Radar Vectors
Handbook Current Issued 2023 677 pages Copy saved Nov 20, 2026

FAA-H-8083-30B AMT Handbook—General

Official source ↗ Open PDF

Text read by OCR from a scanned file (2 of 677 pages). Check the original, as some words may be misread.

Aviation

FAA-H-8083-30B

Maintenance

Technician

Handbook-

General

35 30 28 26 30

luel U.S.Deparlmen 20 of Transportation

Federal Aviation 10 Administration

40 50 60 30 -20 80

—10 90

Aviation Maintenance Technician Handbook–General

U.S. Department of Transportation FEDERAL AVIATION ADMINISTRATION

Flight Standards Service

2023

ii

The Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B) was developed as one of a series of three handbooks for persons preparing for mechanic certification with airframe or powerplant ratings, or both. It is intended that this handbook will provide basic information on principles, fundamentals, and technical procedures in the subject matter areas common to both the airframe and powerplant ratings. Emphasis in this volume is on theory and methods of application.

The handbook is designed to aid students enrolled in a formal course of instruction preparing for FAA certification as a maintenance technician as well as for current technicians who wish to improve their knowledge. This volume contains information on mathematics, aircraft drawings, weight and balance, aircraft materials, processes and tools, physics, electricity, inspection, ground operations, and FAA regulations governing the certification and work of maintenance technicians. New to this volume is a section addressing how successful aviation maintenance technicians incorporate knowledge and awareness of ethics, professionalism and human factors in the field.

Because there are so many different types of airframes and powerplants in use today, it is reasonable to expect that differences exist in the components and systems of each. To avoid undue repetition, the practice of using representative systems and units is implemented throughout the handbook. Subject matter treatment is from a generalized point of view, and should be supplemented by reference to manufacturers’ manuals or other publications if more detail is desired. This handbook is not intended to replace, substitute for, or supersede official regulations or the manufacturers’ instructions.

The companion handbooks to Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B) are the Aviation Maintenance Technician Handbook–Airframe (FAA-H-8083-31 (as amended)), and the Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32 (as amended)).

This handbook is available for download, in pdf format, from www.faa.gov. Please visit this website for the latest version of all FAA handbooks.

This handbook is published by the U.S. Department of Transportation, Federal Aviation Administration, Airman Testing Standards Branch, AFS-630, P.O. Box 25082, Oklahoma City, OK 73125.

Comments regarding this publication should be emailed to [email protected].

Preface

iii

The Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B) was produced by the Federal Aviation Administration (FAA). The FAA wishes to acknowledge the following contributors:

• AERO Specialties, Inc. (www.aerospecialties.com) for images used in Chapter 1

• Dtom, Wikimedia Commons, for imagery used in Chapter 1

• Rama, Wikimedia Commons, Cc-by-sa-2.0-fr, for imagery used in Chapter 1

• ATA e-Business Program (www.ataebiz.org), for the ATA iSpec 2200 Standard Numbering System sample used in Chapters 2, 6, and 10

• Avsoft International for images used in Chapter 4

• Genesys Aerosystems (www.genesys-aerosystems.com) for images used in Chapter 4

• Plustar (www.plustar.com) Fluid/Pneumatic Line Identification Tapes for images used in Chapter 4

• Burkhard Domke (http://www.b-domke.de/AviationImages.html) for imagery used in Chapter 5

• Adrian Pingstone for imagery used in Chapter 5

• Elisabeth Klimesch for imagery used in Chapter 5

• Jcmurphy, Wikimedia Commons, for imagery used in Chapter 5

• Paul Hamilton for imagery used in Chapter 5

• Larry Jackson with Jackson Aircraft Weighing Service (www.jawsscales.com) for images used in Chapter 6

• Paul New with Tennessee Aircraft Services, Inc. (www.tennesseeaircraft.net) for images used in Chapter 6

• Tysto, Wikimedia Commons, for imagery used in Chapter 6

• Immaculate Flight (www.immaculateflight.com) for images used in Chapter 8

• Jaypee, Wikimedia Commons, for imagery used in Chapter 8

• Graham Tool Co., Inc. (www.grahamtool.com) for images used in Chapter 9

• Permaswage (www.permaswage.com) for images used in Chapter 9

• Stride Tool, Inc. (www.stridetool.com) for images used in Chapter 9

• Winton Machine Company (www.wintonmachine.com) for images used in Chapter 9

• Buehler, a Division of Illinois Tool Works Inc. (www.buehler.com) for images used in Chapter 10

• Illinois Tool Works Inc., through its ITW Magnaflux Division for images used in Chapter 10

• Intertek (www.intertek.com) for images used in Chapter 10

• Mike Richman with Quality Digest (www.qualitydigest.com) for images used in Chapter 10

• Olympus (www.olympus-ims.com) for images used in Chapter 10

• The Transportation Safety Board of Canada (TSB) for images used in Chapter 10

• Victor Sloan with Victor Aviation (www.victor-aviation.com) for images used in Chapter 10

• SNAP-ON® Incorporated (store.snapon.com) for images used in Chapter 11

• The L.S. Starrett Company (www.starrett.com) for images used in Chapter 11

• Alabama Aviation College, A Unit of Enterprise State for imagery used in Chapter 12

• Binarysequence, Wikimedia Commons, for imagery used in Chapter 12

• Siglent Technologies Co., Ltd. For imagery used in Chapter 12

Acknowledgments

iv

Chapter 1 Safety, Ground Operations, & Servicing … 1-1 Shop Safety … 1-1

Electrical Safety … 1-1

Physiological Safety … 1-1 Fire Safety … 1-1 Safety Around Compressed Gases … 1-2 Safety Around Hazardous Materials … 1-2 Safety Around Machine Tools … 1-2 Flight Line Safety … 1-4

Hearing Protection … 1-4 Foreign Object Damage (FOD) … 1-4 Safety Around Airplanes … 1-4 Safety Around Helicopters … 1-4 Fire Safety … 1-5 Fire Protection … 1-5

Requirements for Fire to Occur … 1-5 Classification of Fires … 1-5 Types and Operation of Shop and Flight Line Fire Extinguishers … 1-5 Inspection of Fire Extinguishers … 1-7 Identifying Fire Extinguishers … 1-8 Using Fire Extinguishers … 1-8 Tie-Down Procedures … 1-8

Preparation of Aircraft … 1-8 Tie-Down Procedures for Land Planes … 1-8

Securing Light Aircraft … 1-8 Securing Heavy Aircraft … 1-8 Tie-Down Procedures for Seaplanes … 1-8 Tie-Down Procedures for Ski Planes … 1-9 Tie-Down Procedures for Helicopters … 1-10 Procedures for Securing Weight-Shift-Control...1-11 Procedures for Securing Powered Parachutes..1-11 Ground Movement of Aircraft … 1-11

Engine Starting and Operation … 1-11 Reciprocating Engines … 1-11 Hand Cranking Engines … 1-13 Extinguishing Engine Fires … 1-14 Turboprop Engines … 1-14 Turboprop Starting Procedures … 1-15 Turbofan Engines … 1-15 Starting a Turbofan Engine … 1-15 Auxiliary Power Units (APUs) … 1-16 Unsatisfactory Turbine Engine Starts … 1-17

Hot Start … 1-17

False or Hung Start … 1-17 Engine Fails to Start … 1-17 Towing of Aircraft … 1-17 Taxiing Aircraft … 1-19

Taxi Signals … 1-20 Servicing Aircraft … 1-20

Servicing Aircraft Air/Nitrogen Oil & Fluids … 1-20 Ground Support Equipment … 1-21

Electric Ground Power Units … 1-21 Hydraulic Ground Power Units … 1-22 Ground Support Air Units … 1-23 Ground Air Heating and Air Conditioning … 1-24 Oxygen Servicing Equipment … 1-24 Oxygen Hazards … 1-25 Fuel Servicing of Aircraft … 1-25

Types of Fuel and Identification … 1-25 Contamination Control … 1-25 Fueling Hazards … 1-26 Fueling Procedures … 1-26 Defueling … 1-28

Chapter 2 Regulations, Maintenance Forms, Records, & Publications … 2-1 Overview — Title 14 of the Code of Federal Regulations (14 CFR) … 2-1

Title 14 CFR Part 3—General Requirements … 2-1 Maintenance-Related Regulations … 2-3

14 CFR Part 1—Definitions and Abbreviations … 2-3 14 CFR Part 21—Certification Procedures for Products and Articles … 2-3 14 CFR Part 23—Airworthiness Standards: Normal, Utility, Acrobatic, and Commuter Category Airplanes … 2-4 14 CFR Part 25—Airworthiness Standards: Transport Category Airplanes … 2-5 14 CFR Part 27—Airworthiness Standards: Normal Category Rotorcraft … 2-5 14 CFR Part 29—Airworthiness Standards: Transport Category Rotorcraft … 2-5 14 CFR Part 33—Airworthiness Standards: Aircraft Engines … 2-8 14 CFR Part 35—Airworthiness Standards: Propellers … 2-8

Table of Contents

v

14 CFR Part 39—Airworthiness Directives … 2-8 14 CFR Part 43—Maintenance, Preventive Maintenance, Rebuilding, and Alteration … 2-8 14 CFR Part 45—Identification and Registration Marking … 2-8 14 CFR Part 47—Aircraft Registration … 2-10 14 CFR Part 65—Certification: Airmen Other Than Flight Crewmembers … 2-10 14 CFR Part 91—General Operating and Flight Rules … 2-10 14 CFR Part 119—Certification: Air Carriers and Commercial Operators … 2-10 14 CFR Part 121—Operating Requirements: Domestic, Flag, and Supplemental Operations … 2-11 14 CFR Part 125—Certification and Operations: Airplanes Having a Seating Capacity of 20 or More Passengers or a Maximum Payload Capacity of 6,000 Pounds or More; and Rules Governing Persons on Board Such Aircraft … 2-12 14 CFR Part 135—Operating Requirements: Commuter and On-Demand Operations and Rules Governing Persons on Board Such Aircraft … 2-12 14 CFR Part 145—Repair Stations … 2-13 14 CFR Part 147—Aviation Maintenance Technician Schools … 2-13 14 CFR Part 183—Representatives of the Administrator … 2-13 Explanation of Primary Regulations (Parts 43 and 91) … 2-14

14 CFR Part 43—Maintenance, Preventative Maintenance Rebuilding, and Alteration … 2-14

Section 43.1—Applicability … 2-14 Section 43.2—Records of Overhaul and Rebuilding … 2-14 Section 43.3—Persons authorized to perform maintenance, preventive maintenance, rebuilding, and alterations … 2-14 Section 43.5—Approval for return to service after maintenance, preventive maintenance, rebuilding, and alterations … 2-15 Section 43.7—Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or component parts for return to service after maintenance, preventive maintenance, rebuilding, or alteration … 2-16 Section 43.9—Content, form and disposition of maintenance, preventive maintenance, rebuilding, and alteration

records (except inspection performed in accordance with parts 91 and 125, and sections 135.411(a)(1) and 135.419 of this chapter) … 2-16 Section 43.10—Disposition of Life-Limited Aircraft Parts … 2-16 Section 43.11—Content, form, and disposition of records for inspections conducted under parts 91 and 125, and sections 135.411(a)(1) and 135.419 of this chapter … 2-17 Section 43.12—Maintenance Records: Falsification, Reproduction, or Alteration … 2-17 Section 43.13—Performance Rules (General) … 2-17 Section 43.15—Additional Performance Rules for Inspections … 2-18 Section 43.16—Airworthiness Limitations.... 2-18 Section 43.17—Maintenance, preventive maintenance, or alterations performed on U.S. aeronautical products by certain Canadian persons … 2-18 Appendix A—Major Alterations, Major Repairs, and Preventive Maintenance … 2-18 Appendix B—Recording of Major Repairs and Major Alterations … 2-20 Appendix C—(Reserved) … 2-20 Appendix D—Scope and Detail of Items To Be Included in Annual and 100-Hour Inspections … 2-20 Appendix E—Altimeter System Test and Inspection … 2-20 Appendix F—ATC Transponder Tests and Inspections … 2-20 14 CFR Part 91—General Operating and Flight Rules … 2-21

Subpart A—General … 2-21 Subpart E—Maintenance, Preventive Maintenance, and Alterations … 2-21 Civil Air Regulations (CAR) … 2-23

CAR 3—Airplane Airworthiness—Normal, Utility, Aerobatic, and Restricted Purpose Categories … 2-23 CAR 4a—Airplane Airworthiness … 2-23 Suspected Unapproved Parts (SUP) … 2-24 Other FAA Documents … 2-24

Advisory Circulars (AC) … 2-24

The AC Numbering System … 2-26 Types of Airworthiness Directives (AD) … 2-26 AD Content … 2-26 AD Number … 2-26

vi

Applicability and Compliance … 2-27 Alternative Method of Compliance … 2-27 Special Airworthiness Information Bulletin (SAIB) … 2-27 Aircraft Specifications … 2-27 Supplemental Type Certificates (STC) … 2-27 Type Certificate Data Sheets (TCDS) … 2-30 FAA Handbooks & Manuals … 2-30 Non-FAA Documents … 2-30

Air Transport Association ATA iSpec 2200 … 2-30 Manufacturers’ Published Data … 2-30 Airworthiness Limitations … 2-33 Service Bulletins (SB) … 2-33 Structural Repair Manual (SRM) … 2-33 Forms … 2-33

Airworthiness Certificates … 2-33 Aircraft Registration … 2-37 Radio Station License … 2-38 FAA Form 337—Major Repair and Alteration ... 2-38 Records … 2-39

