Radar Vectors
Final Rule Current Issued May 11, 2018 6 pages Copy saved Nov 17, 2026

83 FR 21850 Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

This document announces the availability of 63 Means of Compliance (MOC) based on 30 published ASTM International (ASTM) consensus standards developed by ASTM Committee F44 on General Aviation Aircraft. A total of 46 of these accepted MOCs consist of ASTM consensus standards as published, with the remaining 17 MOCs comprised of a combination of ASTM standards and FAA changes. The Administrator finds these MOCs to be an acceptable means, but not the only means, of showing compliance to the applicable regulations in part 23, amendment 23-64, for normal category airplanes. The Administrator further finds that these accepted means of complying with part 23, amendment 23-64, provide at least the same level of safety as the corresponding requirements in part 23, amendment 23-63.

Official source ↗ Official PDF ↗

14 CFR Part 23

[Notice No. 23-18-01-NOA]

Accepted Means of Compliance; Airworthiness Standards: Normal Category Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notification of availability; request for comments.

SUMMARY: This document announces the availability of 63 Means of Compliance (MOC) based on 30 published ASTM International (ASTM) consensus standards developed by ASTM Committee F44 on General Aviation Aircraft. A total of 46 of these accepted MOCs consist of ASTM consensus standards as published, with the remaining 17 MOCs comprised of a combination of ASTM standards and FAA changes. The Administrator finds these MOCs to be an acceptable means, but not the only means, of showing compliance to the applicable regulations in part 23, amendment 23-64, for normal category airplanes. The Administrator further finds that these accepted means of complying with part 23, amendment 23-64, provide at least the same level of safety as the corresponding requirements in part 23, amendment 23-63.

Dates

DATES: Comments must be received on or before July 10, 2018.

ADDRESSES: Mail comments to: Federal Aviation Administration, Policy and Innovation Division, Small Airplane Standards Branch, AIR-690, Attention: Steve Thompson, 901 Locust Street, Room 301, Kansas City, Missouri 64106. Comments may also be emailed to: [email protected]. Specify the MOC, and if applicable, the standard being addressed by designation and title. Mark all comments: Part 23 MOC Comments.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Steve Thompson, Federal Aviation Administration, Policy and Innovation Division, Small Airplane Standards Branch, AIR-690, 901 Locust Street, Room 301, Kansas City, Missouri 64106; telephone (816) 329-4126; facsimile: (816) 329-4090; email: [email protected].

Supplementary Information

SUPPLEMENTARY INFORMATION:

Comments Invited

Interested persons are invited to submit written comments, data, or views. Communications should identify the MOC and consensus standard number, where applicable, and be submitted to the address previously specified in the ADDRESSES section of this NOA. The most helpful comments reference a specific portion of the accepted MOC(s) or standard(s), explain the reason for any recommended change, and include supporting data. The FAA may forward communications regarding the consensus standards to ASTM Committee F44 for consideration. The MOC or standard may be revised based on received comments. The FAA will consider all comments received during the recurring review of the MOC and consensus standard and will participate in the consensus standard revision process.

Background

Background

Under the provisions of the National Technology Transfer and Advancement Act of 1995 \1\ and Office of Management and Budget (OMB) Circular A-119, "Federal Participation in the Development and Use of Voluntary Consensus Standards and in Conformity Assessment Activities," effective January 27, 2016, the FAA participates in the development of consensus standards and uses consensus standards as a means of carrying out its policy objectives where appropriate.

\1\ Ref Public Law 104-113 as amended by Public Law 107-107.

Consistent with the Small Airplane Revitalization Act of 2013,\2\ the FAA has been working with industry and other stakeholders through ASTM to develop consensus standards for use as a MOC in certificating small airplanes under part 23. In promulgating part 23, amendment 23-64, the FAA explained that if it determined such consensus standards were acceptable MOC to part 23, it would publish a notice of availability of those consensus standards in the Federal Register.

