FAA-H-8083-17A Changed Pages Parachute Rigger Handbook (Change 1): Changed Pages for Replacement
This document is historical. It may have been replaced. Check the official source before relying on it.
Text read by OCR from a scanned file (31 of 81 pages). Check the original, as some words may be misread.
Change I
r Handbook
Parachute Rigger
U.S.Department of Transportation
Federal Aviation Administration
veedle Single needle
10 11 12
son Harne
Zigzag medium
aght duty medium duty drop feed needle feed Sit 31-15 111W151 111W1S Consew 292R N/A 206RB-4 Juki DLN-415 LU-563 Brother B-791 Mitsubishi DB-130 DY-340-12 LU2-400 Pfaff
112W116 333RB-1 LH-515
LT2-220
Bar tack maching duty du
17W15 68 or 69 class 199R-2A N/A
LZ-780-11 138 3334
Change 1 (December 2015)
Parachute Rigger Handbook
U.S. Department of Transportation FEDERAL AVIATION ADMINISTRATION
Flight Standards Service
August 2015
iv
vii
Change 1 (December 2015)
This is an updated version of FAA-H-8083-17A, Parachute Rigger Handbook, dated August 2015. This version contains error corrections, revised graphics, and updated performance standards. All pages containing changes are marked with the change number and change date in the page footer. The original pagination has been maintained so that the revised pages may be replaced in lieu of repurchasing or reprinting the entire handbook. The changes made in this version are as follows:
• Updated Table of Contents page numbers (page ix).
• Replaced Figure 2-12 (page 2-8) with version from previous version of the handbook (FAA-H-8083-17, Figure 2-10).
• Revised the third sentence in the second paragraph in the left column of page 2-14: changed “3⁄8"” to “1⁄2".”
• Revised the caption for Figure 3-17 (page 3-7): changed “Tape” to “Webbing.”
• Revised the caption for Figure 3-18 (page 3-7): changed “Tape” to “Webbing.”
• Revised the last sentence in the first paragraph in the right column of page 7-2: changed “FAA-licensed” to “FAAcertificated.”
• Revised the third bullet under Square Canopy – Rib Repair in the right column of page 7-25: added “—mains and reserves; FAA Senior Parachute Rigger—mains.”
• Revised Figure G at the bottom of page 7-82: removed “+2"” after “X = Required length.”
• Revised Appendix A Table of Contents (page A-1): revised titles of new documents and updated page numbers.
• Revised Appendix A: replaced PIA TS-100—Standardized Nomenclature for Ram-Air Parachutes with latest version (pages A-3 – A-10).
• Revised Appendix A: replaced SAE AS 8015B—Minimum Performance Standards for Parachute Assemblies and Components with Personnel PIA TS 135—Performance Standards for Personnel Parachute Assemblies and Components (pages A-26 – A-43)
• Revised Appendix A: updated page numbering for all documents (pages A3 – A-65).
Record of Changes
viii
ix Change 1 (December 2015)
Preface … iii
Acknowledgments … v
Record of Changes … vii
Table of Contents … ix
Chapter 1 Introduction to Parachute Rigging … 1-1 Regulations and Human Factors … 1-1 Parachute Rigger Certificates … 1-2
Eligibility and Requirements … 1-2 Earning a Parachute Rigger Certificate … 1-2
Testing … 1-3 Alternate Means of Qualifying for a Parachute Rigger Certificate … 1-3 Retesting … 1-3 Responsibilities of a Certificated Parachute Rigger … 1-5
Facilities and Tools … 1-5 Performance Standards … 1-5 Currency Requirements … 1-6 Record Keeping … 1-7 Sealing the Parachute … 1-8 Regulatory Compliance … 1-8
14 CFR part 1—Definitions … 1-8 14 CFR part 21, subpart O—Technical Standard Orders (TSO) … 1-8 14 CFR part 39—Airworthiness Directives (ADs) … 1-8 14 CFR part 91—General Operating and Flight Rules … 1-9 14 CFR part 105, subpart C—Parachute Equipment and Packing … 1-9 Rigging Ethics … 1-9
Certification Specifications … 1-9 Pilot Versus Parachute Size … 1-9 Parachute Service Life … 1-9 Chapter Summary … 1-10
Chapter 2 Design and Construction … 2-1 Introduction … 2-1 Parachute Design and Construction … 2-2
Component Parts … 2-2
Main Parachute Canopy … 2-2 Reserve Parachute Canopy … 2-2 Emergency Parachute Canopy … 2-2 Harness/Container … 2-2
Pilot Chutes and Bridles for the Main and Reserve Parachutes … 2-2 Ripcords or Equivalent Devices for the Main and Reserve Parachutes … 2-3 Deployment Devices for the Main and Reserve Parachutes … 2-3 Main Parachute Release Mechanism and Associated Handles or Static Lines … 2-3 Risers and Associated Steering Toggles … 2-3 TSO Standards … 2-4 Canopy Design … 2-5
Nomenclature … 2-5 Construction Concepts and Techniques … 2-5 Operational Theory … 2-6 Materials … 2-6 Damage … 2-6 Containers … 2-6 Configuration … 2-7 Harness Design … 2-9 Bridles and Deployment Devices … 2-11
Deployment Types … 2-12
Type 1: Canopy First Deployment … 2-12 Type 2: Two-Stow Diaper or Half Diaper … 2-12 Type 3: Ascuitto or Piglet-Style Flat Diaper … 2-13 Type 4: Handbury or Preserve Full Diaper … 2-13 Type 5: Free Bag … 2-13 Type 6: Sleeves … 2-13 Bridles … 2-15 Pilot Chutes … 2-17
Spring-Loaded Pilot Chutes … 2-17 Hand Deploy Pilot Chutes … 2-17 Automatic Activation Devices (AADs) and Reserve Static Lines (RSLs) … 2-18
Automatic Activation Devices … 2-18 Operation … 2-19 Reserve Static Line (RSL) Systems … 2-21 RSL Designs … 2-21
Table of Contents
x Change 1 (December 2015)
Main Riser Attachment … 2-22 Ripcord Cable Routing … 2-23 RSL Lanyard and Container Mount … 2-23 Joint Efficiency … 2-24 Chapter Summary … 2-25
Chapter 3 Materials … 3-1 Introduction … 3-1 Specifications … 3-2 Fabrics … 3-2 Webbing and Tapes … 3-3
Webbing Selection … 3-4 Cords, Lines, and Threads … 3-8 Hardware … 3-12 Plastics and Synthetics … 3-20 Fasteners … 3-21 Housings … 3-22 Ripcords, Cables, and Swages … 3-24 Miscellaneous … 3-26 Chapter Summary … 3-26
Chapter 4 Operations … 4-1 Introduction … 4-1 Sport Parachute Main Packing Techniques … 4-2 Deployment and Inflation Characteristics … 4-8
Main Pilot Chute … 4-9 Bridle Length … 4-10 Rubber Bands … 4-10 Assembly of the Main Canopy To The Harness and Container … 4-11 Assembly of Components and Compatibility … 4-13
Reserve Bag Extraction Force … 4-14 TSO Certification and Placard Limitations … 4-14 Harness Strength … 4-14 Volume … 4-16 Deployment Type … 4-16 Chapter Summary … 4-17
Chapter 5 Inspection and Packing … 5-1 Introduction … 5-1 Identification … 5-2 Inspection … 5-2
