recognized

identification area is

terminated, that CBO

may not reapply to

have that flying site

reestablished as an

FAA-recognized

identification area.

Termination by FAA:

FAA would be able to

terminate an FAA-

recognized

identification area

for cause or upon a

finding that the FAA-

recognized

identification area

could pose a risk to

aviation safety,

public safety, or

national security or

that the person who

submitted a request

for establishment of

an FAA-recognized

identification area

provided false or

misleading information

during the submission

process.

Once an FAA-recognized

identification area is

terminated, that CBO

may not reapply to

have that flying site

reestablished as an

FAA-recognized

identification area.

Petition to reconsider

the FAA's decision to

terminate an FAA

recognized

identification area:

A CBO whose FAA-

recognized

identification area

has been terminated by

the FAA would be able

to petition for

reconsideration by

submitting a request

for reconsideration

and establishing the

grounds for such

reconsideration within

30 calendar days of

the date of issuance

of the termination.

Requirements for UAS with Remote Identification

Applicability … Prescribes the minimum 89.301

message elements set

and minimum

performance

requirements for

standard remote

identification UAS and

limited remote

identification UAS.

Message elements broadcast and Standard remote 89.305

transmitted by standard remote identification UAS

transmitted by standard remote identification UAS

identification UAS. would have to

broadcast and transmit

the following remote

identification message

elements:

• The identity

of the UAS consisting

of one of the

following:.

[cir] The serial number

assigned to the

unmanned aircraft by

the producer..

[cir] Session ID

assigned by a Remote

ID USS..

• An indication

of the latitude and

longitude of the

control station and

unmanned aircraft..

• An indication

of the barometric

pressure altitude of

the control station

and unmanned aircraft..

• A Coordinated

Universal Time (UTC)

time mark..

• An indication

of the emergency

status of the UAS,

which could include

lost-link or downed

aircraft..

Minimum performance Standard remote 89.310

requirements for standard identification UAS

remote identification UAS. would have to meet

minimum performance

requirements related

to the following:

• Control

station and unmanned

aircraft location..

• Automatic

Remote ID USS

connection..

• Time mark.

• Self-testing

and monitoring.

• Tamper

resistance.

• Connectivity.

• Error

correction.

• Interference

considerations.

• Message

transmission

requirements for

broadcast and Remote

ID USS transmission.

• Message

elements performance

requirements for

broadcast and Remote

ID USS transmission.

• Cybersecurity.

Message elements transmitted by Limited remote 89.315

limited remote identification identification UAS

UAS. would have to transmit

the following remote

identification message

elements:

• The identity

of the UAS consisting

of one of the

following:.

[cir] The serial number

assigned to the

unmanned aircraft by

its producer.

[cir] Session ID

assigned by a Remote

ID USS.

• An indication

of the latitude and

longitude of the

control station.

• An indication

of the barometric

pressure altitude of

the control station.

• A Coordinated

Universal Time (UTC)

time mark.

• An indication

of the emergency

status of the UAS,

which could include

lost-link or downed

aircraft.

Minimum performance Limited remote 89.320

requirements for limited identification UAS

remote identification UAS. would have to meet

minimum performance

requirements related

to the following:

• Control

station location..

• Automatic

Remote ID USS

connection..

• Time mark.

• Self-testing

and monitoring.

• Tamper

resistance.

• Connectivity.

• Error

correction.

• Interference

considerations.

• Message

transmission

requirements for

Remote ID USS

transmission.

• Message

elements performance

requirements for

Remote ID USS

transmission.

• Cybersecurity.

• Range

limitation.

• Broadcast

limitation.

Means of Compliance

Applicability … Prescribes the 89.401

following:

• Requirements

for means of

compliance.

• Procedural

requirements for the

submission and

acceptance of means of

compliance.

• Rules

governing persons

submitting means of

compliance for FAA

acceptance.

Submitting a means of Any person would be 89.405

compliance for FAA acceptance. able to submit a means

compliance for FAA acceptance. able to submit a means

of compliance for

acceptance by the FAA

by submitting certain

specified information

to the FAA in a form

and manner acceptable

to the Administrator.

A means of compliance

would have to include

testing and validation

procedures for persons

designing and

producing standard

remote identification

UAS or limited remote

identification UAS to

demonstrate through

analysis, ground test,

or flight test, as

appropriate, how the

standard remote

identification UAS or

limited remote

identification UAS

performs its intended

functions and meets

the requirements for

UAS with remote

identification.

Acceptance of a means of A person requesting 89.410

compliance. acceptance of a means

of compliance would

have to demonstrate to

the FAA that the means

of compliance

addresses all

applicable

requirements and that

any UAS with remote

identification

designed and produced

in accordance with

such means of

compliance would meet

the performance

requirements of

proposed part 89.

Rescission … Rescission of FAA's 89.415

acceptance of a means

of compliance.

FAA would be able to

rescind its acceptance

of a means of

compliance if it finds

that the means of

compliance does not

meet any of the

applicable

requirements for a

means of compliance..

Record retention … A person who submits a 89.420

means of compliance

that is accepted by

the Administrator

would have to retain

certain specified data

for as long as the

means of compliance is

accepted plus an

additional 24 calendar

months.

Design and Production of UAS with Remote Identification

Applicability … Applies to the design 89.501

and production of UAS

operating in the

United States except

for the design and

production of the

following (unless they

are standard remote

identification UAS or

limited remote

identification UAS, in

which case they would

have to comply with

the design and

production

requirements of the

proposed rule):

• Amateur-built

UAS.

• UAS of the

United States

Government.

• UAS where the

unmanned aircraft

weighs less than 0.55

pounds including the

weight of anything

attached to or carried

by the aircraft.

• UAS produced

for the purpose of

aeronautical research

or showing compliance

with regulations.

Prescribes the

following:

• Requirements

for design and

production of UAS

operating in the

United States.

• Procedural

requirements for the

submission and

acceptance of

declarations of

compliance.

• Rules

governing persons

holding FAA-accepted

declarations of

compliance or

operating UAS with

remote identification.

Serial numbers … Producers of UAS with 89.505

remote identification

would have to issue

each unmanned aircraft

a serial number that

complies with ANSI/CTA-

2063-A.

Design and production No person would be 89.510

requirements. allowed to produce a

UAS unless.

