76 FR 50 Airworthiness Directives; Airbus Model A310 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
This document is proposed. It may have been replaced. Check the official source before relying on it.
[Docket No. FAA-2010-1274; Directorate Identifier 2010-NM-090-AD] RIN 2120-AA64
Airworthiness Directives; Airbus Model A310 Series Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Summary
DGAC [Direction Générale de l'Aviation Civile] France AD 1992-106-132(B) * * * was issued to require a set of inspection and modification tasks which addressed JAR/FAR [Joint Aviation Regulation/Federal Aviation Regulation] 25-571 requirements related to damage-tolerance and fatigue evaluation of structure. * * * * * * * *
The unsafe condition is reduced structural integrity of the wings. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.
Dates
DATES: We must receive comments on this proposed AD by February 17, 2011.
ADDRESSES: You may send comments by any of the following methods:
• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
• Fax: (202) 493-2251.
• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
Addresses
• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact Airbus SAS--EAW (Airworthiness Office), 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; e-mail [email protected]; Internet http://www.airbus.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221.
Examining the AD Docket
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.
For Further Information Contact
FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-2125; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include "Docket No. FAA-2010-1274; Directorate Identifier 2010-NM-090-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.
Comments Invited
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2009-0057, dated March 13, 2009 (referred to after this as "the MCAI"), to correct an unsafe condition for the specified products. The MCAI states:
Discussion
DGAC [Direction Générale de l'Aviation Civile] France AD 1992-106-132(B) original issue up to revision 7 was issued to require a set of inspection and modification tasks which addressed JAR/FAR [Joint Aviation Regulation/Federal Aviation Regulation] 25-571 requirements related to damage-tolerance and fatigue evaluation of structure.
Following the Extended Design Service Goal activities as part of the Structure Task Group for the Airbus A310 program, EASA published AD 2007-0053, which replaced DGAC France AD F-1992-106-132R7.
Since the issuance of AD 2007-0053R1, the thresholds and the intervals of Airbus Service Bulletins (SB) A310-57-2050 and A310-57-2064 have been updated.
Consequently, this new [EASA] AD takes over the requirements of paragraphs 1.15 and 1.17 of EASA AD 2007-0053R1, which has been revised accordingly * * * and requires the accomplishment of Airbus SB A310-57-2048 at revision 01.
The unsafe condition is reduced structural integrity of the wings. The required actions are as follows, depending on airplane configuration:
• Cold working of trellis boom drainage holes.
• Repetitive detailed or rotating probe inspections for cracking in the drain holes on the lower skin panel in the center wing box between frames 42 and 46 and corrective actions if necessary. Corrective actions include repairing cracking and contacting the FAA or EASA for repair and doing the repair.
• Repetitive eddy current inspections for cracking of the upper corner angle fitting and the vertical tee fitting at left and right frame 40, and corrective actions if necessary. Corrective actions include repairing, replacing the internal angle fitting and contacting the FAA or EASA for repair and doing the repair.
You may obtain further information by examining the MCAI in the AD docket.
Other Relevant Rulemaking
Other Relevant Rulemaking
We are considering issuing three other NPRMs related to this NPRM:
• Directorate Identifier 2010-NM-092-AD. That NPRM proposes to supersede AD 98-26-01, amendment 39-10942 (63 FR 69179, December 16, 1998), to continue to require certain actions specified in that AD. However, that NPRM does not restate paragraphs (p) and (r) of AD 98-26-01. Instead, certain requirements of paragraphs (p) and (r) of that AD are included in this NPRM, Directorate Identifier 2010-NM-090-AD.
• Directorate Identifiers 2010-NM-089-AD and 2010-NM-091-AD. Both of these NPRMs include the requirements of certain other paragraphs of AD 98-26-01.
Relevant Service Information
Relevant Service Information
Airbus has issued the service bulletins listed in the table that follows:
Table--Service Information
Service bulletin Revision Date
Airbus Mandatory Service Bulletin A310-57- 01 … May 22, 2007.
2048.
Airbus Mandatory Service Bulletin A310-57- 02 … August 27, 2009.
2050, including Appendix 01.
Airbus Mandatory Service Bulletin A310-57- 02 … December 21, 2007.
2064, including Appendix 1.
The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.
Differences Between This AD and the MCAI or Service Information
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a Note within the proposed AD.
Costs of Compliance
Costs of Compliance
Based on the service information, we estimate that this proposed AD would affect about 44 products of U.S. registry. We also estimate that it would take about 137 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $512,380, or $11,645 per product.
