Radar Vectors
Proposed Rule Proposed Issued Mar 8, 2004 6 pages Copy saved Nov 17, 2026

69 FR 10641 Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA proposes to revise an earlier NPRM airworthiness directive (AD) action that applies to certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. That proposed AD would have revised AD 2002-22-17, which currently requires you to repetitively inspect the inboard forward flap bellcranks for cracks and eventually replace these bellcranks on all Cessna Models 208 and 208B airplanes. The proposed AD would have provided the option of installing a newly designed bellcrank to increase the life limits and terminate the repetitive inspections. AD 2003-21-04 also requires inspections of the inboard forward flap bellcranks on these airplanes. The FAA has determined that additional inspections of the bellcranks are necessary on Cessna Models 208 and 208B airplanes. We believe that it would be less confusing if all of these actions were in one AD. Therefore, FAA proposes to supersede AD 2002-22-17 and AD 2003-21-04. Since the added actions from AD 2003-21-04 and other proposed inspections impose an additional burden over that proposed in the NPRM, we are reopening the comment period to allow the public the chance to comment on these additional actions.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 2002-CE-23-AD] RIN 2120-AA64

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Supplemental notice of proposed rulemaking (NPRM); reopening of the comment period.

Summary

SUMMARY: The FAA proposes to revise an earlier NPRM airworthiness directive (AD) action that applies to certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. That proposed AD would have revised AD 2002-22-17, which currently requires you to repetitively inspect the inboard forward flap bellcranks for cracks and eventually replace these bellcranks on all Cessna Models 208 and 208B airplanes. The proposed AD would have provided the option of installing a newly designed bellcrank to increase the life limits and terminate the repetitive inspections. AD 2003-21-04 also requires inspections of the inboard forward flap bellcranks on these airplanes. The FAA has determined that additional inspections of the bellcranks are necessary on Cessna Models 208 and 208B airplanes. We believe that it would be less confusing if all of these actions were in one AD. Therefore, FAA proposes to supersede AD 2002-22-17 and AD 2003-21-04. Since the added actions from AD 2003-21-04 and other proposed inspections impose an additional burden over that proposed in the NPRM, we are reopening the comment period to allow the public the chance to comment on these additional actions.

Dates

DATES: We must receive any comments on this proposed AD by May 17, 2004.

ADDRESSES: Use one of the following to submit comments on this proposed AD:

<bullet<ls-thn-eq> By mail: FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2002-CE-23-AD, 901 Locust, Room 506, Kansas City, Missouri 64106.

Addresses

<bullet<ls-thn-eq> By fax: (816) 329-3771.

<bullet<ls-thn-eq> By e-mail: [email protected]. Comments sent electronically must contain "Docket No. 2002-CE-23-AD" in the subject line. If you send comments electronically as attached electronic files, the files must be formatted in Microsoft Word 97 for Windows or ASCII.

You may get the service information identified in this proposed AD from Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67277; telephone: (316) 517-5800; facsimile: (316) 942-9006.

You may view the AD docket at FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2002-CE-23-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Office hours are 8 a.m. to 4 p.m., Monday through Friday, except Federal holidays.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Paul Nguyen, Aerospace Engineer, FAA, Wichita Aircraft Certification Office ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4125; facsimile: 816-946-4107.

SUPPLEMENTARY INFORMATION:

Comments Invited

How Do I Comment on This Proposed AD?

How Do I Comment on This Proposed AD?

We invite you to submit any written relevant data, views, or arguments regarding this proposal. Send your comments to an address listed under ADDRESSES. Include "AD Docket No. 2002-CE-23-AD" in the subject line of your comments. If you want us to acknowledge receipt of your mailed comments, send us a self-addressed, stamped postcard with the docket number written on it. We will date-stamp your postcard and mail it back to you.

Are There Any Specific Portions of This Proposed AD I Should Pay Attention To?

Are There Any Specific Portions of This Proposed AD I Should Pay Attention To?

We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. If you contact us through a nonwritten communication and that contact relates to a substantive part of this proposed AD, we will summarize the contact and place the summary in the docket. We will consider all comments received by the closing date and may amend this proposed AD in light of those comments and contacts.