\2\ Ref Public Law 113-53.

Pursuant to FAA Advisory Circular 23.2010-1, section 3.1.1, this document serves as a formal acceptance by the Administrator, of MOCs based on consensus standards developed by ASTM. The MOCs accepted by this document are one means, but not the only means of complying with part 23 regulatory requirements.

The FAA has reviewed the consensus standards referenced in this NOA as the basis for MOCs to the regulatory requirements of part 23, amendment 23-64. In some cases, the Administrator finds sections of ASTM Standard F3264-17, "Standard Specification for Normal Category Aeroplanes Certification," without changes, are accepted as means of complying with the airworthiness requirements of part 23, without degrading safety, and within the scope and applicability of the consensus standards. In other cases, the MOCs, while based on ASTM consensus standards, include additional FAA provisions necessary to comply with the airworthiness requirements of part 23, amendment 23-64.

Part 23, amendment 23-64, established airworthiness requirements based on the level of safety of amendment 23-63 regulations, except for areas addressing loss of control and icing where the safety level was increased.\3\ Achieving this level of safety through compliance with amendment 23-64--for a given certification project--may require use of additional MOCs beyond those accepted by this document, depending on the details of the specific design. For example, an applicant's design may include features that are customary, but not addressed in the MOCs accepted by this document. Designs may also include features that are innovative and not type certificated previously. In either case, a supplemental MOC beyond those accepted in this document would be required. For example, the MOCs accepted by this document do not contain provisions addressing powered-trim system runaways. Therefore, in order to maintain the level of safety of amendment 23-63 regulations, applicants proposing use of these MOCs for an airplane with a powered-trim system would need to supplement the accepted MOC(s) with additional means for § 23.2300 to demonstrate safe controllability after a probable trim system runaway. To do this, applicants could use the provisions of § 23.677(d), amendment 23-49, or other MOC(s) accepted under § 23.2010. Further information on supplemental MOCs is provided in a part 23 means of compliance summary table and in the Small Airplanes Issues List, which are available on the Small Airplanes--Regulations, Policies & Guidance website.\4\

\3\ Ref 81 FR 96572, December 30, 2016.

\4\ See https://www.faa.gov/aircraft/air_cert/design_approvals/small_airplanes/small_airplanes_regs/.

Means of Compliance Accepted in This Document

The following is a list of sections from part 23, amendment 23-64, followed by their corresponding MOC accepted by this document: 23.1457: ASTM F3264-17, section 9.12 23.1459: ASTM F3264-17, section 9.13 23.1529: ASTM F3264-17, section 10.6

Subpart B--Flight

Subpart B--Flight

23.2100: ASTM F3264-17, section 5.1 23.2105: ASTM F3264-17, section 5.2 23.2110: ASTM F3264-17, section 5.3 23.2115: ASTM F3264-17, section 5.4 23.2120: ASTM F3264-17, section 5.5 23.2125: ASTM F3264-17, section 5.6 23.2130: ASTM F3264-17, section 5.7 23.2135: ASTM F3264-17, section 5.8, combined with the changes in the following table:

Replace: With:

ASTM F3173/F3173M-17, Sections 4.9.1.1 and 4.9.1.2... FAA 4.9.1.1 and

ASTM F3173/F3173M-17, Sections 4.9.1.1 and 4.9.1.2... FAA 4.9.1.1 and

4.9.1.2:

4.9.1.1: "For a

level 1 or 2

airplane, or

level 3 or 4

airplane of

6,000 pounds or

less maximum

weight, 5

seconds from

initiation of

roll and"

4.9.1.2: "For

a level 3 or

4 airplane of

over 6,000

pounds

maximum

weight,

(W+500)/1300

seconds, but

not more than

10 seconds,

where W is

the weight in

pounds." ASTM F3173/F3173M-17, Sections 4.9.3.1 and 4.9.3.2... FAA 4.9.3.1 and

4.9.3.2:

4.9.3.1: "For a

level 1 or 2

airplane, or

level 3 or 4

airplane of

6,000 pounds or

less maximum

weight, 4

seconds from

initiation of

roll and"

4.9.3.2: "For

a level 3 or

4 airplane of

over 6,000

pounds

maximum

weight,

(W+2,800)/

2,200

seconds, but

not more than

7 seconds,

where W is

the weight in

pounds."