Authority for This Rulemaking
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. "Subtitle VII: Aviation Programs," describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in "Subtitle VII, Part A, Subpart III, Section 44701: General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
Regulatory Findings
We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
1. Is not a "significant regulatory action" under Executive Order 12866;
2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. The FAA amends § 39.13 by adding the following new AD:
Airbus: Docket No. FAA-2010-1274; Directorate Identifier 2010-NM-090-AD.
Comments Due Date
(a) We must receive comments by February 17, 2011.
Affected ADs
Affected ADs
(b) None.
Applicability
(c) This AD applies to Airbus Model A310-203, -204, -221, -222, -304, -322, -324, and -325 airplanes, certificated in any category, all serial numbers.
Subject
(d) Air Transport Association (ATA) of America Code 57: Wings.
Reason
(e) The mandatory continuing airworthiness information (MCAI) states:
Reason
DGAC [Direction Générale de l'Aviation Civile] France AD 1992-106-132(B) original issue up to revision 7 was issued to require a set of inspection and modification tasks which addressed JAR/FAR [Joint Aviation Regulation/Federal Aviation Regulation] 25-571 requirements related to damage-tolerance and fatigue evaluation of structure. * * *. * * * * * The unsafe condition is reduced structural integrity of the wings.
Compliance
Compliance
(f) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
Cold Working of Trellis Boom Drainage Holes
(g) For Model A310-203, -204, -222, -304, -322 and -324 airplanes, except airplanes identified in paragraphs (g)(1), (g)(2), and (g)(3) of this AD: Within the applicable time specified in Table 1 of this AD, cold work the trellis boom drainage holes, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310-57-2048, Revision 01, dated May 22, 2007. Certain compliance times specified in Table 1 of this AD are applicable to short range use, average flight time (AFT) equal to or less than 3.6 hours; or long range use, AFT exceeding 3.6 hours.
Cold Working of Trellis Boom Drainage Holes
Table 1--Compliance Times for Paragraph (g) of This AD
Airplanes, as identified in Compliance time (whichever occurs later)
Airbus mandatory service
bulletin A310-57-2048, revision 01, dated May 22,
2007
Configuration 01 airplanes.. Prior to the Within 6 months
accumulation of after the effective
Airplanes, as identified in Compliance time (whichever occurs later)
31,800 total flight date of this AD.
cycles or 63,600
total flight hours,
whichever occurs
first.
Configuration 02 airplanes.. Prior to the Within 6 months
accumulation of after the effective
40,000 total flight date of this AD.
cycles or 80,000
total flight hours,
whichever occurs
first.
Configuration 03 short range Prior to the Within 6 months
airplanes. accumulation of after the effective
30,950 total flight date of this AD.
cycles or 86,750
total flight hours,
whichever occurs
first.
Configuration 03 long range Prior to the Within 6 months
airplanes. accumulation of after the effective
24,100 total flight date of this AD.
cycles or 120,600
total flight hours,
whichever occurs
first.
(1) Airplanes on which Airbus modification 06130 was done in production.
(2) Airplanes on which Airbus Mandatory Service Bulletin A310-57-2048 was done in service.
(3) Airplanes on which rework of cracked drain holes was done in accordance with Airbus Mandatory Service Bulletin A310-57-2050.
Inspection of Trellis Boom Drainage Holes
Inspection of Trellis Boom Drainage Holes
(h) For all airplanes: Within the applicable intervals specified in Table 2 of this AD, perform a detailed or rotating probe inspection for cracking in the drain holes on the lower skin panel in the center wing box between frames 42 and 46, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310-57-2050, Revision 02, dated August 27, 2009. Repeat the inspections thereafter at intervals not to exceed the applicable times specified in Table 3 of this AD. Certain compliance times specified in Tables 2 and 3 of this AD are applicable to short range use, average flight time (AFT) equal to or less than 3.6 hours; or long range use, AFT exceeding 3.6 hours.
Table 2--Compliance Times for Paragraph (h) of This AD
Airplanes, as identified in Compliance time (whichever occurs later)
Airplanes, as identified in Compliance time (whichever occurs later)
Airbus mandatory service
bulletin A310-57-2050,
revision 02, dated August
27, 2009
Configuration 01 airplanes.. Prior to the Within 1,000 flight
accumulation of cycles or 2,000
17,800 total flight flight hours,
cycles or 35,600 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Airplanes, as identified in Compliance time (whichever occurs later)
Airbus mandatory service
bulletin A310-57-2050,
revision 02, dated August
27, 2009
Configuration 02 airplanes Within 32,850 flight Within 1,000 flight
on which Airbus Mandatory cycles or 65,700 cycles or 2,000
Service Bulletin A310-57- flight hours, flight hours,
2048 has been done within whichever occurs whichever occurs
the "recommended" first, after first, after the
compliance times specified accomplishing effective date of
in paragraph 1.E.(2), Airbus Mandatory this AD.