Component Compatibility … 5-4 Round Canopies and Pilot Emergency Systems … 5-7 Straightening the Canopy … 5-7 Damage Identification … 5-8 Pilot Chute and Bridle … 5-8 Reserve Canopy … 5-9
Suspension Lines and Connector Links … 5-10 Harness … 5-11 Container … 5-12 Ripcord … 5-12 Airing and Drying … 5-13 Ram-Air Reserves and Sport Piggyback Systems....5-13
Pilot Chute and Free Bag/Bridle … 5-13 Ram-Air Reserve Canopy … 5-13 Canopy Assembly and Line Continuity … 5-14 Inspection … 5-16 Harness … 5-17 Container … 5-17 Ripcord … 5-18 Rigging and Repairs … 5-19 Packing … 5-19
Round Canopy into a Pilot Emergency Parachute System … 5-20
Layout … 5-20 Pleating the Canopy … 5-21 Fold the Skirt … 5-22 Closing the Diaper and Stowing the Lines … 5-23 Skirt or Diaper Placement … 5-24 Accordion Folding the Canopy … 5-25 Closing the Container … 5-25 Ripcord Pull Force … 5-27 Sealing the Parachute … 5-27 Ram-Air Reserve into a Sport Piggyback System....5-28
Assembling the Reserve System … 5-28 Ram-Air Reserve into a Two-Pin Piggyback … 5-38 Documentation … 5-39 Chapter Summary … 5-42
Chapter 6 Hand Tools, Sewing Machines, and the Parachute Loft … 6-1 Introduction … 6-1 Hand Tools … 6-2
Hand Tools Description … 6-2 Sewing Machines … 6-14
Identification and Nomenclature … 6-16 Sewing Theory … 6-18
Needles … 6-20 Operation … 6-21 Installing the Needle and Threading the Machine....6-21 Machine Maintenance … 6-23 Sewing Machine Attachments … 6-24 The Parachute Loft … 6-24
Packing and Inspection Area … 6-25 Work Area Including Layout Tables and Sewing Machines … 6-26
xi Change 1 (December 2015)
Harness Table and Machines … 6-27 Cutting Table … 6-27 Metal Working Area … 6-27 Office Area … 6-27 Materials Storage Area … 6-28 Chapter Summary … 6-28
Chapter 7 Repairs, Alterations, and Manufacture … 7-1 Introduction … 7-1 Inspection Process … 7-2 Major or Minor Repairs … 7-8 Contamination Conditions … 7-8
Acid Contamination … 7-10
Action … 7-10 Salt Water Contamination … 7-10
Action … 7-10 Removal of Perspiration … 7-10 Removal of Fresh Water … 7-10 Removal of Mildew … 7-10 Removal of Petroleum Products … 7-10 Removal of Bloodstains … 7-10 Removal of Soil … 7-10 Drying a Parachute … 7-11 Cleaning the Parachute … 7-11
Hand Washing (If Absolutely Necessary) … 7-11 Approved Data … 7-11
Types of Approved Data … 7-12 Repair Techniques … 7-12 Section 1, Canopy and Lines … 7-13
Detailed Information on Square Canopy Repairs … 7-14 Materials … 7-14 Seam Restitching … 7-15
Procedure … 7-15 Inspection … 7-15 Canopy Ripstop Tape Repair … 7-16
Procedure … 7-16 Inspection … 7-17 Round and Square Canopy—Basic Patch Repair … 7-17
Procedure … 7-18 Round Canopy—Panel Replacement … 7-21
Procedure … 7-21 Inspection … 7-22 Square Canopy—Partial Panel Replacement … 7-22
Procedure … 7-22 Inspection … 7-25 Square Canopy—Rib Repair … 7-25
Procedure … 7-25 Inspection … 7-28
Square Canopy—Pilot Chute Attachment Point Repair … 7-28
Procedure … 7-28 Inspection … 7-30 Round Canopy—Non-continuous Line Replacement … 7-30
Procedure … 7-30 Inspection … 7-31 Square Canopy—Main Line Replacement … 7-31
Procedure … 7-31 Inspection … 7-32 Square Canopy—Control Line Replacement … 7-33
Procedure … 7-33 Continuous Line Method … 7-34 Non-continuous Line Method … 7-34
Inspection … 7-35 Square Canopy—Crossport Repair … 7-36
Procedure … 7-36 Inspection … 7-36 Square Canopy—Trim Check and Re-trim … 7-37
Procedure … 7-37 Inspection … 7-38 Section 2, Container … 7-38
Container Fabric Panel Repair … 7-38
Procedure … 7-39 Binding Tape Repair or Splice … 7-39 Hidden Patches … 7-40 Overlay Patches … 7-40 Single-Side Fabric Patches … 7-41 Inspection … 7-42 Container Grommet Replacement … 7-42
Procedure … 7-42 Material Repair and Grommet Replacement … 7-43
Inspection … 7-43 Container Velcro® Replacement … 7-43
Procedure … 7-43 Inspection … 7-44 Container Plastic Stiffener Replacement … 7-44
Procedure … 7-44 Main Container Side Flap Replacement … 7-46
Procedure … 7-46 Inspection … 7-48 Bottom of Container (BOC) Pocket Replacement....7-48
Procedure … 7-48 Inspection … 7-49 Ring Release Housing Replacement … 7-49
Procedure … 7-49 Inspection … 7-50
xii Change 1 (December 2015)
Section 3, Harness and Risers … 7-51
Chest Strap Replacement … 7-51
Procedure … 7-51 Inspection … 7-54 Lower Leg Strap Shortening … 7-54
Procedure … 7-54 Inspection … 7-55 Ripcord Pocket Velcro® Replacement … 7-55
Procedure … 7-55 Inspection … 7-56 Articulated Upper Leg Hardware Replacement … 7-56
Procedure … 7-56 Inspection … 7-56 Standard Harness Main Lift Web Replacement … 7-57
Background … 7-58 Procedure … 7-59 Inspection … 7-62 Main Riser 3-Ring Locking Loop Replacement … 7-62
Procedure … 7-63 Main Riser Steering Toggle Velcro® Replacement..7-64
Procedure … 7-64 Inspection … 7-65 Section 4, Accessory Components … 7-65
Reserve Pilot Chute Repair—Mesh, Tackings, and Bad Grommet … 7-65
Procedure … 7-65 Inspection … 7-66 Inspection … 7-67 Reserve Free Bag Repair—Grommet Pullout … 7-67
Procedure … 7-67 Inspection … 7-68 Main Pilot Chute Repair—Top Canopy Reinforcing … 7-68
Procedure … 7-68 Inspection … 7-69 Main Pilot Chute Collapsible Bridle Replacement...7-69
Procedure … 7-69 Inspection … 7-71 Main Deployment Bag Repair—Closing Flap Grommet Pullout … 7-72
Procedure … 7-72 Inspection … 7-73 Section 5, Alterations … 7-73
Articulated Harness Main Lift Web (MLW) Resizing … 7-73
Procedure … 7-74 Leg Pad Resizing … 7-74
Procedure … 7-75 Inspection … 7-77
Automatic Activation Device (AAD) Installation....7-77
Procedure … 7-77 Built-In Channel Modification Configuration … 7-78 Adhesive Channel Installation … 7-78 Cutter Channel and Elastic Installation … 7-79 Inspection … 7-80 Section 6, Manufacturing … 7-80
Main and Reserve Closing Loop Manufacture … 7-80
Procedure … 7-80 Inspection … 7-82 Main Deployment Bag … 7-82
Procedure … 7-83 Inspection … 7-84 Bottom of Container (BOC) Pocket … 7-85
Procedure … 7-85 Inspection … 7-86 Section 7, Manufacturing … 7-86
Hand Tacking Techniques … 7-86
Procedure … 7-87 Cleaning and Washing Procedures … 7-89
Background … 7-89 Colorfastness … 7-89
Procedure … 7-89 Chapter Summary … 7-90
Appendix A … A-1
Glossary … G-1
Index … I-1
Figure 2-10. Modern military container.