23.2140: ASTM F3264-17, section 5.9 23.2145: ASTM F3264-17, section 5.10 23.2150: ASTM F3264-17, section 5.11 23.2155: ASTM F3264-17, section 5.12 23.2160: ASTM F3264-17, section 5.13 23.2165: ASTM F3264-17, section 5.14

Subpart C--Structures

Subpart C--Structures

23.2200: ASTM F3264-17, Section 6.1, combined with the changes in the following table:

Replace: With:

ASTM F3116/F3116M-15, Section 5.1.3.1(1) … FAA 5.1.3.1(1):

"VS is a 1g

computed

stalling speed

with flaps

retracted

(normally based

on the maximum

airplane normal

force

coefficient,

CNA) at the

design maximum

takeoff

weight."

23.2210: ASTM F3264-17, section 6.3 23.2215: ASTM F3264-17, section 6.4, combined with the changes in the following table:

Replace: With:

ASTM F3116/F3116M-15, Section 4.1.4 … FAA 4.1.4:

"Appendix X1

through appendix

X4 provide,

within the

limitations

specified within

the appendix, a

simplified means

of compliance

with several of

the requirements

set forth in 4.2

to 4.26 and 7.1

to 7.9 that can

be applied as

one (but not the

only) means to

comply. If the

simplified

methods in

appendix X1

through appendix

X3 are used,

they must be

used together in

their

entirety."

ASTM F3116/F3116M-15, Section 4.10.1.1 … FAA 4.10.1.1:

"In condition A,

assume 100% of

the semispan

wing airload

acts on one side

of the airplane

and 75% of this

load acts on the

other side. For

airplanes with

maximum weight

of 1,000 pounds

or less, 70% of

the load acts on

the other

side."

ASTM F3116/F3116M-15, Section X1.1.1 … FAA X1.1.1:

"The methods

provided in this

appendix provide

one possible

means (but not

the only

possible means)

of compliance

and can only be

applied to low-

speed, level 1

and level 2

airplanes."

ASTM F3116/F3116M-15, Section X1.1.4 … X1.1.4 through

X1.1.4.5: Same

as published in

F3116/F3116M-15.

Add FAA X1.1.4.6:

"Wings with

winglets, tip

tanks, or tip

fins."

23.2220: ASTM F3264-17, section 6.5 23.2225: ASTM F3264-17, section 6.6, combined with the changes in the following table:

Replace: With:

ASTM F3116/F3116M-15, Section X2.1.1 … FAA X2.1.1:

"The methods

provided in this

appendix provide

one possible

means (but not

the only

possible means)

of compliance

and can only be

applied to low-

speed, level 1

and level 2

airplanes."

ASTM F3116/F3116M-15, Section X3.1.1 … FAA X3.1.1:

"The methods

provided in this

appendix provide

one possible

means (but not

the only

possible means)

of compliance

and can only be

applied to low-

speed, level 1

and level 2

airplanes."

ASTM F3116/F3116M-15, Section X4.1.1 … FAA X4.1.1:

"The methods

provided in this

appendix provide

one possible

means (but not

the only

possible means)

of compliance

and can only be

applied to low-

speed, level 1

airplanes."

23.2230: ASTM F3264-17, section 6.7 23.2235: ASTM F3264-17, section 6.8, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 6.8.1 … FAA 6.8.1:

"F3114-15

Standard

Specification

for

Structures".

