70 FR 24326 Airworthiness Directives; BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. This proposed AD would require repetitive detailed and specialized inspections to detect fatigue damage in the fuselage, replacement of certain bolt assemblies, and corrective actions if necessary. This proposed AD is prompted by a review of primary airframe fatigue test results and Maintenance Steering Group 3 (MSG-3) analysis. We are proposing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
This document is proposed. It may have been replaced. Check the official source before relying on it.
Rules DEPARTMENT OF TRANSPORTATION
[Docket No. FAA-2005-21137; Directorate Identifier 2002-NM-86-AD] RIN 2120-AA64
Airworthiness Directives; BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).
Action
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. This proposed AD would require repetitive detailed and specialized inspections to detect fatigue damage in the fuselage, replacement of certain bolt assemblies, and corrective actions if necessary. This proposed AD is prompted by a review of primary airframe fatigue test results and Maintenance Steering Group 3 (MSG-3) analysis. We are proposing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
Dates
DATES: We must receive comments on this proposed AD by June 8, 2005.
ADDRESSES: Use one of the following addresses to submit comments on this proposed AD.
• DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.
• Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.
Addresses
• Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, room PL-401, Washington, DC 20590.
• By fax: (202) 493-2251.
• Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact British Aerospace Regional Aircraft American Support, 13850 Mclearen Road, Herndon, Virginia 20171.
You can examine the contents of this AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, on the plaza level of the Nassif Building, Washington, DC. The docket number is FAA-2005-21137; the directorate identifier for this docket is 2002-NM-86-AD.
For Further Information Contact
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-1175; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Comments Invited
We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed under ADDRESSES. Include "Docket No. FAA-2005-21137; Directorate Identifier 2002-NM-86-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments submitted by the closing date and may amend the proposed AD in light of those comments.
We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of our docket website, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You can review the DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78), or you can visit http://dms.dot.gov.
Examining the Docket
Examining the Docket
You can examine the AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the DMS receives them.
Discussion
Discussion
The Civil Aviation Authority (CAA), which is the airworthiness authority for the United Kingdom, notified us that an unsafe condition may exist on all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. The CAA advises that, following an extensive review of the primary airframe fatigue test results and Maintenance Steering Group 3 (MSG-3) analysis for the Model 4101 airplanes, new areas and thresholds of fatigue damage were identified. New inspections and revisions to existing inspections for fatigue damage (requirements and inspection thresholds in particular) are needed to address the findings. These inspections are necessary to maintain the structural integrity of the airplane. Fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, if not detected and corrected in a timely manner, could result in reduced structural integrity of the airplane.
Relevant Service Information
Relevant Service Information
BAE Systems (Operations) Limited has issued Service Bulletin J41-51-001, Revision 2, dated April 30, 2003. The service bulletin describes procedures for repetitive detailed and specialized inspections of the fuselage to detect fatigue damage, replacement of the bolt assemblies of the pintle bearing housing and upper club foot fitting with new bolt assemblies, and corrective actions if necessary. The specialized inspections include eddy current inspections (including high frequency and rotating), radiographic inspections, a magnetic particle inspection, and a torque measurement. The areas to be inspected are located in or around door, fuselage, engine nacelle, empennage, and wing structures. In addition, the service bulletins specify submitting inspection reports after most of the inspection procedures are completed. The corrective actions include replacing a damaged part with a new part, and repairing damage in accordance with the service bulletin, or in accordance with a method approved by BAE Systems (Operations) Limited if damage is outside specified limits. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The CAA mandated the service information and issued British airworthiness directive 005-02-2002 to ensure the continued airworthiness of these airplanes in the United Kingdom.
FAA's Determination and Requirements of the Proposed AD
FAA's Determination and Requirements of the Proposed AD
This airplane model is manufactured in the United Kingdom and is type certificated for operation in the United States under the provisions of § 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the CAA has kept the FAA informed of the situation described above. We have examined the CAA's findings, evaluated all pertinent information, and determined that we need to issue an AD for products of this type design that are certificated for operation in the United States.
Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously, except as discussed under "Differences Between the Proposed AD and the Service Bulletin."
Differences Between the Proposed AD and the Service Bulletin
Differences Between the Proposed AD and the Service Bulletin
Operators should note that, although the Accomplishment Instructions of the referenced service bulletin describes procedures for submitting inspection reports, this proposed AD would not require those actions. We do not need this information from operators.
The service bulletin specifies that you may contact the manufacturer for instructions on how to repair certain conditions, but this proposed AD would require you to repair those conditions using a method that we or the CAA (or its delegated agent) approve. In light of the type of repair that would be required to address the unsafe condition, and consistent with existing bilateral airworthiness agreements, we have determined that, for this proposed AD, a repair we or the CAA approve would be acceptable for compliance with this proposed AD.
Grace Period
Grace Period
Operators should note that, although the service bulletin does not list a grace period in the compliance times for some of the actions, this proposed AD adds a grace period to the compliance times. We find that a grace period will keep airplanes from being grounded unnecessarily.
Also, although the service bulletin specifies a grace period for some actions, this proposed AD has a different grace period. We find that this modified grace period will keep airplanes from being grounded unnecessarily.
Clarification of Flight Cycle Terminology
Clarification of Flight Cycle Terminology
Operators should note that, although the Accomplishment Instructions of the referenced service bulletins use "flights" to define some compliance times, this proposed AD uses "total flight cycles."
Clarification of Inspection Terminology
In this proposed AD, the "detailed visual inspection," "detailed internal visual inspection," "detailed internal inspection," and "detailed external visual inspection" specified in the service bulletin are referred to as a "detailed inspection." We have included the definition for a detailed inspection in Note 1 of the proposed AD.
Clarification of Initial Inspection Threshold
Clarification of Initial Inspection Threshold
For airplanes not inspected previously, the service bulletin specifies inspection thresholds of 8 years and 4 years after first flight. However, for these same airplanes, paragraph (g) of this proposed AD specifies an inspection threshold of 96 months (8 years) and 48 months (4 years), as applicable, after the date of issuance of the original standard Airworthiness Certificate or the date of issuance of the original Export Certificate of Airworthiness. This decision is based on our determination that "first flight" may be interpreted differently by different operators. We find that our proposed terminology is generally understood within the industry and records will always exist that establish these dates with certainty.
Costs of Compliance
Costs of Compliance
The following table provides the estimated costs for U.S. operators to comply with this proposed AD.
Estimated Costs
Cost per
Work Average labor airplane, per Number of U.S.-
Action hours rate per hour Parts inspection registered Fleet cost
cycle airplanes
Inspections of the door structure … 17 $65 None … $1,105 57 Up to $62,985, per
inspection cycle.
Inspections of the fuselage structure.. 164 65 None … 10,660 57 Up to $607,620, per
inspection/replacement
cycle.
Inspections of the engine nacelle 4 65 None … 260 57 Up to $14,820, per
structure. inspection cycle.
Inspections of the empennage structure. 14 65 None … 910 57 Up to $51,870, per
inspection cycle.
Inspections of the wing structure … 24 65 None … 1,560 57 Up to $88,920, per
inspection cycle.
The total proposed actions would take about 223 work hours per airplane, at an average labor rate of $65 per work hour. Based on these figures, the estimated cost of the total proposed AD for U.S. operators is up to $826,215, or $14,495 per airplane, per inspection cycle.
Authority for This Rulemaking
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
Regulatory Findings
We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed regulation:
1. Is not a "significant regulatory action" under Executive Order 12866;
2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD. See the ADDRESSES section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
PART 39--AIRWORTHINESS DIRECTIVES
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):
BAE Systems (Operations) Limited (Formerly British Aerospace Regional Aircraft): Docket No. FAA-2005-21137; Directorate Identifier 2002-NM-86-AD.
Comments Due Date
Comments Due Date
(a) The Federal Aviation Administration must receive comments on this AD action by June 8, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all BAE Systems (Operations) Limited Model Jetstream 4101 airplanes, certificated in any category.