• The UAS is

designed and produced

to meet the minimum

performance

requirements for

standard remote

identification UAS or

limited remote

identification UAS

using an FAA-accepted

means of compliance.

• The UAS meets

the requirements of

proposed subpart F.

• The FAA has

accepted a declaration

of compliance for that

UAS.

Producers of UAS would

have to:

• Allow the

Administrator to

inspect their

facilities, technical

data, and any standard

remote identification

UAS or limited remote

identification UAS the

person produces, and

to witness any tests

necessary to determine

compliance with

subpart F.

• Perform

independent audits on

a recurring basis, and

whenever the FAA

provides notice of

noncompliance or of

potential

noncompliance, to

demonstrate the UAS

listed under a

declaration of

compliance meet the

requirements of

subpart F. The person

responsible for the

production of standard

remote identification

UAS or limited remote

identification UAS

must provide the

results of all such

audits to the FAA upon

request.

• Maintain

product support and

notification

procedures to notify

the public and the FAA

of any defect or

condition that causes

a UAS to no longer

meet the requirements

of subpart F, within

15 calendar days of

the date the person

becomes aware of the

defect or condition.

Labeling … Persons responsible for 89.515

the production of UAS

with remote

identification would

have to include a

label on the UAS to

indicate that it meets

the remote

identification

requirements and

whether the unmanned

aircraft system is a

standard remote

identification UAS or

limited remote

identification UAS.

The label would have

to be in English and

be legible, prominent,

and permanently

affixed to the

unmanned aircraft.

Submission of declaration of The person responsible 89.520

compliance for FAA acceptance. for the production of

a UAS with remote

compliance for FAA acceptance. for the production of

identification

equipment would have

to submit a

declaration of

compliance for

acceptance by the FAA.

The declaration of

compliance would have

to include certain

specified information,

including a

declaration that:

• The UAS was

designed and produced

using an FAA-accepted

means of compliance.

• The person

responsible for the

production of the UAS

complies with the

requirements of Sec.

89.510(b).

Acceptance of a declaration of The FAA would notify 89.525

compliance. the submitter of its

decision to accept or

reject a declaration

of compliance.

Rescission and reconsideration. Rescission of FAA's 89.530

acceptance of a

declaration of

compliance.

The FAA would be able

to rescind its

acceptance of a

declaration of

compliance if it

determines any of the

following: (1) A UAS

with remote

identification listed

under an FAA-accepted

declaration of

compliance does not

meet the applicable

minimum performance

requirements; (2) an

FAA-accepted

declaration of

compliance does not

meet any of the

relevant requirements

of proposed part 89;

or (3) the FAA

rescinded its

acceptance of the

means of compliance

listed in an FAA-

accepted declaration

of compliance.

If the FAA determines

it is in the public

interest, prior to

rescission, it would

be able to provide a

reasonable period of

time for the person

holding the

declaration of

compliance to

remediate the

noncompliance.

Petition for

reconsideration:

The person who

submitted the FAA-

accepted declaration

of compliance or any

person adversely

affected by the

rescission would be

able to petition for

reconsideration within

60 days of the

rescission. The

petition would have to

show that the

petitioner is an

interested party and

has been adversely

affected by the

rescission. The

petition would also

have to demonstrate

one of the following:

(1) The petitioner has

a significant

additional fact not

previously presented

to the FAA; (2) the

Administrator made a

material error of fact

in the decision to

rescind its

acceptance; or (3)

that the Administrator

did not correctly

interpret a law,

regulation, or

precedent.

Record retention … A person who submits a 89.535

declaration of

compliance that is

accepted by the

Administrator would

have to retain certain

specified data for as

long as the UAS listed

on that declaration of

compliance are

produced plus an

additional 24 calendar

months. That person

would have to also

make certain

information available

for inspection by the

FAA, including: (1)

The means of

compliance, all

documentation, and

substantiating data

related to the means

of compliance used;

(2) records of all

test results; and (3)

any other information

necessary to

demonstrate compliance

with the means of

compliance so that the

UAS meets the remote

identification

requirements and the

design and production

requirements of this

part.

Definitions and Abbreviations

Definitions … • Unmanned 1.1

aircraft system.

• UAS service

supplier..

• Visual line of

sight..

• Amateur-built 89.1

unmanned aircraft

system.

• Broadcast …

• Remote ID USS.

Abbreviations … • USS means a 1.2

UAS service supplier.

Falsification, Reproduction, Alteration, or Omission

Falsification, reproduction or No person would be 89.5

alteration. allowed to make or

cause to be made any

of the following.

• Any fraudulent

or intentionally false

statement in any

document related to

any acceptance,

application, approval,

authorization,

certificate,

declaration,

designation,

qualification, record,

report, request for

reconsideration, or

similar, submitted

under this part..

• Any fraudulent

or intentionally false

statement in any

document required to

be developed,

provided, kept, or

used to show

compliance with any

requirement under this

part.

• Any

reproduction or

alteration, for

fraudulent purpose, of

any document related

to any acceptance,

application, approval,

authorization,

certificate,

declaration,

designation,

qualification, record,

report, request for

reconsideration, or

similar, submitted or

granted under this

part.

No person may conceal a

material fact in:

• Any document

related to any

acceptance,

application, approval,

authorization,

certificate,

declaration,

designation,

qualification, record,

report, request for

reconsideration, or

similar, submitted

under this part.

• Any document

required to be

developed, provided,

kept, or used to show

compliance with any

requirement under this

part.

The commission of a

prohibited act would

result in:

• Suspension,

rescission, or

revocation of any

acceptance,

application, approval,

authorization,

certificate,

declaration,

declaration of

compliance,

designation, document,

filing, qualification,

means of compliance,

record, report,

request for

reconsideration, or

similar instrument

issued or granted by

the Administrator and

held by that person.

• A civil

penalty.

