Radar Vectors
Proposed Rule Proposed Issued Nov 21, 2005 5 pages Copy saved Nov 17, 2026

70 FR 70048 Airworthiness Directives; Airbus Model A310-200 and -300 Series Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Model A310-200 and -300 series airplanes. This proposed AD would require repetitive inspections for cracks and corrosion of the areas behind the scuff plates below the passenger/crew doors and bulk cargo door, and repair of any cracked or corroded part. This proposed AD also would require repetitive inspections for cracks of the holes of the corner doublers, the fail-safe ring, and the door frames of the passenger/crew door structures. This proposed AD is prompted by reports of corrosion behind the scuff plates at passenger/ crew doors and the bulk cargo door and fatigue cracks on the corner doublers of the forward and aft passenger/crew door frames. We are proposing this AD to prevent such corrosion and fatigue cracking, which could result in reduced structural integrity of the door surroundings.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2005-23007; Directorate Identifier 2005-NM-013-AD] RIN 2120-AA64

Airworthiness Directives; Airbus Model A310-200 and -300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

Summary

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Model A310-200 and -300 series airplanes. This proposed AD would require repetitive inspections for cracks and corrosion of the areas behind the scuff plates below the passenger/crew doors and bulk cargo door, and repair of any cracked or corroded part. This proposed AD also would require repetitive inspections for cracks of the holes of the corner doublers, the fail-safe ring, and the door frames of the passenger/crew door structures. This proposed AD is prompted by reports of corrosion behind the scuff plates at passenger/ crew doors and the bulk cargo door and fatigue cracks on the corner doublers of the forward and aft passenger/crew door frames. We are proposing this AD to prevent such corrosion and fatigue cracking, which could result in reduced structural integrity of the door surroundings.

Dates

DATES: We must receive comments on this proposed AD by December 21, 2005.

ADDRESSES: Use one of the following addresses to submit comments on this proposed AD.

• DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.

• Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.

Addresses

• Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, room PL-401, Washington, DC 20590.

• By fax: (202) 493-2251.

• Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France.

You can examine the contents of this AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, on the plaza level of the Nassif Building, Washington, DC. This docket number is FAA-2005-23007; the directorate identifier for this docket is 2005-NM-013-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Rosanne Ryburn, Aerospace Engineer, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2139; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

Comments Invited

We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed under ADDRESSES. Include "Docket No. FAA-2005-23007; Directorate Identifier 2005-NM-013-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments submitted by the closing date and may amend the proposed AD in light of those comments.

We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of our docket Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You can review the DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78), or you can visit http://dms.dot.gov.

Examining the Docket

Examining the Docket

You can examine the AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility Office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility Office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the DMS receives them.

Discussion

Discussion

The Direction Générale de l'Aviation Civile (DGAC), which is the airworthiness authority for France, notified us that an unsafe condition may exist on certain Airbus Model A310-200 and -300 series airplanes. The DGAC advises that it received reports indicating that corrosion was found behind the scuff plates at passenger/crew doors and the bulk cargo door. The DGAC also advises that results of structural fatigue testing have revealed that cracks were found on the corner doublers of the forward and aft passenger/crew door frames; and, after various simulated flights, on the fail-safe ring and frames 14 and 16A of the forward passenger/crew door. After 50,000 simulated flights, cracks measuring between 8.0 millimeters (mm) and 109.0 mm were found on the forward door frames and fail-safe ring. After 60,493 simulated flights, a 53.0 mm crack was found on the mid door frame. After 106,000 simulated flights, a 32.0 mm crack was found on the aft door frame. In all cases, the cracks originated at the fastener holes. In addition, cracks originating from corner doubler edges were found at the aft passenger/crew doors.

Such corrosion and fatigue cracking, if not detected and corrected, could result in reduced structural integrity of the door surroundings.

Other Relevant Rulemaking

We have previously issued AD 97-11-03, amendment 39-10032 (62 FR 28325, May 23, 1997), applicable to all Airbus Model A300 series airplanes. That AD requires inspections of the lower door surrounding structure to detect cracks and corrosion; inspections to detect cracking of the holes of the corner doublers, the fail-safe ring, and the door frames of the door structures; and repair if necessary. That AD also requires modification of the passenger/crew door frames, which terminates certain inspections.

Other Relevant Rulemaking

We also previously issued AD 98-16-05, amendment 39-10680 (63 FR 40812, July 31, 1998), applicable to all Airbus Model A300-600 series airplanes. That AD requires inspections of the areas behind the scuff plates below the passenger/crew doors and bulk cargo door to detect cracks and corrosion; inspections to detect cracking of the holes of the corner doublers, the fail-safe ring, and the door frames of the door structures; and repair if necessary. In addition, that AD provides for an optional terminating action for certain inspections. We are considering further rulemaking to mandate the optional terminating action.

