Radar Vectors
Final Rule Current Issued Dec 27, 2000 5 pages Copy saved Nov 17, 2026

65 FR 81733 Corrections to Flight Data Recorder Specifications

This action corrects errors introduced into the flight data recorder specifications in two final rules. The FAA intended to add certain information by footnote in the appendices that contain the flight recorder specification charts, but inadvertently caused material to be deleted. This correction reinstates that material.

Official source ↗ Official PDF ↗

14 CFR Parts 121 and 125

[Docket Nos. 121-271, 121-278, 125-32 & 125-34] RIN 2120-AG-88

Corrections to Flight Data Recorder Specifications

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; correction.

SUMMARY: This action corrects errors introduced into the flight data recorder specifications in two final rules. The FAA intended to add certain information by footnote in the appendices that contain the flight recorder specification charts, but inadvertently caused material to be deleted. This correction reinstates that material.

Dates

DATES: Effective December 27, 2000.

FOR FURTHER INFORMATION CONTACT: Karen Petronis, Senior Attorney for Regulations, AGC-200, Office of the Chief Counsel, Federal Aviation Administration, 800 Independence Avenue, SW., Washington, DC 20591; telephone 202-267-3073.

SUPPLEMENTARY INFORMATION: The FAA published final rule amending the flight data recorder specifications for certain Airbus airplanes in the Federal Register on August 24, 1999 [64 FR 46117]. The intent of that final rule was to establish different criteria for certain flight data recorder parameters that are recorded by Airbus airplanes. The changes were introduced as footnotes. The footnote numbers were to appear with the name of the parameter in the "Parameters" columns of 14 CFR part 121 appendix M and part 125 appendix E.

Supplementary Information

Instead of inserting the footnotes numbers in the column and adding the noted information at the bottom of the chart, the amendatory language that was used resulted in information being deleted from the five remaining columns of the chart for each of the parameters affected by the rule. A similar attempted amendment in August 2000 [65 FR 51745, August 24, 2000] caused the same result.

Accordingly, the FAA is republishing the affected parameter specifications to reinstate them in the appendix M chart. The identical corrections are being made to Part 125 Appendix E, which contains the identical information. The FAA never intended to change any of the information that was effective at the time of the August 1999 final rule, and no intent may be implied by the absence of this information from the printed 2000 CFR. The FAA has no information to suggest that any operator subject to the affected regulations has taken any action based on the unintended deletion of the information. The required specifications are well established and not easily changed in operational flight data recorder system equipment.

Since no rule change was ever intended, there is no economic impact that is attributable to this correction.

Any operator that finds itself adversely affected by reliance on any omission from the 2000 CFR is advised to contract the FAA immediately for resolution of any problems.

Accordingly, the Federal Aviation Administration amends Title 14 of the Code of Federal Regulations parts 121 and 125 as follows:

Part 121 [Corrected]

Appendix M [Corrected]

1. Correct Appendix M to part 121, by revising item numbers, 1, 7, 9, 12b, 13b, 14a, 15, 16, 17, 19, 20, 21, 23, 24, 37, 42 and 57 to read as follows (Note: The footnote text remains unchanged):

Appendix M [Corrected]

Accuracy (sensor second per sampling

Parameters Range input) interval Resolution Remarks

1. Time or Relative Times 24 Hrs, 0 to 4095 … +/-0.125% Per Hour.... 4 … 1 sec … UTC time preferred

Counts.\1\. when available.

Count increments

each 4 second of

system operation.

7. Roll attitude \2\ … +/-180 deg … +/-2 deg … 1 or 0.5 for 0.5 … A sampling rate of

airplanes operated 0.5 is recommended.

under Sec.

121.344(f).

9. Thrust/Power on Each Engine-- Full Range Forward.... +/-2% … 1 (per engine) … 0.2% of full range... Sufficient parameters

primary flight crew reference.\14\. (e.g. EPR, NI or

Torque, NP) as

appropriate to the

particular engine be

recorded to

determine power in

forward and reverse

thrust, including

potential over-speed

condition.

