Radar Vectors
Proposed Rule Proposed Issued Sep 26, 2001 5 pages Copy saved Nov 17, 2026

66 FR 49148 Airworthiness Directives; EXTRA Flugzeugbau GmbH Models EA-300, EA-300L, and EA-300S Airplanes

This document proposes to adopt a new airworthiness directive (AD) that would apply to certain EXTRA Flugzeugbau GmbH (EXTRA) Models EA-300, EA-300L, and EA-300S airplanes. The proposed AD would require (for all affected airplanes) an inspection of the upper longeron at the horizontal stabilizer attachment for cracks using a fluorescent dye check penetrant method, repair of any cracks found, and modification of the horizontal stabilizer. The proposed AD would require a limit on operation to the Normal category until accomplishment of the initial inspection and modification on airplanes with less than 200 hours time-in-service (TIS). The proposed AD is the result of reports of fatigue cracks at the horizontal stabilizer attachment on the affected airplanes. The actions specified by the proposed AD are intended to detect and correct cracks in the horizontal stabilizer attachment, which could result in structural failure of the aft fuselage with consequent loss of control of the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 99-CE-85-AD] RIN 2120-AA64

Airworthiness Directives; EXTRA Flugzeugbau GmbH Models EA-300, EA-300L, and EA-300S Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: This document proposes to adopt a new airworthiness directive (AD) that would apply to certain EXTRA Flugzeugbau GmbH (EXTRA) Models EA-300, EA-300L, and EA-300S airplanes. The proposed AD would require (for all affected airplanes) an inspection of the upper longeron at the horizontal stabilizer attachment for cracks using a fluorescent dye check penetrant method, repair of any cracks found, and modification of the horizontal stabilizer. The proposed AD would require a limit on operation to the Normal category until accomplishment of the initial inspection and modification on airplanes with less than 200 hours time-in-service (TIS). The proposed AD is the result of reports of fatigue cracks at the horizontal stabilizer attachment on the affected airplanes. The actions specified by the proposed AD are intended to detect and correct cracks in the horizontal stabilizer attachment, which could result in structural failure of the aft fuselage with consequent loss of control of the airplane.

Dates

DATES: The Federal Aviation Administration (FAA) must receive any comments on this proposed rule on or before October 31, 2001.

ADDRESSES: Submit comments to FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 99-CE-85-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. You may view any comments at this location between 8 a.m. and 4 p.m., Monday through Friday, except Federal holidays.

Addresses

You may get service information that applies to this proposed AD from EXTRA Flugzeugbau GmbH, Flugplatz Dinslaken, D-46569 Hunxe, Federal Republic of Germany; telephone: (0 28 58) 91 37-00; facsimile: (0 28 58) 91 37-30. You may also view this information at the Rules Docket at the address above.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; facsimile: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Comments Invited

How Do I Comment on This Proposed AD?

How Do I Comment on This Proposed AD?

The FAA invites comments on this proposed rule. You may submit whatever written data, views, or arguments you choose. You need to include the rule's docket number and submit your comments to the address specified under the caption ADDRESSES. We will consider all comments received on or before the closing date. We may amend this proposed rule in light of comments received. Factual information that supports your ideas and suggestions is extremely helpful in evaluating the effectiveness of this proposed AD action and determining whether we need to take additional rulemaking action.

Are There Any Specific Portions of This Proposed AD I Should Pay Attention to?

Are There Any Specific Portions of This Proposed AD I Should Pay Attention to?

FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of this proposed rule that might suggest a need to modify the rule. You may view all comments we receive before and after the closing date of the rule in the Rules Docket. We will file a report in the Rules Docket that summarizes each contact we have with the public that concerns the substantive parts of this proposed AD.

How Can I Be Sure FAA Receives My Comment?

How Can I Be Sure FAA Receives My Comment?

If you want us to acknowledge the receipt of your comments, you must include a self-addressed, stamped postcard. On the postcard, write "Comments to Docket No. 99-CE-85-AD." We will date stamp and mail the postcard back to you.

Discussion

What Events Have Caused This Proposed AD?

What Events Have Caused This Proposed AD?

On October 17, 1997, FAA issued a Special Airworthiness Information Bulletin (SAIB) to recommend an inspection of the horizontal stabilizer attachment on EXTRA Models EA-300, EA-300L, and EA-300S airplanes. The SAIB recommended compliance with EXTRA Service Bulletin SB-300-2-95.

The Luftfahrt-Bundesamt (LBA), which is the airworthiness authority for Germany, did not consider the actions of the service bulletin mandatory and consequently did not issue an AD against airplanes on the German register. The FAA also did not issue an AD at this time because the service history did not warrant such action.

Since that time, FAA has received information that indicates fatigue cracks at the horizontal stabilizer attachment are occurring on the above-referenced airplanes. These airplanes are utilized in aerobatic maneuvers and the stress in the area of the horizontal stabilizer can lead to cracks in this area, as well as in the upper longerons and diagonal braces.

What Are the Consequences if the Condition Is Not Corrected?

What Are the Consequences if the Condition Is Not Corrected?

This condition, if not corrected, could lead to structural failure of the aft fuselage with consequent loss of control of the airplane.

