Radar Vectors
Proposed Rule Proposed Issued Mar 26, 2001 5 pages Copy saved Nov 17, 2026

66 FR 16418 Airworthiness Directives; Raytheon Aircraft Company Beech Models 35, 35R, A35, and B35 Airplanes

This document proposes to supersede Airworthiness Directive (AD) 98-13-02, which currently requires operating limitations on Raytheon Aircraft Company (Raytheon) Beech Models 35, 35R, A35, and B35 airplanes. This proposed AD is the result of Raytheon developing inspection and modification procedures that, when accomplished on the affected airplanes, would eliminate the need for the operating limitations. This proposed AD would retain the operating limitations for the affected airplanes until the recently developed inspection and modification procedures are accomplished. The proposed AD would also require repetitive inspections of the fuselage structure. The actions specified by the proposed AD are intended to continue to prevent structural failure of the V-tail, which could result in loss of control of the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 2000-CE-44-AD] RIN 2120-AA64

Airworthiness Directives; Raytheon Aircraft Company Beech Models 35, 35R, A35, and B35 Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: This document proposes to supersede Airworthiness Directive (AD) 98-13-02, which currently requires operating limitations on Raytheon Aircraft Company (Raytheon) Beech Models 35, 35R, A35, and B35 airplanes. This proposed AD is the result of Raytheon developing inspection and modification procedures that, when accomplished on the affected airplanes, would eliminate the need for the operating limitations. This proposed AD would retain the operating limitations for the affected airplanes until the recently developed inspection and modification procedures are accomplished. The proposed AD would also require repetitive inspections of the fuselage structure. The actions specified by the proposed AD are intended to continue to prevent structural failure of the V-tail, which could result in loss of control of the airplane.

Dates

DATES: The Federal Aviation Administration (FAA) must receive any comments on this rule on or before May 25, 2001.

ADDRESSES: Submit comments in triplicate to FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2000-CE-44-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Comments may be inspected at this location between 8 a.m. and 4 p.m., Monday through Friday, holidays excepted.

Addresses

Service information that applies to the proposed AD may be obtained from the Raytheon Aircraft Company, PO Box 85, Wichita, Kansas 67201-0085; telephone: (800) 625-7043 or (316) 676-4556. This information also may be examined at the Rules Docket at the address above.

FOR FURTHER INFORMATION CONTACT: Mr. T.N. Baktha, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Mid-Continent Airport, Wichita, Kansas 67209; telephone: (316) 946-4155; facsimile: (316) 946-4407.

Supplementary Information

SUPPLEMENTARY INFORMATION:

Comments Invited

How do I comment on the proposed AD? The FAA invites comments on this proposed rule. You may submit whatever written data, views, or arguments you choose. You need to include the rule's docket number and submit your comments in triplicate to the address specified under the heading ADDRESSES. The FAA will consider all comments received on or before the closing date. We may amend the proposed rule in light of comments received. Factual information that supports your ideas and suggestions is extremely helpful in evaluating the effectiveness of the proposed AD action and determining whether we need to take additional rulemaking action.

Comments Invited

Are there any specific portions of the proposed AD I should pay attention to? The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of the proposed rule that might suggest a need to modify the rule. You may examine all comments we receive before and after the closing date of the rule in the Rules Docket. We will file a report in the Rules Docket that summarizes each FAA contact with the public that concerns the substantive parts of the proposed AD.

We are re-examining the writing style we currently use in regulatory documents, in response to the Presidential memorandum of June 1, 1998. That memorandum requires federal agencies to communicate more clearly with the public. We are interested in your comments on whether the style of this document is clear, and any other suggestions you might have to improve the clarity of FAA communications that affect you. You can get more information about the Presidential memorandum and the plain language initiative at http://www.plainlanguage.gov.

How can I be sure FAA receives my comment? If you want us to acknowledge the receipt of your comments, you must include a self-addressed, stamped postcard. On the postcard, write "Comments to Docket No. 2000-CE-44-AD." We will date stamp and mail the postcard back to you.