Figure 2-11. Square reserve hesitator loop configuration.
Figure 2-12. Non-restrictive container corners.
most influential concept in the evolving container design. Cones were replaced by fabric closing loops, and main ripcords and pins were replaced by hand deploy bridles and locking pins. It was no longer necessary to compress the spring-loaded pilot chute inside the container. Thru closing loops were used to compress the pack and make it thinner to conform to the body shape. The use of deployment bags and other devices helped provide shaping to the container. This was true for both square and round canopies.
Figure 2-10 · page 11Picture of the page from the copy saved here
Today, most modern container designs have completely done away with frames and bow stiffeners. This has resulted in smaller, more flexible, more comfortable, and more efficient container designs. Instead of metal stiffeners, nylon plastic is used to reinforce the container flaps for backing the grommets. The nylon is lighter, easier to work with, and cheaper. Many of the modern military designs now follow the design concepts pioneered by the sport industry as they have proven better and more cost effective. Figure 2-10 shows a modern military container.
Modern Design Concepts The containers of today do more than simply enclose the canopy and deployment device. Sport containers in particular need to be designed so that they contribute to the deployment needs of the specific parachute. Piggyback designs have separate requirements for the main and reserve containers.
The reserve container is generally small, tight, and mostly wedge-shaped. Virtually all popular sport systems are designed around the use of a ram-air canopy. The deployment method of choice is a Type 5 deployment bag. In the early days of the ram-air reserve, there were certain container design requirements specified by the manufacturers which are listed below:
1. A hesitator loop configuration secures the bridle and holds the bag in until the reserve pilot chute is deployed and under drag. [Figure 2-11]
2. Nonrestrictive corners to allow the bag to be lifted off by the bridle in the event of a horseshoe-type malfunction. [Figure 2-12]
Figure 2-30. Safety Stow®.
Figure 2-28. Hesitator loops.
Figure 2-29. Para-Flite O-rings.
Figure 2-27. Tail pocket.
Securing the Deployment Device With all deployment methods, it is necessary to properly fold or stow the canopy and secure the deployment device with the lines. The early parachutes utilized hesitator loops to secure the lines. [Figure 2-28] This method is still used today in many military systems.
Figure 2-11 · page 11Picture of the page from the copy saved here
In modern designs that utilize types 1 through 4 and 6, the preferred method of locking the deployment device is rubber bands. The specification for standard rubber bands is MIL-R-1832. Type 1 are made of natural rubber and are
1⁄2" × 2". These were designed for use with the thicker Type III nylon lines such as on the 28' C-9 canopy. Many of the newer lightweight, round canopies use smaller diameter and fewer lines. Consequently, the standard rubber bands do not work well. Some manufacturers supply smaller, 1¼" diameter rubber bands to be used with their canopies. It is extremely important to utilize the correct size rubber bands.
With the introduction of the free bag system in 1977, Para- Flite, Inc., used a BUNA-N “O” ring to secure the locking stows. [Figure 2-29] During testing of the free bag system, they found inconsistent holding and breaking strengths of rubber bands. They wanted the locking stows to release at a consistent force to prevent bag lock. The “O” rings provided this. A couple of years later, the “O” rings were upgraded to a thicker diameter model. In 1983, Para-Flite, Inc. replaced
the “O” rings with the Safety Stow®. The Safety Stow® is a continuous loop of elastic shock cord that runs through a webbing channel and through two grommets to secure the first two locking stows. [Figure 2-30] In the event of any restriction on the locking stow, as the loop stretches, it allows first one side to release and then the opposite side.
Figure 2-29 · page 12Picture of the page from the copy saved here
It is important to maintain the rubber bands or Safety Stow®. Rubber bands are susceptible to heat degradation and may dry out. If they break prematurely during use, the parachute may malfunction. Non-mil. specification rubber bands may react to natural brass grommets and may become gummy and sticky, causing the lines to stick to the diaper or bag. Rubber bands should be replaced during routine Inspection and Repack. [Figure 2-31A and B] The BUNA-N “O” rings should be replaced with the Safety Stow®. The Safety Stow® should be inspected for broken stitching or internal rubber strands. [Figure 2-32]
In response to occasional violent openings on ram-air canopies, Parachute Labs (Jump Shack) in 2003 introduced the “speed bag” to eliminate “line dump” (line strip). The lines are retained in rubber bands 25 percent in from the edge of the bag. This balances the mass of the stows between the
Specification:
Strength:
Identification:
Common Use:
Comment:
PIA-W-4088
500 lb
2/2 HB twill, 9/16" width, no color code
Stow band retainer loops on main deployment bags
N/A
Specification:
Strength:
Identification:
Common Use:
Comment:
PIA-W-4088
2,500 lb
2/2 HB twill, 123/32" width, red centerline
Buffer strips, harness attachment straps on Navy containers
N/A
Specification:
Strength:
Identification:
Common Use:
Comment:
PIA-W-4088
1,800 lb
2/2 HB twill, 3" width, some slider edge tapes
Confluence wraps, container reinforcing
Not to be confused with 5038 Ty-4 square weave.