D. Summary of Costs and Benefits

D. Summary of Costs and Benefits

This proposed rule would provide remote identification of UAS in the airspace of the United States to address safety, security, and law enforcement concerns regarding the further integration of these aircraft into the airspace of the United States while also enabling greater operational capabilities. This proposal would promote public safety and the safety and efficiency of the airspace of the United States. The remote identification framework would provide UAS-specific data, which may be used in tandem with new technologies and infrastructure to facilitate more advanced operational capabilities (such as detect-and-avoid and aircraft-to-aircraft communications that support beyond visual line of sight operations) and to develop the necessary elements for comprehensive UAS traffic management (UTM). Furthermore, remote identification of UAS provides airspace awareness to the FAA, national security agencies, and law enforcement entities. This information could be used to distinguish compliant airspace users from those potentially posing a safety or security risk fulfilling a key requirement for law enforcement and national security agencies charged with protecting public safety.

This proposed rule would result in additional costs for persons responsible for the production of UAS, owners and operators of registered unmanned aircraft, community based organizations, Remote ID USS, and the FAA. This proposal would provide cost savings for the FAA and law enforcement resulting from a reduction in hours and associated costs expended investigating UAS incidents.\7\ Additionally, part 107 allows individuals to request waivers from certain provisions, including those prohibiting operations at night and over people. This proposed rule, in concert with the FAA's proposed rule for operations over people would create cost savings for the FAA and part 107 operators by avoiding the time expended processing waivers for these activities.\8\

\7\ This analysis includes quantified savings to the FAA only. A variety of other entities involved with airport operations, facility and infrastructure security, and law enforcement would also save time and resources involved with UAS identification and incident reporting, response and investigation. The FAA plans to update its estimates of savings for additional information and data identified during the comment period and development of the final rule.

\8\ On February 13, 2019, the FAA published a notice of proposed rulemaking titled "Operation of Small Unmanned Aircraft Systems over People," (84 FR 3856) in which the FAA proposed to allow operations of small unmanned aircraft over people in certain conditions and operations of small UAS at night without obtaining a waiver.

The analysis of this proposed rule is based on the fleet forecast for small unmanned aircraft as published in the FAA Aerospace Forecast.\9\ The forecast includes base, low, and high scenarios. This analysis provides a range of net impacts from low to high based on these forecast scenarios. The FAA considers the primary estimate of net impacts of the proposed rule to be the base scenario. For the primary estimate, over a 10-year period of analysis this proposed rule would result in net present value costs of about $582 million at a three percent discount rate with annualized net costs of about $68 million. At a seven percent discount rate, the net present value costs are about $474 million with annualized net costs of $67 million. The following table presents a summary of the primary estimates of the quantified costs and cost savings of this proposed rule. Additional details, including low and high estimates of quantified net costs, are provided in the Regulatory Evaluation section of this proposal and in the Preliminary Regulatory Impact Analysis available in the docket for this rulemaking.

\9\ FAA Aerospace Forecast Fiscal Years 2019-2039, available at https://www.faa.gov/data_research/aviation/aerospace_forecasts/media/FY2019-39_FAA_Aerospace_Forecast.pdf. The forecast provides a base (i.e., likely) with high (or optimistic) and low (or pessimistic) scenarios. The low and high forecast scenarios are not symmetric around the base--please see the forecast report for more information.

Table 2--Preliminary Estimates of Costs and Cost Savings of Proposed Rule ($Millions) * Base Scenario--Primary

Table 2--Preliminary Estimates of Costs and Cost Savings of Proposed Rule ($Millions) * Base Scenario--Primary

Estimate

10-year 10-year

Affected entity/category present value Annualized (at present value Annualized (at

(at 3%) 3%) (at 7%) 7%)

UAS Owners/Operators … $145.87 $17.10 $117.48 $16.73

Remote ID USS Subscription … 241.72 28.34 191.74 27.30

UAS Producers (US and Foreign) … 134.58 15.78 111.58 15.89

Developers of Remote ID Means of Compliance … 2.85 0.33 2.36 0.34

Remote ID USS Memoranda of Agreement … 1.60 0.19 1.43 0.20

Community Based Organizations … 0.39 0.05 0.35 0.05

FAA Costs … 56.96 6.68 50.33 7.17

Total Costs … 583.98 68.46 475.27 67.67

Cost Savings (reduced hours for FAA (2.45) (0.29) (1.82) (0.26)

investigations) …

Net Costs … 581.52 68.17 473.46 67.41

* Table notes: Column totals may not sum due to rounding and parenthesis, "( )", around numbers to indicate

* Table notes: Column totals may not sum due to rounding and parenthesis, "( )", around numbers to indicate

savings.

The FAA expects this proposed rule will result in several important benefits and enhancements to support the safe integration of expanded UAS operations in the airspace of the United States. The proposal would provide situational awareness of UAS operations to other aircraft and airport operators. The proposed rule would provide information to distinguish compliant UAS users from those potentially posing a safety or security risk. The following table summarizes the benefits of the proposed rule.

Table 3--Summary of Benefits of Proposed Rule

Safety and Security … • Provides situational awareness

of UAS flying in the airspace of the

United States to other aircraft in the

vicinity of those operations and airport

operators.

• Provides information to

distinguish compliant UAS users from

those potentially posing a safety or

security risk.

• Enables the FAA, national

security agencies, and law enforcement

entities to obtain situational awareness

of UAS in the airspace of the United

States in near real-time.

• Provides additional registration

and notification requirements for

identifying aircraft and promoting

accountability and the safe and

efficient use of the airspace of the

United States.

Enables Expanded Operations • Assists in the implementation of

and UAS Integration. operations of small UAS over people and

at night. A final rule for operation of

small UAS over people and at night is

contingent upon a final action for UAS

with remote identification being in

effect.

• Provides UAS-specific data to

facilitate future, more advanced

operational capabilities, such as detect-

and-avoid and aircraft-to-aircraft

communications that support beyond

visual line of sight (BVLOS) operations.

• Provides UAS-specific data to

develop a comprehensive UAS traffic

management (UTM) system that would

facilitate the safe expansion of

operations.

In addition, the proposed rule provides flexibility through minimum performance requirements that would accommodate future innovation and improve the efficiency of UAS operations. The proposal also does not preclude early compliance for UAS producers or operators to realize earlier expanded operations and commercial opportunities.

E. Structure of This Proposed Rule

E. Structure of This Proposed Rule

This proposed rule addresses remote identification of UAS from a number of perspectives: UAS owners, UAS operators, UAS designers and producers, developers of remote identification means of compliance, and Remote ID USS. The FAA recognizes that certain persons may only be interested in certain topics. Therefore, the following provides the structure of this proposed rule.