Making Maintenance Record Entries … 2-39 Temporary Records—14 CFR Part 91 Section 91.417(a)(1) and (b)(1) … 2-39 Permanent Records—14 CFR Part 91, Section 91.417(a)(2) and (b)(2) … 2-39 Electronic Records … 2-39 Light Sport Aircraft (LSA) … 2-40

Maintenance … 2-40 Aircraft Maintenance Manual (AMM) … 2-44 Line Maintenance, Repairs, & Alterations … 2-45 Major Repairs & Alterations … 2-45

Chapter 3 Mathematics in Aviation Maintenance … 3-1 Introduction … 3-1 Whole Numbers … 3-1

Addition of Whole Numbers … 3-1 Subtraction of Whole Numbers … 3-1 Division of Whole Numbers … 3-1 Fractions … 3-2

Finding the Least Common Denominator … 3-2 Addition of Fractions … 3-2 Subtraction of Fractions … 3-2 Multiplication of Fractions … 3-3 Division of Fractions … 3-3 Reducing Fractions … 3-3 Mixed Numbers … 3-3

Addition of Mixed Numbers … 3-4 Subtraction of Mixed Numbers … 3-4 The Decimal Number System … 3-4

Origin and Definition … 3-4

Addition of Decimal Numbers … 3-4 Subtraction of Decimal Numbers … 3-4 Multiplication of Decimal Numbers … 3-5 Division of Decimal Numbers … 3-6 Rounding Off Decimal Numbers … 3-6 Converting Decimal Numbers to Fractions … 3-6 Converting Fractions to Decimals … 3-7 Decimal Equivalent Chart … 3-7 Ratio … 3-7

Aviation Applications … 3-7 Proportion … 3-8

Extremes and Means … 3-8 Solving Proportions … 3-8 Percentage … 3-10

Expressing a Decimal Number as a Percentage … 3-10 Expressing a Percentage as a Decimal Number … 3-10 Expressing a Fraction as a Percentage … 3-10 Finding a Percentage of a Given Number … 3-10 Finding What Percentage One Number is of Another … 3-10 Finding a Number When a Percentage of it is Known … 3-11 Positive & Negative Numbers (Signed Numbers).3-11

Addition of Positive & Negative Numbers … 3-11 Subtraction of Positive & Negative Numbers … 3-11 Multiplication of Positive & Negative Numbers..3-11 Powers … 3-11

Special Powers … 3-12

Squared … 3-12 Cubed … 3-12 Power of Zero … 3-12 Law of Exponents … 3-12 Powers of Ten … 3-12 Roots … 3-12 Square Roots … 3-12 Cube Roots … 3-13 Fractional Powers … 3-13 Functions of Numbers Chart … 3-13 Scientific Notation … 3-13

Converting Numbers from Standard Notation to Scientific Notation … 3-13 Converting Numbers from Scientific Notation to Standard Notation … 3-16 Addition, Subtraction, Multiplication, and Division of Scientific Numbers … 3-16 Algebra … 3-16

Equations … 3-16 Algebraic Rules … 3-16 Solving for a Variable … 3-16

vii

Use of Parentheses … 3-17 Order of Operation … 3-17 Order of Operation for Algebraic Equations … 3-18 Computing Area of Two-Dimensional Solids … 3-18

Rectangle … 3-18 Square … 3-18 Triangle … 3-18 Parallelogram … 3-18 Trapezoid … 3-18 Circle … 3-19 Ellipse … 3-19 Units of Area … 3-20 Computing Volume of Three-Dimensional Solids.3-20

Rectangular Solid … 3-20 Cube … 3-21 Cylinder … 3-21 Sphere … 3-22 Cone … 3-23 Units of Volume … 3-23 Computing Surface Area of Three-Dimensional Solids … 3-23

Rectangular Solid … 3-24 Cube … 3-24 Cylinder … 3-24 Sphere … 3-24 Cone … 3-24 Trigonometric Functions … 3-24

Right Triangle, Sides, and Angles … 3-24 Sine, Cosine, and Tangent … 3-25

Calculator Method: … 3-25 Trigonometry Table Method: … 3-25 Pythagorean Theorem … 3-25 Measurement Systems … 3-26

Conventional (U.S. or English) System … 3-26 Metric System … 3-26 Measurement Systems & Conversions … 3-26 The Binary Number System … 3-27

Place Values … 3-27 Converting Binary Numbers to Decimal Numbers … 3-27 Converting Decimal Numbers to Binary Numbers … 3-27

Chapter 4 Aircraft Drawings … 4-1 Introduction … 4-1 Computer Graphics … 4-1 Purpose & Function of Aircraft Drawings … 4-1 Care & Use of Drawings … 4-2 Types of Drawings … 4-2

Detail Drawing … 4-2

Assembly Drawing … 4-2 Installation Drawing … 4-2 Sectional View Drawings … 4-2

Full Section … 4-2 Half Section … 4-2 Revolved Section … 4-2 Removed Section … 4-3 Title Blocks … 4-3

Drawing or Print Numbers … 4-3 Reference and Dash Numbers … 4-3 Universal Numbering System … 4-3 Drawing Standards … 4-7 Bill of Material … 4-7 Other Drawing Data … 4-8

Revision Block … 4-8 Notes … 4-8 Zone Numbers … 4-8 Station Numbers & Location Identification on Aircraft … 4-8 Allowances & Tolerances … 4-9 Finish Marks … 4-9 Scale … 4-9 Application … 4-9 Methods of Illustration … 4-9

Applied Geometry … 4-9

Orthographic Projection Drawings … 4-9 Pictorial Drawings … 4-11 Diagrams … 4-11 Flowcharts … 4-13 Lines and Their Meanings … 4-16

Centerlines … 4-16 Dimension Lines … 4-17 Extension Lines … 4-17 Sectioning Lines … 4-17 Phantom Lines … 4-17 Break Lines … 4-18 Leader Lines … 4-18 Hidden Lines … 4-18 Outline or Visible Lines … 4-18 Stitch Lines … 4-18 Cutting Plane and Viewing Plane Lines … 4-19 Drawing Symbols … 4-19

Material Symbols … 4-19 Shape Symbols … 4-19 Electrical Symbols … 4-19 Reading and Interpreting Drawings … 4-19 Drawing Sketches … 4-22

Sketching Techniques … 4-22 Basic Shapes … 4-22 Repair Sketches … 4-22 Care of Drafting Instruments … 4-22

viii

Graphs & Charts … 4-23

Reading & Interpreting Graphs & Charts … 4-23 Nomograms … 4-23 Microfilm & Microfiche … 4-23 Digital Images … 4-23

Chapter 5 Physics for Aviation … 5-1 Matter … 5-1

Characteristics of Matter … 5-1

Mass & Weight … 5-1 Attraction … 5-1 Porosity … 5-1 Impenetrability … 5-1 Density … 5-2 Specific Gravity … 5-2 Energy … 5-2

Potential Energy … 5-2 Kinetic Energy … 5-3 Force, Work, Power, & Torque … 5-4

Force … 5-4 Work … 5-4 Friction & Work … 5-4

Static Friction … 5-5 Sliding Friction … 5-5 Rolling Friction … 5-6 Power … 5-6 Torque … 5-6 Simple Machines … 5-7

Mechanical Advantage of Machines … 5-7 The Lever … 5-8

First Class Lever … 5-8 Second Class Lever … 5-9 Third Class Lever … 5-9 The Pulley … 5-9

Single Fixed Pulley … 5-9 Single Movable Pulley … 5-9 Block and Tackle … 5-10 The Gear … 5-10 Inclined Plane … 5-11 Stress … 5-12

Tension … 5-12 Compression … 5-13 Torsion … 5-13 Bending … 5-13 Shear … 5-13 Strain … 5-14 Motion … 5-14

Uniform Motion … 5-14 Speed and Velocity … 5-14

Acceleration … 5-15 Newton’s Law of Motion … 5-16

First Law … 5-16 Second Law … 5-16 Third Law … 5-17 Circular Motion … 5-17 Heat … 5-18

Heat Energy Units … 5-18 Heat Energy and Thermal Efficiency … 5-19 Heat Transfer … 5-19

Conduction … 5-19 Convection … 5-20 Radiation … 5-20 Specific Heat … 5-21 Temperature … 5-21 Thermal Expansion/Contraction … 5-22 Pressure … 5-22

Gauge Pressure … 5-23 Absolute Pressure … 5-23 Differential Pressure … 5-23 Gas Laws … 5-23

Boyle’s Law … 5-24 Charles’ Law … 5-25 General Gas Law … 5-25 Dalton’s Law … 5-25 Fluid Mechanics … 5-26

Buoyancy … 5-26 Fluid Pressure … 5-27 Pascal’s Law … 5-27 Bernoulli’s Principle … 5-29 Sound … 5-30

Wave Motion … 5-30 Speed of Sound … 5-31 Mach Number … 5-31 Frequency of Sound … 5-31 Loudness … 5-32 Measurement of Sound Intensity … 5-32 Doppler Effect … 5-32 Resonance … 5-32 The Atmosphere … 5-32

Composition of the Atmosphere … 5-33 Atmospheric Pressure … 5-34 Atmospheric Density … 5-34 Water Content of the Atmosphere … 5-34

Absolute Humidity … 5-35 Relative Humidity … 5-35 Dew Point … 5-36 Vapor Pressure … 5-36 Standard Atmosphere … 5-36 Aircraft Theory of Flight … 5-36

ix

Four Forces of Flight … 5-36 Bernoulli’s Principle and Subsonic Flow … 5-37 Lift and Newton’s Third Law … 5-37 Airfoils … 5-38

Camber … 5-38 Chord Line … 5-38 Relative Wind … 5-38 Angle of Attack … 5-38 Boundary Layer Airflow … 5-39

Boundary Layer Control … 5-39 Wingtip Vortices … 5-40 Axes of an Aircraft … 5-40 Aircraft Stability … 5-40

Static Stability … 5-40 Dynamic Stability … 5-40 Longitudinal Stability … 5-41 Lateral Stability … 5-42 Directional Stability … 5-42 Dutch Roll … 5-42 Flight Control Surfaces … 5-42

Flight Controls & the Lateral Axis … 5-42 Flight Controls and the Longitudinal Axis … 5-43 Flight Controls and the Vertical Axis … 5-43 Tabs … 5-44 Supplemental Lift-Modifying Devices … 5-45 High-Speed Aerodynamics … 5-46

Compressibility Effects … 5-46 The Speed of Sound … 5-46 Subsonic, Transonic, and Supersonic Flight. 5-47 Shock Waves … 5-47 High-Speed Airfoils … 5-48 Aerodynamic Heating … 5-49 Helicopter Aerodynamics … 5-49

Helicopter Structures and Airfoils … 5-49 Helicopter Axes of Flight … 5-52 Helicopters in Flight … 5-54 Weight-Shift Control, Flexible Wing Aircraft Aerodynamics … 5-56 Powered Parachute Aerodynamics … 5-58

Chapter 6 Aircraft Weight & Balance … 6-1 Introduction … 6-1 Requirements for Aircraft Weighing … 6-1 Weight & Balance Terminology … 6-2

Datum … 6-2 Arm … 6-2 Moment … 6-2 Center of Gravity (CG) … 6-3

Maximum Weight … 6-3 Empty Weight … 6-4 Empty Weight Center of Gravity (EWCG) … 6-4 Useful Load … 6-4 Minimum Fuel … 6-4 Tare Weight … 6-5 Procedures for Weighing an Aircraft … 6-5

General Concepts … 6-5 Weight and Balance Data … 6-6 Manufacturer-Furnished Information … 6-6 Weight and Balance Equipment … 6-7

Scales … 6-7

Spirit Level … 6-11 Hydrometer … 6-12 Preparing an Aircraft for Weighing … 6-12

Fuel System … 6-13 Oil System … 6-13 Miscellaneous Fluids … 6-14 Flight Controls … 6-14 Other Considerations … 6-14 Weighing Points … 6-14 Jacking the Aircraft … 6-14 Leveling the Aircraft … 6-14 Safety Considerations … 6-15 CG Range … 6-15

Empty Weight Center of Gravity (EWCG) Range … 6-15 Operating CG Range … 6-16 Standard Weights Used for Aircraft Weight and Balance … 6-16 Example Weighing of an Airplane … 6-16 EWCG Formulas … 6-16 Datum Forward of the Airplane–Nosewheel Landing Gear … 6-16 Datum Aft of the Main Wheels–Nosewheel Landing Gear … 6-17 Location of Datum … 6-17 Datum Forward of the Main Wheels–Tail Wheel Landing Gear … 6-17 Loading an Aircraft for Flight … 6-19

Example Loading of an Airplane … 6-19 Adverse-Loaded CG Checks … 6-20 Example Forward & Aft Adverse-Loaded CG Checks … 6-20 Equipment Change & Aircraft Alteration … 6-21

Example Calculation After an Equipment Change … 6-21 Use of Ballast … 6-22

Temporary Ballast … 6-22 Permanent Ballast … 6-23 Loading Graphs & CG Envelopes … 6-24

x

Helicopter Weight & Balance … 6-25

General Concepts … 6-25 Helicopter Weighing … 6-25 Weight and Balance—Weight-Shift Control Aircraft and Powered Parachutes … 6-26

Weight-Shift Control Aircraft … 6-27 Powered Parachutes … 6-28 Built-In Electronic Weighing … 6-28 Mean Aerodynamic Chord … 6-28 Weight & Balance Records … 6-31

Chapter 7 Aircraft Materials, Hardware, & Processes … 7-1

Properties of Metals … 7-1

Hardness … 7-1 Strength … 7-1 Density … 7-1 Malleability … 7-1 Ductility … 7-1 Elasticity … 7-1 Toughness … 7-1 Brittleness … 7-1 Fusibility … 7-2 Conductivity … 7-2 Thermal Expansion … 7-2 Ferrous Aircraft Metals … 7-2