Discussion

Discussion

What Events Have Caused This Proposed AD?

The need to reduce the life limit and repetitively inspect the inboard forward flap bellcrank on Cessna Models 208 and 208A airplanes caused us to issue AD 2002-22-17, Amendment 29-12944 (67 FR 68508, November 12, 2002).

Since FAA issued AD 2002-22-17, Cessna has designed a new flap bellcrank, part number (P/N) 2622311-7, with a life limit of 40,000 landings (instead of 7,000 landings). The new flap bellcrank (P/N 2622311-7) may be substituted for the older flap bellcranks, P/N 2622281-2, 2622281-12, or 2692001-2. Installation of this new flap bellcrank will eliminate the need for repetitive inspections.

Has FAA Taken Any Action to This Point?

Has FAA Taken Any Action to This Point?

We issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to all Cessna Models 208 and 208B airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on July 28, 2003 (68 FR 44252). The NPRM proposed to revise AD 2002-22-17 by proposing a new AD that would:

--Retain the requirements of AD 2002-22-17; and --Provide the option of installing the 40,000 landings life limit bellcranks.

Was the Public Invited To Comment?

Was the Public Invited To Comment?

The FAA encouraged interested persons to participate in developing this amendment. We did not receive any comments on the proposed rule or on our determination of the cost to the public.

What Events Have Caused FAA To Issue a Supplemental NPRM?

What Events Have Caused FAA To Issue a Supplemental NPRM?

The FAA recently issued AD 2003-21-04, Amendment 39-13339 (68 FR 59707, October 17, 2003) to require you to immediately inspect certain inboard forward flap bellcranks for cracks, deformation, and missing/ incomplete welds. If cracks, deformation, or missing/incomplete welds are found, the AD would require you to immediately replace the flap bellcrank or temporarily incorporate certain flap limitations.

In addition, FAA has identified other bellcranks within the flap system that require inspection. The FAA has determined that all of the inspections and replacements of the bellcranks should be included in one AD. These inspections are referenced in Cessna Caravan Service Bulletin CAB03-11, Revision 1, dated September 24, 2003.

FAA's Determination and Requirements of This Proposed AD

FAA's Determination and Requirements of This Proposed AD

What Has FAA Decided?

After examining the circumstances and reviewing all available information related to the incidents described above, we have determined that: --The unsafe condition referenced in this document exists or could develop on other Cessna Models 208 and 208B airplanes of the same type design that are on the U.S. registry; --We should combine the actions of AD 2002-22-17, AD 2003-21-04, and those referenced in Cessna Caravan Service Bulletin CAB03-11, Revision 1, dated September 24, 2003; and --We should take AD action to correct this unsafe condition.

The Supplemental NPRM

The Supplemental NPRM

How Will the Changes to the NPRM Impact the Public?

Adding the inspection and replacement requirements from both AD 2003-21-04 and Cessna Caravan Service Bulletin CAB03-11, Revision 1, dated September 24, 2003, goes beyond the scope of what was originally proposed in the NPRM. Therefore, we are reopening the comment period and allowing the public the chance to comment on these additional actions.

What Are the Provisions of the Supplemental NPRM?

What Are the Provisions of the Supplemental NPRM?

The proposed AD would supersede AD 2002-22-17 and AD 2003-21-04 by requiring you to: --Do all current requirements of AD 2002-22-17; --Provide the option of installing the 40,000 landings life limit bellcranks; --Inspect all bellcranks for cracks, deformation, and missing/ incomplete welds; and --If cracks, deformation, or missing/incomplete welds are found, the AD would require you to immediately replace the bellcrank or temporarily incorporate certain flap limitations.

How Does the Revision to 14 CFR Part 39 Affect This Proposed AD?

How Does the Revision to 14 CFR Part 39 Affect This Proposed AD?

On July 10, 2002, we published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs FAA's AD system. This regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.

Costs of Compliance

Costs of Compliance

How Many Airplanes Would This Proposed AD Impact?

We estimate that this proposed AD affects 1,300 airplanes in the U.S. registry.

What Would Be the Cost Impact of This Proposed AD on Owners/Operators of the Affected Airplanes?

