65 FR 1350 Airworthiness Directives; Airbus Model A319, A320, A321, A330, and A340 Series Airplanes
This document proposes the adoption of a new airworthiness directive (AD) that is applicable to certain Airbus Model A319, A320, A321, A330, and A340 series airplanes. This proposal would require revising the Airplane Flight Manual to provide the flight crew with certain instructions associated with the Global Positioning System (GPS). This proposal also would require modification of the Global Positioning System Signal Unit (GPSSU) of the satellite navigational system. This proposal is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by the proposed AD are intended to prevent position and altitude errors due to bad oscillator warm-up characteristics of the GPSSU, which could result in navigational errors that may exceed 0.5 nautical mile.
This document is proposed. It may have been replaced. Check the official source before relying on it.
[Docket No. 99-NM-349-AD] RIN 2120-AA64
Airworthiness Directives; Airbus Model A319, A320, A321, A330, and A340 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: This document proposes the adoption of a new airworthiness directive (AD) that is applicable to certain Airbus Model A319, A320, A321, A330, and A340 series airplanes. This proposal would require revising the Airplane Flight Manual to provide the flight crew with certain instructions associated with the Global Positioning System (GPS). This proposal also would require modification of the Global Positioning System Signal Unit (GPSSU) of the satellite navigational system. This proposal is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by the proposed AD are intended to prevent position and altitude errors due to bad oscillator warm-up characteristics of the GPSSU, which could result in navigational errors that may exceed 0.5 nautical mile.
Dates
DATES: Comments must be received by February 9, 2000.
ADDRESSES: Submit comments in triplicate to the Federal Aviation Administration (FAA), Transport Airplane Directorate, ANM-114, Attention: Rules Docket No. 99-NM-349-AD, 1601 Lind Avenue, SW., Renton, Washington 98055-4056. Comments may be inspected at this location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except Federal holidays.
Addresses
The service information referenced in the proposed rule may be obtained from Airbus Industrie, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France. This information may be examined at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington.
FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149.
Supplementary Information
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the proposed rule by submitting such written data, views, or arguments as they may desire. Communications shall identify the Rules Docket number and be submitted in triplicate to the address specified above. All communications received on or before the closing date for comments, specified above, will be considered before taking action on the proposed rule. The proposals contained in this notice may be changed in light of the comments received.
Comments Invited
Comments are specifically invited on the overall regulatory, economic, environmental, and energy aspects of the proposed rule. All comments submitted will be available, both before and after the closing date for comments, in the Rules Docket for examination by interested persons. A report summarizing each FAA-public contact concerned with the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments submitted in response to this notice must submit a self-addressed, stamped postcard on which the following statement is made: "Comments to Docket Number 99-NM-349-AD." The postcard will be date stamped and returned to the commenter.
Availability of NPRMs
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules Docket No. 99-NM-349-AD, 1601 Lind Avenue, SW., Renton, Washington 98055-4056.
Discussion
The Direction Generale de l'Aviation Civile (DGAC), which is the airworthiness authority for France, notified the FAA that an unsafe condition may exist on certain Airbus Model A319, A320, A321, A330, and A340 series airplanes. The DGAC advises that the navigational satellite signals of the Global Positioning System (GPS) (located in the cockpit) may be incorrectly measured by the Global Positioning System Signal Unit (GPSSU) (located in the fuselage) due to bad oscillator warm-up characteristics of the GPSSU. In the event that only one GPS in the cockpit is operative, the erroneous GPS position computation may not be detected. This condition, if not corrected, could result in navigational errors that may exceed 0.5 nautical mile.
Explanation of Relevant Service Information
Explanation of Relevant Service Information
The manufacturer has issued Airbus Service Bulletins A320-34-1191, dated July 12, 1999, and A320-34-1196, dated July 15, 1999 (for Model A319, A320 and A321 series airplanes); A330-34-3082, Revision 01, dated September 28, 1999, and A330-34-3086, Revision 01, dated September 28, 1999 (for Model A330 series airplanes); and A340-34-4089, Revision 01, dated September 28, 1999, and A340-34-4092, Revision 01, dated September 28, 1999 (for Model A340 series airplanes). These service bulletins describe procedures for modification of the GPSSU of the satellite navigational system. The modification involves modifying the hardware and software in order to minimize synchronization conditions, accommodate an automatic reset and the GPS week number rollover, and provide failure recording capabilities in the non-volatile memory.