"Accomplishment Service Bulletin
Timescale," of Airbus A310-57-2048.
Mandatory Service Bulletin A310-57-2048, Revision 01, dated May 22, 2007.
Configuration 02 airplanes Within 8,600 flight Within 1,000 flight
on which Airbus Mandatory cycles or 17,250 cycles or 2,000
Service Bulletin A310-57- flight hours, flight hours,
2048 has not been done whichever occurs whichever occurs
within the "recommended" first, after first, after the
compliance times specified accomplishing the effective date of
in paragraph 1.E.(2), detailed inspection this AD.
"Accomplishment specified in Airbus
Timescale," of Airbus Mandatory Service
Mandatory Service Bulletin Bulletin A310-57-
A310-57-2048, Revision 01, 2048;
dated May 22, 2007. OR …
Within 11,400 flight
cycles or 22,800
flight hours,
whichever occurs
first, after
accomplishing the
rotating probe
inspection
specified in Airbus
Mandatory Service
Bulletin A310-57-
2048.
Configuration 03 airplanes.. Prior to the Within 1,000 flight
accumulation of cycles or 2,000
22,300 total flight flight hours,
cycles or 44,550 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 04 airplanes.. Prior to the Within 1,000 flight
accumulation of cycles or 2,000
41,550 total flight flight hours,
cycles or 83,100 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 05 airplanes Prior to the Within 1,000 flight
on which Airbus Mandatory accumulation of cycles or 2,000
Service Bulletin A310-57- 40,000 total flight flight hours,
2048 has been done within cycles or 80,000 whichever occurs
the "recommended" total flight hours, first, after the
compliance times specified whichever occurs effective date of
in paragraph 1.E.(2), first. this AD.
"Accomplishment Timescale," of Airbus Mandatory Service Bulletin A310-57-2048, Revision 01, dated May 22, 2007.
Configuration 05 airplanes Within 10,600 flight Within 1,000 flight
on which Airbus Mandatory cycles or 21,150 cycles or 2,000
Service Bulletin A310-57- flight hours, flight hours,
2048 has not been done whichever occurs whichever occurs
within the "recommended" first, after first, after the
compliance times specified accomplishing the effective date of
in paragraph 1.E.(2), detailed inspection this AD.
"Accomplishment specified in Airbus
Timescale," of Airbus Mandatory Service
Mandatory Service Bulletin Bulletin A310-57-
A310-57-2048, Revision 01, 2048;
dated May 22, 2007. OR …
Within 13,900 flight
cycles or 27,800
flight hours,
whichever occurs
first, after
accomplishing the
rotating probe
inspection
specified in Airbus
Mandatory Service
Bulletin A310-57-
2048.
Configuration 06 short range Prior to the Within 1,000 flight
airplanes. accumulation of cycles or 2,800
17,250 total flight flight hours,
cycles or 48,400 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 06 long range Prior to the Within 800 flight
airplanes. accumulation of cycles or 4,000
13,450 total flight flight hours,
cycles or 67,250 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 07 short range Prior to the Within 1,000 flight
airplanes. accumulation of cycles or 2,800
32,150 total flight flight hours,
cycles or 90,050 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 07 long range Prior to the Within 800 flight
airplanes. accumulation of cycles or 4,000
25,050 total flight flight hours,
cycles or 125,150 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Configuration 08 short range Prior to the Within 1,000 flight
airplanes on which Airbus accumulation of cycles or 2,800
Mandatory Service Bulletin 30,950 total flight flight hours,
A310-57-2048 has been done cycles or 86,750 whichever occurs
within the "recommended" total flight hours, first, after the
compliance times specified whichever occurs effective date of
in paragraph 1.E.(2), first. this AD.
"Accomplishment Timescale," of Airbus Mandatory Service Bulletin A310-57-2048, Revision 01, dated May 22, 2007.