For the proposed actions retained from AD 2003-21-04, and the addition of all bellcranks to the applicability, we estimate the following costs to do this proposed inspection:

What Would Be the Cost Impact of This Proposed AD on Owners/Operators of the Affected Airplanes?

Total cost

Labor cost Parts cost per Total cost on U.S. operators

airplane

2 workhours x $65 per hour = $130.. No cost for parts.... $130 $130 x 1,300 for = $169,000.

We estimate the following costs to do any necessary replacements of the right inboard forward flap bellcrank (P/N 2622311-7, alternate P/N 2622311-16) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

3 workhours x $65 per hour = $195 … $1,845 $195 + $1,845 = $2,040.

We estimate the following costs to do any necessary replacements of the left inboard forward flap bellcrank (P/N 2622281-1) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $1,201 $65 + $1,201 = $1,266.

We estimate the following costs to do any necessary replacements of the right inboard aft flap bellcrank (P/N 2622267-8) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $1,273 $65 + $1,273 = $1,338.

We estimate the following costs to do any necessary replacements of the left inboard aft flap bellcrank (P/N 2622267-7) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $2,098 $65 + $2,098 = $2,163.

We estimate the following costs to do any necessary replacements of the left outboard flap bellcrank (P/N 2622091-17) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $627 $65 + $627 = $692.

We estimate the following costs to do any necessary replacements of the right outboard flap bellcrank (P/N 2622091-18) that would be required based on the results of this proposed inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $661 $65 + $661 = $726.

For the proposed requirements from AD 2002-22-17 that you repetitively inspect the inboard forward flap bellcranks for cracks, eventually replace these bellcranks, and provides the option of installing the new design flap bellcrank to increase the life limits and terminate the repetitive inspections, we estimate the following costs to do the proposed inspection:

Total cost

Labor cost Parts cost per Total cost on U.S. operators

airplane

1 workhour x $65 per hour = $65 … No cost for parts … $65 $65 x 1,300 = $84,500.

We estimate the following costs to do any proposed replacements using the same flap bellcrank (P/N 2622281-2, 2622281-12, 2692001-2, or FAA-approved equivalent P/N) that will be required based on the proposed inspection or the reduced life limits:

Labor cost Parts cost Total cost per airplane Total cost on U.S. operators

3 workhours x $65 per hour = $195... $1,793 … $195 + $1,793 = $1,988 $1,988 x 1,300 = $2,584,400.

We estimate the following costs to do any proposed replacements using the new flap bellcrank (P/N 2622311-7 or FAA-approved equivalent P/N) that will be required based on the proposed inspection or the reduced life limits. We have no way of determining the number of airplanes that may need this proposed replacement with the new flap bellcrank:

Labor cost Parts cost Total cost per airplane

3 workhours x $65 per hour = $195 … $1,845 $195 + $1,845 = $2,040.

What Is the Difference Between the Cost Impact of This Proposed AD and the Cost Impacts of AD 2003-21-04 and AD 2002-22-17?

What Is the Difference Between the Cost Impact of This Proposed AD and the Cost Impacts of AD 2003-21-04 and AD 2002-22-17?

AD 2003-21-04 already established the inspection and replacement of the right inboard forward flap bellcrank assembly on the affected airplanes. Therefore, the replacement is already required through that AD. The only difference in the cost impact on the public of this proposed AD and AD 2003-21-04 is the additional cost for the inspection of all other bellcranks, and, if necessary, replacement.

AD 2002-22-17 already established the life limit for the flap bellcrank (P/N 2622281-2, 2622281-12, 2692001-2, or FAA-approved equivalent P/N) on the affected airplanes. Therefore, the replacement is already required through that AD. The only difference in the cost impact upon the public of this AD and AD 2002-22-17 is the additional $52 cost difference for the new flap bellcrank.

Regulatory Findings

Regulatory Findings

Would This Proposed AD Impact Various Entities?