12b. Pitch Control(s) position (fly- Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range...

by-wire systems).\3\. Higher Accuracy airplanes operated

Uniquely Required.. under Sec.

121.344(f)..

13b. Lateral Control position(s) Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range...

(fly-by-wire).\4\. Higher Accuracy airplanes operated

Uniquely Required. under Sec.

121.344(f).

14a. Yaw Control position(s) (non- Full Range … +/-2 deg. Unless 0.5 … 0.2% of full range... For airplanes that

fly-by-wire).\5\. Higher Accuracy have a flight

Uniquely Required. control break away

capability that

allows either pilot

to operate the

controls

independently,

record both control

inputs. The control

inputs may be

sampled alternately

once per second to

produce the sampling

interval of 0.5.

15. Pitch Control Surface(s) Full Range … +/- deg. Unless Higher 0.5 or 0.25 for 0.2% of full range... For airplanes fitted

Position.\6\. Accuracy Uniquely airplanes operated with multiple or

Required. under Sec. split surfaces, a

121.344(f). suitable combination

of inputs is

acceptable in lieu

or recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sampling

interval of 0.5 or

0.25.

16. Lateral Control Surface(s) Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range... A suitable

Position.\7\. Higher Accuracy airplanes operated combination of

Uniquely Required. under Sec. surface position

121.344(f). sensors is

acceptable in lieu

of recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sampling

interval of 0.5 or

0.25.

17. Yaw Control Surface(s) Full Range … +/-2 deg. Unless 0.5 … 0.2% of full range... For airplanes with

Position.\8\. Higher Accuracy multiple or split

Uniquely Required. surfaces, a suitable

combination of

surface position

sensors is

acceptable in lieu

of recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sapling

interval of 0.5.

19. Pitch Trim Surface Position.\9\ Full Range … +/-3 deg. Unless 1 … 0.3% of full range...

Higher Accuracy

Uniquely Required.

20. Trailing Edge Flap or Cockpit Full Range or Each +/-3 deg. or as 2 … 0.5% of full range... Flap position and

Control Selection.\10\. Position (discrete). Pilot's indicator. cockpit control may

each be sampled at 4

second intervals, to

give a data point

every 2 seconds.

21. Leading Edge Flap or Cockpit Full Range or Each +/-3 deg. or as 2 … 0.5% of full range... Left and right sides,

Control Selection.\11\. Discrete Position. Pilot's indicator and or flap position and

sufficient to cockpit control may

determine each each be sampled at 4

discrete position. second intervals, so

as to give a data

point every 2

seconds.

23. Ground Spoiler Position or Full Range or Each +/-2 deg. Unless 1 or 0.5 for 0.2% of full range...

Speed Brake Selection.\12\. Position (discrete). Higher Accuracy airplanes operated

Uniquely Required. under Sec.

121.344(f).

24. Outside Air Temperature or -50 deg.C to +90 deg.C +/-2 deg.C … 2 … 0.3 deg.C …

Total Air Temperature.\13\.

37. Drift Angle.\15\ … As installed … As installed … 4 … 0.1 deg …

42. Throttle/power Leverl Full Range … +/-2% … 1 for each lever … 2% of full range … For airplanes with

position.\16\. non-mechanically

linked cockpit

engine controls.

57. Thrust command.\17\ … Full Range … +/-2% … 2 … 2% of full range …

Part 121 [Corrected]

Part 121 [Corrected]

Appendix E [Corrected]

2. Correct appendix E to part 125, by revising item numbers 1, 7, 9, 12b, 13b, 14a, 15, 16, 17, 19, 20, 21, 23, 24, 37, 42 and 57 to read as follows (Note: The footnote text remains unchanged):

Accuracy (sensor Seconds per sampling

Parameters Range input) interval Resolution Remarks

Appendix E [Corrected]

1. Time or Relative Times 24 Hrs, 0 to 4095 … +/-0.125% Per Hour.... 4 … 1 sec … UTC time preferred

Counts.\1\. when available.

Count increments

each 4 seconds of

system operation.