Airplanes, as identified in Compliance time (whichever occurs later)
Airbus mandatory service
bulletin A310-57-2050,
revision 02, dated August
27, 2009
Configuration 08 short range Within 8,200 flight Within 1,000 flight
Configuration 08 short range Within 8,200 flight Within 1,000 flight
airplanes on which Airbus cycles or 23,000 cycles or 2,800
Mandatory Service Bulletin flight hours, flight hours,
A310-57-2048 has not been whichever occurs whichever occurs
done within the first, after first, after the
"recommended" compliance accomplishing the effective date of
times specified in detailed inspection this AD.
paragraph 1.E.(2), specified in Airbus
"Accomplishment Mandatory Service
Timescale," of Airbus Bulletin A310-57-
Mandatory Service Bulletin 2048;
A310-57-2048, Revision 01, OR …
dated May 22, 2007. Within 10,800 flight
cycles or 30,300
flight hours,
whichever occurs
first, after
accomplishing the
rotating probe
inspection
specified in Airbus
Mandatory Service
Bulletin A310-57-
2048.
Configuration 08 long range Prior to the Within 800 flight
airplanes on which Airbus accumulation of cycles or 4,000
Mandatory Service Bulletin 24,100 total flight flight hours,
A310-57-2048 has been done cycles or 120,600 whichever occurs
within the "recommended" total flight hours, first, after the
compliance times specified whichever occurs effective date of
in paragraph 1.E.(2), first. this AD.
"Accomplishment Timescale," of Airbus Mandatory Service Bulletin A310-57-2048, Revision 01, dated May 22, 2007. Configuration 08 long range Within 6,400 flight Within 800 flight
airplanes on which Airbus cycles or 31,950 cycles or 4,000
Mandatory Service Bulletin flight hours, flight hours,
A310-57-2048 has not been whichever occurs whichever occurs
done within the first, after first, after the
"recommended" compliance accomplishing the effective date of
times specified in detailed inspection this AD.
paragraph 1.E.(2), specified in Airbus
"Accomplishment Mandatory Service
Timescale," of Airbus Bulletin A310-57-
Mandatory Service Bulletin 2048;
A310-57-2048, Revision 01, OR …
dated May 22, 2007. Within 8,400 flight
cycles or 42,150
flight hours,
whichever occurs
first, after
accomplishing the
rotating probe
inspection
specified in Airbus
Mandatory Service
Bulletin A310-57-
2048.
Table 3--Repetitive Intervals for Paragraph (h) of This AD, Depending on Most Recent Inspection Type
Airplanes, as identified in Airbus Type of inspection done
mandatory service bulletin A310-57-2050, during most recent Repetitive interval (not to exceed)
revision 02, dated August 27, 2009 inspection
Configuration 01 and 02 airplanes … Detailed inspection … 8,600 flight cycles or 17,250 flight
hours, whichever occurs first.
Rotating probe inspection.. 11,400 flight cycles or 22,800 flight
hours, whichever occurs first.
Configurations 03, 04, and 05 airplanes. Detailed inspection … 10,600 flight cycles or 21,150 flight
hours, whichever occurs first.
Rotating probe inspection.. 13,900 flight cycles or 27,800 flight
hours, whichever occurs first.
Configurations 06, 07, and 08 short Detailed inspection … 8,200 flight cycles or 23,000 flight
range airplanes. hours, whichever occurs first.
Rotating probe inspection.. 10,800 flight cycles or 30,300 flight
hours, whichever occurs first.
Configurations 06, 07, and 08 long range Detailed inspection … 6,400 flight cycles or 31,950 flight
airplanes. hours, whichever occurs first.
Rotating probe inspection.. 8,400 flight cycles or 42,150 flight
hours, whichever occurs first.
Corrective Actions for Paragraph (h) of This AD
Corrective Actions for Paragraph (h) of This AD
(i) If any cracking is found during any inspection required by paragraph (h) of this AD, before further flight, do all applicable corrective actions, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310-57-2050, Revision 02, dated August 27, 2009; except where the service bulletin specifies to contact Airbus, before further flight, repair in accordance with a method approved by either the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, or EASA (or its delegated agent).
Inspection of Fuselage Frame 40 Upper Corner Fitting
Inspection of Fuselage Frame 40 Upper Corner Fitting
(j) For all airplanes: Within the applicable time specified in Table 4 of this AD, perform an eddy current inspection for cracking of the upper corner fitting at left and right frame 40, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310-57-2064, Revision 02, dated December 21, 2007. Repeat the inspections thereafter at intervals not to exceed the applicable times specified in Table 5 of this AD. Certain compliance times specified in Tables 4 and 5 of this AD are applicable to short range use, average flight time (AFT) equal to or less than 3.23 hours; or long range use, AFT exceeding 3.23 hours.