Discussion

Discussion

Has FAA taken any action on the Raytheon airplane ruddervator system to this point? AD 98-13-02, Amendment 39-10590 (63 FR 31916, June 11, 1998), currently requires the following on Raytheon Beech Models 35, A35, B35, and 35R airplanes:

--Fabricating a placard that restricts the never exceed speed (Vne) to no more than 144 miles per hour (MPH) or 125 knots (KTS) indicated airspeed (IAS), and installing this placard on the instrument panel within the pilot's clear view; --Marking a red line on the airspeed indicator glass at 144 MPH (125 KTS); --Marking a white slippage mark on the outside surface of the airspeed indicator between the glass and case; and --Inserting a copy of this AD into the Limitations Section of the POH/ AFM.

In addition, AD 94-20-04, Amendment 39-9032 (59 FR 49785, September 30, 1994), requires the following on certain Beech Models C35, D35, E35, F35, G35, H35, J35, K35, M35, N35, P35, S35, V35, V35A, and V35B airplanes, as well as the Beech Models 35, A35, B35, and 35R airplanes:

--Checking the ruddervator static balance and rebalancing the ruddervators when the balance is not in accordance with manufacturer's specifications or anytime the ruddervators are repaired or repainted; --Repetitively inspecting the fuselage bulkheads for damage, and replacing any damaged parts; --Installing stabilizer reinforcements for some airplane models, as applicable; --Fabricating and installing airspeed limitation placards; --Incorporating certain airspeed limitations into the airplane flight manual/pilot's operating handbook (POH/AFM); --Inspecting the empennage, aft fuselage, and ruddervator control system for damage, and replacing or repairing any damaged parts; and --Ensuring the accuracy of the airplane basic weight and balance information, and immediately correcting any discrepancies.

Accomplishment of these actions is required in accordance with the instructions to either Beech Kit No. 35-4016-3, 35-4016-5, 35-4016-7, or 35-4016-9, as applicable and as specified in Beech Service Bulletin No. 2188, dated May, 1987, and the applicable maintenance and shop manuals.

What has happened since AD 94-20-04 and AD 98-13-02 to initiate this action? AD 94-20-04 contains minor errors and FAA receives periodic calls from the public for clarification.

In addition, Raytheon has issued Recommended Service Bulletin No. SB 27-3358, Issued: February, 2000, which includes procedures for inspecting the aft fuselage, ruddervator, and related systems for acceptable condition and rebalancing the ruddervators to new specifications (upper limit reduced from 19.8 to 18 inch-pounds (tail heavy)). Accomplishing these inspections would eliminate the need for the operating limitations of AD 98-13-02. This service bulletin also includes the procedures necessary for continuing the repetitive inspections of the empennage, aft fuselage, and ruddervator control system (the inspections AD 94-20-04 currently require).

The FAA's Determination and Explanation of the Provisions of the Proposed AD

The FAA's Determination and Explanation of the Provisions of the Proposed AD

What has FAA decided? After examining the circumstances and reviewing all available information related to the incidents described above, we have determined that:

--The unsafe condition referenced in this document still exists or could develop on other Raytheon Beech Models 35, A35, B35, and 35R airplanes of the same type design; --The inspections specified in Raytheon Recommended Service Bulletin No. SB 27-3358, Issued: February, 2000, should be accomplished on Beech Models 35, 35R, A35, and B35 airplanes;

--The repetitive inspections currently required on these airplanes by AD 94-20-04 should be removed from AD 94-20-04 and included in this proposed AD. These repetitive inspections should be accomplished in accordance with Raytheon Recommended Service Bulletin No. SB 27-3358, Issued: February, 2000; and --AD action should be taken in order to continue to prevent structural failure of the V-tail, which could result in loss of control of the airplane.

What would the proposed AD require? This proposed AD would supersede AD 98-13-02 with a new AD. The proposed AD would require you to inspect the aft fuselage, ruddervator, and related systems for acceptable condition on Beech Models 35, 35R, A35, and B35 airplanes; adjust ruddervator balance to the new limits; and repair or replace damaged parts, as necessary. This proposed inspection requirement along with the new proposed limits for the ruddervator balance (set forth in Raytheon SB 27-3358, Section 3.A) would terminate the need for the operating limitations for those airplanes.