Iron … 7-2 Steel and Steel Alloys … 7-2 Electrochemical Test … 7-4 Nonferrous Aircraft Metals … 7-5

Aluminum & Aluminum Alloys … 7-5 Wrought Aluminum … 7-7 Effect of Alloying Element … 7-7 Hardness Identification … 7-7 Magnesium & Magnesium Alloys … 7-8 Titanium and Titanium Alloys … 7-9 Copper and Copper Alloys … 7-10 Nickel & Nickel Alloys … 7-11 Substitution of Aircraft Metals … 7-11 Metalworking Processes … 7-12

Hot-Working … 7-12 Internal Structure of Metals … 7-14 Heat-Treating Equipment … 7-14 Heating … 7-15 Soaking … 7-15 Cooling … 7-16 Quenching Media … 7-16 Quenching Equipment … 7-16 Heat-Treatment of Ferrous Metals … 7-16

Behavior of Steel During Heating & Cooling.. 7-16 Hardening … 7-17 Hardening Precautions … 7-19 Tempering … 7-19 Annealing … 7-19 Normalizing … 7-19 Case Hardening … 7-20 Heat-Treatment of Nonferrous Metals … 7-20

Aluminum Alloys … 7-20 Alclad Aluminum … 7-21 Solution Heat-Treatment … 7-21 Quenching … 7-22 Lag Between Soaking & Quenching … 7-22 Reheat-Treatment … 7-22 Straightening After Solution Heat-Treatment.... 7-22 Precipitation Heat-Treating … 7-22

Precipitation Practices … 7-23 Annealing of Aluminum Alloys … 7-23 Heat-Treatment of Aluminum Alloy Rivets … 7-24 Heat-Treatment of Magnesium Alloys … 7-24

Solution Heat-Treatment … 7-24 Precipitation Heat-Treatment … 7-24 Heat-Treatment of Titanium … 7-25

Stress Relieving … 7-25 Full Annealing … 7-25 Thermal Hardening … 7-25 Case Hardening … 7-25 Hardness Testing … 7-25

Brinell Tester … 7-26 Rockwell Tester … 7-26 Barcol Tester … 7-27 Forging … 7-27 Casting … 7-28 Extruding … 7-28 Cold-Working/Hardening … 7-29 Nonmetallic Aircraft Materials … 7-29

Wood … 7-29 Plastics … 7-29 Transparent Plastics … 7-29 Composite Materials … 7-30

Advantages/Disadvantages of Composites... 7-30 Composite Safety … 7-31 Fiber Reinforced Materials … 7-31 Laminated Structures … 7-31 Reinforced Plastic … 7-31 Rubber … 7-32

Natural Rubber … 7-32 Synthetic Rubber … 7-32 Shock Absorber Cord … 7-33

xi

Seals … 7-33

Packings … 7-34

O-Ring Packings … 7-34 V-Ring Packings … 7-35 U-Ring Packings … 7-35 Gaskets … 7-35 Wipers … 7-35 Sealing Compounds … 7-35

One Part Sealants … 7-36 Two Part Sealants … 7-36 Aircraft Hardware … 7-36

Identification … 7-37 Threaded Fasteners … 7-37

Classification of Threads … 7-37 Aircraft Bolts … 7-37

General Purpose Bolts … 7-37 Close Tolerance Bolts … 7-38 Internal Wrenching Bolts … 7-38 Identification and Coding … 7-38 Special-Purpose Bolts … 7-39 Aircraft Nuts … 7-41

Non-Self-Locking Nuts … 7-41 Self-Locking Nuts … 7-42 Sheet Spring Nuts … 7-45 Internal & External Wrenching Nuts … 7-45 Identification & Coding … 7-45 Aircraft Washers … 7-46

Plain Washers … 7-46 Lock Washers … 7-46 Special Washers … 7-47 Installation of Nuts, Washers, & Bolts … 7-47

Bolt & Hole Sizes … 7-47 Installation Practices … 7-48 Safetying of Bolts & Nuts … 7-48

Repair of Damaged Internal Threads … 7-48 Fastener Torque … 7-49

Torque … 7-49 Torque Wrenches … 7-49 Torque Tables … 7-50 Cotter Pin Hole Line Up … 7-50 Aircraft Rivets … 7-51

Standards and Specifications … 7-51 Solid Shank Rivets … 7-52 Identification … 7-54 Blind Rivets … 7-56 Mechanically-Expanded Rivets … 7-57

Self-Plugging Rivets (Friction Lock) … 7-57 Pull-Thru Rivets … 7-57 Self-Plugging Rivets (Mechanical Lock) … 7-58

Material … 7-58 Head Styles … 7-59 Diameters … 7-59 Grip Length … 7-59 Rivet Identification … 7-59 Special Shear and Bearing Load Fasteners … 7-60

Pin Rivets … 7-60 Taper-Lok … 7-61 HI-LOK™ Fastening System … 7-61 HI-TIGUE™ Fastening System … 7-63 HI-LITE™ Fastening System … 7-64 Captive Fasteners … 7-64 Turn Lock Fasteners … 7-64 Dzus Fasteners … 7-64 Camloc Fasteners … 7-65 Airloc Fasteners … 7-66 Screws … 7-66

Structural Screws … 7-66 Machine Screws … 7-67 Self-Tapping Screws … 7-67 Identification & Coding for Screws … 7-67 Riveted & Rivetless Nut Plates … 7-68

Nut Plates … 7-68 Rivnuts … 7-68 Dill Lok-Skrus and Dill Lok-Rivets … 7-69 Deutsch Rivets … 7-70 Sealing Nut Plates … 7-70 Hole Repair & Hole Repair Hardware … 7-70

Repair of Damaged Holes with Acres Fastener Sleeves … 7-71 Control Cables & Terminals … 7-72 Push-Pull Tube Linkage … 7-72 Safetying Methods … 7-75

Pins … 7-75 Safety Wiring … 7-77

Nuts, Bolts, & Screws … 7-77 Oil Caps, Drain Cocks, & Valves … 7-77 Electrical Connectors … 7-79 Turnbuckles … 7-79 General Safety Wiring Rules … 7-80

Cotter Pin Safetying … 7-80 Snap Rings … 7-80

Chapter 8 Cleaning & Corrosion Control … 8-1 Corrosion … 8-1

Factors Affecting Corrosion … 8-1

Pure Metals … 8-1 Climate … 8-2

xii

Geographical Location … 8-2 Foreign Material … 8-2 Micro-organisms … 8-2 Manufacturing Processes … 8-2 Types of Corrosion … 8-2

Direct Chemical Attack … 8-2 Electrochemical Attack … 8-3 Forms of Corrosion … 8-5

Surface Corrosion … 8-5 Filiform Corrosion … 8-5 Pitting Corrosion … 8-6 Dissimilar Metal Corrosion … 8-6 Concentration Cell Corrosion … 8-6 Intergranular Corrosion … 8-7 Exfoliation Corrosion … 8-7 Stress-Corrosion/Cracking … 8-7 Fretting Corrosion … 8-9 Fatigue Corrosion … 8-9 Galvanic Corrosion … 8-10 Common Corrosive Agents … 8-10 Preventive Maintenance … 8-10 Inspection … 8-11 Corrosion Prone Areas … 8-11

Exhaust Trail Areas … 8-11 Battery Compartments and Battery Vent Openings … 8-12 Bilge Areas … 8-12 Lavatories, Buffets, & Galleys … 8-12 Wheel Well and Landing Gear … 8-12 Water Entrapment Areas … 8-12 Engine Frontal Areas & Cooling Air Vents … 8-13 Wing Flap & Spoiler Recesses … 8-13 External Skin Areas … 8-13 Electronic & Electrical Compartments … 8-13 Miscellaneous Trouble Areas … 8-13 Corrosion Removal … 8-14

Surface Cleaning and Paint Removal … 8-14 Fairing or Blending Reworked Areas … 8-15 Corrosion of Ferrous Metals … 8-15

Mechanical Removal of Iron Rust … 8-15 Chemical Removal of Rust … 8-16 Chemical Surface Treatment of Steel … 8-16 Removal of Corrosion from Highly Stressed Steel Parts … 8-17 Corrosion of Aluminum & Aluminum Alloys … 8-17

Treatment of Unpainted Aluminum Surfaces.... 8-18 Treatment of Anodized Surfaces … 8-19 Treatment of Intergranular Corrosion in Heat‑Treated Aluminum Alloy Surfaces … 8-19 Corrosion of Magnesium Alloys … 8-19

Treatment of Wrought Magnesium Sheet & Forgings … 8-19 Treatment of Installed Magnesium Castings … 8-19 Treatment of Titanium & Titanium Alloys … 8-20 Protection of Dissimilar Metal Contacts … 8-20

Contacts Not Involving Magnesium … 8-20 Contacts Involving Magnesium … 8-20 Corrosion Limits … 8-20 Processes & Materials Used in Corrosion Control … 8-21

Metal Finishing … 8-21 Surface Preparation … 8-21 Chemical Treatments … 8-22

Anodizing … 8-22 Alodizing … 8-22 Chemical Surface Treatment and Inhibitors … 8-22 Chromic Acid Inhibitor … 8-22 Sodium Dichromate Solution … 8-23 Chemical Surface Treatments … 8-23 Protective Paint Finishes … 8-23 Aircraft Cleaning … 8-23

Exterior Cleaning … 8-23 Interior Cleaning … 8-24

Types of Cleaning Operations … 8-24 Nonflammable Aircraft Cabin Cleaning Agents & Solvents … 8-25 Flammable & Combustible Agents … 8-25 Container Controls … 8-25 Fire Prevention Precautions … 8-25 Fire Protection Recommendations … 8-26 Powerplant Cleaning … 8-26 Solvent Cleaners … 8-27

Dry Cleaning Solvent … 8-27 Aliphatic and Aromatic Naphtha … 8-27 Safety Solvent … 8-27 Methyl Ethyl Ketone (MEK) … 8-27 Kerosene … 8-27 Cleaning Compound for Oxygen Systems … 8-27 Emulsion Cleaners … 8-28

Water Emulsion Cleaner … 8-28 Solvent Emulsion Cleaners … 8-28 Soaps & Detergent Cleaners … 8-28

Cleaning Compound, Aircraft Surfaces … 8-28 Nonionic Detergent Cleaners … 8-28 Mechanical Cleaning Materials … 8-28

Mild Abrasive Materials … 8-28 Abrasive Papers … 8-28 Chemical Cleaners … 8-29

Phosphoric-citric Acid … 8-29

xiii

Chapter 9 Fluid Lines & Fittings … 9-1 Introduction … 9-1 Rigid Fluid Lines … 9-1

Tubing Materials … 9-1

Copper … 9-1 Aluminum Alloy Tubing … 9-1 Steel … 9-1 Titanium 3AL–2.5V … 9-1 Material Identification … 9-1 Sizes … 9-2 Fabrication of Metal Tube Lines … 9-2

Tube Cutting … 9-2 Tube Bending … 9-2 Alternative Bending Methods … 9-3

Tube Flaring … 9-3 Instructions for Rolling-Type Flaring Tools … 9-4 Double Flaring … 9-5

Double Flaring Instructions … 9-5 Fittings … 9-5 Flareless Fittings … 9-5 Beading … 9-7 Fluid Line Identification … 9-7 Fluid Line End Fittings … 9-7

Universal Bulkhead Fittings … 9-8 AN Flared Fittings … 9-8 MS Flareless Fittings … 9-9

Swaged Fittings … 9-9 Cryofit Fittings … 9-9 Rigid Tubing Installation and Inspection … 9-10

Connection & Torque … 9-10 Flareless Tube Installation … 9-12 Rigid Tubing Inspection & Repair … 9-14 Flexible Hose Fluid Lines … 9-16

Hose Materials & Construction … 9-16

Buna-N … 9-16 Neoprene … 9-16 Butyl … 9-16 Hose Identification … 9-16 Flexible Hose Inspection … 9-18 Fabrication & Replacement of Flexible Hose.... 9-18

Flexible Hose Testing … 9-19 Size Designations … 9-19 Hose Fittings … 9-21 Installation of Flexible Hose Assemblies … 9-21

Slack … 9-21 Flex … 9-21 Twisting … 9-21 Bending … 9-21

Clearance … 9-21 Hose Clamps … 9-22

Chapter 10 Inspection Concepts & Techniques … 10-1 Basic Inspection … 10-1

Techniques/Practices … 10-1 Preparation … 10-1 Aircraft Logs … 10-1 Checklists … 10-2 Publications … 10-3

Manufacturers’ Service Bulletins/Instructions... 10-3 Maintenance Manual … 10-3 Overhaul Manual … 10-4 Structural Repair Manual … 10-4 Illustrated Parts Catalog … 10-4 Wiring Diagram Manual … 10-4 Code of Federal Regulations (CFRs) … 10-4 Airworthiness Directives (ADs) … 10-4 Type Certificate Data Sheets (TCDS) … 10-4 Routine/Required Inspections … 10-5

Preflight/Postflight Inspections … 10-5 Annual/100-Hour Inspections … 10-5 Progressive Inspections … 10-12 Continuous Inspections … 10-12 Altimeter & Transponder Inspections … 10-12 Air Transport Association iSpec 2200 … 10-12 Special Inspections … 10-12

Hard or Overweight Landing Inspection … 10-14 Severe Turbulence Inspection/Over “G” … 10-14 Lightning Strike … 10-16 Bird Strike … 10-16 Fire Damage … 10-16 Flood Damage … 10-16 Seaplanes … 10-16 Aerial Application Aircraft … 10-16 Special Flight Permits … 10-16 Nondestructive Inspection/Testing … 10-17