In addition, these service bulletins identify related service bulletins that must be accomplished prior to or concurrent with the applicable service bulletin. These additional service bulletins are as follows:
• A320-34-1119
• A330-34-3015
• A340-34-4022
• A340-34-4078
The Airbus service bulletins described previously also reference LITTON Service Bulletin 2001-34-13, dated July 8, 1999, and 2001-34-14, dated July 5, 1999, as additional sources of service information for modification of the GPSSU the satellite navigational system.
Accomplishment of the actions specified in the Airbus service bulletins is intended to adequately address the identified unsafe condition. The DGAC classified these Airbus service bulletins as mandatory and issued French airworthiness directives 1999-361-138(B), dated September 8, 1999 (for Models A319, A320, and A321 series airplanes); 1999-354-101(B), dated September 8, 1999 (for Model A330 series airplanes); and 1999-355-123(B), dated September 8, 1999 (for Model A340 series airplanes); in order to assure the continued airworthiness of these airplanes in France.
The French airworthiness directives also require revising the applicable Airplane Flight Manual (AFM) to provide the flight crew with certain instructions regarding deselecting the GPS navigational system.
FAA's Conclusions
FAA's Conclusions
These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DGAC has kept the FAA informed of the situation described above. The FAA has examined the findings of the DGAC, reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation in the United States.
Explanation of Requirements of Proposed Rule
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to exist or develop on other airplanes of the same type design registered in the United States, the proposed AD would require accomplishment of the actions specified in the Airbus service bulletins described previously. The proposed AD also requires revising the FAA-approved AFM to provide the flight crew with certain instructions associated with the GPS.
Cost Impact
Cost Impact
The FAA estimates that 1 airplane of U.S. registry would be affected by this proposed AD.
It would take approximately 1 work hour per airplane to accomplish the proposed Airplane Flight Manual (AFM) revision, at an average labor rate of $60 per work hour. Based on these figures, the cost impact of the AFM revision proposed by this AD on U.S. operators is estimated to be $60, or $60 per airplane.
It would take approximately 1 work hour per airplane to accomplish the proposed modification, at an average labor rate of $60 per work hour. Based on these figures, the cost impact of the modification proposed by this AD on U.S. operators is estimated to be $60, or $60 per airplane.
It would take between 3 to 14 work hours per airplane to accomplish the proposed additional modifications required to be accomplished prior to or concurrent with the proposed modification, at an average labor rate of $60 per work. Required parts would be provided by the vendor or manufacturer at no cost to the operators. Based on these figures, the cost impact of the additional modifications proposed by this AD on U.S. operators is estimated to be between $180 to $840 per airplane.
The cost impact figures discussed above are based on assumptions that no operator has yet accomplished any of the proposed requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted.
Regulatory Impact
Regulatory Impact
The regulations proposed herein would not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this proposal would not have sufficient federalism implications to warrant the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed regulation (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action is contained in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. Section 39.13 is amended by adding the following new airworthiness directive:
Airbus Industrie: Docket 99-NM-349-AD.
§ 39.13 [Amended]
Applicability: Model A319, A320, A321, A330, and A340 series airplanes, certificated in any category, as follows:
• Model A319, A320, and A321 series airplanes on which Airbus Modification 28578 (Airbus Service Bulletin A320-34-1191, dated July 12, 1999), or Airbus Modification 28579 (Airbus Service Bulletin A320-34-1196, dated July 15) has not been accomplished; equipped with a LITTON Global Positioning Satellite Signal Unit (GPSSU) having Part Number (P/N) 465205-0302-0303 installed in accordance with Airbus Service Bulletin A320-34-1119 (Airbus Modification 23885).
• Model A330 series airplanes on which Airbus Modification 46961 (Airbus Service Bulletin A330-34-3082, Revision 01, dated September 28, 1999), or Airbus Modification 47327 (Airbus Service Bulletin A330-34-3086, Revision 01, dated September 28, 1999) has not been accomplished; equipped with a LITTON GPSSU having P/N 465205-0302-0302 or 465205-0302-0303.
• Model A340 series airplanes on which Airbus Modification 46961 (Airbus Service Bulletin A340-34-4089, Revision 01, dated September 28, 1999), or Airbus Modification 47327 (Airbus Service Bulletin A340-34-4092, Revision 01, dated September 28, 1999) has not been accomplished; equipped with a LITTON GPSSU having P/N 465205-0302-0302 or 465205-0302-0303.
Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been otherwise modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (d) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.
Compliance: Required as indicated, unless accomplished previously.