23.2240: ASTM F3264-17, section 6.9, combined with the changes in the following table:

Replace: With:

ASTM F3115/F3115M-15, Section 4.4.1 … FAA 4.4.1:

"For metallic

(aluminum),

unpressurized,

non-aerobatic,

low-speed, level

1 airplanes,

applicants can

demonstrate a

10,000 hour safe-

life by limiting

the `1g' gross

stress, at

maximum takeoff

weight, to no

more than 5.5

ksi. The

applicant must

show effective

stress

concentration

factors of 4 or

less in highly

loaded joints

and use

materials or

material systems

for which the

physical and

mechanical

properties are

well

established."

ASTM F3115/F3115M-15, Section 6.1 … FAA 6.1:

"For bonded

airframe

structure, the

residual

strength of

bonded joints

shall be

addressed as

follows: For any

bonded joint,

the failure of

which would

result in

catastrophic

loss of the

airplane, the

limit load

capacity must be

substantiated by

one of the

following

methods."

23.2245: ASTM F3264-17, section 6.10 23.2250: ASTM F3264-17, section 6.11 23.2255: ASTM F3264-17, section 6.12 23.2260: ASTM F3264-17, section 6.13 23.2265: ASTM F3264-17, section 6.14 23.2270: ASTM F3264-17, section 6.15

Subpart D--Design and Construction

Subpart D--Design and Construction

23.2300: ASTM F3264-17, section 7.1, combined with the changes in the following table:

Replace: With:

ASTM F3232/F3232M-17, Table 1, Row 4.4.6 … FAA Table 1, Row

4.4.6:

A white circle

("o") in the

following

Aircraft Type

Code (ATC)

character

fields:

"Airworthiness

Level--1" and

"Stall Speed--

L"; a mark-out

("x") in the

following ATC

character field:

"Number of

Engines--M";

and no codes in

any other ATC

character field.

Note: This change

applies the

standard of ASTM

F3232/F3232M-17,

Section 4.4.6,

to all single-

engine airplanes

except level 1

airplanes with a

stall speed of

45 knots or

less.

23.2305: ASTM F3264-17, section 7.2 23.2315: ASTM F3264-17, section 7.4 23.2320: ASTM F3264-17, section 7.5 23.2325: ASTM F3264-17, section 7.6, combined with the changes in the following table:

Replace: With:

ASTM F3061/F3061M-17, Section 10.3.2 … FAA 10.3.2:

"In each area

where flammable

fluids or vapors

might escape by

leakage of a

fluid system,

there must be

means to

minimize the

probability of

ignition of the

fluids and

vapors, and the

resultant hazard

if ignition does

occur. These

means must

account for the

factors

prescribed in

10.3.3 through

10.3.7."

23.2330: ASTM F3264-17, section 7.7 23.2335: ASTM F3264-17, section 7.8

Subpart E--Powerplant

23.2400: ASTM F3264-17, section 8.1, combined with the changes in the following table:

Subpart E--Powerplant

Replace: With:

ASTM F3065/F3065M-15, Section 4.3 … An FAA-accepted

means of

compliance for

Sec.

23.2400(c), such

as the

provisions of

Sec.

23.905(d),

amendment 23-59.

23.2405: ASTM F3264-17, section 8.2 23.2410: ASTM F3264-17, section 8.3, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 8.3 … 8.3 through

8.3.2: Same as

published in

F3264-17.

Renumber 8.3.3 to

8.3.6.

Add FAA 8.3.3

through 8.3.5,

and FAA 8.3.7:

8.3.3: "F3063/

F3063M--16a

Standard

Specification

for Design and

Integration of

Fuel/Energy

Storage and

Delivery System

Installations

for

Aeroplanes".

8.3.4: "F3064/

F3064M--15

Standard

Specification

for Control,

Operational

Characteristi

cs and

Installation

of

Instruments

and Sensors

of Propulsion

Systems".

8.3.5: "F3065/

F3065M--15

Standard

Specification

for

Installation

and

Integration

of Propeller

System".