7. Roll Attitude \2\ … +/-180 deg … +/-2 deg … 1 or 0.5 for 0.5 deg … A sampling rate of

airplanes operated 0.5 is recommended.

under Sec.

121.344(f).

9. Thrust/Power on Each Engine- Full Range Forward.... +/-2% … 1 (per engine) … 0.2% of full range... Sufficient parameters

primary flight crew reference.\14\. (e.g. EPR, N1 or

Torque, NP) as

appropriate to the

particular engine be

recorded to

determine power in

forward and reverse

thrust, including

potential over-speed

condition.

12b. Pitch Control(s) position (fly- Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range...

by-wire systems).\3\. Higher Accuracy airplanes operated

Uniquely Required. under Sec.

121.344(f).

13b. Lateral Control position(s) Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range...

(fly-by-wire).\4\. Higher Accuracy airplanes operated

Uniquely Required. under Sec.

121.344(f).

14a. Yaw Control position(s) (non- Full Range … +/-2 deg. Unless 0.5 … 0.2% of full range... For airplanes that

fly-by-wire).\5\. Higher Accuracy have a flight

Uniquely Required. control break away

capability that

allows either pilot

to operate the

controls

independently,

record both control

inputs. The control

inputs may be

sampled alternately

once per second to

produce the sampling

interval of 0.5.

15. Pitch Control Surface(s) Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range... For airplanes fitted

Position.\6\. Higher Accuracy airplanes operated with multiple or

Uniquely Required. under Sec. split surfaces, a

121.344(f). suitable combination

of inputs is

acceptable in lieu

or recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sampling

interval of 0.5 or

0.25.

16. Lateral Control Surface(s) Full Range … +/-2 deg. Unless 0.5 or 0.25 for 0.2% of full range... A suitable

Position.\7\. Higher Accuracy airplanes operated combination of

Uniquely Required. under Sec. surface position

121.344(f). sensors is

acceptable in lieu

of recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sampling

interval of 0.5 or

0.25.

17. Yaw Control Surface(s) Full Range … +/-2 deg. Unless 0.5 … 0.2% of full range... For airplanes with

Position.\8\. Higher Accuracy multiple or split

Uniquely Required. surfaces, a suitable

combination of

surface position

sensors is

acceptable in lieu

of recording each

surface separately.

The control surfaces

may be sampled

alternately to

produce the sapling

interval of 0.5.

19. Pitch Trim Surface Position.\9\ Full Range … +/-3 deg. Unless 1 … 0.3% of full range...

Higher Accuracy

Uniquely Required.

20. Trailing Edge Flap or Cockpit Full Range or Each +/-3 deg. or as 2 … 0.5% of full range... Flap position and

Control Selection.\10\. Position (discrete). Pilot's indicator. cockpit control may

each be sampled at 4

second intervals, to

give a data point

every 2 seconds.

21. Leading Edge Flap or Cockpit Full Range or Each +/-3 deg. or as 2 … 0.5% of full range... Left and right sides,

Control Selection.\11\. Discrete Position. Pilot's indicator and or flap position and

sufficient to cockpit control may

determine each each be sampled at 4

discrete position. second intervals, so

as to give a data

point every 2

seconds.

23. Ground Spoiler Position or Full Range or Each +/-2 deg. Unless 1 or 0.5 for 0.2% of full range...

Speed Brake Selection.\12\. Position (discrete). Higher Accuracy airplanes operated

Uniquely Required. under Sec.

121.344(f).

24. Outside Air Temperature or -50 deg.C to +90 deg.C +/-2 deg.C … 2 … 0.3 deg.C …

Total Air Temperature.\13\.

37. Drift Angle.\15\ … As installed … As installed … 4 … 0.1% …

42. Throttle/power lever Full Range … +/-2% … 1 for each lever … 2% of full range … For airplanes with

position.\16\. non-mechanically

linked cockpit

engine controls.

57. Thrust command.\17\ … Full Range … +/-2% … 2 … 2% of full range …

Issued in Washington, DC, on December 18, 2000. Donald P. Byrne, Assistant Chief Counsel for Regulations.