To prevent position and altitude errors due to bad oscillator warm-up characteristics of the GPSSU, which could result in navigational errors that may exceed 0.5 nautical mile, accomplish the following:
AFM Revision
AFM Revision
(a) Within 10 days after the effective date of this AD, revise the Limitations Section of the FAA-approved Airplane Flight Manual (AFM) to include the following procedures. This may be accomplished by inserting a copy of this AD in the AFM.
"Operation:
--GPS Stand-alone and GPS overlay non-precision approaches are not allowed.
--The GPS must be deselected before non-precision approach.
--The GPS must be deselected for the remainder of the flight if `NAV FM/GPS POS DISAGREE' ECAM warning is triggered (in all phases of flight)
Dispatch:
--If one GPS is inoperative, GPS must be deselected."
Note 2: The AFM revision may be accomplished by inserting a copy of Airbus Temporary Revision (TR) 2.05.00/40 (for Model A319, A320, and A321 series airplanes); TR 2.05.00/38 (for Model A330 series airplanes); or TR2.05.00/47 (for A340 series airplanes); into the applicable AFM.
Modification
Modification
(b) Within 2 months after the effective date of this AD, modify the GPSSU of the satellite navigational system, in accordance with (b)(1), (b)(2), or (b)(3) of this AD, as applicable. After accomplishment of the modification, the AFM revision required by paragraph (a) of this AD may be removed from the AFM.
(1) For Model A319, A320, and A321 series airplanes: Modify the GPSSU in accordance with either Airbus Service Bulletin A320-34-1191, dated July 12, 1999, or Airbus Service Bulletin A320-34-1196, dated July 15, 1999.
(i) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A320-34-1191, prior to or concurrent with accomplishment of the modification, accomplish either Airbus Service Bulletin A320-34-1119, Revision 02, dated April 30, 1997, or A320-34-1196, dated July 15, 1999.
(ii) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A320-34-1196, prior to or concurrent with accomplishment of the modification, accomplish Airbus Service Bulletin A320-34-1119, Revision 02, dated April 30, 1997.
(2) For Model A330 series airplanes: Modify the GPSSU in accordance with either Airbus Service Bulletin A330-34-3082, Revision 01, dated September 28, 1999, or Airbus Service Bulletin A330-34-3086, Revision 01, dated September 28, 1999.
(i) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A330-34-3082, Revision 01, prior to or concurrent with accomplishment of the modification, accomplish either Airbus Service Bulletin A330-34-3015, dated April 3, 1995, or Airbus Service Bulletin A330-34-3086, Revision 01, dated September 28, 1999.
(ii) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A330-34-3086, Revision 01, prior to or concurrent with accomplishment of the modification, accomplish Airbus Service Bulletin A330-34-3015, dated April 3, 1995.
(3) For Model A340 series airplanes: Modify the GPSSU in accordance with either Airbus Service Bulletin A30-34-4089, Revision 01, dated September 28, 1999, or Airbus Service Bulletin A330-34-4092, Revision 01, dated September 28, 1999.
(i) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A330-34-4089, Revision 01, prior to or concurrent with accomplishment of the modification, accomplish either Airbus Service Bulletin A330-34-4022, dated April 3, 1995, or Airbus Service Bulletin A330-34-4092, Revision 01, dated September 28, 1999.
(ii) If modification of the GPSSU is accomplished in accordance with Airbus Service Bulletin A330-34-4092, Revision 01, prior to or concurrent with accomplishment of the modification, accomplish either Airbus Service Bulletin A330-34-4022, dated April 3, 1995, or Airbus Service Bulletin A340-34-4078, Revision 01, dated November 26, 1999, including Appendix 01, dated November 26, 1999.
Note 3: The Airbus service bulletins reference LITTON Service Bulletin 2001-34-13, dated July 8, 1999, and LITTON Service Bulletin 2001-34-14, dated July 5, 1999, as additional sources of service information for modifying the GPSSU.
(c) As of the effective date of this AD, no person shall install on any airplane a GPSSU having P/N 465205-0302-0302 or 465205-0302-0303.
Alternative Methods of Compliance
Alternative Methods of Compliance
(d) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance and Operations Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116.
Note 4: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116.
Special Flight Permits
Special Flight Permits
(e) Special flight permits may be issued in accordance with §§ 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.
Note 5: The subject of this AD is addressed in French airworthiness directives 1999-361-138(B), dated September 8, 1999; 1999-354-101(B), dated September 8, 1999; and 1999-355-123(B), dated September 8, 1999; in order to assure the continued airworthiness of these airplanes in France.
Issued in Renton, Washington, on January 4, 2000. Donald L. Riggin, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.