Training, Qualification, & Certification … 10-17 Advantages & Disadvantages of NDI Methods … 10-17 Visual Inspection … 10-17

Surface Cracks … 10-18 Borescope … 10-18 Interpretation of Results … 10-18 False Indications … 10-20 Eddy Current Inspection … 10-20

Basic Principles … 10-20 Principles of Operations … 10-21 Eddy Current Instruments … 10-21 Ultrasonic Inspection … 10-21

xiv

Pulse Echo … 10-22 Through-Transmission … 10-23 Resonance … 10-24 Ultrasonic Instruments … 10-26 Reference Standards … 10-26 Couplants … 10-26 Inspection of Bonded Structures … 10-26

Types of Defects … 10-28 Acoustic Emission Inspection … 10-28 Magnetic Particle Inspection … 10-29

Development of Indications … 10-29 Types of Discontinuities Disclosed … 10-29 Preparation of Parts for Testing … 10-30 Effect of Flux Direction … 10-30 Effect of Flux Density … 10-30 Magnetizing Methods … 10-31 Identification of Indications … 10-31 Magnaglo Inspection … 10-32

Magnetizing Equipment … 10-32 Indicating Mediums … 10-33 Demagnetizing … 10-33 Standard Demagnetizing Practice … 10-34 Radiographic … 10-34 Radiographic Inspection … 10-34

Preparation and Exposure … 10-34 Radiographic Interpretation … 10-35 Radiation Hazards … 10-36 Inspection of Composites … 10-36

Tap Testing … 10-36 Electrical Conductivity … 10-37 Thermography … 10-37 Inspection of Welds … 10-38

Chapter 11 Hand Tools & Measuring Devices … 11-1 General Purpose Tools … 11-1

Hammers & Mallets … 11-1 Screwdrivers … 11-1 Pliers & Plier-Type Cutting Tools … 11-3 Punches … 11-3 Wrenches … 11-4 Special Wrenches … 11-5 Torque Wrench … 11-5 Strap Wrenches … 11-6 Impact Drivers … 11-6 Metal Cutting Tools … 11-8

Hand Snips … 11-8 Hacksaws … 11-8 Chisels … 11-9 Files … 11-9

Care and Use … 11-10 Most Commonly Used Files … 11-10 Care of Files … 11-12 Drills … 11-12

Twist Drills … 11-12 Reamers … 11-13 Countersink … 11-14 Taps and Dies … 11-14 Layout and Measuring Tools … 11-14

Rules … 11-14 Combination Sets … 11-17 Scriber … 11-18 Dividers and Pencil Compasses … 11-19 Calipers … 11-19 Micrometer Calipers … 11-19 Micrometer Parts … 11-19 Reading a Micrometer … 11-22 Vernier Scale … 11-23 Using a Micrometer … 11-24 Slide Calipers … 11-25

Chapter 12 Fundamentals of Electricity & Electronics … 12-1 Introduction … 12-1 General Composition of Matter … 12-1

Matter … 12-1 Element … 12-1 Compound … 12-1 Molecule … 12-1 Atom … 12-1 Electrons, Protons, & Neutrons … 12-1 Electron Shells & Energy Levels … 12-2

Valence Electrons … 12-2 Ions … 12-2 Free Electrons … 12-2 Electron Movement … 12-2

Conductors, Insulators, and Semiconductors.12-2 Conductors … 12-3 Insulators … 12-3 Semiconductors … 12-4 Metric Based Prefixes Used for Electrical Calculations … 12-4 Static Electricity … 12-4

Attractive and Repulsive Forces … 12-4 Electrostatic Field … 12-5 Electrostatic Discharge (ESD) Considerations. 12-5 Magnetism … 12-6 Types of Magnets … 12-9 Electromagnetism … 12-12 Conventional Flow & Electron Flow … 12-14

Conventional Flow … 12-14

xv

Electron Flow … 12-14 Electromotive Force (Voltage) … 12-14 Current … 12-16 Ohm’s Law (Resistance) … 12-17 Resistance of a Conductor … 12-18

Factors Affecting Resistance … 12-18 Resistance and Relation to Wire Sizing … 12-20

Circular Conductors (Wires/Cables) … 12-20 Rectangular Conductors (Bus Bars) … 12-20 Power and Energy … 12-20

Power in an Electrical Circuit … 12-20 Power Formulas Used in the Study of Electricity … 12-21 Power in a Series & Parallel Circuit … 12-22 Energy in an Electrical Circuit … 12-22 Sources of Electricity … 12-22

Pressure Source … 12-22 Chemical Source … 12-23 Thermal Sources … 12-23 Light Sources … 12-23 Schematic Representation of Electrical Components … 12-23

Conductors … 12-23 Types of Resistors … 12-24

Fixed Resistor … 12-24 Carbon Composition … 12-24 Resistor Ratings … 12-24

Color Code … 12-24 Color Band Decoding … 12-25 Wire-Wound … 12-26 Variable Resistors … 12-26

Rheostat … 12-26 Potentiometer … 12-27 Thermistors … 12-27 Photoconductive Cells … 12-27 Circuit Protection Devices … 12-27

Fuse … 12-28 Current Limiter … 12-29 Circuit Breaker … 12-29

Arc Fault Circuit Breaker … 12-29 Thermal Protectors … 12-29 Control Devices … 12-30

Switches … 12-30 Toggle Switch … 12-30 Microswitches … 12-31 Rotary Selector Switches … 12-31 Pushbutton Switches … 12-31 Lighted Pushbutton Switches … 12-32 Dual In-Line Parallel (DIP) Switches … 12-33 Switch Guards … 12-33

Relays … 12-33 Series DC Circuits … 12-33

Voltage Drops & Further Application of Ohm’s Law … 12-35 Voltage Sources in Series … 12-36 Kirchhoff’s Voltage Law … 12-36 Voltage Dividers … 12-37 Determining the Voltage Divider Formula … 12-38 Parallel DC Circuits … 12-40

Voltage Drops … 12-40 Total Parallel Resistance … 12-40 Resistors in Parallel … 12-40 Two Resistors in Parallel … 12-40 Current Source … 12-41 Kirchhoff’s Current Law … 12-41 Current Dividers … 12-41 Series-Parallel DC Circuits … 12-42

Determining the Total Resistance … 12-42 Alternating Current (AC) & Voltage … 12-43

AC and DC Compared … 12-44 Generator Principles … 12-44

Generators of Alternating Current … 12-44

Position 1 … 12-45 Position 2 … 12-45 Position 3 … 12-45 Position 4 … 12-46 Position 5 … 12-46 Cycle and Frequency … 12-46

Cycle Defined … 12-46 Frequency Defined … 12-46 Period Defined … 12-47 Wavelength Defined … 12-47 Phase Relationships … 12-47

In Phase Condition … 12-48 Out of Phase Condition … 12-48 Values of Alternating Current … 12-48

Instantaneous Value … 12-48 Peak Value … 12-49 Effective Value … 12-49 Opposition to Current Flow of AC … 12-49 Capacitance … 12-50

Capacitors in Direct Current … 12-50 The Resistor/Capacitor (RC) Time Constant.. 12-50 Units of Capacitance … 12-50 Voltage Rating of a Capacitor … 12-51 Factors Affecting Capacitance … 12-51 Types of Capacitors … 12-51

Fixed Capacitors … 12-51 Ceramic … 12-51 Electrolytic … 12-52

xvi

Tantalum … 12-52 Polyester Film … 12-52 Oil Capacitors … 12-53

Variable Capacitors … 12-53 Trimmers … 12-53 Varactors … 12-53 Capacitors in Series … 12-53 Capacitors in Parallel … 12-54 Capacitors in Alternating Current … 12-54 Capacitive Reactance Xc … 12-54 Sample Problem: … 12-55 Solution: … 12-55 Capacitive Reactances in Series and in Parallel … 12-55 Phase of Current and Voltage in Reactive Circuits … 12-55 Inductance … 12-56

Characteristics of Inductance … 12-56 The RL Time Constant … 12-56 Physical Parameters … 12-56 Self-Inductance … 12-57 Types of Inductors … 12-57 Units of Inductance … 12-58 Inductors in Series … 12-58 Inductors in Parallel … 12-58 Inductive Reactance … 12-58 AC Circuits … 12-59

Ohm’s Law for AC Circuits … 12-59 Series AC Circuits … 12-59

Solution: … 12-60 Solution: … 12-61 Solution: … 12-62 Parallel AC Circuits … 12-62

Solution: … 12-62 Solution: … 12-62 Resonance … 12-63 Power in AC Circuits … 12-64 True Power Defined … 12-64

Apparent Power Defined … 12-64 Solution: … 12-65 Transformers … 12-65 Current Transformers … 12-67 Transformer Losses … 12-67 Power in Transformers … 12-67 DC Measuring Instruments … 12-67

D’Arsonval Meter Movement … 12-68 Current Sensitivity and Resistance … 12-68 Damping … 12-69 Electrical Damping … 12-69 Mechanical Damping … 12-69 A Basic Multirange Ammeter … 12-69

Precautions … 12-69 The Voltmeter … 12-70

Voltmeter Sensitivity … 12-70 Multiple Range Voltmeters … 12-70 Voltmeter Circuit Connections … 12-71 Influence of the Voltmeter in the Circuit … 12-71 The Ohmmeter … 12-71

Zero Adjustment … 12-71 Ohmmeter Scale … 12-71 The Multirange Ohmmeter … 12-72 Megger (Megohmmeter) … 12-72 AC Measuring Instruments … 12-73

Electrodynamometer Meter Movement … 12-74 Moving Iron Vane Meter … 12-74 Inclined Coil Iron Vane Meter … 12-75 Varmeters … 12-75 Wattmeter … 12-76 Frequency Measurement/Oscilloscope … 12-76 Horizontal Deflection … 12-77 Vertical Deflection … 12-77 Tracing a Sine Wave … 12-77 Control Features on an Oscilloscope … 12-77 Flat Panel Color Displays for Oscilloscopes... 12-78 Digital Multimeter … 12-78 Basic Circuit Analysis & Troubleshooting … 12-78

Voltage Measurement … 12-79 Current Measurement … 12-80 Checking Resistance in a Circuit … 12-80 Continuity Checks … 12-81 Capacitance Measurement … 12-81 Inductance Measurement … 12-81 Troubleshooting Open Faults in a Series Circuit … 12-82 Tracing Opens with the Voltmeter … 12-82 Tracing Opens with the Ohmmeter … 12-82 Troubleshooting Shorting Faults in a Series Circuit … 12-83 Tracing Shorts with the Ohmmeter … 12-83 Tracing Shorts with the Voltmeter … 12-84 Troubleshooting Open Faults in a Parallel Circuit … 12-84 Tracing an Open with an Ammeter … 12-85 Tracing an Open with an Ohmmeter … 12-85 Troubleshooting Shorting Faults in Parallel Circuits … 12-85 Troubleshooting Shorting Faults in Series- Parallel Circuits … 12-86

Logic in Tracing an Open … 12-86 Tracing Opens with the Voltmeter … 12-86 Batteries … 12-87

Primary Cell … 12-87

xvii

Secondary Cell … 12-87 Battery Ratings … 12-89 Life Cycle of a Battery … 12-89 Lead-Acid Battery Testing Methods … 12-90 Lead-Acid Battery Charging Methods … 12-91 Nickel-Cadmium Batteries … 12-91

Chemistry and Construction … 12-91 Operation of Nickel-Cadmium Cells … 12-92

General Maintenance and Safety Precautions … 12-92 Sealed Lead Acid (SLA) Batteries … 12-92 Lithium-Ion Batteries … 12-93 Inverters … 12-93

Rotary Inverters … 12-94 Permanent Magnet Rotary Inverter … 12-94 Inductor-Type Rotary Inverter … 12-94 Static Inverters … 12-94 Semiconductors … 12-95

Doping … 12-96 PN Junctions & the Basic Diode … 12-98 Forward Biased Diode … 12-98 Reverse Biased Diode … 12-99 Rectifiers … 12-100

Half-Wave Rectifier … 12-101 Full-Wave Rectifier … 12-102 Dry Disk … 12-102 Types of Diodes … 12-103

Power Rectifier Diodes … 12-103 Zener Diodes … 12-103 Special Purpose Diodes … 12-103 Light-Emitting Diode (LED) … 12-103 Liquid Crystal Displays (LCD) … 12-104 Photodiode … 12-104 Varactors … 12-104 Schottky Diodes … 12-105 Diode Identification … 12-105 Introduction to Transistors … 12-105

Classification … 12-105 Transistor Theory … 12-106 PNP Transistor Operation … 12-107 Identification of Transistors … 12-107 Field Effect Transistors … 12-107 Metal-Oxide-Semiconductor FET (MOSFET) . 12-108 Common Transistor Configurations … 12-108

Common-Emitter (CE) Configuration … 12-108 Common-Collector (CC) Configuration … 12-109 Common-Base (CB) Configuration … 12-109 Vacuum Tubes … 12-110 Filtering … 12-111

Filtering Characteristics of Capacitors … 12-111 Filtering Characteristics of Inductors … 12-111 Common Filter Configurations … 12-111 Basic LC Filters … 12-112

Low-Pass Filter … 12-112 High-Pass Filter (HPF) … 12-112 Band-Pass Filter … 12-112 Band-Stop Filter … 12-112 Amplifier Circuits … 12-113

Classification … 12-113

Class A … 12-114 Class AB … 12-114 Class B … 12-114 Class C … 12-114 Methods of Coupling … 12-115

Direct Coupling … 12-115 RC Coupling … 12-115 Impedance Coupling … 12-116 Transformer Coupling … 12-116 Feedback … 12-116 Operational Amplifiers (OP AMP) … 12-116