Specification:
Strength:
Identification:
Common Use:
Comment:
PIA-W-4088
6,000 lb
Double plain weave, 123/32" width, 1/16" thick, with yellow tracer thread at each selvage edge
Modern sport harness, risers
Originally intended for cargo netting use; also used in sport harnesses
Figure 3-17. 9⁄16" Type-1 Webbing. Figure 3-19. Type-6 Webbing.
Figure 3-18. 3" Type-4 Webbing.
Figure 3-20. Type-7 Webbing.
Figure 3-17 · page 13Picture of the page from the copy saved here
As stated in Chapter 1 of this handbook, Regulations and Human Factors, it is imperative that riggers be able to distinguish between minor and major repairs. This ensures that riggers do not exceed the limitations of their certificate or endanger the parachute user. The basic rule for repairs is to return the damaged parachute or component to its original airworthy configuration. However, in many instances, the remanufacture of the parachute may not be practical or cost effective. In these cases, there are approved repair techniques riggers can use to return the parachute to service. These techniques form an important part of the rigger’s store of knowledge. To make a decision as to the confirmation for the possible need for repairs, we must first understand the Federal Aviation Administration (FAA) requirement of inspection.
Inspection Process
Chapter 5 of this handbook, Inspection and Packing, addresses the purpose of the 180-day cycle as required by the FAA. This action insures that the approved/certificated parachute assembly meets the standards and conditions for safe return to service; it also become the cornerstone of the maintenance and repair process.
The confirmation of wear or damage is critical in the determination of actions that may be needed as set forth in Title 14 of the Code of Federal Regulations (14 CFR) part 43 and key in the assessment of actions and clarity of the repair that may need to be performed.
As is the character of any device or object, use and physical location conditions (heat, moisture, sand, dirt) over time cause wear to an item and, on occasion, misuse or improper actions during use result in damage. Certain parts or areas of a device incur more wear or damage according to use, action of handling, and contact with other components. Knowledge of this aspect should require increased or location specific consideration during the inspection process.
This recognition possibility of high-wear components or areas does not decrease or eliminate the inspection of any other part of the parachute assembly. It only identifies that the wear or damage probabilities are greater at these locations. These areas are referred to as common wear or damage patterns and apply to both round and square parachutes and parachute assemblies. These types of common wear/damage pattern applies in greater detail to the parachute that is utilized as the main parachute and deployed on each jump in sport use.
The inspection of a reserve canopy after deployment should be very concise and complete. Much care should be taken for a very thorough inspection of the parachute and related components. Parachutes are manufactured in two categories: approved (certificated) and non-approved
(non-certificated). All reserve emergency use parachutes are approved (certificated) and are tested to FAA-required Technical Standard Order (TSO) standards. They are used and maintained by FAA standards (inspection and repaired by FAA-cetificated rigger or the manufacturer) as airframe and powerplant (A&P) mechanics are used.
Non-approved or non-certificated parachutes are generally main parachutes, and related components, which can be packed, used, and repaired outside of FAA maintenance and repair requirements. Rigger inspections and rigger repairs are highly recommended but not required. Inspection of and approved (certificated) parachute calls for inspection of all related components, which are listed below. Related components are parts of the parachute, deployment system, harness, and container system, and any item that has responsibility for containment, deployment, or operation of an approved (certificated) parachute and are a critical part of the assembly. They must be inspected for use the same as the reserve parachute.
• Deployment bag (freebag, safety stow)
• Bridle and pilot chute
• Slider, slider fabric, and grommets
• Rapid links (soft links)
• Rapid link covers (soft link covers)
• All seams and seam fabric
• Suspension lines and line attachments
• Ripcord housing and attachments
• Ripcord assembly
• Upper and lower skins of canopy, all load and non-load bearing ribs, all cross ports
All of these areas can sustain wear or damage during normal use. The event of use at very high speeds can be contributed to the possibility of increased damage from exceeding the maximum speed allowed during deployment.
During inspection of certificated/approved parachutes, it is advisable to map related damage found on a chart which is shown in Figure 7-1. This chart can be used to describe the location of needed repair to a customer, assist in quickly locating the damage, and answer questions that the manufacturer may have relating to possible repair. [Figure 7-1]
If a rigger were to receive a damaged sport main canopy for repair, it would be advantageous to gain as much information as possible as to the cause and situation that created the damage. Inspection of the canopy should be as follows:
11. Check the tension of the new partial panel piece against the edges of the other panels that formed the original seam. They should all be equal. [Figure K]
12. Refold the original seam with the three panel edges and stitch as per the original seam. [Figure L] Overstitch a minimum of 2 inches on each end.
13. If a line attachment has been removed for the repair, the tab must be replaced. Make sure that the line/tab does not have a twist in it. Locate it at the correct location and reattach as per original.
Inspection
• Check the fabric tension of the replaced panel. It should be equal to that in the remainder of the cell.
• Spanwise reinforcing tape should be straight and sewn.
• Seams should be folded correctly and thread tension even along both rows of stitching.
• Line should be attached correctly and have no twists.
Square Canopy—Rib Repair
• Applicable products: square canopies; main and reserve
• Description: Rib repair on a square canopy
• Authorized repairmen: FAA Master Parachute Rigger —mains and reserves; FAA Senior Parachute Rigger—mains
• Materials: E thread; fabric—type and color to match, reinforcing tape—type and color as per original
• Machines: 301 dtraight dtitch—medium duty 7–11 SPI, 1 inch × 42 stitch bar tack, double needle with puller attachment (optional) and SPI to match original • Equipment: Scissors, seam ripper, marking pencil, ruler, pin board, straight pins, and patching square
Procedure Repairing a rib of a square canopy is similar to doing a partial panel repair. The biggest difference comes when the rib is either:
1. A “loaded” rib or one with support tapes for the line attachment points, or 2. A crossport is damaged and needs to be repaired and recut. In this case, the crossport area needs replacement. [Figure A]
Disassembly
1. Determine the extent of the damaged area and unpick the top and bottom seams to access the rib. [Figure B] In most cases, restitching the rib to the top and bottom panels is fairly straightforward. Because of this, opening up the seam for a good distance (18 inches plus either side of the proposed patch) allows easier access and sewing.
2. Pin the damaged rib to the pin board to stabilize the material for marking. Mark out the damaged portion of the panel, following the weave of the fabric.
