Radar Vectors
Proposed Rule Proposed Issued Oct 25, 2002 3 pages Copy saved Nov 17, 2026

67 FR 65524 Flight Simulation Device Initial and Continuing Qualification and Use; Correction

This document makes a correction to the proposed rule published in the Federal Register on September 25, 2002 (67 FR 60284), which proposes to establish flight simulation device qualification requirements in a new part. The FAA inadvertently omitted a table in the original NPRM.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 60

[Docket No. FAA-2002-12461; Notice No. 02-11] RIN 2120-AH07

Flight Simulation Device Initial and Continuing Qualification and Use; Correction

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM); correction.

SUMMARY: This document makes a correction to the proposed rule published in the Federal Register on September 25, 2002 (67 FR 60284), which proposes to establish flight simulation device qualification requirements in a new part. The FAA inadvertently omitted a table in the original NPRM.

Dates

DATES: Send your comments on or before December 24, 2002.

ADDRESSES: Address your comments to the Docket Management System, U.S. Department of Transportation, Room Plaza 401, 400 Seventh Street, SW., Washington, DC 20590-0001. You must identify the docket number FAA-2002-12461 at the beginning of your comments, and you should submit two copies of your comments. If you wish to receive confirmation that FAA received your comments, include a self-addressed, stamped postcard.

Addresses

You may also submit comments through the Internet to http://dms.dot.gov. You may review the public docket containing comments to these proposed regulations in person in the Dockets Office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Dockets Office is on the plaza level of the NASSIF Building at the Department of Transportation at the above address. Also, you may review public dockets on the Internet at http://dms.dot.gov.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Edward Cook, National Simulator Program Staff (AFS-205), Flight Standards Service, Federal Aviation Administration, 1701 Columbia Avenue, College Park, GA 30337; telephone (404) 305-6100.

SUPPLEMENTARY INFORMATION: On September 25, 2002, the FAA published Notice No. 02-11, Flight Simulation Device Initial and Continuing Qualification and Use (67 FR 60284). The NPRM proposed to amend the regulations to establish flight simulation device qualification requirements for all certificate holders in a new part. The FAA inadvertently omitted a table entitled "Table of Alternative Source Data FTD Levels 2, 3, and 5. Single Engine (Turbo-Propeller) Airplane." The table provides a range of performance that is typical for single engine, turbo-propeller powered airplanes for the indicated objective tests located in Attachment 2 of appendix B to part 60.

Correction

Correction

In proposed rule FR Doc. 02-14785, published on September 25, 2002 (67 FR 60284), make the following corrections:

PART 60--[CORRECTED]

Appendix B to part 60--[Corrected]

1. On page 60403, in Attachment 2 to appendix B to part 60, immediately following Figure 6. Small, Multi-Engine (Reciprocating) Airplane, Rudder Pedal Position vs. Force, add the following table: Attachment 2 to appendix B to part 60--Flight Training Device (FTD) Objective Tests * * * * *

Table of Alternative Source Data FTD Levels 2, 3, and 5. Single Engine

Table of Alternative Source Data FTD Levels 2, 3, and 5. Single Engine

(Turbo-Propeller) Airplane

QPS Requirement

Applicable Test and Test Number Authorized Performance Range

2. Performance

a. Takeoff.

(1) Ground acceleration time; brake 20-30 Seconds.

release to liftoff speed.

b. Climb.

2. Performance

(1) Normal climb with nominal gross Climb airspeed = 95-115 knots.

weight, at best rate-of-climb Climb rate = 800-1800 fpm (4-9

airspeed. m/sec).

c. Ground Deceleration.

(1) Deceleration time from 80 knots 20-35 Seconds.

to zero; with a nominal gross

weight; using wheel brakes on a

dry runway.

d. Engines.

(1) Acceleration; idle to takeoff 4-8 Seconds.

power.

(2) Deceleration; takeoff power to 3-7 Seconds.

idle.

3. Handling Qualities.

a. Static Control Checks.

(1)(b) Column position vs. force... Plot of Column Position vs.

Force must fall within the

shaded areas shown in Figure 7

of this appendix (Single

Engine [Turbo-Propeller]

Airplanes).

(2)(b) Wheel position vs. force.... Plot of Wheel Position vs.

Force must fall within the

shaded areas shown in Figure 8

of this appendix (Single

Engine [Turbo-Propeller]

Airplanes).

(3)(b) Pedal position vs. force.... Plot of Rudder Pedal Position

vs. Force must fall within the

shaded areas shown in Figure 9

of this appendix (Single

Engine [Turbo-Propeller]

Airplanes).

(4) Nosewheel steering force … Plot of Rudder Pedal Position

vs. Force must fall within the

shaded areas shown in Figure 9

of this appendix (Single

Engine [Turbo-Propeller]

Airplanes).

(5) Rudder pedal steering 10-30 degrees of nosewheel

calibration with full rudder pedal angle, both sides of neutral.

travel.