Applications … 12-117 Magnetic Amplifiers … 12-118

Saturable-Core Reactor … 12-119 Logic Circuits … 12-119

Logic Polarity … 12-120

Positive … 12-120 Negative … 12-120 Pulse Structure … 12-120 Basic Logic Circuits … 12-121

The Inverter Logic … 12-121 The AND Gate … 12-121 The OR Gate … 12-122 The NAND Gate … 12-122 The NOR Gate … 12-122 Exclusive OR Gate … 12-122 Exclusive NOR Gate … 12-122 The Integrated Circuit … 12-122 Microprocessors … 12-123 DC Generators … 12-123

Theory of Operation … 12-123 Generation of a DC Voltage … 12-125

Position A … 12-125 Position B … 12-126 Position C … 12-126 Position D … 12-127 The Neutral Plane … 12-127 Construction Features of DC Generators .... 12-128

Field Frame … 12-128

xviii

Armature … 12-130

Gramme-Ring Armature … 12-130 Drum-Type Armature … 12-130 Commutators … 12-130 Armature Reaction … 12-131 Compensating Windings … 12-131 Interpoles … 12-132 Types of DC Generators … 12-132

Series Wound DC Generators … 12-132 Shunt Wound DC Generators … 12-133 Compound Wound DC Generators … 12-134 Generator Ratings … 12-134 Generator Terminals … 12-135 DC Generator Maintenance … 12-135

Inspection … 12-135 Condition of Generator Brushes … 12-136 DC Motors … 12-137 Force Between Parallel Conductors … 12-138 Developing Torque … 12-138 Basic DC Motor … 12-138

Position A … 12-139 Position B … 12-139 Position C … 12-139 Position D … 12-139 DC Motor Construction … 12-140

Armature Assembly … 12-140 Field Assembly … 12-141 Brush Assembly … 12-141 End Frame … 12-141 Types of DC Motors … 12-141

Series DC Motor … 12-141 Shunt DC Motor … 12-142 Compound DC Motor … 12-142 Counter Electromotive Force (emf) … 12-142

Types of Duty … 12-143 Reversing Motor Direction … 12-144 Motor Speed … 12-145

Energy Losses in DC Motors … 12-145 Inspection and Maintenance of DC Motors... 12-146 AC Motors … 12-147

Types of AC Motors … 12-147 Three-Phase Induction Motor … 12-148 Rotating Magnetic Field … 12-148 Construction of Induction Motor … 12-148 Induction Motor Slip … 12-149 Single-Phase Induction Motor … 12-149 Shaded Pole Induction Motor … 12-149 Split-Phase Motor … 12-150 Capacitor Start Motor … 12-150 Direction of Rotation of Induction Motors … 12-150

Synchronous Motor … 12-151 AC Series Motor … 12-152 Maintenance of AC Motors … 12-153 Alternators … 12-154

Basic Alternators & Classifications … 12-154 Method of Excitation … 12-154 Number of Phases … 12-154 Armature or Field Rotation … 12-155

Single-Phase Alternator … 12-155 Two-Phase Alternator … 12-156 Three-Phase Alternator … 12-156 Wye Connection (Three-Phase) … 12-156 Delta Connection (Three-Phase) … 12-156 Alternator Rectifier Unit … 12-156 Brushless Alternator … 12-157 Alternator Frequency … 12-158 Starter Generator … 12-158 Alternator Rating … 12-158 Alternator Maintenance … 12-159 Regulation of Generator Voltage … 12-159 Voltage Regulation with a Vibrating-Type Regulator … 12-159 Three Unit Regulators … 12-161 Differential Relay Switch … 12-162 Overvoltage & Field Control Relays … 12-163 Generator Control Units (GCU) … 12-164

Basic Functions of a Generator Control Unit (GCU) … 12-164 Voltage Regulation … 12-164 Overvoltage Protection … 12-164 Parallel Generator Operations … 12-164 Over-Excitation Protection … 12-164 Differential Voltage … 12-164 Reverse Current Sensing … 12-164 Alternator Constant Speed Drive System … 12-164 Hydraulic Transmission … 12-165 Voltage Regulation of Alternators … 12-171

Alternator Transistorized Regulators … 12-172

Chapter 13 Mechanic Privileges & Limitations … 13-1 Introduction … 13-1 Mechanic Certification: Subpart A—General (by 14 CFR Section) … 13-1 Section 65.3, Certification of Foreign Airmen Other Than Flight Crewmembers … 13-1 Section 65.11, Application and Issue … 13-1 Section 65.12, Offenses Involving Alcohol and Drugs … 13-1 Section 65.13, Temporary Certificate … 13-1 Section 65.14, Security Disqualification … 13-1

xix

Section 65.15, Duration of Certificates … 13-1 Section 65.16, Change of Name: Replacement of Lost or Destroyed Certificate.. 13-2 Section 65.17, Test: General Procedure … 13-2 Section 65.18, Written Tests: Cheating or Other Unauthorized Content … 13-2 Section 65.19, Retesting After Failure … 13-2 Section 65.20, Applications, Certificates, Logbooks, Reports, and Records: Falsification, Reproduction, or Alteration … 13-2 Section 65.21, Change of Address … 13-2 Refusal to Submit to a Drug or Alcohol Test … 13-2 Mechanic Certification: Subpart D—Mechanics (by 14 CFR Section) … 13-3

Section 65.71, Eligibility Requirements: General … 13-3 Section 65.73, Ratings … 13-3 Section 65.75, Knowledge Requirements … 13-3 Section 65.77, Experience Requirements … 13-3 Section 65.79, Skill Requirements … 13-3 Section 65.80, Certificated Aviation Maintenance … 13-4 Technician School Students … 13-4 Section 65.81, General Privileges and Limitations … 13-4 Section 65.83, Recent Experience Requirements … 13-4 Section 65.85, Airframe Rating: Additional Privileges … 13-4 Section 65.87, Powerplant Rating: Additional Privileges … 13-4 Section 65.89, Display of Certificate … 13-4 Inspection Authorization (IA) (by 14 CFR Section) … 13-5

Section 65.91, Inspection Authorization … 13-5 Section 65.92, Inspection Authorization: Duration … 13-5 Section 65.93, Inspection Authorization: Renewal … 13-5 Section 65.95, Inspection Authorization: Privileges and Limitations … 13-6 Ethics … 13-6

A Scenario … 13-6

Final Observation … 13-7

Chapter 14 Human Factors … 14-1 Introduction … 14-1

FAA Involvement … 14-1 Importance of Human Factors … 14-1 Definitions of Human Factors … 14-1 What are Human Factors? … 14-2

Elements of Human Factors … 14-2

Clinical Psychology … 14-3 Experimental Psychology … 14-3 Anthropometry … 14-4 Computer Science … 14-4 Cognitive Science … 14-4 Safety Engineering … 14-4 Medical Science … 14-4 Organizational Psychology … 14-4 Educational Psychology … 14-5 Industrial Engineering … 14-5 History of Human Factors … 14-6

Evolution of Maintenance Human Factors … 14-7 The Pear Model … 14-9

People … 14-9 Environment … 14-9

Physical … 14-10 Organizational … 14-10 Actions … 14-10 Resources … 14-10 Human Error … 14-13

Types of Errors … 14-13

Unintentional … 14-13 Intentional … 14-13 Active & Latent … 14-13 The “Dirty Dozen” … 14-13

Lack of Communication … 14-13 Complacency … 14-14 Lack of Knowledge … 14-14 Distraction … 14-15 Lack of Teamwork … 14-16 Fatigue … 14-16 Lack of Resources … 14-18 Lack of Assertiveness … 14-22 Stress … 14-24

Physical Stressors … 14-24 Psychological Stressors … 14-24 Physiological Stressors … 14-25 Lack of Awareness … 14-26 Norms … 14-26 Example of Common Maintenance Errors … 14-28 Where to Get Information … 14-29

Federal Aviation Administration (FAA) … 14-30

FAA’s Maintenance Fatigue Section … 14-30 FAA Safety Team … 14-31 Other Resources … 14-31

System Safety Services … 14-31 Human Factors & Ergonomics Society (HFES) … 14-31 International Ergonomics Association (IEA).14-31

xx

Glossary … G-1 Index … I-1

Safety, Ground Operations, & Servicing

Chapter 1

Chapter 1

Aviation maintenance technicians (AMTs) devote a portion of their aviation career to ground handling and operating aircraft. Technicians also need to be proficient in operating ground support equipment. The complexity of support equipment and the hazards involved in the ground handling of aircraft require that maintenance technicians possess a detailed knowledge of safety procedures used in aircraft servicing, taxiing, run-up, and in the use of ground support equipment. The information provided in this chapter is intended as a general guide for safely servicing and operating aircraft.

Introducing human factors to aircraft maintenance personnel makes them aware of how it affects maintenance performance. Although there are many human factors involved when dealing with maintenance performance, several areas can be considered. Some of these include fatigue, deadline pressure, stress, distractions, poor communication skills, complacency, and lack of information. Maintenance technicians need to understand how human factors can impact their performance and safety while completing maintenance tasks.

Shop Safety

Shop Safety

Keeping the shop, hangars, and flight line clean is essential to safety and efficient maintenance. The highest standards of orderly work arrangements and cleanliness must be observed during the maintenance of aircraft. Where continuous work shifts are established, the outgoing shift removes and properly stores personal tools, rollaway boxes, work stands, maintenance stands, hoses, electrical cords, hoists, crates, and boxes that were needed for the work to be accomplished.

Signs are posted to indicate dangerous equipment or hazardous conditions. Additionally, there are signs that provide the location of first aid and fire equipment. Safety lanes, pedestrian walkways, and fire lanes are painted around the perimeter inside the hangars. This is a safety measure to prevent accidents and to keep pedestrian traffic out of work areas.

Safety is everyone’s business. However, technicians and supervisors must watch for their own safety and for the safety of others working around them. Communication is key to ensuring everyone’s safety. If other personnel are conducting their actions in an unsafe manner, communicate with them, reminding them of their safety and that of others around them.

Physiological Safety

Electrical Safety Physiological Safety Working with electrical equipment poses certain physiological safety hazards. When electricity is applied to the human body, it can create severe burns in the area of entrance and at the point of exit from the body. In addition, the nervous system is affected and can be damaged or destroyed. To safely deal with electricity, the technician must have a working knowledge of the principles of electricity and a healthy respect for its capability to do both work and damage.

Wearing or use of proper safety equipment can provide a psychological assurance and physically protect the user at the same time. The use of rubber gloves, safety glasses, rubber or grounded safety mats, and other safety equipment contributes to the overall safety of the technician working on or with electrical equipment.

Two factors that affect safety when dealing with electricity are fear and overconfidence. These two factors are major causes of accidents involving electricity. While a certain amount of respect for electrical equipment is healthy and a certain level of confidence is necessary, extremes of either can be deadly.

Lack of respect is often due to lack of knowledge. Personnel who attempt to work with electrical equipment and have no knowledge of the principles of electricity lack the skills to deal with electrical equipment safely. Overconfidence leads to risk taking. The technician who does not respect the capabilities of electricity will, sooner or later, become a victim of electricity’s power.

Fire Safety

Fire Safety Anytime current flows, whether during generation or transmission, a by-product is heat. The greater the current flow, the greater the amount of heat created. When this heat becomes too great, protective coatings on wiring and other electrical devices can melt, causing shorting. That in turn leads to more current flow and greater heat. This heat can become so great that metals can melt, liquids vaporize, and flammable substances ignite.

An important factor in preventing electrical fires is to keep the area around electrical work or electrical equipment

clean, uncluttered, and free of all unnecessary flammable substances. Ensure that all power cords, wires, and lines are free of kinks and bends that can damage the wire. Never place wires or cords where they may be walked on or run over by other equipment. When several wires inside a power cord are broken, the current passing through the remaining wires increases. This generates more heat than the insulation coatings on the wire are designed to withstand and can lead to a fire. Closely monitor the condition of electrical equipment. Repair or replace damaged equipment before further use.

Safety Around Compressed Gases

Safety Around Compressed Gases Compressed air, like electricity, is an excellent tool when it is under control. A typical nitrogen bottle set is shown in Figure 1-1. The following “dos and don’ts” apply when working with or around compressed gases:

• Inspect air hoses frequently for breaks and worn spots. Unsafe hoses must be replaced immediately.

• Keep all connections in a “no-leak condition.”

• Maintain in-line oilers, if installed, in operating condition.

• Ensure the system has water sumps installed and drained at regular intervals.

• Filter air used for paint spraying to remove oil and water.

• Never use compressed air to clean hands or clothing. Pressure can force debris into the flesh leading to infection.

• Never spray compressed air in the area of other personnel.

• Straighten, coil, and properly store air hoses when not in use.

• Many accidents involving compressed gases occur during aircraft tire mounting. To prevent possible personal injury, use tire dollies and other appropriate devices to mount or remove heavy aircraft tires.

Figure 1-1: picture of page 24Figure 1-1 · page 24
Picture of the page from the copy saved here

When inflating tires on any type of aircraft wheels, always use tire cage guards. Extreme caution is required to avoid over inflation of high-pressure tires because of possible personal injury. Use pressure regulators on high-pressure air bottles to eliminate the possibility of over inflation of tires. Tire cages are not required when adjusting pressure in tires installed on an aircraft.

Safety Around Hazardous Materials

Safety Around Hazardous Materials Material safety diamonds are important with regard to shop safety. These diamond-shaped labels are a simple and quick way to determine the risk of hazardous material

within the associated container and, if used properly with the tags, indicate what personal safety equipment to use.