Cost Impact

Cost Impact

How many airplanes would the proposed AD impact? We estimate that the proposed AD affects 2,211 airplanes in the U.S. registry.

What would be the cost impact of the proposed AD on owners/ operators of the affected airplanes? We estimate the following costs to accomplish the proposed initial inspections:

Total cost on

Labor cost Parts cost Total cost per airplane U.S. operators

55 workhours at $60 per hour = $3,300. $500 per airplane … $3,800 … $8,401,800

The above figures are based only on the proposed initial inspections and do not take into account the cost of repetitive inspections or adjustments, repairs, or replacements that would be necessary based on the results of the inspections. We have no way of determining the number of repetitive inspections each owner/operator of the affected airplanes would incur or what adjustments, repairs, or replacements may be necessary based on the results of the inspections.

Regulatory Impact

Regulatory Impact

Would this proposed AD impact various entities? The regulations proposed herein would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this proposed rule would not have federalism implications under Executive Order 13132.

Would this proposed AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action has been placed in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the heading ADDRESSES.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 of the Federal Aviation Regulations as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by removing Airworthiness Directive (AD) 98-13-02, Amendment 39-10590 (63 FR 31916, June 11, 1998), and by adding a new AD to read as follows: Raytheon Aircraft Company (Beech Aircraft Corporation formerly held Type Certificate (TC) No. A-777): Docket No. 2000-CE-44-AD; Supersedes AD 98-13-02, Amendment 39-10590.

§ 39.13 [Amended]

(a) What airplanes are affected by this AD? This AD affects Beech Models 35, 35R, A35, and B35 airplanes, all serial numbers, that are certificated in any category.

(b) Who must comply with this AD? Anyone who wishes to operate any of the above airplanes must comply with this AD.

(c) What problem does this AD address? The actions specified by this AD are intended to prevent structural failure of the V-tail, which could result in loss of control of the airplane.

(d) What actions must I accomplish to address this problem on the affected airplanes? To address this problem, accomplish the following:

Actions Compliance Procedures

(1) Fabricate a placard that Within the next 10 Not Applicable.

restricts the never exceed hours time-in-

speed (Vne) to no more than service (TIS) after 144 miles per hour (MPH) or July 7, 1998 (the

speed (Vne) to no more than service (TIS) after 144 miles per hour (MPH) or July 7, 1998 (the

125 knots (KTS) indicated effective date of

airspeed (IAS), and install AD 98-13-02),

this placard on the unless already

instrument panel within the accomplished. pilot's clear view. The placard should utilize letters of at least 0.10-inch in height and contain the following words: "Never exceed speed, Vne, 144 MPH (125 KTS) IAS".

(2) Mark a red line on the Within the next 10 Not Applicable.

airspeed indicator glass at hours time-in-

airspeed indicator glass at hours time-in-

144 MPH (125 KTS) and mark service (TIS) after

a white slippage mark on July 7, 1998 (the

the outside surface of the effective date of

airspeed indicator between AD 98-13-02),

the glass and case. unless already

accomplished.

(3) Insert a copy of this AD Within the next 10 Not Applicable.

into the Limitations hours time-in-

Section of the airplane service (TIS) after

flight manual (AFM). July 7, 1998 (the

effective date of

AD 98-13-02),

unless already

accomplished.

(4) The owner/operator Within the next 10 Make an entry into

holding at least a private hours time-in- the aircraft

pilot certificate as service (TIS) after records showing

authorized by section 43.7 July 7, 1998 (the compliance with

of the Federal Aviation effective date of this AD in

Regulations (14 CFR 43.7) AD 98-13-02), accordance with

may fabricate and install unless already section 43.9 of the

the placard as required by accomplished. Federal Aviation

paragraph (d)(1) of this AD Regulations (14 CFR

and insert this AD into the 43.9).

Limitations Section of the AFM as required by paragraph (d)(3) of this AD.