(8) Brake pedal position vs. force; 50-100 lbs (22-44 daN) of

at maximum pedal deflection. force.

b. Longitudinal.

(1) Power change force.

(a) Trim for straight and level 8 lbs (3.5 daN) of Push force

flight at 80% of normal cruise to 8 lbs (3.5 daN) of Pull

airspeed with necessary power. force.

Reduce power to flight idle.

Do not change trim or

configuration. After

stabilized, record column

force necessary to maintain

original airspeed; or

(b) Trim for straight and level 12-22 lbs (5.3-9.7 daN) of

flight at 80% of normal cruise force (Push).

airspeed with necessary power.

Add power to maximum setting.

Do not change trim or

configuration. After

stabilized, record column

force necessary to maintain

original airspeed.

(2) Flap/slat change force.

(a) Trim for straight and level 5-15 lbs (2.2-6.6 daN) of force

flight with flaps fully (Pull).

retracted at a constant

airspeed within the flaps-

extended airspeed range. Do

not adjust trim or power.

Extend the flaps to 50% of

full flap travel. After

stabilized, record stick force

necessary to maintain original

airspeed; or

(b) Trim for straight and level 5-15 lbs (2.2-6.6 daN) of force

flight with flaps extended to (Push).

50% of full flap travel, at a

constant airspeed within the

flaps-extended airspeed range.

Do not adjust trim or power.

Retract the flaps to zero

(fully retracted). After

stabilized, record stick force

necessary to maintain original

airspeed.

(3) Gear change force.

(a) Trim for straight and level 2-12 lbs (0.88-5.3 daN) of

flight with landing gear force (Pull).

retracted at a constant

airspeed within the landing

gear-extended airspeed range.

Do not adjust trim or power.

Extend the landing gear. After

stabilized, record stick force

necessary to maintain original

airspeed; or

(b) Trim for straight and level 2-12 lbs (0.88-5.3 daN) of

flight with landing gear force (Push).

extended, at a constant

airspeed within the landing

gear-extended airspeed range.

Do not adjust trim or power.

Retract the landing gear.

After stabilized, record stick

force necessary to maintain

original airspeed..

(4) Gear and flap operating times.

(a) Extend gear … 2-12 seconds.

(b) Retract gear … 2-12 seconds.

(c) Extend flaps, zero to 50% (c) 3-13 seconds.

travel.

(d) Retract flaps, 50% travel (d) 3-13 seconds.

to zero.

(5) Longitudinal trim … Must be able to trim

longitudinal stick force to

"zero" in each of the

following configurations: (a)

cruise; (b) approach; and (c)

landing.

(7) Longitudinal static stability.. Must exhibit positive static

stability.

(8) Stall warning (actuation of

stall warning device) with nominal

gross weight; wings level; clean

configuration, and a deceleration

rate of approximately one (1) knot

per second.

(a) Landing configuration … 60-90 knots; +/- 5 degrees of

bank.

(b) Clean configuration … Landing configuration speed, +

10-20 percent.

(9)(b) Phugoid dynamics … Must have a phugoid with a

period of 30-60 seconds; and

may not reach \1/2\ or double

amplitude in less than 2

cycles.

c. Lateral Directional.

(1) Roll response.

Roll rate must be measured Must have a roll rate of 6-40

through at least 30 degrees of degrees/second.

roll. Aileron control must be

deflected 50 percent of

maximum travel.

(2) Response to roll controller

step input.

Trim for straight and level Roll rate must decrease to not

flight at nominal gross weight more than 10 percent of the

and approach airspeed. Roll roll rate achieved, within 1-3

into a 30 degree bank turn and seconds of control release.

stabilize. When ready, input a

50 percent aileron control

opposite to the direction of

turn. When reaching zero bank

angle, rapidly neutralize the

aileron control and release.

Record the response from at

least 2 seconds prior to the

initiation of control input

opposite to the direction of

turn until at least 20 seconds

after neutralization of the

controls.

(3)(a) and (b) Spiral stability.

Cruise configuration and normal Initial bank angle (+/- 5

cruise airspeed. Establish a degrees) after 20 seconds.

20-30 degree bank. When

stabilized, neutralize the

aileron control and release.

Must be completed in both

directions of turn.

(4)(b) Rudder response.

Use 50 percent of maximum 6-12 degrees/second yaw rate.

rudder deflection. Applicable

to approach or landing

configuration.

(5)(b) Dutch roll, yaw damper off.

Applicable to cruise and A period of 2-5 seconds; and \1/

approach configurations. 2\-3 cycles.

(6) Steady state sideslip.

Use 50 percent rudder 2-10 degrees of bank; 4-10

deflection; Applicable to degrees of sideslip; and 2-10

approach and landing degrees of aileron.

configurations.

4. Cockpit Instrument Response.

Instrument systems response to an 300 milliseconds or less.

abrupt pilot controller input. One test is required in each axis (pitch, roll, and yaw).

* * * * *

Issued in Washington, DC, on October 18, 2002. Donald P. Byrne, Assistant Chief Counsel for Regulations.