Radar Vectors
Proposed Rule Proposed Issued Oct 24, 2003 5 pages Copy saved Nov 17, 2026

68 FR 60887 Airworthiness Directives; AeroSpace Technologies of Australia Pty Ltd. Models N22B, N22S, and N24A Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for all AeroSpace Technologies of Australia Pty Ltd. (ASTA) Models N22B, N22S, and N24A airplanes. This proposed AD would require you to repetitively inspect wing fittings for fatigue defects, replace or correct defective wing fittings, and replace the stub wing front spar assembly and wing fitting when fatigue life limits are reached. This proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. We are issuing this proposed AD to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 2003-CE-37-AD] RIN 2120-AA64

Airworthiness Directives; AeroSpace Technologies of Australia Pty Ltd. Models N22B, N22S, and N24A Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all AeroSpace Technologies of Australia Pty Ltd. (ASTA) Models N22B, N22S, and N24A airplanes. This proposed AD would require you to repetitively inspect wing fittings for fatigue defects, replace or correct defective wing fittings, and replace the stub wing front spar assembly and wing fitting when fatigue life limits are reached. This proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. We are issuing this proposed AD to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.

Dates

DATES: We must receive any comments on this proposed AD by December 4, 2003.

ADDRESSES: Use one of the following to submit comments on this proposed AD:

[sbull] By mail: FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-37-AD, 901 Locust, Room 506, Kansas City, Missouri 64106.

Addresses

[sbull] By fax: (816) 329-3771.

[sbull] By e-mail: [email protected]. Comments sent electronically must contain "Docket No. 2003-CE-37-AD" in the subject line. If you send comments electronically as attached electronic files, the files must be formatted in Microsoft Word 97 for Windows or ASCII.

You may get the service information identified in this proposed AD from Nomad Operations, Aerospace Support Division, Boeing Australia, PO Box 767, Brisbane, QLD 4000 Australia; telephone 61 7 3306 3366; facsimile 61 7 3306 3111.

You may view the AD docket at FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-37-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Office hours are 8 a.m. to 4 p.m., Monday through Friday, except Federal holidays.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Ron Atmur, Aerospace Engineer, FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 90712; telephone (562) 627-5224; facsimile (562) 627-5210.

SUPPLEMENTARY INFORMATION:

Comments Invited

How do I comment on this proposed AD? We invite you to submit any written relevant data, views, or arguments regarding this proposal. Send your comments to an address listed under ADDRESSES. Include "AD Docket No. 2003-CE-37-AD" in the subject line of your comments. If you want us to acknowledge receipt of your mailed comments, send us a self-addressed, stamped postcard with the docket number written on it. We will date-stamp your postcard and mail it back to you.

Comments Invited

Are there any specific portions of this proposed AD I should pay attention to? We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. If you contact us through a nonwritten communication and that contact relates to a substantive part of this proposed AD, we will summarize the contact and place the summary in the docket. We will consider all comments received by the closing date and may amend this proposed AD in light of those comments and contacts.

Discussion

Discussion

What events have caused this proposed AD? The Civil Aviation Safety Authority (CASA), which is the airworthiness authority for Australia, recently notified FAA that an unsafe condition may exist on all ASTA Models N22B, N22S, and N24A airplanes. The CASA reports that fatigue tests on the wing strut upper end fitting have shown premature failures and rapid crack growth. Also, fatigue tests on the wing strut lower end fittings, stub wing strut pick up fitting, and stub wing front spar assembly have identified appropriate fatigue lives for the respective parts.

What are the consequences if the condition is not corrected? Fatigue loading could result in failure of the wing strut upper end fitting, wing strut lower end fittings, stub wing strut pick up fitting, or stub wing front spar assembly. Such failure could lead to reduced structural capability or reduced controllability of the airplane.