(5) Visually inspect the Inspect within the Accomplish the

empennage, aft fuselage, next 100 hours TIS inspection and

and ruddervator control after the last repairs or

system for damage. Repair inspection required replacements in

or replace any damaged by AD 94-20-04 or accordance with

parts and set the elevator within the next 25 paragraphs (5)(a)

controls, rudder and tab hours TIS after the through (5)(f) of

system controls, cable effective date of the ACCOMPLISHMENT

tensions, and rigging. this AD, whichever INSTRUCTIONS

occurs later, and section of Raytheon

thereafter at Service Bulletin

intervals not to No. SB 27-3358,

exceed 100 hours Issued: February,

TIS. Accomplish any 2000.

repairs,

replacements, and

adjustments prior

to further flight

after the

applicable

inspection.

(6) Verify the accuracy of Accomplish the Use the procedures

the airplane basic weight airplane basic contained in the

and balance information and weight and balance Appendix to this

correct any discrepancies. accuracy AD.

verification within

the next 100 hours

TIS after the

effective date of

this AD, unless

already

accomplished as

previously required

by AD 94-20-04.

Correct any

discrepancies prior

to further flight

after the

verification.

(7) Inspect the aft Accomplish the Accomplish the

fuselage, ruddervator, and inspections within inspection and

related systems for the next 2 years repairs or

acceptable condition. after the effective replacements in

date of this AD, accordance with all

unless already paragraphs in the

accomplished. ACCOMPLISHMENT

Accomplish any INSTRUCTIONS

repair or section of Raytheon

replacement prior Service Bulletin

to further flight No. SB 27-3358,

after the Issued: February,

inspection. 2000. Accomplish

Accomplish any the rebalancing in

ruddervator accordance with

rebalancing prior Section 3A(8) of

to further flight the service

after the bulletin and use

inspection and when the procedure in

the ruddervators Section 3 of Beech

are repaired or Shop Manual 35-

repainted (even if 590096B19 (or

stripes are added subsequent

or paint is touched revision).

up).

(i) Repair or replace any parts found unacceptable as specified in the service bulletin; (ii) Rebalance the ruddervators to the new specifications that reduce the upper limit from 19.8 to 18 inch-pounds (tail heavy); and (iii) Discontinue the placard and operating limitations required by paragraphs (d)(1) through (d)(4) of this AD.

(e) Can I comply with this AD in any other way?

(1) You may use an alternative method of compliance or adjust the compliance time if:

(i) Your alternative method of compliance provides an equivalent level of safety; and

(ii) The Manager, Wichita Aircraft Certification Office (ACO), approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Wichita ACO.

(2) Alternative methods of compliance approved in accordance with AD 98-13-02, which is superseded by this AD, are approved as alternative methods of compliance with this AD.

Note: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.

(f) Where can I get information about any already-approved alternative methods of compliance? Contact Mr. T.N. Baktha, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Mid-Continent Airport, Wichita, Kansas 67209; telephone: (316) 946-4155; facsimile: (316) 946-4407.

(g) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.

(h) How do I get copies of the documents referenced in this AD? You may obtain copies of the documents referenced in this AD from the Raytheon Aircraft Company, PO Box 85, Wichita, Kansas 67201-0085. You may examine these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

(i) Does this AD action affect any existing AD actions? This amendment supersedes AD 98-13-02, Amendment 39-10590.

Appendix to Docket No. 2000-CE-44-AD

Appendix to Docket No. 2000-CE-44-AD

Weight and Balance Accuracy Method No. 1:

1. Review existing weight and balance documentation to assure completeness and accuracy of the documentation from the most recent FAA-approved weighing or from factory delivery to date of compliance with this AD.

2. Compare the actual configuration of the airplane to the configuration described in the weight and balance documentation; and

3. If equipment additions or deletions are not reflected in the documentation or if modification affecting the location of the center of gravity (e.g., paint or structural repairs) are not documented, determine the accuracy of the airplane weight and balance data in accordance with Method No. 2.

Weight and Balance Information Accuracy Method No. 2:

1. Determine the basic empty weight and center of gravity (CG) of the empty airplane using the Weighing Instructions in the Weight and Balance section of the airplane flight manual/pilot's operating handbook (AFM/POH).

2. Record the results in the airplane records, and use these new values as the basis for computing the weight and CG information as specified in the Weight and Balances section of the AFM/POH.

Issued in Kansas City, Missouri, on March 19, 2001. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.