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

For the reasons discussed above, I certify that this proposed AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this proposed AD and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "AD Docket No. 2002-CE-23-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing both Airworthiness Directive (AD) 2002-22-17, Amendment 39-12944, and AD 2003-21-04, Amendment 39-13339; and by adding the following new AD: Cessna Aircraft Company: Docket No. 2002-CE-23-AD

When Is the Last Date I Can Submit Comments on This Proposed AD?

When Is the Last Date I Can Submit Comments on This Proposed AD?

(a) We must receive comments on this proposed airworthiness directive (AD) by May 17, 2004.

What Other ADs Are Affected By This Action?

(b) This AD supersedes AD 2002-22-17 and AD 2003-21-04.

What Airplanes Are Affected by This AD?

What Airplanes Are Affected by This AD?

(c) This AD affects the following airplane models and serial numbers that are certificated in any category:

(1) Group 1 (retains the actions from AD 2003-21-04, and adds all flap bellcranks to the applicability):

Model Serial Numbers

208 … 20800001 through 20800369.

208B … 208B0001 through 208B1014,

208B1017, 208B1018, 208B1020

through 208B1024, 208B1026,

and 208B1029 through 208B1033.

(2) Group 2 (retains the requirement of AD 2002-22-17 that you repetitively inspect the inboard forward flap bellcranks for cracks, eventually replace these bellcranks, and provides the option of installing the new design flap bellcrank to increase the life limits and terminate the repetitive inspections): Models 208 and 208B airplanes, all serial numbers.

What Is the Unsafe Condition Presented in This AD?

What Is the Unsafe Condition Presented in This AD?

(d) The actions specified in this AD are intended to prevent failure of any bellcrank due to cracks, deformation, or missing/ incomplete welds. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

What Must I Do To Address This Problem for Group 1 Airplanes?

What Must I Do To Address This Problem for Group 1 Airplanes?

(e) To address this problem for Group 1 airplanes, you must do the following:

Actions Compliance Procedures

(1) Inspect the right Within the next 25 Use a flashlight and

inboard forward flap landings after a mirror as

bellcrank assembly for October 21, 2003 necessary to see if

cracks, deformation, and (the effective date welds (1), (4),

missing/incomplete welds. of AD 2003-21-04). (5), and (6) exist

The affected flap bellcrank If landings are and are at least

incorporates one of the unknown, then you 0.06-inch thick

following part numbers (P/ may multiply hours around the full

N): time-in-service circumference of

(i) P/N 2622083-18; (TIS) by 1.25. For the shaft. These

(ii) P/N 2622281-2; the purposes of welds and the

(iii) P/N 2692001-2; or this AD, you may inspection

(iv) P/N 2622281-12. substitute 20 hours procedures are

TIS for 25 landings. referenced in

Figure 1, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

CAB03-11, Revision

1, dated September

24, 2003.

(2) Inspect the left Within the next 25 Use a flashlight and

inboard forward bellcrank landings after the a mirror as

for cracks, deformation, effective date of necessary to see if

and missing/incomplete this AD. If welds (1) through

welds. The affected flap landings are (4) exist and are

bellcrank incorporates one unknown, then you at least 0.06-inch

of the following part P/Ns: may multiply hours thick around the

(i) P/N 2622083-15; or TIS by 1.25. For full circumference

(ii) P/N 2622281-1. the purposes of of the shaft. These

this AD, you may welds and the

substitute 20 hours inspection

TIS for 25 landings. procedures are

referenced in

Figure 2, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

CAB03-11, Revision

1, dated September

24, 2003.

(3) Inspect the inboard aft Within the next 25 Use a flashlight and

bellcrank for cracks, landings after the a mirror as

deformation, and missing/ effective date of necessary to see if

incomplete welds. The this AD. If welds (1), (2),

affected flap bellcrank landings are (4), and (5) exist

incorporates one of the unknown, then you and are at least

following P/Ns: may multiply hours 0.05-inch thick

(i) P/N 2622267-1; or TIS by 1.25. For around the full

(ii) P/N 2622267-2; the purposes of circumference of

(iii) P/N 2622267-7; this AD, you may the shaft. These

(iv) P/N 2622267-8; substitute 20 hours welds and the

(v) P/N 2622083-1; or TIS for 25 landings. inspection

(vi) P/N 2622083-2. procedures are

referenced in

Figure 3, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

CAB03-11, Revision

1, dated September

24, 2003.