Is There Service Information That Applies to This Subject?

As indicated above, EXTRA Service Bulletin SB-300-2-95 pertains to this subject. EXTRA has since revised Service Bulletin No. 300-2-95 (pages 2-6 at Issue: C, dated July 15, 1998; and pages 1 and 7 through 11 at Issue: D, dated January 30, 2001).

What Action Did LBA Take?

What Action Did LBA Take?

As of the issue date of this NPRM, LBA has not taken AD action on this subject.

The FAA's Determination and an Explanation of the Provisions of the Proposed AD

What Has FAA Decided?

After examining the circumstances and reviewing all available information related to the incidents described above, including the referenced service information, we have determined that:

What Has FAA Decided?

--The unsafe condition referenced in this document exists or could develop on other EXTRA Models EA-300, EA-300L, and EA-300S airplanes of the same type design registered in the United States; and --AD action should be taken in order to detect and correct cracks in the horizontal stabilizer attachment, which could result in structural failure of the aft fuselage with consequent loss of control of the airplane.

What Would the Proposed AD Require?

What Would the Proposed AD Require?

This proposed AD would require:

--For all affected airplanes: an inspection of the upper longeron at the horizontal stabilizer attachment for cracks using a fluorescent dye check penetrant method, repair of any cracks found, and modification of the horizontal stabilizer; and --On airplanes with less than 200 hours time-in-service (TIS) as of the effective date of the proposed AD: a limit on operation to the Normal category until accomplishment of the initial inspection and modification.

Accomplishment of the actions specified in the proposed AD would be in accordance with the instructions included in the proposed AD and as specified in the applicable service manual.

Cost Impact

Cost Impact

How Many Airplanes Would the Proposed AD Impact?

We estimate that the proposed AD affects 55 airplanes in the U.S. registry.

What Would Be the Cost Impact of the Proposed AD on Owners/Operators of the Affected Airplanes?

We estimate the following costs to accomplish the proposed inspection:

What Would Be the Cost Impact of the Proposed AD on Owners/Operators of the Affected Airplanes?

Total cost on U.S.

Labor cost Parts cost Total cost per airplane operators

24 workhours x $60 per hour = $1,440 Not Applicable … $1,440 per airplane … $1,440 x 55 airplanes

= $79,200.

We estimate the following costs to accomplish the proposed modification: …

20 workhours x $60 per hour = $1,200 Provided at no cost … $1,200 per airplane … $1,200 x 55 airplanes

= $66,000.

We estimate the following costs to accomplish any necessary repair or replacement that would be required based on the results of the proposed inspection. We have no way of determining the number of airplanes that may need such repair or replacement:.

Labor cost Parts cost Total cost per airplane

40 workhours x $60 per hour = $2,400. Parts provided at no cost. $2,400 per airplane.

Regulatory Impact

Regulatory Impact

Would This Proposed AD Impact Various Entities?

The regulations proposed herein would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this proposed rule would not have federalism implications under Executive Order 13132.

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

For the reasons discussed above, I certify that this proposed action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action has been placed in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding a new airworthiness directive (AD) to read as follows:

EXTRA Flugzeugbau GMBH: Docket No. 99-CE-85-AD.

§ 39.13 [Amended]

(a) What airplanes are affected by this AD? This AD applies to the following airplane models and serial numbers that are certificated in any category:

Model Serial Nos.

EA-300 … 1 through 62

EA-300L … 1 through 5

EA-300S … 1 through 29

(b) Who must comply with this AD? Anyone who wishes to operate any of the above airplanes must comply with this AD.

(c) What problem does this AD address? The actions specified by this AD are intended to detect and correct cracks in the horizontal stabilizer attachment, which could result in structural failure of the aft fuselage with consequent loss of control of the airplane.

(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:

Actions Compliance Procedures

(1) For all affected Upon accumulating In accordance with

airplanes, inspect, using a 250 hours time-in- Part I of Extra

fluorescent dye penetrant service (TIS) or Service Bulletin

method, the upper longeron within the next 50 No. 300-2-95 (pages

at the horizontal hours TIS after the 2-6 at Issue: C,

stabilizer attachment for effective date of dated July 15,

cracks in the areas this AD, whichever 1998; and pages 1

depicted in Figure 1 of occurs later. and 7 through 11 at

this AD. Issue: D, dated

January 30, 2001).

No further action

is required by this

paragraph if the

modification is

already

accomplished in

accordance with

Part II of Extra

Service Bulletin

No. 300-2-95 (all

pages at Issue: C,

dated July 15,

1998).

(2) For all affected air Prior to further In accordance with

planes, if no crack(s) flight after the Part II of Extra

is(are) found during the inspection required Service Bulletin

inspection required by this by paragraph (d)(1) No. 300-2-95 (pages

inspection required by this by paragraph (d)(1) No. 300-2-95 (pages

AD, modify the upper of this AD. 2-6 at Issue: C,

longeron at the horizontal dated July 15,

stabilizer attachment. 1998; and pages 1

and 7 through 11 at

Issue: D, dated

January 30, 2001).