The most observable portion of the Safety Data Sheets (SDSs) (formerly known as Material Safety Data Sheet (MSDS)) label is the risk diamond. It is a four-color segmented diamond that represents flammability (red), reactivity (yellow), health (blue), and special hazard (white). In the flammability, reactivity, and health blocks, there is a number from 0 to 4. Zero represents little or no hazard to the user, while 4 means that the material is very hazardous. The special hazard segment contains a word or abbreviation to represent the specific hazard. Some examples are RAD for radiation, ALK for alkali materials, Acid for acidic materials, and CARC for carcinogenic materials. The letter W with a line through it stands for high reactivity to water. [Figure 1-2]

Figure 1-2: picture of page 24Figure 1-2 · page 24
Picture of the page from the copy saved here

The SDS is a more detailed version of the chemical safety issues. These forms have the detailed breakdown of the chemicals, including formulas and action to take if personnel come in contact with the chemicals. All sheets have the same information requirements; however, the exact location of the information on the sheet may vary depending on the SDS manufacturer. These forms are necessary for a safe shop that meets all the requirements of the governing safety body, the U.S. Department of Labor Occupational Safety and Health Administration (OSHA).

Safety Around Machine Tools

Safety Around Machine Tools Hazards in a shop increase when the operation of lathes, drill presses, grinders, and other types of machines are used. Each machine has its own set of safety practices. The following discussions are necessary to avoid injury.

The drill press can be used to bore and ream holes, to do facing, milling, and other similar types of operations. The following precautions can reduce the chance of injury:

• Wear eye protection.

• Securely clamp all work.

• Set the proper revolutions per minute (rpm) for the material used.

• Do not allow the spindle to feed beyond its limit of travel while drilling.

• Stop the machine before adjusting work or attempting to remove jammed work.

• Clean the area when finished.

Lathes are used in turning work of a cylindrical nature. This work may be performed on the inside or outside of the cylinder. The work is secured in the chuck to provide the rotary motion, and the forming is done by contact with a

Figure 1-1. A typical nitrogen bottle.

4

W

3 2

Figure 1-2. A risk diamond.

securely mounted tool. The following precautions can reduce the chance of injury:

• Wear eye protection.

• Use sharp cutting tools.

• Allow the chuck to stop on its own. Do not attempt to stop the chuck by hand pressure.

• Examine tools and work for cracks or defects before starting the work.

• Do not set tools on the lathe. Tools may be caught by the work and thrown.

• Before measuring the work, allow it to stop in the lathe.

Milling machines are used to shape or dress; cut gear teeth, slots, or key ways; and similar work. The following precautions can reduce the chance of injury:

• Wear eye protection.

• Clean the work bed prior to work.

• Secure the work to the bed to prevent movement

during milling.

• Select the proper tools for the job.

• Do not change the feed speed while working.

• Lower the table before moving under or away from the work.

• Ensure all clamps and bolts are passable under the arbor.

Grinders are used to sharpen tools, dress metal, and perform other operations involving the removal of small amounts of metal. The following precautions can reduce the chance of injury:

• Wear eye protection, even if the grinder has a shield.

• Inspect the grinding wheel for defects prior to use.

• Do not force grinding wheels onto the spindle. They fit snugly but do not require force to install them. Placing side pressure on a wheel could cause it to explode.

• Check the wheel flanges and compression washer. They should be one-third the diameter of the wheel.

• Do not stand in the arc of the grinding wheel while operating in case the wheel explodes.

Welding must be performed only in designated areas. Any part that is to be welded must be removed from the aircraft, if possible. Repair would then be accomplished in a controlled environment, such as a welding shop. A welding shop must be equipped with proper tables, ventilation, tool storage, and fire prevention and extinguishing equipment.

Welding on an aircraft should be performed outside, if possible. If welding in the hangar is necessary, observe these precautions:

• During welding operations, open fuel tanks and work on fuel systems are not permitted.

• Painting is not permitted.

• No aircraft are to be within 35 feet of the welding operation.

• No flammable material is permitted in the area around the welding operation.

• Only qualified welders are permitted to do the work.

• The welding area is to be roped off and placarded.

• Fire extinguishing equipment of a minimum rating of 20B must be in the immediate area with 80B rated equipment as a backup.

• Trained fire watches are to be present in the area around the welding operation.

• The aircraft being welded must be in a towable condition, with a tug attached, and the aircraft parking brakes released. A qualified operator must be on the tug and mechanics available to assist in the towing operation should it become necessary to tow the aircraft. If the aircraft is in the hangar, the hangar doors are to be open.

Flight Line Safety

Flight Line Safety

Hearing Protection The flight line is a place of dangerous activity. Technicians who perform maintenance on the flight line must constantly be aware of what is going on around them. The noise on a flight line comes from many places. Aircraft are only one source of noise. There are auxiliary power units (APUs), fuel trucks, baggage handling equipment, and so forth. Each has its own frequency of sound. Combined all together, the noise on the ramp or flight line can cause hearing loss.

Hearing Protection

There are many types of hearing protection available. Hearing protection can be external or internal. Earmuffs or headphones are considered external protection. The internal type of hearing protection fits into the auditory canal. Both types reduce the sound level reaching the eardrum and reduce the chances of hearing loss.

Hearing protection is essential when working with pneumatic drills, rivet guns, or other loud tools. Even short duration exposure to these sounds can cause hearing loss because of their high frequency. Continued exposure will cause hearing loss.

Foreign Object Damage (FOD)

Foreign Object Damage (FOD) Foreign object damage (FOD) is any damage to aircraft, personnel, or equipment caused by any loose object. These loose objects can be anything, such as broken runway concrete, shop towels, safety wire, etc. To control FOD, keep ramp and operation areas clean, have a tool control program, and provide convenient receptacles for used hardware, shop towels, and other consumables.

Never leave tools or other items around the intake of a turbine engine. The modern gas turbine engine creates a low-pressure area in front of the engine that causes any loose object to be drawn into the engine. The exhaust of these engines can propel loose objects great distances with enough force to damage anything that is hit. The importance of a FOD program cannot be overstressed when a technician considers the cost of engines, components, or a human life.

Safety Around Airplanes

Safety Around Airplanes As with the previously mentioned items, it is important to be aware of propellers. Technicians cannot assume the pilot of a taxiing aircraft can see them and must stay within the pilot’s view while on the ramp area. Turbine engine intakes and exhaust can also be very hazardous areas. Smoking or open flames are not permitted anywhere near an aircraft in operation. Be aware of aircraft fluids that can be detrimental to skin. When operating support equipment around aircraft, be sure to allow space between it and the aircraft, and secure it so it cannot roll into the aircraft. All items in the area of operating aircraft must be stowed properly.

Safety Around Helicopters

Safety Around Helicopters Every type of helicopter has different features. These differences must be learned to avoid damaging the helicopter or injuring the technician. When approaching a helicopter while the blades are turning, adhere to the following guidelines to ensure safety.

• Observe the rotor head and blades to see if they are level. This allows maximum clearance when approaching the helicopter.

• Approach the helicopter in view of the pilot.

• Never approach a helicopter carrying anything with a vertical height that the blades could hit. This could cause blade damage and injury to the individual.

• Never approach a single-rotor helicopter from the rear. The tail rotor is invisible when operating.

• Never go from one side of the helicopter to the other by going around the tail. Always go around the nose of the helicopter.

When securing the rotor on helicopters with elastomeric

bearings, check the maintenance manual for the proper method. Using the wrong method could damage the bearing.

Fire Safety

Fire Safety Performing maintenance on aircraft and their components requires the use of electrical tools that can produce sparks, heat-producing tools and equipment, flammable and explosive liquids, and gases. As a result, a high potential exists for fire to occur. Measures must be taken to prevent a fire from occurring and to have a plan for extinguishing it.

The key to fire safety is knowledge of what causes a fire, how to prevent it, and how to put it out. This knowledge must be instilled in each technician, emphasized by their supervisors through sound safety programs, and occasionally practiced. Airport or other local fire departments can normally be called upon to assist in training personnel and helping to establish fire safety programs for the hangar, shops, and flight line.

Fire Protection

Fire Protection

Requirements for Fire to Occur Three things are required for a fire. Remove any one of these things and the fire extinguishes:

1. Fuel—combines with oxygen in the presence of heat, releasing more heat. As a result, it reduces itself to other chemical compounds.

2. Heat—accelerates the combining of oxygen with fuel, in turn releasing more heat.

Requirements for Fire to Occur

3. Oxygen—the element that combines chemically with another substance through the process of oxidation. Rapid oxidation, accompanied by a noticeable release of heat and light, is called combustion or burning. [Figure 1-3]

Classification of Fires For commercial purposes, the National Fire Protection Association (NFPA) has classified fires into three basic types: Class A, Class B, and Class C.

Figure 1-3: picture of page 27Figure 1-3 · page 27
Picture of the page from the copy saved here

Classification of Fires

1. Class A fires involve ordinary combustible materials, such as wood, cloth, paper, upholstery materials, and so forth.

2. Class B fires involve flammable petroleum products or other flammable or combustible liquids, greases, solvents, paints, and so forth.

3. Class C fires involve energized electrical wiring and equipment.

A fourth class of fire, the Class D fire, involves flammable metal. Class D fires are not commercially considered by the NFPA to be a basic type of fire since they are caused

by a Class A, B, or C fire. Usually Class D fires involve magnesium in the shop, or in aircraft wheels and brakes, or are the result of improper welding operations.

Any one of these fires can occur during maintenance on or around, or operations involving aircraft. There is a particular type of extinguisher that is most effective for each type of fire.

Types and Operation of Shop and Flight Line Fire Extinguishers

Types and Operation of Shop and Flight Line Fire Extinguishers Water extinguishers are the best type to use on Class A fires. Water has two effects on fire. It deprives fire of oxygen and cools the material being burned.

Since most petroleum products float on water, water-type fire extinguishers are not recommended for Class B fires. Extreme caution must be used when fighting electrical fires (Class C) with water-type extinguishers. All electrical power must be removed or shut off to the burning area. Additionally, residual electricity in capacitors, coils, and so forth must be considered to prevent severe injury or possibly death from electrical shock.

Never use water-type fire extinguishers on Class D fires. The cooling effect of water causes an explosive expansion of the metal, because metals burn at extremely high temperatures.

Water fire extinguishers are operated in a variety of ways. Some are hand pumped, while others are pressurized. The pressurized types of extinguishers may have a gas charge stored in the container with the water, or it may contain a “soda-acid” container where acid is spilled into a container of soda inside the extinguisher. The chemical reaction of the soda and the acid causes pressure to build inside the fire extinguisher, forcing the water out.

Carbon dioxide (CO2) extinguishers are used for Class A, B, and C fires, extinguishing the fire by depriving it of oxygen. [Figure 1-4] Additionally, like water-type extinguishers, CO2 cools the burning material. Never use CO2 on Class D fires. As with water extinguishers, the cooling effect of CO2 on the hot metal can cause explosive expansion of the metal.

Figure 1-4: picture of page 27Figure 1-4 · page 27
Picture of the page from the copy saved here

When using CO2 fire extinguishers, all parts of the extinguisher can become extremely cold, and remain so for a short time after operation. Wear protective equipment or take other precautions to prevent cold injury, such as frostbite. Extreme caution must be used when operating CO2 fire extinguishers in closed or confined areas. Not only can the fire be deprived of oxygen, but so too can the operator.

CO2 fire extinguishers generally use the self-expelling method of operation. This means that the CO2 has sufficient pressure at normal operating pressure to expel itself. This

It takes three things to start a fire: OXYGEN, HEAT, FUEL

Oxygen

Friction (heat) Fuel

Figure 1-3. Three elements of fire.

Figure 1-4. Carbon dioxide fire extinguisher.

pressure is held inside the container by some type of seal or frangible disk that is broken or punctured by a firing mechanism, usually a pin. This means that once the seal or disk is broken, pressure in the container is released and the fire extinguisher is spent, requiring replacement. [Figure 1-5]

Figure 1-5: picture of page 28Figure 1-5 · page 28
Picture of the page from the copy saved here

Halogenated hydrocarbon extinguishers are most effective on Class B and C fires. They can be used on Class A and D fires, but they are less effective. Halogenated hydrocarbon, commonly called Freon™ by the industry, are numbered according to chemical formulas with Halon™ numbers.

Carbon tetrachloride (Halon 104), chemical formula CCl4, has an Underwriters Laboratory (UL) toxicity rating of 3. As such, it is extremely toxic. [Figure 1-6] Hydrochloric acid vapor, chlorine, and phosgene gas are produced whenever carbon tetrachloride is used on ordinary fires. The amount of phosgene gas is increased whenever carbon tetrachloride is brought in direct contact with hot metal, certain chemicals, or continuing electrical arcs. It is not approved for any fire extinguishing use. Old containers of Halon 104 found in or around shops or hangars should be disposed of in accordance with Environmental Protection Agency (EPA) regulations and local laws and ordinances.

Figure 1-6: picture of page 28Figure 1-6 · page 28
Picture of the page from the copy saved here

Methyl bromide (Halon 1001), chemical formula CH3Br, is a liquefied gas with a UL toxicity rating of 2. It is very toxic and corrosive to aluminum alloys, magnesium, and zinc. Halon 1001 is not recommended for aircraft use. Chlorobromomethane (Halon 1011), chemical formula CH2ClBr, is a liquefied gas with a UL toxicity rating of 3. Like methyl bromide, Halon 1011 is not recommended for aircraft use. Dibromodifluoromethane (Halon 1202), chemical formula CBr2F2, has a UL toxicity rating of 4. Halon 1202 is not recommended for aircraft use.