Is there service information that applies to this subject? Boeing Australia (formerly ASTA) Aerospace Technologies of Australia has issued:

--Nomad Alert Service Bulletin No. ANMD-57-12, Revision 2, dated May 25, 1999; --Nomad Service Bulletin No. NMD-53-18, dated February 8, 1996; and --Nomad Service Bulletin No. NMD-53-18, Revision 1, dated September 3, 2002.

What are the provisions of this service information? The service bulletins include procedures for:

--Performing a fatigue inspection of the stub wing strut pick-up fittings for cracks; --Replacing the stub wing strut pick-up fittings; --Inspecting (visually) the strut to upper strut fittings bolt holes for scoring, ovality, fretting, corrosion, and dimensions; --Inspecting (eddy current method) the strut to upper strut fittings bolt holes for cracks; --Modifying (line ream) the strut to upper strut fitting bolt holes; --Replacing bolts for the strut upper end fittings; and --Replacing the strut upper end fittings.

What action did the CASA take? The CASA classified these service bulletins as mandatory and issued these Australian ADs in order to ensure the continued airworthiness of these airplanes in Australia:

--AD Number AD/GAF-N22/2, Amendment 3, dated January 28, 2003; and --AD Number AD/GAF-N22/70, Amendment 2, dated January 28, 2003.

FAA's Determination and Requirements of This Proposed AD

What has FAA decided? We have examined the CASA's findings, reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation in the United States.

FAA's Determination and Requirements of This Proposed AD

Since the unsafe condition described previously is likely to exist or develop on other ASTA Models N22B, N22S, and N24A airplanes of the same type design that are registered in the United States, we are proposing AD action to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.

What would this proposed AD require? This proposed AD would require you to incorporate the actions in the previously-referenced service bulletin.

How does the revision to 14 CFR part 39 affect this proposed AD? On July 10, 2002, we published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs FAA's AD system. This regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.

Costs of Compliance

Costs of Compliance

How many airplanes would this proposed AD impact? We estimate that this proposed AD affects 15 airplanes in the U.S. registry.

What would be the cost impact of this proposed AD on owners/ operators of the affected airplanes? We estimate the following costs to accomplish the proposed inspection of the wing strut upper end fitting bolt holes:

Total cost per

Labor cost Parts cost airplane Total cost on U.S. operators

12 workhours x $65 per hour = $780.... Not applicable … $780 15 x $780 = $11,700

We estimate the following costs to accomplish the proposed inspection of the stub wing strut pick up fittings:

Total cost per

Labor cost Parts cost airplane Total cost on U.S. operators

16 workhours x $65 per hour = $1,040.. Not applicable … $1,040 15 x $1,040 = $15,600

We estimate the following costs to accomplish any necessary replacements of the wing strut upper end fittings that would be required based on the results of the proposed inspection or on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:

Labor cost Parts cost Total cost per airplane

10 workhours x $65 per hour = $650 … $679 $650 + $679 = $1,329

We estimate the following costs to accomplish any necessary replacements of the wing strut lower end fittings that would be required based on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:

Labor cost Parts cost Total cost per airplane

12 workhours x $65 per hour = $780 … $193 $780 + $193 = $973

We estimate the following costs to accomplish any necessary replacements of the stub wing strut pick up fittings that would be required based on the results of the proposed inspection or on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:

Labor cost Parts cost Total cost per airplane

80 workhours x $65 per hour = $5,200 … $985 $5,200 + $985 = $6,185

We estimate the following costs to accomplish any necessary replacements of the stub wing front spar assembly that would be required based on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:

Labor cost Parts cost Total cost per airplane

370 workhours x $65 per hour = $24,050 … $4,820 $24,050 + $4,820 = $28,870

Regulatory Findings

Regulatory Findings

Would this proposed AD impact various entities? We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

Would this proposed AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this proposed AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this proposed AD and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "AD Docket No. 2003-CE-37-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

PART 39--AIRWORTHINESS DIRECTIVES

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

AeroSpace Technologies of Australia Pty Ltd.: Docket No. 2003-CE-37-AD

When Is the Last Date I Can Submit Comments on This Proposed AD Action?