Section II of this preamble discusses the FAA's legal authority for promulgating this proposed rule.

Section III of this preamble discusses the integration of UAS into the airspace of the United States. The complexities surrounding the full integration of UAS into the airspace of the United States has led the FAA to engage in a phased, incremental, and risk-based approach to rulemaking based on the statutory authorities delegated to the agency.

Section IV of this preamble discusses the need for remote identification of UAS operating in the airspace of the United States. The section addresses the role of the FAA as the United States civil aviation authority and air navigation service provider, current registration requirements and how those requirements do not provide information responsive to remote identification, current cooperative surveillance for manned aircraft, and the need for situational awareness. The section further explains how remote identification of UAS fits within the FAA's compliance and enforcement programs. The section describes how the FAA envisions remote identification may facilitate beyond visual line of sight (BVLOS) operations in the future. The potential benefits of remote identification of UAS to national security and law enforcement agencies are noted.

Section V of this preamble discusses related international activities.

Section VI of this preamble provides a summary of the Unmanned Aircraft Systems (UAS) Identification (ID) and Tracking Aviation Rulemaking Committee (ARC) (UAS-ID ARC) report and the FAA's response to that report.

Section VII of this preamble discusses the new terms to be defined as part of this proposed rule.

Section VIII of this preamble describes the applicability of the proposed rule. It also discusses the framework of the following sections: Operating requirements for UAS with remote identification, means of compliance, and design and production requirements.

Section IX of this preamble discusses the current registration requirements for unmanned aircraft under part 47 and part 48 and the issues with the current registration requirements in light of the need for remote identification of UAS. The section also discusses the FAA's proposed revision of the registration requirements of part 48 to require the individual registration of unmanned aircraft and the proposed use of unmanned aircraft serial numbers as unique identifiers for remote identification purposes.

Section X of this preamble explains the operating requirements related to remote identification of UAS. It describes the requirements for standard remote identification UAS and limited remote identification UAS. It also discusses the proposed requirements for UAS without remote identification. The section provides the proposed requirements to transmit and broadcast, as appropriate, message elements. It discusses the FAA's proposal to prohibit the use of ADS-B Out to satisfy remote identification of UAS. Finally, it discusses UAS operators' requirement to operate a UAS with remote identification only if that UAS is listed on a valid FAA-accepted declaration of compliance.

Section XI of this preamble discusses law enforcement access to remote identification information.

Section XII of this preamble discusses the FAA's proposed requirements for what an FAA-accepted means of compliance for remote identification would contain. The FAA is proposing that any FAA-accepted means of compliance contain requirements regarding the message elements to be transmitted and the minimum performance requirements for the transmission and broadcast, as appropriate, of those elements. The section discusses the process to submit and have the FAA accept a means of compliance, and data retention requirements for submitters of means of compliance. The section also discusses other requirements the FAA considered in the development of this proposed rule.

Section XIII of this preamble provides the proposed design and production requirements. It discusses the proposed requirement that producers of standard remote identification UAS and limited remote identification UAS issue serial numbers for UAS and that persons producing UAS with remote identification would be required to do so in accordance with the minimum performance requirements of the proposed rule using an FAA-accepted means of compliance. The section also describes the requirement for producers to submit a declaration of compliance, followed by a description of the process for FAA acceptance of declarations of compliance, rescission of those declarations, and the right of a person who submitted the FAA-accepted declaration of compliance or any person adversely affected by the rescission of the Administrator's acceptance of a declaration of compliance to petition for reconsideration of a rescission. Finally, the section discusses data retention requirements for producers submitting FAA-accepted declarations of compliance.

Section XIV of this preamble discusses the role of Remote ID USS. The section describes the FAA's vision regarding the role of Remote ID USS in providing remote identification services as well as how they will be established and what data provided to them will be publicly available. The section also describes the FAA's vision for data privacy and information security.

Section XV of this preamble provides the overarching requirements for FAA-recognized identification areas to be used by UAS that cannot, or do not, comply with the proposed remote identification requirements.

Section XVI of this preamble discusses the circumstances under which the use of ADS-B Out and transponders for UAS would be prohibited.

Section XVII of this preamble provides the proposed effective dates and compliance dates.

Section XVIII of this preamble discusses the proposed guidance documents.

Sections XIX and XX of this preamble address the FAA's requirements to comply with various statutes and Executive Orders pertaining to all regulations.

Section XXI of this preamble discusses the tribal considerations related to this proposed rule.

Section XXII of this preamble discusses the privacy impact analysis the FAA conducted as part of this proposed rule.

Section XXIII of this preamble provides additional information to persons wishing to provide comments to this proposed rule.

II. Authority for This Rulemaking

II. Authority for This Rulemaking

The FAA's authority to issue rules on aviation safety is found in Title 49 of the United States Code (49 U.S.C.). Subtitle I, section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

This rulemaking is promulgated pursuant to 49 U.S.C. 40103(b)(1) and (2), which direct the FAA to issue regulations: (1) To ensure the safety of aircraft and the efficient use of airspace; and (2) to govern the flight of aircraft for purposes of navigating, protecting and identifying aircraft, and protecting individuals and property on the ground. In addition, 49 U.S.C. 44701(a)(5) charges the FAA with promoting safe flight of civil aircraft by prescribing regulations the FAA finds necessary for safety in air commerce and national security.

Section 2202 of Public Law 114-190 requires the Administrator to convene industry stakeholders to facilitate the development of consensus standards for remotely identifying operators and owners of UAS and associated unmanned aircraft and to issue regulations or guidance based on any standards developed.

The Administrator is granted the authority under 49 U.S.C. 44805 to establish a process for, among other things, accepting risk-based consensus safety standards related to the design and production of small UAS. Under 49 U.S.C. 44805(b)(7), one of the considerations the Administrator must take into account prior to accepting such standards is any consensus identification standard regarding remote identification of unmanned aircraft developed pursuant to section 2202 of Public Law 114-190.

Additionally, section 44809(f) of 49 U.S.C. provides that the Administrator is not prohibited from promulgating rules generally applicable to unmanned aircraft, including those unmanned aircraft eligible for the exception for limited recreational operations of unmanned aircraft. Among other things, this authority extends to rules relating to the registration and marking of unmanned aircraft and the standards for remotely identifying owners and operators of UAS and associated unmanned aircraft.