(4) Inspect the outboard Within the next 25 Use a flashlight

bellcrank for cracks, landings after the and a mirror as

deformation, and missing/ effective date of necessary to see if

incomplete welds. The this AD. If welds (1) through

affected flap bellcrank landings are (4) exist and are

incorporates one of the unknown, then you at least 0.05-inch

following P/Ns: may multiply hours thick around the

(i) P/N 2622091-1; or TIS by 1.25. For full circumference

(ii) P/N 2622091-2; the purposes of of the shaft. These

(iii) P/N 2622091-9; this AD, you may welds and the

(iv) P/N 2622091-10; substitute 20 hours inspection

(v) P/N 2622091-17; or TIS for 25 landings. procedures are

(iv) P/N 2622091-18. referenced in

Figure 4, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

CAB03-11, Revision

1, dated September

24, 2003.

(5) If you find cracks, Replace or do the Replacement: Use

deformation, or missing/ flap prohibition the Accomplishment

incomplete welds during the actions before Instructions of

inspection required by further flight Cessna Caravan

paragraphs (e)(1) through after the Service Bulletin

(e)(4) of this AD, then do inspection required No.: CAB02-12,

one of the following: in paragraphs Revision 1, dated

(i) Replace the bellcrank (e)(1) through January 27, 2003,

with a new bellcrank; or (e)(4) of this AD. and the

(ii) Prohibit the use of If you choose the Accomplishment

flaps through the actions flap prohibition, Instructions of

of paragraph (g) of this you must have the Cessna Caravan

AD. replacement done Service Kit No.:

within 200 hours SK208-148A, dated

TIS after the January 27, 2003,

inspection required or refer to the

by paragraphs Maintenance Manual,

(e)(1) through Chapter 27, Flap

(e)(4) of this AD. System--Maintenance

After the new flap Practices, for

bellcrank is bellcrank removal

installed, the and installation

Temporary Revision procedures

208PHTR02, dated Flap Prohibition:

September 23, 2003, Use the information

should be removed. in the Temporary

Revision 208PHTR02,

dated September 23,

2003. The action is

referenced in

Cessna Caravan

Service Bulletin

CAB03-11, Revision

1, dated September

24, 2003.

What Must I Do To Address This Problem for Group 2 Airplanes?

What Must I Do To Address This Problem for Group 2 Airplanes?

(f) To address this problem for Group 2 airplanes, you must do the following:

Actions Compliance Procedures

(1) Repetitive Inspections: Initially inspect Follow the

Inspect, using eddy current upon the Inspection

methods, any inboard accumulation of Instructions of

forward flap bellcrank P/N 4,000 landings on Cessna Caravan

2622281-2, 2622281-12, the bellcrank or Service Bulletin

2692001-2, or FAA-approved within the next 250 No.: CAB02-1, dated

equivalent P/N) for cracks. landings after February 11, 2002,

December 31, 2002 and the applicable

(the effective date maintenance manual.

of AD 2002-22-17),

whichever occurs

later. Repetitively

inspect thereafter

at every 500

landings until

7,000 landings are

accumulated at

which time you must

replace as required

in paragraphs

(f)(2) and (f)(3)

of this AD. No

repetitive

inspections are

required when a P/N

2622311-7 (or FAA-

approved equivalent

P/N) inboard

forward flap

bellcrank is

installed.

(2) Initial Replacement: If cracks are Replacement: For

Replace any inboard forward found, replace or flap bellcrank (P/N

flap bellcrank (P/N 2622281- do the flap 2622281-2, 2622281-

2, 2622281-12, 2692001-2, prohibition actions 12, 2692001-2, or

or FAA-approved equivalent before further FAA-approved

P/N) with either: flight after the equivalent P/N):

(i) the same flap bellcrank inspection required Follow the

(i) the same flap bellcrank inspection required Follow the

(P/N 2622281-2, 2622281-12, in paragraphs Instructions of

2692001-2, or FAA-approved (f)(1) of this AD. Cessna Caravan

equivalent P/N); or If you choose the Service Bulletin

(ii) a new flap bellcrank flap prohibition, No.: CAB02-1, dated

(P/N 2622311-7 or FAA- you must have the February 11, 2002,

approved equivalent P/N). replacement done and the applicable

within 200 hours maintenance manual.