When Is the Last Date I Can Submit Comments on This Proposed AD Action?

(a) We must receive comments on this proposed airworthiness directive (AD) action by December 4, 2003.

Are Any Other ADs Affected by This Action?

(b) None.

What Airplanes Are Affected by This AD?

(c) This AD affects Models N22B, N22S, and N24A airplanes, all serial numbers, that are certificated in any category.

What Is the Unsafe Condition Presented in This AD?

What Is the Unsafe Condition Presented in This AD?

(d) This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. The actions specified in this AD are intended to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.

What Must I Do To Address This Problem?

What Must I Do To Address This Problem?

(e) To address this problem, you must accomplish the following:

Actions Compliance Procedures

(1) Inspect the wing strut For Models N22S and Follow the

upper end fitting bolt N24A: Initially Accomplishment

holes: inspect before Instructions in

(i) Visually inspect for 3,600 hours time-in- Boeing Australia

scoring, ovality, fretting, service (TIS) on Aerospace

corrosion, and dimensions; the wing strut Technologies of

and upper end fitting Australia Nomad

(ii) Inspect, using eddy or within the next Alert Service

current inspection, for 100 hours TIS after Bulletin No. ANMD-

cracks. the effective date 57-12, Revision 2,

of this AD, dated May 25, 1999.

whichever occurs

later. Repetitively

inspect thereafter

at every 900 hours

TIS until 14,400

hours TIS are

accumulated on the

wing strut upper

end fitting. For

Model N22B:

Initially inspect

before 5,400 hours

TIS on the wing

strut upper end

fitting or within

the next 100 hours

TIS after the

effective date of

this AD, whichever

occurs later.

Repetitively

inspect thereafter

at every 1,200

hours TIS until

14,400 hours TIS

are accumulated on

the wing strut

upper end fitting.

(2) Complete corrective Before further Follow the

actions for defects of the flight after the Accomplishment

wing strut upper end inspection required Instructions in

fittings: in paragraph (e)(1) Boeing Australia

(i) If a crack is found or of this AD, unless Aerospace

the hole in the strut upper already Technologies of

end fitting is damaged and accomplished. Australia Nomad

will not clean up, replace Alert Service

the wing strut upper end Bulletin No. ANMD-

fittings. 57-12, Revision 2,

(ii) If the hole in the dated May 25, 1999;

strut is oval or damaged, and any repair

and the oversize line scheme obtained

reamer will not repair it:. from Nomad

(A) Get a repair scheme from Operations,

the manufacturer; and. Aerospace Support

(B) Follow this repair Division, Boeing

scheme.. Australia, PO Box

(iii) If scoring, fretting, 767, Brisbane, QLD

or corrosion is found, or 4000 Australia;

all dimensions are within telephone 61 7 3306

limits, line ream the hole 3366; facsimile 61

and replace the bolt. 7 3306 3111. Obtain

approval of this

repair scheme

through the FAA at

the address

specified in

paragraph (f) of

this AD.

(3) Replace the wing strut Before further Follow the

upper end fittings. flight when cracks Accomplishment

are found by the Instructions in

inspection required Boeing Australia

in paragraph Aerospace

(e)(1); and upon Technologies of

the accumulation of Australia Nomad

14,400 hours TIS on Alert Service

the fitting or Bulletin No. ANMD-

within the next 100 57-12, Revision 2,

hours TIS after the dated May 25, 1999.

effective date of

this AD, whichever

occurs later. For

Models N22S and

N24A: start

repetitive

inspections of

paragraph (e)(1) of

this AD when 7,200

hours TIS are

accumulated on the

wing strut upper

end fitting. For

Models N22B: start

repetitive

inspections of

paragraph (e)(1) of

this AD when 10,800

hours TIS are

accumulated on the

wing strut upper

end fitting.