Relevant Service Information

Relevant Service Information

Airbus has issued the service bulletins in the following table:

Service Bulletins

Airbus Service Bulletin-- Describes procedures for--

A310-53-2030, Revision 06, dated July Doing initial inspections for

2, 1996. cracks and corrosion of the

areas behind the scuff plates

below the passenger/crew doors

and bulk cargo door, and

repairing any cracked or

corroded part.

A310-53-2041, Revision 02, dated July Doing repetitive inspections

2, 1996. for cracks and corrosion of

the areas behind the scuff

plates below the passenger/

crew doors and bulk cargo

door, and repairing any

cracked or corroded part.

A310-53-2037, Revision 02, dated Doing repetitive inspections

November 27, 2000. for cracks of the holes of the

corner doublers, the fail-safe

ring, and the door frames of

the passenger/crew door

structures, and repairing any

cracked part.

A310-53-2017, Revision 09, dated May Modifying the passenger/crew

17, 2004. door structures, which ends

the repetitive inspections of

the holes of the corner

doublers, fail-safe ring, and

the door frames for certain

airplanes. The modification

includes cold expansion of

fastener holes; a ROTO test;

installation of new oversize

fasteners and modified

brackets; and installation of

an additional steel doubler.

Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The DGAC mandated the service information and issued French airworthiness directives 1991-132-124(B) R1, issued November 29, 2000, and F-2004-103, issued July 7, 2004, to ensure the continued airworthiness of these airplanes in France.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DGAC has kept the FAA informed of the situation described above. We have examined the DGAC's findings, evaluated all pertinent information, and determined that we need to issue an AD for products of this type design that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require accomplishing the applicable actions specified in the service information described previously, except as discussed under "Differences Between the Proposed AD, French Airworthiness Directive, and Service Bulletins."

Differences Between the Proposed AD, French Airworthiness Directive, and Service Bulletins

Differences Between the Proposed AD, French Airworthiness Directive, and Service Bulletins

Airbus Service Bulletin A310-53-2030 also does not list a grace period for certain compliance times. This proposed AD adds a grace period to certain compliance times. We find that a grace period will keep airplanes from being grounded unnecessarily.

Airbus Service Bulletins A310-53-2041 and A310-53-2037 specify repetitive inspections at "every" specified interval; however, this proposed AD would require compliance "at intervals not to exceed" the time specified in the service bulletin. These service bulletins also specify compliance times in "flights." This proposed AD would specify those times as flight cycles. In addition, Airbus Service Bulletin A310-53-2037 does not specify a starting date for the threshold for the initial inspections. This proposed AD would require compliance before the specified compliance time after the effective date of this AD.

Costs of Compliance

Costs of Compliance

The following table provides the estimated costs for U.S. operators to comply with this proposed AD. The average labor rate per hour is $65.

Estimated Costs

Number of U.S.-

Action Work hours Parts Cost per registered Fleet cost

airplane airplanes

Initial inspections behind 26 … None … $1,690 … 46 $77,740.

scuff plates (for all airplanes).

Repetitive inspections 26 … None … $1,690 … 46 $77,740, per

behind scuff plates, per inspection

inspection cycle (for all cycle.

airplanes).

Inspections of corner Between 4 and None … Between $260 46 Between

doublers, fail-safe ring, 50 depending and $3,250. $11,960, and

and door frames, per on kit $149,500 per

inspection cycle. purchased. inspection

cycle.

Terminating modification for Between 8 and Between $506 Between $1,026 46 Between $47,196

repetitive inspection of 55 depending and $6,098 and $9,673. and $444,958.

corner doublers, fail-safe on kit depending on

ring, and door frames. purchased. kit purchased.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 0130132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD. See the ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

PART 39--AIRWORTHINESS DIRECTIVES

Authority: 49 U.S.C. 106(g), 401013, 44701.

§ 39.13 [Amended]

2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD):

Airbus: Docket No. FAA-2005-23007; Directorate Identifier 2005-NM-013-AD.

Comments Due Date

(a) The FAA must receive comments on this AD action by December 21, 2005.

Affected ADs

Affected ADs

(b) None.

Applicability

(c) This AD applies to Airbus Model A310-203, -204, -221, and - 222 airplanes; and Airbus Model A310-304, -322, -324, and -325 airplanes; certificated in any category; excluding those airplanes on which Airbus Modification 5068, 7201, and 7298 have been incorporated in production.