Bromochlorodifluoromethane (Halon 1211), chemical formula CBrClF2, is a liquefied gas with a UL toxicity rating of 5. It is colorless, noncorrosive, and evaporates rapidly leaving no residue. It does not freeze or cause cold burns and does not harm fabrics, metals, or other materials it contacts. Halon 1211

acts rapidly on fires by producing a heavy blanketing mist that eliminates oxygen from the fire source. More importantly, it interferes chemically with the combustion process of the fire. Furthermore, it has outstanding properties in preventing reflash after the fire has been extinguished.

Bromotrifluoromethane (Halon 1301), chemical formula CF3Br, is also a liquefied gas and has a UL toxicity rating of 6. It has all the characteristics of Halon 1211. The significant difference between the two is Halon 1211 forms a spray similar to CO2, while Halon 1301 has a vapor spray that is more difficult to direct.

Note: The EPA has restricted Halon to its 1986 production level due to its effect on the ozone layer.

Dry powder extinguishers, while effective on Class B and C fires, are best for use on Class D fires. The method of operation of dry powder fire extinguishers varies from gas cartridge charges, stored pressure within the container that forces the powder charge out of the container, to scooping pails or buckets of the powder from large containers or barrels to toss on the fire.

Extinguishing Materials

Classes of Fire

Self-Generating

Self-Expelling

Cartridge of

N2 Cylinder

Stored

Pressure

Pump

Hand

A B C D

Water and antifreeze

Soda-acid (water)

Wetting agent

Foam

Loaded stream

Multipurpose dry chemical

Carbon dioxide

Dry chemical

Bromotrifluoromethane — Halon 1301

Bromochlorodifluoromethane — Halon 1211

Dry powder (metal fires)

X

X

X

X

X

X+

X

X

X

X

X

X

X

X

X

X

X

X X

X

X

X X

X+

X

X+

X

X

X

X

X

X

X

X

X

X

X

+ Smaller sizes of these extinguishers are not recognized for use on these classes of fire.

Group Definition Examples

Gases or vapors in concentrations up to 20% by volume, for durations of exposure of up to approximately 2 hours, do not appear to produce injury.

Gases or vapors much less toxic than Group 4, but more toxic than Group 6.

Gases or vapors in concentrations of the order of 2 to 2 ½%, for durations of exposure of up to approximately 2 hours are lethal or produce serious injury.

Gases or vapors in concentrations of the order of 2 to 2 ½%, for durations of exposure of the order of 1 hour are lethal or produce serious injury.

Gases or vapors in concentrations of approximately ½ to 1%, for durations of exposure of up to approximately ½ hour are lethal or produce serious injury.

6 (Least toxic)

5a

4

3

2

Carbon dioxide

Dibromodifluormethane (Halon 1202)

Bromochloromethane (Halon 1011)

Bromotrifluoromethane (Halon 1301)

Carbon tetrachloride (Halon 104)

Methyl bromide (Halon 1001)

Figure 1-5. Extinguisher operation and methods of expelling.

Figure 1-6. Toxicity table.

Dry powder is not recommended for aircraft use, except on metal fires, as a fire extinguisher. The leftover chemical residues and dust often make cleanup difficult and can damage electronic or other delicate equipment.

Inspection of Fire Extinguishers

Inspection of Fire Extinguishers Fire extinguishers need to be checked periodically utilizing a checklist. If a checklist is unavailable, check the following as a minimum:

• Proper location of appropriate extinguisher

• Safety seals unbroken

• All external dirt and rust removed

• Gauge or indicator in operable range

• Proper weight

• No nozzle obstruction

• No obvious damage

Airport or other local fire departments can usually help in preparing or providing extinguisher checklists. In addition, these fire departments can be helpful in answering questions

and assisting in obtaining repairs to or replacement of fire extinguishers.

Identifying Fire Extinguishers

Identifying Fire Extinguishers Fire extinguishers are marked to indicate suitability for a particular class of fire. The markings on Figure 1-7 must be placed on the fire extinguisher and in a conspicuous place in the vicinity of the fire extinguisher. When the location is marked, however, take extreme care to ensure that the fire extinguisher kept at that location is in fact the type depicted by the marking. In other words, if a location is marked for a Class B fire extinguisher, ensure that the fire extinguisher in that location is in fact suitable for Class B fires.

Markings must be applied by decalcomanias (decals), painting, or similar methods. They are to be legible and as durable as necessary for the location. For example, markings used outside need to be more durable than those in the hangar or office spaces.

Figure 1-7: picture of page 30Figure 1-7 · page 30
Picture of the page from the copy saved here

When markings are applied to the extinguisher, they are placed on the front of the shell, if one is installed, above or below the extinguisher nameplate. Markings must be large enough and in a form that is easily seen and identifiable by the average person with average eyesight at a distance of at least 3 feet.

When markings are applied to wall panels, and so forth, in the vicinity of extinguishers, they must be large enough and in a form that is easily seen and identifiable by the average person with average eyesight at a distance of at least 25 feet. [Figure 1-8]

Figure 1-8: picture of page 30Figure 1-8 · page 30
Picture of the page from the copy saved here

Using Fire Extinguishers

Using Fire Extinguishers When using a fire extinguisher, ensure the correct type is used for the fire. Most extinguishers have a pin to pull that allows the handle to activate the agent. Stand back 8 feet and aim at the base of the fire or flames. Squeeze the lever and sweep side to side until the fire is extinguished.

Tie-Down Procedures

Tie-Down Procedures

Preparation of Aircraft Aircraft are to be tied down after each flight to prevent damage from sudden storms. The direction that aircraft are to be parked and tied down is determined by prevailing or forecast wind direction.

Aircraft are to be headed into the wind, depending on the locations of the parking area’s fixed tie-down points. Spacing of tie-downs need to allow for ample wingtip clearance. [Figure 1-9] After the aircraft is properly located, lock the nosewheel or the tail wheel in the fore-and-aft position.

Figure 1-9: picture of page 30Figure 1-9 · page 30
Picture of the page from the copy saved here

Securing Light Aircraft

Tie-Down Procedures for Land Planes Securing Light Aircraft Light aircraft are most often secured with ropes tied only at the aircraft tie-down rings provided for securing purposes. Rope is never to be tied to a lift strut, since this practice can bend a strut if the rope slips to a point where there is no slack. Since manila rope shrinks when wet, about 1 inch (1") of slack needs to be provided for movement. Too much slack, however, allows the aircraft to jerk against the ropes. Tight tie-down ropes put inverted flight stresses on the aircraft and many are not designed to take such loads.

A tie-down rope holds no better than the knot. Anti-slip knots, such as the bowline, are quickly tied and are easy to untie. [Figure 1-10] Aircraft not equipped with tie-down fittings must be secured in accordance with the manufacturer’s instructions. Ropes are to be tied to outer ends of struts on high-wing monoplanes and suitable rings provided where structural conditions permit, if the manufacturer has not already provided them.

Figure 1-10: picture of page 31Figure 1-10 · page 31
Picture of the page from the copy saved here

Securing Heavy Aircraft

Securing Heavy Aircraft The normal tie-down procedure for heavy aircraft can be accomplished with rope or cable tie-down. The number of tie-downs are governed by anticipated weather conditions.

Most heavy aircraft are equipped with surface control locks that are engaged or installed when the aircraft is secured. Since the method of locking controls vary on different types of aircraft, check the manufacturer’s instructions for proper installation or engaging procedures. If high winds are anticipated, control surface battens can also be installed to prevent damage. Figure 1-11 illustrates four common tiedown points on heavy aircraft.

The normal tie-down procedure for heavy aircraft includes the following:

1. Head aircraft into prevailing wind whenever possible.

2. Install control locks, all covers, and guards.

3. Chock all wheels fore and aft. [Figure 1-12]

4. Attach tie-down reels to aircraft tie-down loops, tiedown anchors, or tie-down stakes. Use tie-down stakes for temporary tie-down only. If tie-down reels are not available, 1⁄4" wire cable or 11⁄2" manila line may be used.

Figure 1-11: picture of page 31Figure 1-11 · page 31
Picture of the page from the copy saved here

Tie-Down Procedures for Seaplanes

Tie-Down Procedures for Seaplanes Seaplanes can be moored to a buoy, weather permitting, or tied to a dock. Weather causes wave action, and waves cause the seaplane to bob and roll. This bobbing and rolling while

COMBUSTIBLES

ORDINARY

CAPABILITY

LIQUIDS

FLAMMABLE

EQUIPMENT

ELECTRICAL

COMBUSTIBLES

ORDINARY

LIQUIDS

FLAMMABLE

EQUIPMENT

ELECTRICAL

EQUIPMENT

ELECTRICAL

LIQUIDS

FLAMMABLE

METALS

COMBUSTIBLE

1. Water

2. Carbon Dioxide, Dry Chemical Bromochlorodifluoromethane, and Bromotrifluoromethane

3. Multipurpose Dry Chemical

4. Multipurpose Dry Chemical (Insufficient Agent for ‘A’ Rating)

5. Dry Powder

COMBUSTIBLES

ORDINARY

LIQUIDS

FLAMMABLE

EQUIPMENT

ELECTRICAL

METALS

COMBUSTIBLE

6'

2'

3'

3'

6'

10'

+ Major axis

3'

3' Figure 1-7. Typical extinguisher markings.

Figure 1-8. Identification of fire extinguisher type location.

Figure 1-9. Diagram of tiedown dimensions.

Tie-Down Procedures for Ski Planes

Tie-Down Procedures for Ski Planes Ski planes are tied down, if the securing means are available, in the same manner as land planes. Ski-equipped airplanes can be secured on ice or in snow by using a device called a dead-man. A dead-man is any item at hand, such as a piece of pipe, log, and so forth, that a rope is attached to and buried in a snow or ice trench. Using caution to keep the free end of the rope dry and unfrozen, snow is packed in the trench. If available, pour water into the trench; when it is frozen, tie down the aircraft with the free end of the rope.

tied to a dock can cause damage.

When warning of an impending storm is received and it is not possible to fly the aircraft out of the storm area, some compartments of the seaplane can be flooded, partially sinking the aircraft. Tie down the aircraft securely to anchors. Seaplanes tied down on land have been saved from high-wind damage by filling the floats with water in addition to tying the aircraft down in the usual manner. During heavy weather, if possible, remove the seaplane from the water and tie down in the same manner as a land plane. If this is not possible, the seaplane could be anchored in a sheltered area away from the wind and waves.

Tying a Bowline Knot A

Tying a Square Knot B

Over

This one must be under Up through and around back

Back down through

Under

Under

Over

Figure 1-10. Knots commonly used for aircraft tie-down.

Aft fuselage tiedown ring

Underside of wing

tiedown loop Main gear wheel tiedown loop

Nose landing gear tiedown loop

Figure 1-11. Common tie-down points.

length of time the aircraft is expected to remain on the ground, and location and characteristics of the aircraft. Wheel chocks, control locks, rope tie-downs, mooring covers, tip socks, tie-

down assemblies, parking brakes, and rotor brakes are used

Operators of ski-equipped aircraft sometimes pack soft snow around the skis, pour water on the snow, and permit the skis to freeze to the ice. This, in addition to the usual tie-down procedures, aids in preventing damage from windstorms. Caution must be used when moving an aircraft that has been secured in this manner to ensure that a ski is not still frozen to the ground. Otherwise, damage to the aircraft or skis can occur.

Tie-Down Procedures for Helicopters

Tie-Down Procedures for Helicopters Helicopters, like other aircraft are secured to prevent structural damage that can occur from high-velocity surface winds. Helicopters are to be secured in hangars, when possible. If not, they must be tied down securely. Helicopters that are tied down can usually sustain winds up to approximately 65 mph. If at all possible, helicopters are evacuated to a safe area if tornadoes or hurricanes are anticipated. For added protection, helicopters can be moved to a clear area so that they are not damaged by flying objects or falling limbs from surrounding trees.

If high winds are anticipated with the helicopter parked in the open, tie down the main rotor blades. Detailed instructions for securing and mooring each type of helicopter can be found in the applicable maintenance manual. [Figure 1-13] Methods of securing helicopters vary with weather conditions, the

Figure 1-12. Wheels chocked fore and aft.

to secure helicopters. Typical mooring procedures are as follows:

Figure 1-13: picture of page 33Figure 1-13 · page 33
Picture of the page from the copy saved here

1. Face the helicopter in the direction that the highest forecast wind or gusts are anticipated.

2. Spot the helicopter slightly more than one rotor span distance from other aircraft.

3. Place wheel chocks ahead of and behind all wheels (where applicable). On helicopters equipped with skids, retract the ground handling wheels, lower the helicopter to rest on the skids, and install wheel position lock pins or remove the ground-handling wheels. Secure ground-handling wheels inside the aircraft or inside the hangar or storage buildings. Do not leave them unsecured on the flight line.

4. Align the blades and install tie-down assemblies as prescribed by the helicopter manufacturer. [Figure 1-14] Tie straps snugly without strain, and during wet weather, provide some slack to avoid the possibility of the straps shrinking, causing undue stress on the aircraft and/or its rotor system(s).

5. Fasten the tie-down ropes or cables to the forward and aft landing gear cross tubes and secure to ground stakes or tie-down rings.

Figure 1-14: picture of page 33Figure 1-14 · page 33
Picture of the page from the copy saved here

Procedures for Securing Weight-Shift-Control

Procedures for Securing Weight-Shift-Control There are many types of weight-shift-controlled aircraft— engine powered and non-powered. These types of aircraft are very susceptible to wind damage. The wings can be secured in a similar manner as a conventional aircraft in light winds. In high winds, the mast can be disconnected from the wing and the wing placed close to the ground and secured. This type of aircraft can also be partially disassembled or moved into a hangar for protection.

Procedures for Securing Powered Parachutes

Procedures for Securing Powered Parachutes When securing powered parachutes, pack the parachute in a bag to prevent the chute from filling with air from the wind and dragging the seat and engine. The engine and seat can also be secured if needed.