TIS after the For new flap

inspection required bellcrank (P/N

by paragraphs 2622311-7 or FAA-

(f)(1) of this AD. approved equivalent

After the new flap P/N): Follow the

bellcrank is Accomplishment

installed, the Instructions of

Temporary Revision Cessna Caravan

208PHTR02, dated Service Bulletin

September 23, 2003, No.: CAB02-12,

should be removed. Revision 1, dated

If cracks are not January 27, 2003,

found, initially and the

replace at Accomplishment

whichever occurs Instructions of

later: Upon the Cessna Caravan

accumulation of Service Kit No.

7,000 landings on SK203-148A, dated

the bellcrank or January 27, 2003.

within the next 75 Flap Prohibition:

landings after Use the information

December 31, 2002 in the Temporary

(the effective date Revision 208PHTR02,

of AD 2002-22-17). dated September 23,

2003.

(3) Life Limits (Repetitive Replace at the Use the service

Replacements): applicable information

(i) The life limit for the referenced life referenced in

inboard forward flap limits. paragraph (f)(2) of

bellcranks (P/N 2622281-2, this AD.

2622281-12, 2692001-2, or FAA-approved equivalent P/ N) is 7,000 landings. Repetitive inspections every 500 landings begin at 4,000 landings (see paragraph (f)(1) of this AD). (ii) The life limit for the inboard forward flap bellcranks (P/N 26222311-7 or FAA-approved equivalent P/N) is 40,000 landings. No repetitive inspections are required on these bellcranks.

Note 1: Inboard forward flap bellcranks (P/N 2622281-2, 2622281-12, or 2692001-2) with 7,000 landings or more do not have to be replaced until 75 landings after December 31, 2002 (the effective date of AD 2002-22-17), unless found cracked.

Note 2: The compliance times of this AD are presented in landings instead of hours TIS. If the number of landings is unknown, hours TIS may be used by multiplying the number of hours TIS by 1.25.

What Are the Actions I Must Do if I Choose the Flap Prohibition Option?

(g) Insert Temporary Revision, 208PHTR02, dated September 23, 2003, into the applicable pilot's operating handbook and FAA-approved airplane flight manual. The owner/operator holding at least a private pilot certificate as authorized by § 43.7 of the Federal Aviation Regulations (14 CFR 43.7) may incorporate this information into the AFM. Make an entry into the aircraft records showing compliance with this portion of the AD in accordance with section 43.9 of the Federal Aviation Regulations (14 CFR 43.9).

What Are the Actions I Must Do if I Choose the Flap Prohibition Option?

(1) This procedure applies to Cessna Models 208 and 208B landplanes. For other FAA-approved aircraft configurations (for example, amphibian, floatplanes, and so forth), you must operate with flaps up per the appropriate airplane flight manual supplement.

(2) This procedure allows for applicable deviation from the Master Minimum Equipment List (MMEL) for these airplanes until the flap bell crank is replaced. The applicable MMEL requirements go back into effect at the time of flap bell crank replacement.

May I Request an Alternative Method of Compliance?

May I Request an Alternative Method of Compliance?

(h) You may request a different method of compliance or a different compliance time for this AD by following the procedures in 14 CFR 39.13. Send your request to the Manager, Wichita Aircraft Certification Office (ACO), FAA. For information on any already approved alternative methods of compliance, contact Paul Nguyen, Aerospace Engineer, FAA, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4125; facsimile: 816-946-4107.

(i) Alternative methods of compliance approved under AD 2002-22-17 and AD 2003-21-04 are not approved for this AD.

May I Get Copies of the Documents Referenced in This AD?

May I Get Copies of the Documents Referenced in This AD?

(j) You may get copies of the documents referenced in this AD from Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67277; telephone: (316) 517-5800; facsimile: (316) 942-9006. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

Issued in Kansas City, Missouri, on March 2, 2004. Sandra J. Campbell, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.