The FAA has authority to regulate registration of aircraft under 49 U.S.C. 44101-44106 and 44110-44113, which require aircraft to be registered as a condition of operation and establish the requirements for registration and registration processes.

Finally, this rulemaking is promulgated under the authority described in 49 U.S.C. 106(f), which establishes the authority of the Administrator to promulgate regulations and rules, and 49 U.S.C. 40101(d), which authorizes the FAA to consider in the public interest, among other things, the enhancement of safety and security as the highest priorities in air commerce, the regulation of civil and military operations in the interest of safety and efficiency, and assistance to law enforcement agencies in the enforcement of laws related to regulation of controlled substances, to the extent consistent with aviation safety.

III. Integration of UAS Into the Airspace of the United States

III. Integration of UAS Into the Airspace of the United States

The rapid proliferation of UAS has created significant opportunities and challenges for their integration into the airspace of the United States. The relatively low cost of highly capable UAS technology has allowed for hundreds of thousands of new operators to enter the aviation community.

The complexities surrounding the full integration of UAS into the airspace of the United States have led the FAA to engage in a phased, incremental, and risk-based approach to rulemaking based on the statutory authorities delegated to the agency. On December 16, 2015, the FAA and DOT jointly published an interim final rule in the Federal Register titled Registration and Marking Requirements for Small Unmanned Aircraft ("Registration Rule"),\10\ which provided for a web-based aircraft registration process for small unmanned aircraft in 14 CFR part 48, to serve as an alternative to the registration requirements for aircraft established in 14 CFR part 47. The Registration Rule imposed marking requirements on small unmanned aircraft registered under part 48 to display a unique identifier in a manner that is visible upon inspection. This unique identifier could be the registration number issued to an individual or to the aircraft by the FAA Registry or the small unmanned aircraft's serial number if authorized by the Administrator and provided with the application for the certificate of aircraft registration.

\10\ 80 FR 78594.

On June 28, 2016, the FAA and DOT jointly published the final rule for Operation and Certification of Small Unmanned Aircraft Systems ("The 2016 Rule") in the Federal Register.\11\ This was an important step towards the integration of civil small UAS operations (for aircraft weighing less than 55 pounds) into the airspace of the United States. The 2016 Rule set the initial operational structure and certain restrictions to allow routine civil operations of small UAS in the airspace of the United States in a safe manner. Prior to the 2016 Rule, the FAA authorized commercial UAS operations, including real estate photography, precision agriculture, and infrastructure inspection, under section 333 of Public Law 112-95. Over 5,500 operators received this authorization. The FAA also issued over 900 Certificates of Waiver or Authorization (COA), allowing Federal, State, and local governments, law enforcement agencies, and public universities to perform numerous tasks with UAS, including search-and-rescue, border patrol, and research. The 2016 Rule allows for certain operations of small UAS in the airspace of the United States without the need for airworthiness certification, exemptions, or certificates of waiver or authorization.

\11\ 81 FR 42064.

The 2016 Rule also imposed certain restrictions on small UAS operations. The restrictions include a prohibition on nighttime operations, limitations on operations conducted during civil twilight, restrictions on operations over people, a requirement for all operations to be conducted within visual line of sight, and other operational, airspace, and pilot certification requirements. Since the rule took effect on August 29, 2016, most low-risk small UAS operations that were previously authorized on a case-by-case basis under Public Law 112-95 section 333 are now considered routine operations. These operations are now permitted within the requirements of part 107 without further interaction with the FAA. Publishing Part 107 was the first significant regulatory step to enable lower risk, less complex UAS operations.

Part 107 opened the airspace of the United States to the vast majority of routine small UAS operations, allowing flight within visual line of sight while maintaining flexibility to accommodate future technological innovations. Part 107 allows individuals to request waivers from certain provisions, including those prohibiting operations over people and beyond visual line of sight. Petitions for waivers from the provisions of part 107 must demonstrate that the petitioner has provided sufficient mitigations to safely conduct the requested operation.

On October 5, 2018, Congress enacted Public Law 115-254, also known as the FAA Reauthorization Act of 2018. The FAA Reauthorization Act of 2018 amended Part A of subtitle VII of title 49, United States Code by inserting a new chapter 448 titled Unmanned Aircraft Systems and incorporating additional authorities and mandates to support the further integration of UAS into the airspace of the United States, including several provisions that specifically deal with the need for remote identification of UAS. Section 376 of the FAA Reauthorization Act of 2018 requires the FAA to perform testing of remote identification technology and to assess the use of remote identification for the development of UTM.

Additionally, congressional action supports the implementation of remote identification requirements for most UAS. Section 349 of the FAA Reauthorization Act of 2018 included a provision indicating that the Administrator is not prohibited from promulgating rules relating to the standards for remotely identifying owners and operators of UAS and associated unmanned aircraft.\12\ The provision denotes Congress's acknowledgment that remote identification is an essential part of the UAS regulatory framework. Section 349 also does not prohibit the Administrator from promulgating rules generally applicable to unmanned aircraft related to updates to the operational parameters for unmanned aircraft used for limited recreational operations, the registration and marking of unmanned aircraft, and other standards consistent with maintaining the safety and security of the airspace of the United States.\13\

\12\ See 49 U.S.C. 44809.

\13\ Id.

Lastly, on February 13, 2019, the FAA published three rulemaking documents in the Federal Register as part of the next phase for integrating small UAS into the airspace of the United States. The first of such documents was an interim final rule titled "External Marking Requirement for Small Unmanned Aircraft," \14\ in which the FAA required small unmanned aircraft owners to display the registration number assigned by the FAA on an external surface of the aircraft. The second rulemaking document was a notice of proposed rulemaking titled "Operation of Small Unmanned Aircraft Systems Over People," \15\ in which the FAA proposed to allow operations of small unmanned aircraft over people in certain conditions and operations of small UAS at night without obtaining a waiver. The third rulemaking document was an advance notice of proposed rulemaking titled "Safe and Secure Operations of Small Unmanned Aircraft Systems," \16\ in which the FAA sought information from the public on whether and under which circumstances the FAA should promulgate new rules to require stand-off distances, additional operating and performance restrictions, the use of UAS Traffic Management (UTM), additional payload restrictions, and whether the agency should prescribe design requirements and require that unmanned aircraft be equipped with critical safety systems.