PIA TS-100—Standardized Nomenclature for Ram-Air Parachutes … A-3
PIA TS-108—Parachute Canopy Fabric Pull Test, Non-Destructive Method … A-16
TSO C23d—Personnel Parachute Assemblies … A-24
PIA TS 135—Performance Standards for Personnel Parachute Assemblies and Components … A-26
TSO C23c—Personnel Parachute Assemblies … A-44
TSO C23b—Parachutes … A-46
TSO C23f—Personnel Parachute Assemblies and Components … A-48
NAS 804—Specification–Parachutes … A-54
Senior Rigger Training Syllabus … A-59
Master Rigger Training Syllabus … A-63
Technical Documents
Appendix A
PIA Technical Standard 100 Parachute Industry Association Publications
March 27, 2015 Standardized Nomenclature for Ram-Air Parachutes Introduction This Technical Standard was adopted by the Parachute Industry Association (PIA) on March 27, 2015. Input concerning revisions and additions should be submitted to: Parachute Industry Association, Inc. Attention: Technical Committee Chair 3833 West Oakton Street Skokie, IL 60076 Telephone: 847-674-9472 Fax: 847-674-9743 Email: [email protected] Definitions Airlock: On a canopy, a valve which permits air flow more easily in one direction, and restricts airflow in the opposite direction. In most case, airlocks are installed in the nose of the canopy to permit air to enter during deployment and flight, and restrict air from flowing out the nose to ensure better pressurization in turbulent air. Angle of
Attack: The angle formed between the flight path and the chord line. The Greek letter alpha (α) is used to denote the angle of attack. See Figure 3.
Trim: The angle formed between the horizontal reference line and the trim line. The Greek letter theta (θ) is used to denote the angle of trim. Used instead of the somewhat analogous aircraft term “angle of incidence.” See Figure 1b. Area,
Airfoil Section: The finished cross sectional area of a given rib (airfoil) section. When ribs are not identical, the specific rib must be identified. Used for calculations of pack volume and internal volume of canopy.
Planform: The product of the average chord times the average span of the canopy. Projected: The area of an inflated canopy as viewed from above, perpendicular to the chord line at the centerline of the parachute. Due to canopy curvature and cell inflation bulging the projected area is always smaller than the planform area. Aspect Ratio: Span2/Area, which for a rectangular planform reduces to Span/Chord.
Page 2 of 8
Attachment Point: A loop of tape, webbing, or the functional equivalent, for attaching something to the surface of the canopy.
Pilot Chute. An attachment point for the pilot chute or pilot chute bridle, including any reinforcement to reduce the effects of abrasion, and also including any additional rib- or canopyreinforcing tapes intended to distribute the load from the pilot chute to the canopy. Suspension Line. An attachment point for a suspension line or control line. Some canopies use extensions of rib-reinforcing or flare-reinforcing load tapes to form line attachment points. See also Flare, Suspension Line Attachment. Cell: The chamber formed by upper and lower surfaces and two adjacent loadbearing ribs. Channel,
Drawstring: A fabric or tape channel that encloses a drawstring, most often found on main canopy sliders. Pilot Chute Reefing: A channel that runs through the center of the canopy, from upper surface to the lower surface, to allow the pilot chute bridle to connect to the slider. Chord: The distance from the farthest forward point to the farthest aft point on an airfoil section. If the canopy airfoil sections are not identical, an average chord may be specified. Airfoil dimensions are assumed to be finished dimensions unless otherwise specified. See also Span, and Line (Design), Chord. Construction,
Chordwise: A construction method in which upper and lower surfaces are assembled from panels which run from front to rear (chordwise) and are joined to the ribs and each other using a variety of sewn seams. The most common type of ram-air parachute construction. Spanwise: A construction method in which the upper and lower surfaces are assembled from panels that run from side to side (spanwise) across the full width of the canopy. Personnel parachutes usually require three or four panels each for the upper and lower surfaces. Crossports: Holes cut in the rib sections to balance the air pressure between adjacent chambers. Drawstring, Slider: A length of tape or line which may be pulled to collapse or remove a slider after deployment. Flare, Suspension Line Attachment: An extension of a load bearing rib used on some canopies to distribute suspension line loads along the lower rib seams. A suspension line attachment flare may be integral with the rib or may be sewn to it. Line (Design),
Chord: A line drawn through the farthest forward point and the farthest aft point on an airfoil section. See Figure 3. Reference, Horizontal: A line drawn at a right angle to the Vertical Reference Line. Usage is equivalent to the practice of using the aircraft longitudinal axis as an aircraft reference line. See Figure 3. Reference, Vertical: A line drawn through the links and the quarter chord point.
Page 3 of 8
Trim: A line drawn through the farthest forward and farthest aft line attachment points (excluding control line attachment points). See Figure 1b. Line (Rigging),
Cascade: A line attached with one end at the canopy and the other end to an intermediate point of an adjacent line. Contrast with Continuous. Continuous: A line attached with one end at the canopy and the other end at the riser of connector link. Contrast with Cascade. Control: A line fastened to the trailing edge of the canopy, used to steer and modulate the forward speed and descent rate of the parachute. Also known as steering or brake line.
Flare: A control line intended primarily for flaring the canopy for landing, but which may also for steering. Also known as Secondary control lines, in which case the remaining control lines are known as Primary control lines. Brake-Toggle: When a control line is constructed in sections, that portion of the line between the toggle and the deployment set eye (“cat-eye”). Lower: When a control line is constructed in sections, that portion of the line between the deployment set eye and the upper portion. Upper: When a control line is constructed in sections, that portion of the line between the canopy and where it converges with other lines attached to the canopy.
Identification System for:
Suspension lines: lettered “A,” “B,” “C,” . . . from front to rear along each load-bearing seam. Numbered from outboard to inboard (outboard lines numbered “1”; see Figure 2a ) or inboard to outboard (lines on center load-bearing seams numbered “1”; see Figure 2b). Control lines: numbered by rib seam, including non-load-bearing ribs, from outboard to inboard. See Figures 2a and 2b. Suspension: One of the lines that carries the load from the canopy surface to the risers. Control lines are usually not considered suspension lines. Pilot Chute Controlled Reefing (PCR): A parachute reefing system that uses the drag of the pilot chute to modulate the opening rate of the canopy. Planform: The overall shape of the wing as viewed from above, perpendicular to the chord line. Quarter Chord Point: a point on the chord line one quarter of the distance from the nose to the tail of an airfoil. Removable Deployment System (RDS): A slider variation that permits the slider to be removed and stowed separately after deployment. “Full RDS” is a further variation that also permits the pilot chute, bridle, and deployment bag to be removed and stowed after deployment. Rib: A section of fabric installed between the upper and lower surfaces of a canopy. Used to establish the airfoil shaped of the canopy. Rib numbering systems (for example, from outboard to inboard, or from inboard to outboard) vary from manufacturer to manufacturer.