(4) Replace the wing strut Upon the Follow a repair

lower end fittings: accumulation of scheme from Nomad

(i) Get a repair scheme from 14,000 hours TIS on Operations,

the manufacturer; and. the fitting or Aerospace Support

(ii) Follow this repair within the next 100 Division, Boeing

scheme.. hours TIS after the Australia, PO Box

effective date of 767, Brisbane, QLD

this AD, whichever 4000 Australia;

occurs later. telephone 61 7 3306

3366; facsimile 61

7 3306 3111. Get

approval of this

repair scheme

through the FAA at

the address

specified in

paragraph (f) of

this AD.

(5) Inspect the stub wing Initially inspect Follow the

strut pick up fittings for upon the Accomplishment

cracks. accumulation of Instructions in

5,400 hours TIS on Aerospace

the fitting or Technologies of

within the next 300 Australia Nomad

hours TIS on the Service Bulletin

fitting after the No. NMD-53-18,

effective date of dated February 8,

this AD, whichever 1996; or Boeing

occurs later. Australia Aerospace

Repetitively Technologies of

inspect thereafter Australia Nomad

at every 1,800 Service Bulletin

hours TIS until No. NMD-53-18,

18,800 hours TIS Revision 1, dated

are accumulated on September 3, 2002;

the stub wing strut and the applicable

pick up fitting. airplane

maintenance manual.

(6) Replace the stub wing Before further Follow the

strut pick up fittings. flight when cracks Accomplishment

are found after the Instructions in

inspection required Aerospace

in paragraph (e)(5) Technologies of

of this AD, unless Australia Nomad

already Service Bulletin

accomplished; and No. NMD-53-18,

upon the dated February 8,

accumulation of 1996; or Boeing

18,800 hours TIS or Australia Aerospace

300 hours TIS after Technologies of

the effective date Australia Nomad

of this AD, Service Bulletin

whichever occurs No. NMD-53-18,

later. Revision 1, dated

September 3, 2002;

and the applicable

airplane

maintenance manual.

(7) Replace the stub wing Upon the Follow a repair

front spar assembly: accumulation of scheme from Nomad

(i) Get a repair scheme from 25,000 hours TIS on Operations,

the manufacturer; and. the fitting or Aerospace Support

(ii) Follow this repair within the next 100 Division, Boeing

scheme.. hours TIS after the Australia, PO Box

effective date of 767, Brisbane, QLD

this AD, whichever 4000 Australia;

occurs later. telephone 61 7 3306

3366; facsimile 61

7 3306 3111. Get

approval of this

repair scheme

through the FAA at

the address

specified in

paragraph (f) of

this AD.

What About Alternative Methods of Compliance?

(f) You may request a different method of compliance or a different compliance time for this AD by following the procedures in 14 CFR 39.13. Send your request to the Manager, Los Angeles Aircraft Certification Office, FAA. For information on any already approved alternative methods of compliance, contact Ron Atmur, Aerospace Engineer, FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 90712; telephone (562) 627-5224; facsimile (562) 627-5210.

How Do I Get Copies of the Documents Referenced in This AD?

How Do I Get Copies of the Documents Referenced in This AD?

(g) You may get copies of the documents referenced in this AD from Nomad Operations, Aerospace Support Division, Boeing Australia, PO Box 767, Brisbane, QLD 4000 Australia; telephone 61 7 3306 3366; facsimile 61 7 3306 3111. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

Is There Other Information That Relates to This Subject?

Is There Other Information That Relates to This Subject?

(h) These Australian ADs also address the subject of this AD: AD Number AD/GAF-N22/2, Amendment 3, dated January 28, 2003, and AD Number AD/GAF-N22/70, Amendment 2, dated January 28, 2003.

Issued in Kansas City, Missouri, on October 20, 2003. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.