\14\ 84 FR 3669.

\15\ 84 FR 3856.

\16\ 84 FR 3732.

IV. Need for Remote Identification of UAS Operating in the Airspace of the United States

A. Maintaining the Safety and Efficiency of the Airspace of the United States

The FAA is both the civil aviation authority and the air navigation service provider (ANSP) for the United States. The FAA has statutory responsibilities to set standards and certify aircraft, airmen, and facilities. In addition, the FAA is responsible for ensuring the safe and efficient use of navigable airspace. The FAA carries out its responsibilities by developing air traffic rules, assigning the use of airspace, and controlling air traffic through a complex network of airport towers, air route traffic control centers, and flight service stations.

A. Maintaining the Safety and Efficiency of the Airspace of the United States

The FAA is responsible for serving tens of thousands of commercial and private aircraft operating in 29 million square miles of airspace each day. Through its air traffic management (ATM) system, the FAA coordinates the movements of these aircraft to ensure they operate at safe distances from each other and manages disruptions to normal air traffic flow. The FAA's ability to manage air traffic in the airspace of the United States is predicated on the agency knowing who is operating in the airspace and, if necessary, on being able to communicate with those airspace users. 1. Existing Cooperative Surveillance System

The ATM system relies on appropriately equipped aircraft to provide the surveillance services necessary to ensure the safety and efficiency of the airspace of the United States. In addition to ground-based equipment such as primary and secondary radar, participating aircraft use ATC transponders and ADS-B Out to participate in the ATM's cooperative surveillance environment. Transponders emit a radio frequency response when they are interrogated by ground-based secondary radar systems. Part of the response is the Mode 3/A code which is a four digit number ranging from 0000 to 7777 that allows ATC to identify aircraft under radar surveillance and correlate the target to a flight plan. Other information provides ATC with the location of the aircraft, which is shown on ATC radar displays. After January 1, 2020, aircraft will be required to equip with ADS-B Out to operate in certain airspace.

Some UAS, such as those operating in Class A airspace, are already equipped with transponders and ADS-B Out and operate in accordance with existing rules. But for the majority of UAS, especially those operating at low altitudes, the existing cooperative surveillance system is not capable of providing the necessary services.

Currently, there is no regulatory requirement mandating the remote identification of unmanned aircraft other than the existing equipment rules in part 91 for transponders that are applicable to aircraft in certain airspace and ADS-B Out, which will be required for aircraft in certain airspace after January 1, 2020. Because the majority of UAS operations occur at low altitudes, the existing rules do not adequately provide for awareness of who is operating in the airspace. The FAA is therefore proposing to require the remote identification of UAS to enable the agency to identify unmanned aircraft flying in the airspace of the United States and locate the operators of those aircraft. Remote identification equipment would provide identifying information for UAS similar to how ADS-B and transponders provide identifying information for manned aircraft. This information would also be essential for the management of the flow of air traffic as more UAS integrate into the airspace of the United States.

The FAA does not propose the use of transponders or ADS-B Out for remote identification for three primary reasons. First, the use of these technologies would require significant additional infrastructure, including radars and receivers, to cover the lower altitudes of the airspace of the United States where unmanned aircraft are expected to primarily operate. Second, the FAA expects that, due to the volume of unmanned aircraft operations projected, the additional radio frequency signals would saturate the available spectrum and degrade the overall cooperative surveillance system. Finally, transponders and ADS-B Out do not provide any information about the location of control stations, as these systems were designed for manned aircraft. For these reasons, the FAA has determined that existing cooperative surveillance systems are incapable of supporting UAS remote identification and is proposing a new cooperative surveillance technology specifically for UAS. However, the proposal does not prohibit the use of ADS-B In, if the ADS-B In equipment is manufactured and installed in accordance with FAA requirements and guidance.\17\

\17\ See Advisory Circulars 20-172B and 90-114A.

2. Current Challenges With Associating UAS With Their Owners and Operators

All manned aircraft, unmanned aircraft weighing over 0.55 pounds, and any unmanned aircraft operated pursuant to 14 CFR part 107 or part 91 (irrespective of weight) are subject to FAA's aircraft registration and marking requirements. These requirements are the fundamental means for the FAA to physically identify manned and unmanned aircraft operating in the airspace of the United States and to associate them with their owners. The FAA recognizes that current registration and marking requirements are most useful when the aircraft is static or when information regarding the aircraft and its owner is needed without a direct link to the aircraft itself. In the case of unmanned aircraft in flight, however, registration and marking alone are insufficient to identify the aircraft and to locate the person manipulating the flight controls of a UAS. This is due to both the small size of most unmanned aircraft and to the fact that the person manipulating the flight controls of the UAS is not co-located with the aircraft. The Registration Rule acknowledged that the registration of small unmanned aircraft would provide a means by which to quickly identify the aircraft in the event of an incident or accident involving a small UAS. The Registration Rule also acknowledged that registration of small unmanned aircraft would provide an immediate and direct opportunity for the FAA to educate small UAS owners on safety requirements before they begin operating. The Registration Rule did not, however, envision the use of registration numbers as a means to identify or locate the small UAS owner or the person manipulating the flight controls of the UAS during real-time flight operations.

2. Current Challenges With Associating UAS With Their Owners and Operators

The small size of most unmanned aircraft makes it difficult--if not impossible--to read their registration numbers from the ground, preventing proper identification of the unmanned aircraft while it is in flight. Although it is true that manned aviation faces similar identification issues (since aircraft registration marks may be impossible to read from the ground when the aircraft is flying at certain altitudes or speeds), there is an important distinction between manned and unmanned aviation that makes the inability to read a registration number from the ground less problematic in manned aviation. In manned aviation, the pilot-in-command is co-located with the aircraft and is therefore more easily identifiable, even if such identification occurs after landing.