Page 4 of 8
Rib, crossbrace: A rib or partial rib installed at an angle other than a 90° angle to the upper and lower surfaces of a canopy. Rib, loadbearing: A rib to which suspension lines are attached, installed at a 90° angle to the upper and lower surfaces of a canopy. Rib, non-loadbearing: A rib without attached suspension lines, installed at a 90° angle to the upper and lower surfaces of a canopy. Rib, stabilizer: A stabilizer-end rib assembly with line attachments along the lower edge. Rigging,
Crown: A suspension line length pattern in which all “A” lines are the same length across the span of the canopy, all “B” lines are the same length across the span of the canopy, and similarly all “C” and “D” lines, etc. Flat: A suspension line length pattern in which the lines in the center of the canopy are shorter than the lines farther outboard. In flight, the center part of the airfoil is flatter and creates more vertical lift than a crown-rigged canopy, which generates lift along the radius of the spanwise arc. Setting,
Deployment: The position of the trailing edge when the control lines are pulled down to their deployment position. Full-Flight: The position of the trailing edge when the control lines are fully extended. Slider: A parachute reefing device usually consisting of a rectangular section of canopy cloth reinforced on the edges with lightweight webbing or tape, and with a large grommet or D-ring installed at each corner. Sliders may have fabric removed from the rectangular section or may have fabric edge extensions installed to change opening characteristics. Slider variations include:
• Domed, with a planform similar to a flat rectangular slider, but with fabric pleated along the edges. • Split, capable of being disassembled into halves after deployment . • Spider, made of two lengths of webbing sewn in an “X,” and usually used with pilot chute controlled reefing. See Pilot Chute Controlled Reefing (PCR). • Removable. See Removable Deployment System. Slider Bumper: A small device, typically made from vinyl/silicon tubing, Type-4 tape, or Type-12 webbing, installed at the lower end of the suspension lines to prevent damage to the slider grommets caused by the slider contacting the connector links. Slider Stop: A small piece of rigid material (metal, plastic, phenolic, etc.) normally covered in tape or light webbing, installed on the lower edge of a stabilizer panels to prevent a slider grommet from riding up over the stabilizer material and damaging the stabilizers or the slider. Slider Stop Chafing Pad: A tape or fabric reinforcement installed on a stabilizer at a slider stop to reduce wear from abrasion. Soft link: A connector link constructed primarily of fabric or tape. Span: The distance from one side of a canopy to the opposite side. Measurements taken at various distances aft of the nose will yield different results, Measurements taken across the upper surface will typically be longer than those taken across the lower. An average span, or separate leading and trailing edge dimensions, may be specified. Airfoil dimensions are assumed to be finished dimensions unless otherwise specified. See also Chord.
Page 5 of 8
Stabilizer: A fabric panel installed at the end of a canopy, intended primarily to reduce wingtip vortices (much as an end plate on an aircraft wing), and to provide some directional stability. Some stabilizer designs are ram-air pressurized for additional rigidity. Tapes, Reinforcement: A tape installed in the canopy to provide additional strength or dimensional stability. Tapes are identified by location.
Cross Tapes: A reinforcing tape that runs spanwise on the upper or lower surface to distribute loads through the canopy. With chordwise construction, a cross tape typically runs from a line attachment point to laterally adjacent line attachment point, although some may run from a suspension line attachment point diagonally to a control line attachment point. With spanwise construction, a cross tape may be rolled into a seam joining spanwise panels. Leading Edge Tape: A tape applied to or rolled into the leading edge of a upper or lower panel. May be continuous across the span of the canopy. Line Attachment Reinforcement Tape: A tape sewn chordwise into a seam at a line attachment point. Load Tape: A tape applied to a rib section and used to distribute the load from a line attachment to the canopy. When applied in a “V” may also be known as a “V-tape.” In some canopies, load tapes may extend through the lower seam to become line attachment points. Rib Leading Edge Tape: A tape applied to or rolled into the leading edge of a rib section.
Trailing Edge Tape: A tape applied to or rolled into the trailing edge seam. Usually continuous across the span of the canopy. Toggle, Control: A grip attached to the end of the control line to allow the user an adequate handhold on the line. Most commonly consists of a tape/webbing loop or a hard plastic dowel. Typically supplied as part of the container assembly. Trim: The arrangement of differential line lengths to produce a desired trim angle and anhedral. See also Angle of Trim. See Figures 1a and 1b. Vent, Lower Surface: An opening in the lower surface to provide an alternate path for pressurization during deployment (“inflation vent”) or depressurization during flight (“accuracy vent”).
All lines measured pulled to equal tension (5 -35 pounds typical, varies by manufacturer and line type) parallel to the "A" line, and secured to the same connector link or peg.
When measuring control line trim, secure the deployment setting eye to the connector link or peg.
A-ine
"A" line loop as an initial reference. 1. Use the top of the 2. Measure each subsequent line differential between the top of its loop and the top of the "A" line loop. "B," "C," and "D" lines shown, typical. 3. Measure the control line differential at the deployment setting.
Figure 1a. Measuring line length trim.
quarter chord point
trim line point: rear-most line
reference line horizontal trim line trim line point: attachment
"A"-line attachment
trim angle (θ): the angle
between the trim line and the horizontal reference line reference line vertical
links
Figure 1b. Measuring trim angle.
A-8 Change 1 (December 2015)
A1 A2 I A3
B1 B2 B3 1
1 1 C2 C3 I
C1 1
1 D2 D3
A4
1
B4
C4
D4
A5
B5
C5
D5
A5 1 A4 1 A3 A2 I I 1 A1 I
B5 B4 B3 B2 B1 1 1 C5 C4 C3 C2 I I C1 1 D5 D4 D3 D2 1
1
1 I
Upper Steering Lines
Primmary Lower
1 1
)(FIare)
1 1 7 6 5 4 3
Sedary
Steering Lines
Brake-Toggle
A4 A3 A5 1
A2
A1
Figure 2b. Suspension and control line designation, Method 1. 9-cell canopy shown, 7-cell canopy similar. Control line arrangement varies.
A1 1 A2 A3 A4 A5
I
1 1 B5 B4 B3 1 1 1
I C4 1 C3 I 1 C5
1 D4 D3 I 1
Upper Steering Lines
Priary Lower
B2 I
C2 I
D2 1 i
(FIare)
B1
C1
D1
i 1
B1 B2 B3 B4 B5
C1 C2 C3 I C4 1 1 C5
D1 D2 I D3 D4 1 1 1 I 1 7 6 5 4 3
Secdary
Steering Lines
Brake-Toggle
Figure 2a. Suspension and control line designation, Method 2. 9-cell canopy shown, 7-cell canopy similar. Control line arrangement varies.
Page 8 of 8
Figure 3. Angle of attack.
Figure 1.
Slider
Lower control line
Upper control line
Line set 1
Line set 4
Cross tapes
Full cell 1
Half cell 6R
Half cell 2L
Full cell 1
Risers Control toggle
Note: In this view “B” lines are cascaded to “A” lines “D” lines are cascaded to “C” lines
Note: All numbering/lettering precedence is left to right and front to rear (relative to direction of flight).