Unsafe Condition
Unsafe Condition
(d) This AD was prompted by a review of primary airframe fatigue test results and Maintenance Steering Group 3 (MSG-3) analysis. We are issuing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
Compliance
Compliance
(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
Service Bulletin Reference
(f) The term "the service bulletin," as used in this AD, means BAE Systems (Operations) Limited Service Bulletin J41-51-001, Revision 2, dated April 30, 2003.
Inspection and Corrective Actions
Inspection and Corrective Actions
(g) At the compliance times specified in the "Initial Compliance Time" column of Tables 1, 2, 3, 4, and 5 of this AD: Do the applicable detailed inspections and specialized inspections to detect fatigue damage, and replacement of certain bolt assemblies, and any applicable corrective actions, in accordance with the Accomplishment Instructions of the service bulletin. Do any corrective action before further flight. Repeat the inspections and replacement thereafter at intervals specified in the "Repetitive Intervals" column of Tables 1, 2, 3, 4, and 5 of this AD.
Note 1: For the purposes of this AD, a detailed inspection is: "An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required."
Table 1.--Appendix 1 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 1 of the "grace period") Repetitive intervals
service bulletin -----------------------------------------------------
Inspection threshold Grace period
1, 6 … Before the accumulation Within 500 flight cycles At intervals not to
of 22,500 total flight after the effective exceed 3,300 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
2 … Before the accumulation Within 500 flight cycles At intervals not to
of 20,000 total flight after the effective exceed 5,200 flight
cycles. date of this AD. cycles.
3, 5, 7 … Before the accumulation Within 500 flight cycles At intervals not to
of 21,000 total flight after the effective exceed 10,000 flight
cycles. date of this AD. cycles.
4 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 26,000 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
Table 2.--Appendix 2 Compliance Times
Initial compliance time (whichever occurs later
between the times in "inspection/replacement
Part of actions threshold" and "grace period")
specified in appendix 2 of the ----------------------------------------------------- Repetitive intervals
service bulletin Inspection/replacement
threshold Grace period
1, 3, 32 … Within 96 months after 12 months after the At intervals not to
the date of issuance of effective date of this exceed 24 months.
the original standard AD.
Airworthiness
Certificate or the date
of issuance of the
original Export
Certificate of
Airworthiness, whichever
occurs later.
2 … Before the accumulation Within 500 flight cycles At intervals not to
of 23,000 total flight after the effective exceed 10,000 flight
cycles. date of this AD. cycles.
4, 10, 11, 12, 13 … Before the accumulation Within 500 flight cycles At intervals not to
of 20,000 total flight after the effective exceed 6,600 flight
cycles. date of this AD. cycles.
5 … Within 48 months after 12 months after the At intervals not to
the date of issuance of effective date of this exceed 24 months.
the original standard AD.
Airworthiness
Certificate or the date
of issuance of the
original Export
Certificate of
Airworthiness, whichever
occurs later.
6 … Before the accumulation Within 500 flight cycles At intervals not to
of 20,000 total flight after the effective exceed 5,400 flight
cycles. date of this AD. cycles.
7 … Before the accumulation Within 500 flight cycles At intervals not to
of 22,400 total flight after the effective exceed 8,200 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
8 … Before the accumulation Within 500 flight cycles At intervals not to
of 19,000 total flight after the effective exceed 8,200 flight
cycles. date of this AD. cycles.
9 … Before the accumulation Within 500 flight cycles At intervals not to
of 23,000 total flight after the effective exceed 23,000 flight
cycles. date of this AD. cycles.
14 … Before the accumulation Within 500 flight cycles At intervals not to
of 19,700 total flight after the effective exceed 4,700 flight
cycles. date of this AD. cycles.
15 … Before the accumulation Within 500 flight cycles At intervals not to
of 25,000 total flight after the effective exceed 13,600 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
16, 19, 20 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 25,800 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
17, 21, 29, 30 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 30,000 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
18 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 33,000 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
22 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 16,500 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
23 … Before the accumulation Within 500 flight cycles At intervals not to
of 22,000 total flight after the effective exceed 7,400 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
24 … Before the accumulation Within 500 flight cycles At intervals not to
of 23,600 total flight after the effective exceed 15,700 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
25 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 12,700 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
26 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed the 21,800
cycles and after the date of this AD. flight cycles.
accumulation of 20,000
total flight cycles.