Unsafe Condition

Unsafe Condition

(d) This AD was prompted by reports of corrosion behind the scuff plates at passenger/crew doors and the bulk cargo door and fatigue cracks on the corner doublers of the forward and aft passenger/crew door frames. We are issuing this AD to prevent such corrosion and fatigue cracking, which could result in reduced structural integrity of the door surroundings.

Compliance

Compliance

(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

Initial Inspections Behind Scuff Plates

(f) Do initial inspections (i.e., non-destructive tests) for cracks and corrosion of the areas behind the scuff plates below the passenger/crew doors and bulk cargo door, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-53-2030, Revision 06, dated July 2, 1996. Do the inspections at the applicable time specified in paragraphs (f)(1) and (f)(2) of Table 1 of this AD. If a records check cannot positively identify if the applicable modification or service information specified in paragraphs (f)(1) and (f)(2) of this AD has been done, assume that it has not.

Initial Inspections Behind Scuff Plates

Table 1.--Compliance Time Requirements for Initial Inspections Behind

Scuff Plates

For airplanes on which Modification 5382S6526 for

the forward doors and And-- Inspect--

Modification 5382D4741 for

all other doors--

(1) Have been incorporated None … Within 108 months

in production. after first flight.

(2) Have not been (i) Airbus Service Within 48 months

incorporated in production. Information Letter since the date of

(SIL) A300-53-033, issuance of the

Revision 2, dated original standard

November 23, 1984, Airworthiness

for all doors, was Certificate or the

not followed; or date of issuance of

Airbus Service the original Export

Bulletin A310-53- Certificate of

2004, Revision 2, Airworthiness, or

Modification 5382D4741 for

March 9, 1984 (only within 12 months

applicable for the after the effective

forward doors), was date of this AD,

not done. whichever occurs

later.

(ii) Airbus SIL A300- Within 60 months

53-033, Revision 2, since the date of

dated November 23, issuance of the

1984, for all original

doors, was Airworthiness

followed; or Airbus Certificate or the

Service Bulletin date of issuance of

A310-53-2004, the original Export

Revision 2, dated Certificate of

March 9, 1984 (only Airworthiness, or

applicable for the within 12 months

forward doors), was after the effective

done. date of this AD,

whichever occurs

later.

(iii) Airbus SIL Within 12 months

A300-53-033, after the effective

Revision 2, dated date of this AD.

November 23, 1984,

for all doors, was

followed; or Airbus

Service Bulletin

A310-53-2004,

Revision 2, dated

March 9, 1984 (only

applicable for the

forward doors), was

done more than 48

months ago as of

the effective date

of this AD.

Repetitive Inspections Behind Scuff Plates

Repetitive Inspections Behind Scuff Plates

(g) Following the initial inspection required by paragraph (f) of this AD, do repetitive inspections (i.e., non-destructive tests) for cracks and corrosion of the areas behind the scuff plates below the passenger/crew doors and bulk cargo door, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-53-2041, Revision 02, dated July 2, 1996. Repeat the inspections at the applicable times specified in paragraphs (g)(1) through (g)(4) of Table 2 of this AD.

Table 2.--Compliance Time Requirements for Repetitive Inspections Behind Scuff Plates

Unless in case of

corrosion removal,

For-- At-- Inspect at intervals then inspect at

not to exceed-- intervals not to

exceed--

(1) All airplanes … The forward passenger/crew 60 months … None.

doors and the bulk cargo

door.

(2) All airplanes … The aft passenger/crew 60 months … None.

doors, except the upper

and lower edges of the

door frame panel cutout.

(3) Model A310-203, -204, -221, and The aft passenger/crew 60 months or 12,000 60 months or 9,600

-222 airplanes. doors, the upper and lower flight cycles, flight cycles,

edges of the door frame whichever occurs whichever occurs

panel cutout. first. first.

(4) Model A310-304, -322, -324, and The aft passenger/crew 60 months or 7,000 60 months or 5,600

-325 airplanes. doors, the upper and lower flight cycles, flight cycles,

edges of the door frame whichever occurs whichever occurs

panel cutout. first. first.

Repetitive Inspections of Corner Doublers, Fail-Safe Ring, and Door Frames

Repetitive Inspections of Corner Doublers, Fail-Safe Ring, and Door Frames

(h) Do inspections (i.e., rotating probe, x-ray, and general visual, as applicable) for cracks of the holes of the corner doublers, the fail-safe ring, and the door frames of the passenger/ crew door structures, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-53-2037, Revision 02, dated November 27, 2000. Do the inspections at the applicable times specified in paragraphs (h)(1) through (h)(3) of Table 3 of this AD, until the modification required by paragraph (k) of this AD is done.