“A” suspension
line length
“B” line
“A” line
“C” line
“D” line
Crossports
Spanwise construction panels shown
Spanwise seam
Stabilizer panel
Trailing edge tape (rolled inside seam)
Trailing edge
Upper leading edge tape
Lower leading edge tape
Leading edge
Loaded ribs
Non-loaded ribs
Load tapes
8 7 7 6 6 6 5
4 4
1 2 3 4
3
3
2
2
1
1 2 3
1
Direction of flight
SPAN
CHORD
Figure 3 · page 25Picture of the page from the copy saved here
Figure 2.
4
1 2 3 Measurements are trim dimensions.
Measurement is used to specify full flight and deployment brake setting relative to “A” line length.
Note: “A” line length +1 = “B” line length “A” line length +1+2 = “C” line length “A” line length +1+2+3 = “D” line length “A” line length +4 = control line length for full-flight setting “A” line length +4 = control line length for deployment brake settings
1
2
3
4
“D” line “C” line “B” line
Airfoil section
Control lines
“A” line length
Note: In this view, suspension lines are not cascaded.
FF
DB
Loaded Rib with Directly Attached Suspension Lines Showing
Suspension Line Measurements and Trim Dimensions
Loaded Rib Using Flares for Suspension Line Attachments
Note: Trim and rigging information is the same as shown in Figure 3A.
Flares
Lower surface
Upper surface
Figure 3B.
Figure 3A.
Half Cell Chordwise Construction
Lower surface panels
Loaded ribs
Typical
Non-loaded ribs
Upper surface panels
Section view from front
Full Cell Chordwise Construction “I” Beam
Lower surface panels
Loaded ribs
Typical
Typical
Typical
Typical
Figure 2 · page 27Picture of the page from the copy saved here
Non-loaded ribs
Upper surface panels
Section view from front
Full Cell Construction Interlocking “T” Beam
Lower surface
panels
Loaded ribs
Typical Typical Typical
Typical
Non-loaded ribs
Upper surface panels
Section view from front
Figure 4A.
Spanwise Construction
Lower surface
panels
Loaded ribs
Typical Typical
Non-loaded ribs
Upper surface panels
Section view from front
Figure 4B.
Figure 4C. Figure 4D.
25% Chord point–usually assumed as aerodynamic center
Confluence point of connector lines
LEGEND
Plumb line Reference line Chord line Trim line
Horizon
Flight path
Chord Line
90°
Ø + 90°
Figure 5.
PIA-TS-108.1 15 January 2010
Superseding
PIA-TS-108 12 December 1992
PIA Technical Standard
Parachute Canopy Fabric Pull Test Non-Destructive Method
Figure 4A · page 29Picture of the page from the copy saved here
Disclaimer: Parachute canopy manufacturers may have pull test requirements that differ in methods, procedures, and loads applied. Test procedures specified by the canopy manufacturer takes precedence over the test procedures described in this document. The person performing the pull tests must determine if the canopy manufacturer has a specific method of pull testing their canopy fabric.
Background: The purpose of this test method is to provide a simple, standardized, nondestructive method of verifying the strength of parachute canopy fabric. This test method may be used when no other procedure is specified by the manufacturer. Although this test is intended to be non-destructive, caution should be exercised as this test could damage the fabric, if the fabric is not positioned correctly or is not secured tightly. It may also affect the fabric permeability.
This method is designed to replace the old "Riggers' Thumb Test", first devised in response to the "canopy acid-mesh" discovery in the mid-1980's. It is now the accepted method for all parachutes requiring canopy fabric strength tests. Reasons for testing may include: Manufacturer’s Service Bulletins (SBs), Airworthiness Directives (AD’s), aging material, chemical contamination, UV exposure or discoloration of a suspicious origin, such as grease.
Tools required and possible sources are as follows:
2 ea. Locking Fabric Clamps Figure 1
Para-Gear Equipment Co. 800-323-0437 (P/N S7989) 3839 W. Oakton St. www.para-gear.com Skokie, IL 60076-3438
Aerostar International, Inc. 605-331-3500 (P/N 51406M) 1814 N. www.aerostar.com Sioux Falls, SD 57117-5057
Ink, Marking (for parachutes and other textile items) A-A-59211 (21Jul/98) Supersedes MIL-I-6903C (5Mar/68)
American Writing Ink Co. 781-762-0026 33 Endicott St. Norwood, MA 02062
Page 1 of 8
PIA-TS-108.1
Strata Blue P/N 7510-00-286-5362 Available in 1 pint container Orange-Yellow P/N 7510-00-634-6583 Available in 1 pint container
Hitt Marking Devices, Inc. 714-979-1405 3231 W. MacArthur Blvd. 800-969-6699 (toll free) Santa Ana, CA 92704 www.hittmarking.com
Sharpie Pen- black
1 ea. Calibrated Spring Scale, 50 lb. (23 kg.) minimum capacity
This scale should be calibrated at least once a year to an accuracy of +/- 3 lbs. It should be identified with a serial number and written verification of calibration must be kept on file. An adhesive label (or similar) should be affixed to the scale showing the date calibrated and the date next calibration is due. If the scale is damaged in any manner, such as dropping, it must be pulled from service and tagged as unserviceable until its recalibration.
Test Procedures: The following procedures do not take precedence over a manufacturer’s test procedures for their products. Before testing make sure you have the manufacturer’s most current test procedures.
A minimum of 2 areas should be tested on a canopy, but not less than 2 pull tests on each separate color (1 in the warp direction and 1 in the fill direction). When testing look for areas of contamination and/or discoloration. If possible remain approximately 6 inches (150mm) from any seam.
Proceed as follows:
NOTE: Steps 1 and 2 apply to cases involving acid-mesh pull testing.
1. Locate the mesh vents in the canopy and determine the fabric areas which are in contact with the mesh when the canopy is packed. These areas are shown as the diagonally shaded lines in typical tri-vent canopies (see FIGURE 2).
2. Perform one 40 lb. (18 kg.) pull test on each panel of material that comes in contact with the mesh when the canopy is packed. Alternate tests from the warp to fill direction on the panels. This could be as few as four tests or as many as twelve tests on some bias constructed canopies.
CAUTION: Never attach fabric clamps or perform pull tests on the mesh covered areas of any canopy. Extensive damage will result.
NOTE: Steps 3 through 6 apply to all pull tests (not just acid-mesh).
3. The area to be tested must be visibly marked for future reference. Refer to FIGURE 3 for examples of how to mark the parachute to be tested.
4. After the marking ink has dried, attach the locking fabric clamps to the ripstop fabric as shown in FIGURE 4. The distance between the clamps should be 3 inches (76.2mm) plus or minus ¼
Page 2 of 8
PIA-TS-108.1
inch (6.35mm) and the clamps must be aligned so that the ripstop pattern is parallel (not on bias) to the edge of the jaws. Lock the clamps VERY SECURELY. This will prevent slippage and possible damage to the fabric.