Ground Movement of Aircraft

Engine Starting and Operation The following instructions cover the starting procedures for reciprocating, turboprop, turbofan, and APU. These procedures are presented only as a general guide for familiarization with typical procedures and methods. Detailed instructions for starting a specific type of engine can be found in the manufacturer’s instruction book.

Engine Starting and Operation

Before starting an aircraft engine:

1. Position the aircraft to head into the prevailing wind to ensure adequate airflow over the engine for cooling purposes.

2. Make sure that no property damage or personal injury occurs from the propeller blast or jet exhaust.

3. If external electrical power is used for starting, ensure that it can be removed safely, and it is sufficient for the total starting sequence.

4. During any and all starting procedures, a “fireguard” equipped with a suitable fire extinguisher shall be stationed in an appropriate place. A fireguard is someone familiar with aircraft starting procedures. The fire extinguisher should be a CO2 extinguisher of at least 5-pound capacity. The appropriate place is adjacent to the outboard side of the engine, in view of the pilot, and also where they can observe the engine/ aircraft for indication of starting problems.

5. If the aircraft is turbine-engine powered, the area in front of the jet inlet must be kept clear of personnel, property, and/or debris (FOD).

6. These “before starting” procedures apply to all aircraft powerplants.

7. Follow manufacturer’s checklists for start procedures and shutdown procedures.

Reciprocating Engines

Reciprocating Engines The following procedures are typical of those used to start reciprocating engines. There are, however, wide variations in the procedures for the many reciprocating engines. Do not attempt to use the methods presented here for actually starting an engine. Instead, always refer to the procedures contained in the applicable manufacturer’s instructions. Reciprocating engines are capable of starting in fairly low temperatures

Align the blades

Figure 1-14. Securing helicopter blades and fuselage.

Figure 1-13. Example of mooring of a helicopter.

without the use of engine heating or oil dilution, depending on the grade of oil used.

The various covers (wing, tail, flight deck, wheel, and so forth) protecting the aircraft must be removed before attempting to turn the engine. Use external sources of electrical power when starting engines equipped with electric starters, if possible or needed. This eliminates an excessive burden on the aircraft battery. Leave all unnecessary electrical equipment off until the generators are furnishing electrical power to the aircraft power bus.

Before starting a radial engine that has been shut down for more than 30 minutes, check the ignition switch for off. Turn the propeller three or four complete revolutions by hand to detect a hydraulic lock, if one is present. Any liquid present in a cylinder is indicated by the abnormal effort required to rotate the propeller or by the propeller stopping abruptly during rotation. Never use force to turn the propeller when a hydraulic lock is detected. Sufficient force can be exerted on the crankshaft to bend or break a connecting rod if a lock is present.

To eliminate a lock, remove either the front or rear spark plug from the lower cylinders and pull the propeller through. Never attempt to clear the hydraulic lock by pulling the propeller through in the direction opposite to normal rotation. This tends to inject the liquid from the cylinder into the intake pipe. The liquid is drawn back into the cylinder with the possibility of complete or partial lock occurring on the subsequent start.

To start the engine, proceed as follows:

1. Turn the auxiliary fuel pump on, if the aircraft is so equipped.

2. Place the mixture control to the position recommended for the engine and carburetor combination being started. As a general rule, put the mixture control in the “idle cut-off” position for fuel injection and in the

“full rich” position for float-type carburetors. Many light aircraft are equipped with a mixture control pull rod that has no detent intermediate positions. When such controls are pushed in flush with the instrument panel, the mixture is set in the “full rich” position. Conversely, when the control rod is pulled all the way out, the carburetor is in the “idle cut-off” or “full lean” position. The operator can select unmarked intermediate positions between these two extremes to achieve any desired mixture setting.

3. Open the throttle to a position that provides 1,000 to 1,200 rpm (approximately 1⁄8" to 1⁄2" from the “closed” position).

4. Leave the pre-heat or alternate air (carburetor air) control in the “cold” position to prevent damage and fire in case of backfire. These auxiliary heating devices are used after the engine warms up. They improve fuel vaporization, prevent fouling of the spark plugs, ice formation, and eliminate icing in the induction system.

5. Move the primer switch to “on” intermittently (press to prime by pushing in on the ignition switch during the starting cycle), or prime with one to three strokes of priming pump, depending on how the aircraft is equipped. The colder the weather, the more priming is needed.

6. Energize the starter and after the propeller has made at least two complete revolutions, turn the ignition switch on. On engines equipped with an induction vibrator (shower of sparks, magneto incorporates a retard breaker assembly), turn the switch to the “both” position and energize the starter by turning the switch to the “start” position. After the engine starts, release the starter switch to the “both” position. When starting an engine that uses an impulse coupling magneto, turn the ignition switch to the “left” position. Place the start switch to the “start” position. When the engine starts, release the start switch. Do not crank the engine continuously with the starter for more than 1 minute. Allow a 3- to 5-minute period for cooling the starter (starter duty cycle) between successive attempts. Otherwise, the starter may be burned out due to overheating.

7. After the engine is operating smoothly, move the mixture control to the “full rich” position if started in the “idle cutoff” position. Carbureted engines are already in the rich mixture position. Check for oil pressure.

8. Instruments for monitoring the engine during operation include a tachometer for rpm, manifold pressure gauge, oil pressure gauge, oil temperature gauge, cylinder head temperature gauge, exhaust gas

temperature gauge, and fuel flow gauge.

Hand Cranking Engines

Hand Cranking Engines If the aircraft has no self-starter, start the engine by turning the propeller by hand (hand propping the propeller). The person who is turning the propeller calls: “Fuel on, switch off, throttle closed, brakes on.” The person operating the engine checks these items and repeats the phrase. The switch and throttle must not be touched again until the person swinging the prop calls “contact.” The operator repeats “contact” and then turns on the switch. Never turn on the switch and then call “contact.”

A few simple precautions help to avoid accidents when hand propping the engine. While touching a propeller, always assume that the ignition is on. The switches that control the magnetos operate on the principle of short-circuiting the current to turn the ignition off. If the switch is faulty, it can be in the “off” position and still permit current to flow in the magneto primary circuit. This condition could allow the engine to start when the switch is off.

Be sure the ground is firm. Slippery grass, mud, grease, or loose gravel can lead to a fall into or under the propeller. Never allow any portion of your body to get in the way of the propeller. This applies even when the engine is not being cranked.

Stand close enough to the propeller to be able to step away as it is pulled down. Stepping away after cranking is a safeguard in case the brakes fail. Do not stand in a position that requires leaning toward the propeller to reach it. This throws the body off balance and could cause a fall into the blades when the engine starts.

In swinging the prop, always move the blade downward by pushing with the palms of the hands. Do not grip the blade with the fingers curled over the edge, since “kickback” may break them or draw your body in the blade path. Excessive throttle opening after the engine has fired is the principal cause of backfiring during starting. Gradual opening of the throttle, while the engine is cold, reduces the potential for backfiring. Slow, smooth movement of the throttle assures correct engine operation.

Avoid over priming the engine before it is turned over by the starter. This can result in fires, scored or scuffed cylinders and pistons, or engine failures due to hydraulic lock. If the engine is inadvertently flooded or over primed, turn the ignition switch off and move the throttle to the “full open” position. To rid the engine of the excess fuel, turn it over by hand or by the starter. If excessive force is needed to turn over the engine, stop immediately. Do not force rotation of the engine. If in doubt, remove the lower cylinder spark plugs.

Immediately after the engine starts, check the oil pressure indicator. If oil pressure does not show within 30 seconds, stop the engine and determine the trouble. If oil pressure is indicated, adjust the throttle to the aircraft manufacturer’s specified rpm for engine warm up. Warm up rpm is usually between 1,000 to 1,300 rpm.

Most aircraft reciprocating engines are air cooled and depend on the forward speed of the aircraft to maintain proper cooling. Therefore, particular care is necessary when operating these engines on the ground. During all ground running, operate the engine with the propeller in full low pitch and headed into the wind with the cowling installed to provide the best degree of engine cooling. Closely monitor the engine instruments at all times. Do not close the cowl flaps for engine warm-up, they need to be in the open position while operating on the ground. When warming up the engine, ensure that personnel, ground equipment that may be damaged, or other aircraft are not in the propeller wash.

Extinguishing Engine Fires

Extinguishing Engine Fires In all cases, a fireguard should stand by with a CO2 fire extinguisher while the aircraft engine is being started. This is a necessary precaution against fire during the starting procedure. The fireguard must be familiar with the induction system of the engine so that in case of fire, they can direct the CO2 into the air intake of the engine to extinguish it. A fire could also occur in the exhaust system of the engine from liquid fuel being ignited in the cylinder and expelled during the normal rotation of the engine.

If an engine fire develops during the starting procedure, the operator should continue cranking to start the engine and extinguish the fire. If the engine does not start and the fire continues to burn, discontinue the start attempt. The fireguard then extinguishes the fire using the available equipment. The fireguard must observe all safety practices at all times while standing by during the starting procedure.

Turboprop Engines

Turboprop Engines The starting of any turbine engine consists of three steps that must be carried out in the correct sequence. The starter turns the main compressor to provide airflow though the engine. At the correct speed that provides enough airflow, the igniters are turned on and provide a hot spark to light the fuel that is engaged next. As the engine accelerates, it reaches a selfsustaining speed and the starter is disengaged.

The various covers protecting the aircraft must be removed. Carefully inspect the engine exhaust areas for the presence of fuel or oil. Make a close visual inspection of all accessible parts of the engines and engine controls, followed by an inspection of all nacelle areas to determine that all inspection

and access plates are secured. Check sumps for water. Inspect air inlet areas for general condition and foreign material. Check the compressor for free rotation, when the installation permits, by reaching in and turning the blades by hand.

The following procedures are typical of those used to start turboprop engines. There are, however, wide variations in the procedures applicable to the many turboprop engines. Therefore, do not attempt to use these procedures in the actual starting of a turboprop engine. These procedures are presented only as a general guide for familiarization with typical procedures and methods. For starting of all turboprop engines, refer to the detailed procedures contained in the applicable manufacturer’s instructions or their approved equivalent.

Turboprop engines are usually fixed turbine or free turbine. The propeller is connected to the engine directly in a fixed turbine, resulting in the propeller being turned as the engine starts. This provides extra drag that must be overcome during starting. If the propeller is not at the “start” position, difficulty may be encountered in making a start due to high loads. The propeller is in flat pitch at shut down and subsequently in flat pitch during start because of this.

The free turbine engine has no mechanical connection between the gas generator and the power turbine that is connected to the propeller. In this type of engine, the propeller remains in the feather position during starting and only turns as the gas generator accelerates.

Instrumentation for turbine engines varies according to the type of turbine engine. Turboprop engines use the normal instruments—oil pressure, oil temperature, inter-turbine temperature (ITT), and fuel flow. They also use instruments to measure gas generator speed, propeller speed, and torque produced by the propeller. [Figure 1-15] A typical turboprop uses a set of engine controls, such as power levelers (throttle), propeller levers, and condition levers. [Figure 1-16]

Figure 1-15: picture of page 37Figure 1-15 · page 37
Picture of the page from the copy saved here

The first step in starting a turbine engine is to provide an adequate source of power for the starter. On smaller turbine engines, the starter is an electric motor that turns the engine through electrical power. Larger engines need a much more powerful starter. Electric motors would be limited by current flow and weight. Air turbine starters were developed that were lighter and produced sufficient power to turn the engine at the correct speed for starting. When an air turbine starter is used, the starting air supply may be obtained from an APU onboard the aircraft, an external source (ground air cart), or an engine cross-bleed operation. In some limited cases, a low-pressure, large-volume tank can provide the air for starting an engine. Many smaller turboprop engines are started using the starter/generator, that is both the engine

starter and the generator.

While starting an engine, always observe the following:

• Always observe the starter duty cycle. Otherwise, the starter can overheat and be damaged.

• Assure that there is enough air pressure or electrical capacity before attempting a start.

• Do not perform a ground start if turbine inlet temperature (residual temperature) is above that specified by the manufacturer.

• Provide fuel under low pressure to the engine’s fuel pump.

Turboprop Starting Procedures

Turboprop Starting Procedures To start an engine on the ground, perform the following operations:

1. Turn the aircraft boost pumps on.

2. Make sure that the power lever is in the “start” position.

3. Place the start switch in the “start” position. This starts the engine turning.

4. Place the ignition switch on. (On some engines, the ignition is activated by moving the fuel lever.)

5. The fuel is now turned on. This is accomplished by moving the condition lever to the “on” position.

6. Monitor the engine lights of the exhaust temperature. If it exceeds the limits, shut the engine down.

7. Check the oil pressure and temperature.

8. After the engine reaches a self-sustaining speed, the starter is disengaged.

9. The engine continues to accelerate up to idle.

10. Maintain the power lever at the “start” position until the specified minimum oil temperature is reached.

11. Disconnect the ground power supply, if used.

If any of the following conditions occur during the starting sequence, turn off the fuel and ignition switch, discontinue the start immediately, make an investigation, and record the findings.

• Turbine inlet temperature exceeds the specified maximum. Record the observed peak temperature.

• Acceleration time from start of propeller rotation to stabilized rpm exceeds the specified time.

• There is no oil pressure indication at 5,000 rpm for either the reduction gear or the power unit.

• Torching (visible burning in the exhaust nozzle).

• The engine fails to ignite by 4,500 rpm or maximum motoring rpm.

• Abnormal vibration is noted or compressor surge occurs (indicated by backfiring).

• Fire warning bell rings. (This may be due to either an engine fire or overheat.)

Continue reading ↓ 120 of 2706 passages shown