Table 3.--Compliance Time Requirements for Repetitive Inspections of

Corner Doublers, Fail-Safe Ring, and Door Frames

For-- Inspect-- And--

(1) The upper corners of the Before the Do rotating probe

forward doors. accumulation of inspections at

20,000 total flight intervals not to

cycles, or within exceed 6,000 flight

2,000 flight cycles cycles.

after the effective

date of this AD,

whichever occurs

later.

(2) The lower corners of the Before the Do rotating probe

forward doors. accumulation of inspections at

20,000 total flight intervals not to

cycles, or within exceed 10,000

4,000 flight cycles flight cycles.

after the effective

date of this AD,

whichever occurs

later.

(3) The upper and lower Before the Do rotating probe

corners and parts accumulation of inspections at

underneath the corners of 20,000 total flight intervals not to

the upper door frames of cycles, or within exceed 8,000 flight

the aft doors. 4,000 flight cycles cycles or do x-ray

after the effective inspections at

date of this AD, intervals not to

whichever occurs exceed 3,500 flight

later. cycles; and do

general visual

inspections of

areas around

fasteners in

vicinity of

stringer 12 of the

upper door frames

at intervals not to

exceed 6,900 flight

cycles.

Note 1: For the purposes of this AD, a general visual inspection is: "A visual examination of an interior or exterior area, installation, or assembly to detect obvious damage, failure, or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight, or droplight and may require removal or opening of access panels or doors. Stands, ladders, or platforms may be required to gain proximity to the area being checked."

Corrective Actions

Corrective Actions

(i) If any crack or corrosion is found during any inspection required by this AD, before further flight, do the applicable corrective action in paragraph (i)(1) through (i)(3) of Table 4 of this AD, except as provided by paragraph (j) of this AD.

Table 4.--Corrective Actions

In accordance with

If-- Then-- the accomplishment

instructions of--

(1) Any crack or corrosion Repair the cracked Airbus Service

is found during any or corroded part. Bulletin A310-53-

inspection required by 2030, Revision 06,

paragraph (f) of this AD. dated July 2, 1996.

(2) Any crack or corrosion Repair the cracked Airbus Service

is found during any or corroded part. Bulletin A310-53-

repetitive inspection 2041, Revision 02,

required by paragraph (g) dated July 2, 1996.

of this AD.

(3) Any crack is found Repair the cracked Airbus Service

during any inspection part. Bulletin A310-53-

required by paragraph (h) 2037, Revision 02,

of this AD. dated November 27,

2000.

(j) If any crack or corrosion is found during any inspection required by this AD, and the service bulletin recommends contacting Airbus for appropriate action: Before further flight, repair the cracked or corroded part in accordance with a method approved by either the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate; or the Direction Générale de l'Aviation Civile (DGAC) (or its delegated agent).

Terminating Modification for Repetitive Inspection of Corner Doublers, Fail-Safe Ring, and Door Frames

Terminating Modification for Repetitive Inspection of Corner Doublers, Fail-Safe Ring, and Door Frames

(k) Modify the passenger/crew door structures in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-53-2017, Revision 09, dated May 17, 2004. Do the modification at the applicable time in paragraph (k)(1) or (k)(2) of Table 5 of this AD. Accomplishment of this modification constitutes terminating action for the repetitive inspections required by paragraph (h) of this AD. The inspections required by paragraph (f) of this AD must be done before accomplishing this modification.

Table 5.--Compliance Time for Terminating Modification

For model-- Compliance time

(1) A310-203, -204, -221, and -222 Before the accumulation of

airplanes. 40,000 flight cycles since the

date of issuance of the

original standard

Airworthiness Certificate or

the date of issuance of the

original Export Certificate of

Airworthiness, or during the

next inspection required by

paragraph (h) of this AD,

whichever occurs later.

(2) A310-304, -322, -324, and -325 Before the accumulation of

airplanes. 35,000 flight cycles since the

date of issuance of the

original standard

Airworthiness Certificate or

the date of issuance of the

original Export Certificate of

Airworthiness, or during the

next inspection required by

paragraph (h) of this AD,

whichever occurs later.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(l)(1) The Manager, International Branch, ANM-116, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.

(2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office.

Related Information

Related Information

(m) French airworthiness directives 1991-132-124(B) R1, issued November 29, 2000, and F-2004-103, issued July 7, 2004, also address the subject of this AD.

Issued in Renton, Washington, on November 9, 2005. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.