8.3.7:

"F3117--15

Standard

Specification

for Crew

Interface in

Aircraft".

23.2415: ASTM F3264-17, section 8.4, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 8.4 … 8.4 through

8.4.1: Same as

published in

F3264-17.

Renumber 8.4.2 to

8.4.3.

Add FAA 8.4.2:

F3063/F3063M--

"16a Standard

Specification

for Design and

Integration of

Fuel/Energy

Storage and

Delivery System

Installations

for

Aeroplanes".

ASTM F3066/F3066M-15, Section 5.1 … An FAA-accepted

means of

compliance for

the induction

system ice

protection

aspects of Sec.

23.2415, such

as the

provisions of

Sec.

23.1093(a),

amendment 23-51.

ASTM F3066/F3066M-15, Section 5.2.1.1 … FAA 5.2.1.1:

"Operate

throughout its

flight power

range, including

minimum descent

idle speeds, in

the icing and

snow conditions

specified in

Specification

F3120/F3120M,

without the

accumulation of

ice on engine,

inlet system

components, or

airframe

components that

would do any of

the following:"

ASTM F3066/F3066M-15, Section 5.2.2 … [Remove]

ASTM F3066/F3066M-15, Sections 5.2.3, 5.2.3.1, and FAA 5.2.2:

5.2.3.2. "Each turbine

engine must idle

for 30 min on

the ground, with

the air bleed

available for

engine icing

protection at

its critical

condition,

without adverse

effect, in the

ground icing

conditions

specified in

Specification

F3120/F3120M."

FAA 5.2.2.1

Followed by

momentary

operation at

takeoff power or

thrust.

FAA 5.2.2.2

During the 30

min of idle

operation, the

engine may be

run up

periodically to

a moderate power

or thrust

setting."

23.2420: ASTM F3264-17, section 8.5, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 8.5 … 8.5 through

8.5.1: Same as

published in

F3264-17.

Remove 8.5.2 and

8.5.3.

Add FAA 8.5.2:

F3065/F3065M--

"15 Standard

Specification

for Installation

and Integration

of Propeller

System".

23.2425: ASTM F3264-17, section 8.6, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 8.6 … 8.6 through

8.6.2: Same as

published in

F3264-17.

Renumber 8.6.3 to

8.6.4.

Add FAA 8.6.3 and

FAA 8.6.5:

8.6.3: "F3065/

F3065M--15

Standard

Specification

for

Installation

and

Integration

of Propeller

System".

8.6.5:

"F3117--15

Standard

Specification

for Crew

Interface in

Aircraft".

23.2430: ASTM F3264-17, section 8.7, combined with the changes in the following table:

Replace: With:

ASTM F3264-17, Section 8.7 … 8.7.1 through

8.7.5: Same as

published in

F3264-17.

Add an FAA-

accepted means

of compliance

for the fuel

supply aspects

of Sec.

23.2430, such as

the provisions

of Sec.

23.991(b),

amendment 23-43.

ASTM F3066/F3066M-15, Section 6.3 … An FAA-accepted

means of

compliance for

the fuel/oil

tank aspects of

§ 23.2430,

such as the

provisions of

Sec.

23.967(d),

amendment 23-43.

23.2435: ASTM F3264-17, section 8.8 23.2440: ASTM F3264-17, section 8.9, combined with the changes in the following table:

Replace: With:

ASTM Section 8.9, F3264-17 … 8.9 through

8.9.2: Same as

published in

F3264-17.

Renumber 8.9.3 to

8.9.4.

Renumber 8.9.4 to

8.9.5 and change

to, "F3066/

F3066M-15

Standard

Specification

for Powerplant

Systems Specific

Hazard

Mitigation."

Add FAA 8.9.3:

8.9.3: "F3063/

F3063M-16a

Standard

Specification

for Design

and

Integration

of Fuel/

Energy

Storage and

Delivery

System

Installations

for

Aeroplanes."