In addition, pilots of manned aircraft are often required to, or choose to, maintain two-way communications with air traffic control (ATC) for purposes of receiving air traffic services. This communication helps ascertain the identity and intent of the pilot in command. Furthermore, transponders and ADS-B Out systems transmit unique codes that allow ATC to identify and distinguish aircraft from others flying in the airspace of the United States, as discussed in the preceding section. These means of identification are not currently required or feasible for UAS. The challenge of identifying UAS would only increase with the proliferation of BVLOS operations--when pilots will likely be located far away from the unmanned aircraft location. 3. Situational Awareness

The ability to know the location of unmanned aircraft operating in the airspace of the United States and to identify and locate their operators creates situational awareness of operations conducted in the airspace of the United States, fosters accountability of the operators and owners of UAS, and improves the capabilities of the FAA and law enforcement to investigate and mitigate careless, hazardous, and noncompliant operations. This contributes to safety in air commerce and the efficient use of the airspace of the United States.

Remote identification would provide greater situational awareness of UAS operating in the airspace of the United States to other aircraft in the vicinity of those operations and also provide information to airport operators. Manned aircraft, especially those operating at low altitudes where UAS operations are anticipated to be the most prevalent, such as helicopters and agricultural aircraft, could carry the necessary equipment to display the location of UAS operating nearby. Facility operators could use remote identification information to know about UAS operating near an airport, airfield, or heliport, regardless of the airspace in which the facility is located. This would provide a level of awareness that is currently unavailable for those facilities and the aircraft operating nearby. For example, an aircraft preparing to take off from an airport in Class G airspace may have access to greater information (e.g., number and location of UAS, types of operations conducted in the airspace, etc.) than currently available. 4. Compliance and Enforcement

The safety of the airspace of the United States largely depends on aircraft operators following the prescribed rules and being accountable for their actions. The FAA needs the ability to identify aircraft and their owners to ensure adequate oversight of the operations (e.g., facilitate the identification of noncompliant or unauthorized operations). When unsafe operations are discovered, the FAA is required to adequately address safety issues that may adversely affect the airspace of the United States as well as people and property on the ground. To accomplish this, the FAA needs a means to locate UAS operators--in near real-time, if necessary--to take immediate or subsequent action to mitigate safety issues or security threats. Thus, the FAA believes that the remote identification requirements in this proposed rule are necessary to ensure the safety of the airspace of the United States.

If an operator is unwilling or unable to comply with, or is deliberately flouting regulations, the FAA could employ legal enforcement action, including civil penalties and certificate actions, as appropriate, to address violations and help deter future violations. Civil penalties for violations of the federal aviation regulations range from a maximum per violation penalty of $1,466, for individual operators, to $33,333 for large companies. In addition, Congress granted the FAA authority to assess civil penalties of up to $20,000 against an individual who operates a UAS and in so doing knowingly or recklessly interferes with a law enforcement, emergency response, or wildfire suppression activity. The FAA may take enforcement action against anyone who conducts an unauthorized UAS operation or operates a UAS in a way that endangers the safety of the airspace of the United States. This authority is designed to protect users of the airspace as well as people and property on the ground.

B. Unmanned Aircraft Systems Traffic Management (UTM)

B. Unmanned Aircraft Systems Traffic Management (UTM)

The FAA, in an effort to further integrate UAS into the airspace of the United States, is collaborating with other government agencies and industry stakeholders to develop unmanned aircraft systems traffic management (UTM) separate from, but complementary to, the ATM system. The term "UTM" refers to a set of third-party services and an all-encompassing framework for managing multiple UAS operations. This vision for UTM includes services for flight planning, communications, separation, and weather, among others. The FAA believes that remote identification facilitates the long-term implementation of UTM by providing greater awareness of all aircraft, including unmanned aircraft, operating in a particular area. UTM would help enable increased UAS operations in both controlled and uncontrolled airspace, including airspace where no air traffic separation services are currently provided.

The vision for UTM \18\ relies on third parties' ability to supply services, under FAA's regulatory authority, where such services do not currently exist. The FAA envisions community-based traffic management, where UAS operators have the responsibility for the coordination, execution, and management of a safe operating environment. UTM would be designed to support the demand and expectations for a broad spectrum of UAS operations with ever-increasing complexity and risk.

\18\ https://utm.arc.nasa.gov/docs/2018-UTM-ConOps-v1.0.pdf

The concept of UTM is predicated on layers of information sharing and exchange, from operator to operator, aircraft to aircraft, and operator to the FAA, to achieve safe operations. Operators would share their flight intent with each other and coordinate to de-conflict and safely separate trajectories. Remote identification is a crucial first step in the development of these UTM services.

C. Facilitating Beyond Visual Line of Sight Operations

C. Facilitating Beyond Visual Line of Sight Operations

Providing a means to conduct routine BVLOS operations is a critical step in the integration of UAS operations in the airspace of the United States. The technologies and procedures necessary to enable BVLOS operations have been the focus of past and current research by the FAA and others.\19\ The research indicated that for UAS to conduct safe, routine BVLOS operation, UAS should be able to detect both cooperative and non-cooperative aircraft (manned and unmanned) so they can maintain a safe distance from those aircraft. Cooperative aircraft are those that are providing information that identifies the location of the aircraft, typically through a standardized and receivable electronic radio frequency broadcast or other type of transmission. Non-cooperative aircraft are those that are not providing any information regarding their location.

\19\ https://www.faa.gov/uas/programs_partnerships/integration_pilot_program/; https://www.faa.gov/uas/programs_partnerships/completed/; http://www.assureuas.org/projects/detectandavoid.php

A UAS that broadcasts or transmits remote identification information would contribute to a cooperative operating environment. Operators of UAS could use remote identification information available from a Remote ID USS or broadcast directly from other unmanned aircraft to know the location of UAS operating nearby. Such data could be used in UAS detect-and-avoid and aircraft-to-aircraft communication systems to aid in unmanned aircraft collision avoidance. Under UTM, when the locations of other unmanned aircraft become known, the UAS operators would be able to maintain a safe distance from those aircraft.

Although remote identification of UAS does not, in and of itself, permit BVLOS operations, it is a key stepping stone to the future ability to conduct those operations. Without remote identification of UAS, BVLOS operations on a large scale are not feasible, and the foundational building blocks of UTM--which is necessary to enable routine BVLOS operations--are not established.

D. National Security and Law Enforcement Efforts

D. National Security and Law Enforcement Efforts

This proposed rule would serve the public interest by assisting government efforts to address illegal activity and protect national security. The safety and security benefits described in this section are consistent with the FAA's responsibilities to assist law enforcement agencies in their efforts to enforce laws related to regulation of controlled substances, to the extent consistent with aviation safety,\20\ and to prescribe regulations necessary for safety in air commerce and national security.\21\

\20\ 49 U.S.C. 40101(d).