No further action

is required by this

paragraph if

already

accomplished in

accordance with

Part II of Extra

Service Bulletin

No. 300-2-95 (all

pages at Issue: C,

dated July 15,

1998).

(3) For all affected Prior to further In accordance with

airplanes, if any crack is flight after the Part II of Extra

found during the inspection inspection where Service Bulletin

required by this AD and the any crack is found No. 300-2-95,

crack(s) is(are) in Area A in Area A or Area B Issue: D, dated

or Area B as depicted in as depicted in January 30, 2001.

Figure 1 of this AD, Figure 1 of this Ad. No further action

accomplish the following: is required by this

(i) Repair and modify the paragraph if

upper longeron at the already

horizontal stabilizer accomplished in

attachment; and. accordance with

(ii) Weld the cracks tight Part II of Extra

during repair.. Service Bulletin

No. 300-2-95 (all

pages at Issue: C,

dated July 15,

1998).

(4) For all affected Prior to further In accordance with a

airplanes, if any crack is flight after the repair scheme

found during the inspection inspection where obtained from EXTRA

and the crack(s) is(are) in any crack is found. Flugzeugbau GmbH,

Area C as depicted in Flugplatz

Figure 1 of this AD, Dinslaken, D-46569

accomplish the following: Hunxe, Federal

(i) Obtain a repair scheme Republic of

from the manufacturer;. Germany; telephone:

(ii) Incorporate this repair (0 28 58) 91 37-00;

scheme; and. facsimile: (0 28

(iii) Accomplish any follow- 58) 91 37-30.

up actions as directed by Obtain this repair

the FAA.. scheme through FAA

at the address

specified in

paragraph (f) of

this and AD.

(5) For airplanes with less Within the next 50 Not applicable.

than 200 hours TIS as of hours TIS after the

the effective date of this effective date of

AD, limit operation to the this AD until the

Normal category by inspection and the

accomplishing the modification

following: required by this AD

(i) Fabricate two placards are accomplished.

using letters of at least \1/10\-inch in height consisting of the following words: "OPERATIONS LIMITED TO NORMAL CATEGORY";. (ii) Install these placards on the airplane instrument panels (one on the front panel and one on the rear panel) next to the airspeed indicators within the pilot's clear view; and. (iii) Insert a copy of this AD into the Limitations Section of the Airplane Flight Manual (AFM)..

(6) The Owner/operator Within the next 50 Make an entry into

holding at least a private hours TIS after the the aircraft

pilot certificate as effective date of records showing

authorized by section 43.7 this AD until the compliance with

of the Federal Aviation first inspection this AD in

Regulations (14 CFR 43.7) and the accordance with

may fabricate and install modification section 43.9 of the

the placard as required by required by this AD Federal Aviation

paragraphs (d)(5)(i) and are accomplished. Regulations (14 CFR

(d)(5)(ii) of this AD and and the 43.9).

insert this AD into the Limitations Section of the AFM as required by paragraph (d)(5)(iii) of this AD.

(7) For all affected Model Within the next 200 In accordance with

EA-300S airplanes, modify hours TIS after the Part III of Extra

the fuselage frame effective date of Service Bulletin

underneath the stabilizer this AD. No. 300-2-95 (pages

attachment. 2-6 at Issue: C,

dated July 15,

1998; and pages 1

and 7 through 11 at

Issue: D, dated

January 30, 2001).

(8) For all affected Upon accumulating Inspect in

airplanes with less than 250 hours TIS or accordance with

200 hours TIS as of the within the next 50 Figure 1 of this AD

effective date of this AD, hours TIS after the and Part I of Extra

the inspection, effective date of Service Bulletin

modification, and repair, this AD, whichever No. 300-2-95 (pages

as necessary, (as specified occurs later. 2-6 at Issue: C,

in paragraphs (d)(1) dated July 15,

through (d0(4) of this AD) 1998; and pages 1

may be accomplished instead and 7 through 11 at

of the operational Issue: D, dated

limitations of paragraph January 30, 2001).

(d)(5) of this AD. Modify in

accordance with

Part II of the

service bulletin.

Repair in

accordance with the

service bulletin or

a repair scheme

obtained from the

manufacturer, as

applicable.

(e) Can I comply with this AD in any other way? You may use an alternative method of compliance or adjust the compliance time if:

(1) Your alternative method of compliance provides an equivalent level of safety; and

(2) The Manager, Small Airplane Directorate, approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Small Airplane Directorate.

Note 1: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.

(f) Where can I get information about any already-approved alternative methods of compliance? Contact Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; facsimile: (816) 329-4090.

(g) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.

(h) How do I get copies of the documents referenced in this AD? Direct questions or technical information related to Extra Service Bulletin No. 300-2-95 (pages 2-6 at Issue: C, dated July 15, 1998; and pages 1 and 7 through 11 at Issue: D, dated January 30, 2001) to EXTRA Flugzeugbau GmbH, Flugplatz Dinslaken, D-46569 Hunxe, Federal Republic of Germany; telephone: (0 28 58) 91 37-00; facsimile: (0 28 58) 91 37-30. You may view this service information at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

Issued in Kansas City, Missouri, on September 18, 2001. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.