Subpart F--Equipment

Subpart F--Equipment

23.2500: ASTM F3264-17, section 9.1 23.2505: ASTM F3264-17, section 9.2 23.2510: ASTM F3264-17, section 9.3 23.2515: ASTM F3264-17, section 9.4 23.2520: ASTM F3264-17, section 9.5 23.2525: ASTM F3264-17, section 9.6 23.2530: ASTM F3264-17, section 9.7 23.2535: ASTM F3264-17, section 9.8 23.2540: ASTM F3264-17, section 9.9 23.2545: ASTM F3264-17, section 9.10 23.2550: ASTM F3061/F3061M-17, section 10.9

Subpart G--Flightcrew Interface and Other Information

Subpart G--Flightcrew Interface and Other Information

23.2600: ASTM F3264-17, section 10.1, combined with the changes in the following table:

Replace: With:

ASTM Section 10.1, F3264-17 … 10.1.1 through

10.1.5: Same as

published in

F3264-17.

Add an FAA-

accepted means

of compliance

for the

windshield

luminous

transmittance

aspects of Sec.

23.2600, such

as the

provisions of

Sec.

23.775(e),

amendment 23-49.

Add an FAA-

accepted means

of compliance

for the pilot

compartment view

with formation

of fog or frost

aspects of Sec.

23.2600, such

as the

provisions of

Sec.

23.773(b),

amendment 23-45.

23.2605: ASTM F3264-17, section 10.2 23.2610: ASTM F3264-17, section 10.3 23.2615: ASTM F3264-17, section 10.4, combined with the changes in the following table:

Replace: With:

ASTM Section 6, F3064/F3064M-15 … An FAA-accepted

means of

compliance for

the powerplant

instruments

aspects of Sec.

23.2615, such

as the

provisions of

§ 23.1305,

amendment 23-52.

23.2620: ASTM F3264-17, sections 5.15 and 10.5

23.2620: ASTM F3264-17, sections 5.15 and 10.5

Editorial, Reapproval, Revision Or Withdrawal

The FAA expects a suitable consensus standard to be reviewed periodically. ASTM policy is that a consensus standard should be reviewed in its entirety by the responsible subcommittee and must be balloted for reapproval, revision, or withdrawal, within five years of its last approval date. ASTM reapproves a standard--denoted by the year of reapproval in parentheses (e.g., F2427-05a(2013))--to indicate completion of a review cycle with no technical changes made to the standard. ASTM issues editorial changes--denoted by a superscript epsilon in the standard designation (F3235-17 [egr]\1\)--to correct information that does not change the meaning or intent of a standard. Any MOC accepted by this document that is based on a standard later reapproved or editorially changed is also considered accepted without the need for a NOA. ASTM revises a standard to make changes to its technical content. Revisions to consensus standards serving as the basis for MOC accepted by this document will not be automatically accepted and will require further FAA acceptance in order for the revisions to be an accepted MOC.

Availability

Availability

ASTM Standard F3264-17, "Standard Specification for Normal Category Aeroplanes Certification," is available for online reading at https://www.astm.org/READINGLIBRARY/. ASTM International copyrights these consensus standards and charges the public a fee for service. Individual downloads or reprints of a standard (single or multiple copies, or special compilations and other related technical information) may be obtained through www.astm.org or by contacting ASTM at (610) 832-9585 (phone), (610) 832-9555 (fax), or through [email protected] (email). To inquire about consensus standard content and/or membership or about ASTM Offices abroad, contact Joe Koury, Staff Manager for Committee F44 on General Aviation: (610) 832-9804, [email protected].

The FAA maintains a list of accepted MOCs on the FAA website at https://www.faa.gov/aircraft/air_cert/design_approvals/small_airplanes/small_airplanes_regs/.

Issued in Kansas City, Missouri, on May 3, 2018. Pat Mullen, Manager, Small Airplanes Standards Branch, Aircraft Certification Service.