\21\ 49 U.S.C. 44701(a)(5).

Federal, State, and local law enforcement and national security agencies have expressed their desire for new regulations to reduce and address the security threats associated with illegal or threatening UAS operations as well as the ability to discriminate between compliant and non-compliant operations. The FAA recognizes the increasing availability and potential use of UAS for illegal activities such as the carrying and smuggling of controlled substances, illicit drugs, and other dangerous or hazardous payloads; the unlawful invasion of privacy; illegal surveillance and reconnaissance; the weaponization of UAS; sabotaging of critical infrastructure; property theft; disruption; and harassment. The misuse of UAS for these purposes presents a direct threat to public safety. Such misuse also presents a hazard to safety in air commerce. Such risks are multiplied with the increasing sophistication of technology, the availability of UAS equipment, and the proliferation of UAS operations across the airspace of the United States.

Unmanned aircraft operators who know they cannot easily be identified are more likely to engage in careless, reckless, or dangerous behavior because they believe they will not be caught. These operators could engage in evasive maneuvering to avoid pursuit, violate airspace restrictions, engage in unauthorized night or BVLOS operations, fly too close to other aircraft, or operate in weather conditions beyond the capability of the unmanned aircraft or the person flying it. Such behavior could create severe safety hazards not only to other manned and unmanned aircraft in the surrounding airspace, but also to persons and property on the ground.

Additionally, UAS operators that do not comply with applicable law create a unique security challenge. On average, six sightings of UAS allegedly conducting unauthorized operations are reported to the FAA each day. Additionally, based on information provided by other U.S. Government agencies, there may be many additional UAS sightings involving unauthorized or illegal operations not reported to the FAA. Although collisions with aircraft are rare, there have been two confirmed unmanned aircraft collisions with manned aircraft: an Army Blackhawk helicopter in New York City in September 2017, and a small twin-engine passenger aircraft approaching Quebec City's Jean Lesage International Airport in October 2017. In all of these circumstances, remote identification could have enabled immediate identification of the UAS and enabled law enforcement to find the location of the control station for near real-time response and investigation.

Owners of critical infrastructure, airports, and venues for mass gatherings have expressed concern over the security of their facilities after sightings of UAS of unknown identity and intent. Many sightings are at night, when it may be more difficult to see and identify the unmanned aircraft or find the operator. Owners and facility managers of sports stadiums and other open-air venues are particularly concerned, given the concentration of people present during an event. Malicious UAS activities designed to disrupt and gain media attention are a distinct threat with the potential to inflict delays, fear, injuries, and significant economic losses across a variety of critical infrastructure sectors, including airports, public facilities, and energy production infrastructure.

On April 11, 2019, numerous spectators visually spotted a UAS operating during a Major League Baseball game.\22\ Although law enforcement were able to eventually identify the operator within 24 hours due to a municipally-owned detection system, remote identification would likely have allowed them to find the operator and control station much more quickly and address the issue in real time. After law enforcement confiscated the UAS involved in the April 2019 incident and were able to review its flight log, they learned that the operator had flown over a previous World Series game at the same stadium--violating an FAA Temporary Flight Restriction and numerous safety regulations.

\22\ https://www.usatoday.com/story/sports/mlb/redsox/2019/04/13/drone-fenway-park-juvenile/3457190002/. Accessed June 11, 2019.

A UAS that was not approved to operate over people was used to drop pamphlets over large crowds outside a concert venue and a university event in May, 2019, in Sacramento, California.\23\ This event was similar to two incidents in 2017 when a UAS was used to drop leaflets at two California National Football League games.\24\ Although security and law enforcement personnel at the stadium used rudimentary tactics to eventually identify the accused operator, the lack of remote identification made real-time location of the operator impossible.\25\ Security professionals have raised concerns that unmanned aircraft that have not been determined to be safe to fly over a large gathering of people may pose a safety hazard, and a UAS dropping objects could potentially pose a greater threat by releasing hazardous substances or creating a stampede of frightened spectators fleeing the area. Although social media postings helped identify the operator in some cases, such information rarely helps law enforcement officers address a potential threat in real time.

\23\ https://www.newsweek.com/drone-used-drop-nazi-leaflets-ariana-grande-concert-sacramento-bites-bridge-1414933. Accessed June 11, 2019.

\24\ https://www.justice.gov/usao-ndca/pr/sacramento-area-resident-charged-flying-drone-over-nfl-games-violation-national-defense. Accessed June 10, 2019.

\25\ Id.

Multiple pilot reports of a UAS approximately 10 miles away from Newark Airport led to a disruption in arrivals in January 2019 that impacted other airports on the East Coast for several hours.\26\ The more than 30-hour disruption of flights at London's Gatwick Airport in December 2018,\27\ as well as brief disruptions at airports in Dubai,\28\ Dublin,\29\ and Frankfurt \30\ within the last year, further demonstrate the potential for significant operational and financial impact from the presence of an unauthorized UAS in and around an airport. UAS operators have not been identified in any of these airport events. Remote identification of UAS would potentially prevent disruptions such as these by enabling real time action by the FAA, airport facilities, and law enforcement.

\26\ https://www.washingtonpost.com/transportation/2019/01/22/drone-activity-halts-air-traffic-newark-liberty-international-airport/?noredirect=on&utm_term=.c0e920a9e756. Accessed June 11, 2019.

\27\ https://www.theguardian.com/uk-news/2018/dec/21/gatwick-airport-reopens-limited-number-of-flights-drone-disruption. Accessed June 11, 2019.

\28\ http://www.digitaljournal.com/tech-and-science/technology/q-a-recent-airport-shutdowns-need-drone-interdiction-technology/article/543680. Accessed June 11, 2019.

\29\ https://dronelife.com/2019/02/22/flights-were-grounded-at-dublin-airport-after-another-drone-sighting/. Accessed June 11, 2019.

\30\ https://www.ecnmag.com/news/2019/03/drone-sightings-interrupt-germanys-frankfurt-airport. Accessed June 10, 2019.

Continue reading ↓ 120 of 673 passages shown