27 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 18,300 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
28 … Between 20,000 and 26,000 Within 500 flight cycles At intervals not to
total flight cycles. after the effective exceed 9,500 flight
date of this AD. cycles.
31 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 16,300 flight
cycles and after the date of this AD. cycles.
accumulation of 20,000
total flight cycles.
33 … Before the accumulation Within 500 flight cycles At intervals not to
of 26,000 total flight after the effective exceed 26,000 flight
cycles. date of this AD. cycles.
Table 3.--Appendix 3 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 3 of the "grace period") Repetitive intervals
service bulletin --------------------------------------------------------
Inspection threshold Grace period
1, 2 … Before the accumulation of Within 500 flight cycles At intervals not to
24,000 total flight after the effective date exceed 11,000
cycles and after the of this AD. flight cycles.
accumulation of 20,000
total flight cycles.
Table 4.--Appendix 4 Compliance Times
Initial Compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 4 of the "grace period") Repetitive intervals
service bulletin --------------------------------------------------------
Inspection threshold Grace period
1 … Before the accumulation of Within 500 flight cycles At intervals not to
26,000 total flight after the effective date exceed 12,000
cycles and after the of this AD. flight cycles.
accumulation of 20,000
total flight cycles.
2 … Before the accumulation of Within 500 flight cycles At intervals not to
26,000 total flight after the effective date exceed 30,000
cycles and after the of this AD. flight cycles.
accumulation of 20,000
total flight cycles.
3, 5 … Within 48 months after the 12 months after the At intervals not to
date of issuance of the effective date of this AD. exceed 48 months.
original standard
Airworthiness Certificate
or the date of issuance
of the original Export
Certificate of
Airworthiness, whichever
occurs later.
4, 6 … 96 months after the date 12 months after the At intervals not to
of issuance of the effective date of this AD. exceed 48 months.
original standard
Airworthiness Certificate
or the date of issuance
of the original Export
certificate of
Airworthiness, whichever
occurs later.
Table 5.--Appendix 5 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 5 of the "grace period") Repetitive intervals
service bulletin --------------------------------------------------------
Inspection threshold Grace period
1, 7 … Before the accumulation of Within 500 flight cycles At intervals not to
26,000 total flight after the effective date exceed 30,000
cycles and after the of this AD. flight cycles.
accumulation of 20,000
total flight cycles.
2, 5, 6 … Before the accumulation of Within 500 flight cycles At intervals not to
26,000 total flight after the effective date exceed 9,000 flight
cycles and after the of this AD. cycles.
accumulation of 20,000
total flight cycles.
3, 4 … Before the accumulation of Within 500 flight cycles At intervals not to
26,000 total flight after the effective date exceed 7,900 flight
cycles and after the of this AD. cycles.
accumulation 20,000 total
flight cycles.
Repairs for Damage Beyond Service Bulletin Limits
(h) If any fatigue damage is found that exceeds the limits specified in the service bulletin: Before further flight, repair the damage according to a method approved by either the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate; or the Civil Aviation Authority (or its delegated agent).
Previous Actions
Previous Actions
(i) Actions done before the effective date of this AD in accordance with BAE Systems (Operations) Limited Service Bulletin J41-51-001, dated February 15, 2002; and Revision 1, dated August 7, 2002, are acceptable for compliance with the requirements of paragraphs (g) and (h) of this AD.
No Report Required
No Report Required
(j) Although the service bulletin referenced in this AD specifies to submit certain information to the manufacturer, this AD does not include that requirement.
Alternative Methods of Compliance (AMOCs)
(k) The Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.
Related Information
Related Information
(l) British airworthiness directive 005-02-2002 also addresses the subject of this AD.
Issued in Renton, Washington, on April 29, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service.