Table 4--Compliance Times for Paragraph (j) of This AD
Airplane configurations Compliance time (whichever occurs later)
identified in Airbus mandatory service bulletin A310-57-2064, revision 02, dated December 21, 2007
identified in Airbus mandatory service bulletin A310-57-2064, revision 02, dated December 21, 2007
Model A310-203, -204, -221, Prior to the Within 1,300 flight
and -222 airplanes accumulation of cycles or 2,700
identified as Configuration 15,100 total flight flight hours,
01. cycles or 30,300 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Model A310-203, -204, -221, Prior to the Within 1,300 flight
and -222 airplanes accumulation of cycles or 2,700
identified as 21,400 total flight flight hours,
Configurations 02 and 03. cycles or 42,800 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Model A310-304, -322, -324, Prior to the Within 600 flight
and -325 short range accumulation of cycles or 1,800
airplanes identified as 14,700 total flight flight hours,
Configuration 01. cycles or 41,300 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Model A310-304, -322, -324, Prior to the Within 600 flight
and -325 short range accumulation of cycles or 1,800
airplanes identified as 20,700 total flight flight hours,
Configurations 02 and 03. cycles or 58,300 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Model A310-304, -322, -324, Prior to the Within 500 flight
and -325 long range accumulation of cycles or 2,650
airplanes identified as 12,800 total flight flight hours,
Configuration 01. cycles or 64,000 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Model A310-304, -322, -324, Prior to the Within 500 flight
and -325 long range accumulation of cycles or 2,650
airplanes identified as 18,000 total flight flight hours,
Configurations 02 and 03. cycles or 90,400 whichever occurs
total flight hours, first, after the
whichever occurs effective date of
first. this AD.
Table 5--Repetitive Intervals for Paragraph (j) of This AD
Repetitive interval (not to
Airplanes exceed)
Model A310-203, -204, -221, and - 8,750 flight cycles or 17,550
222 airplanes. flight hours, whichever occurs
first.
Model A310-304, -322, -324, and - 5,800 flight cycles or 16,300
325 short range airplanes. flight hours, whichever occurs
first.
Model A310-304, -322, -324, and - 4,800 flight cycles or 24,050
325 long range airplanes. flight hours, whichever occurs
first.
Corrective Actions for Paragraph (h) of This AD
Corrective Actions for Paragraph (h) of This AD
(k) If, during any inspection required by paragraph (j) of this AD, any crack is found, prior to further flight, do all applicable corrective actions, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A310-57-2064, Revision 02, dated December 21, 2007; except where the service bulletin specifies to contact Airbus, before further flight, repair in accordance with a method approved by either the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, or EASA (or its delegated agent).
Credit for Actions Accomplished in Accordance With Previous Service Information
Credit for Actions Accomplished in Accordance With Previous Service Information
(l) Actions accomplished before the effective date of this AD in accordance with Airbus Service Bulletin A310-57-2048, dated April 23, 1990, are considered acceptable for compliance with the corresponding action specified in paragraph (g) of this AD.
(m) Actions accomplished before the effective date of this AD in accordance with Airbus Service Bulletin A310-57-2050, dated April 23, 1990; or Airbus Mandatory Service Bulletin A310-57-2050, Revision 01, dated May 22, 2007; are considered acceptable for compliance with the corresponding actions specified in paragraphs (h) and (i) of this AD.
(n) Actions done before the effective date of this AD in accordance with Airbus Service Bulletin A310-57-2064, dated August 24, 1995; or Revision 01, dated January 5, 2001; are acceptable for compliance with the corresponding actions specified in paragraphs (j) and (k) of this AD.
FAA AD Differences
FAA AD Differences
Note 1: This AD differs from the MCAI and/or service information as follows: No Differences.
Other FAA AD Provisions
(o) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Dan Rodina, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-2125; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD.
Other FAA AD Provisions
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.
Related Information
Related Information
(p) Refer to MCAI EASA Airworthiness Directive 2009-0057, dated March 13, 2009, and the service bulletins listed in Table 6 of this AD, for related information.
Table 6--Service Information
Service bulletin Revision Date
Airbus Mandatory Service Bulletin A310-57- 01 … May 22, 2007.
2048.
Airbus Mandatory Service Bulletin A31-57- 02 … August 27, 2009.
2050.
Airbus Mandatory Service Bulletin A310-57- 02 … December 21, 2007.
2064.
Issued in Renton, Washington on December 17, 2010. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service.