NOTE: If the area to be tested is too small to allow 3 inches (76.2mm) plus or minus ¼ inch (6.35mm) between the jaws of the fabric clamps (such as the apex area of a round canopy), the distance between the jaws may be reduced to 2 inches (50.8mm) plus or minus ¼ inch (6.35mm).
5. Secure one clamp to the packing table or other object which will allow a sufficient load to be applied without movement of the fabric clamp. Attach the spring scale hook to the other fabric clamp and apply the load very smoothly and steadily. Hold the load for 3 seconds.
6. Record test results on the tested areas in contrasting ink as shown in FIGURE 5. Information should include the following:
• The amount of loading pulled to in pounds or kilograms • The date tested • The word PASS or FAIL • The name and certificate number of the individual performing the test.
After completing the tests record the information in your rigger logbook and on the packing data card.
(THIS SPACE LEFT INTENTIONALLY BLANK)
Page 3 of 8
PIA-TS-108.1
Fabric clamp (rubber padded/square jaw)
FIGURE 1
NOTE: Use only approved fabric clamps. Improvised or homemade clamps may increase the chances of damaging the area to be tested.
Page 4 of 8
PIA-TS-108.1
Below are diagrams of typical tri-vent modifications.
NOTE: Diagonally shaded areas show examples of fabric that comes in contact with mesh or may contact mesh.
FIGURE 2
Page 5 of 8
PIA-TS-108.1
LB/KG PULL TEST:
DATE:
RIGGER’S NAME AND CERTIFICATE NUMBER
RIGGER’S NAME AND CERTIFICATE NUMBER
NOTE: This method uses either the corners of the box (above) or
the dots (below) as guides for the fabric clamps.
LB/KG PULL TEST:
DATE:
RIGGER’S NAME AND CERTIFICATE NUMBER
Examples of canopy markings
FIGURE 3
NOTE: Use only a rubber stamp and approved ink or a black Sharpie™pen to mark the areas to be tested. Do not use a ballpoint pen, pencils or similar items to mark the test area. This could result in damaging the fabric being tested.
Page 6 of 8
PIA-TS-108.1
Indicator Dots*
(4 Each Test)
Direction
of Load
Clamp 1” Jaw
1”
3”
Ripstop pattern parallel to edge of clamp jaw
Clamp
Jaw
Direction
of Load
Clamp Jaws
3”
Parachute Fabric
How to attach clamps
FIGURE 4
Page 7 of 8
PIA-TS-108.1
40 LB PULL TEST: PASSED
40 LB PULL TEST: PASSED
DATE: 14 JUN 2009
MASTER RIGGER: JOE RIGGER 1234567
Example of completed test
FIGURE 5
Department of Transportation Federal Aviation Administration
Aircraft Certification Service
Washington, DC
Date: 6/1/94
Technical Standard Order
MASTER RIGGER: JOE RIGGER 1234567
Subject: TSO-C23d, PERSONNEL PARACHUTE ASSEMBLIES a. Applicability. (1) Minimum Performance Standards. This technical standard order (TSO) prescribes the minimum performance standard that personnel parachute assemblies must meet in order to be identified with the applicable TSO marking. New models of personnel parachute assemblies that are to be so identified and that are manufactured on or after the date of this TSO must meet the standards set forth in Society of Automotive Engineers, Inc. (SAE) Aerospace Standard (AS) Document No. AS 8015B, “Minimum Performance Standards for Parachute Assemblies and Components, Personnel,” dated July 7, 1992. b. Marking. Each personnel parachute assembly or separate sub-assembly must be marked in accordance with 14 CFR part 21, section 21.607(d) and paragraph 4.2 of SAE AS 8015B. This marking requirement applies to any previously approved major component/subassembly used in this TSO. c. Data Requirements. (1) In addition to the requirement in part 21, section 21.605, the manufacturer shall furnish the manager of the Aircraft Certification Office (ACO), FAA having geographical purview of the manufacturer’s facilities, one copy each of the following technical data: (i) A complete description of the personnel parachute assemblies, including detail drawings, material identification and specifications. (ii) Operating instructions and limitations, to include donning, retention, adjustment, and deployment. (iii) Installation instructions and limitations. (iv) A report of the tests conducted in accordance with SAE AS 8015B for qualification and approval of personnel parachute assemblies.
DISTRIBUTION: ZVS-326; A-W(IR)-3; A-X(CD)-4; A-FFS-7, 8(LTD); A-X(FS)-3;
AFS-600 (2 cys); A-FAC-0(MAX)
TSO-C23d 6/1/94
Page 2
(v) Detailed maintenance instructions, including specific guidance on the limits of wear and damage permissible to webbing material that would warrant replacement. (vi) The quality control inspection and functional test specification to be used to ensure each production article complies with this TSO, as required by part 21, section 21.605(a)(3) and part 21, section 21.143(a)(3). (2) The manufacturer must furnish to the user of the article one copy of the data and information specified in paragraphs c(l)(ii) and c(l)(v). This data and information is necessary for proper installation and use and for continued airworthiness of the product or article.
“The conditions and test required for TSO approval of this article are minimum performance standards. It is the responsibility of those desiring to install the article either on or within a specific type or class of aircraft to determine that the aircraft installation conditions are within the TSO standards. The article may be installed only if further evaluation by the applicant (user/installer) documents an acceptable installation and is approved by the Administrator.” d. Availability of Referenced Documents. (1) Copies of SAE AS 8015B may be purchased from the Society of Automotive Engineers, Inc., Department 331, 400 Commonwealth Drive, Warrendale, PA 15096. (2) Federal Aviation Regulations, part 21, subpart O, may be purchased from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-9325. (3) Advisory Circular 20- 110, “Index of Aviation Technical Standard Orders,” may be obtained from the U.S. Department of Transportation, General Services Section, M-443.2, Washington, DC 20590. /S/ John K. McGrath Manager, Aircraft Engineering Division Aircraft Certification Service
PIA TS 135
PIA TS 135
Parachute Industry Association (PIA)
TECHNICAL STANDARD 135
PERFORMANCE STANDARDS FOR PERSONNEL PARACHUTE ASSEMBLIES AND COMPONENTS
1. SCOPE:
This document defines the performance standards for personnel parachute assemblies (and components thereof) to be carried in aircraft for emergency use by aircrew and those reserve parachutes worn by parachutists for intentional jumping.
This document covers three types of personnel carrying parachute assemblies and the operating limitations for each:
1.1 PARACHUTE TYPES:
1.1.1 Single harness reserve parachute assembly.
1.1.2 Single harness emergency parachute assembly.
1.1.3 Dual harness reserve parachute assembly.
1.2 MAXIMUM OPERATING LIMITS, GENERAL:
1.2.1 A single harness parachute assembly (or components thereof) may be certified for any maximum operating weight and for any maximum pack opening speed equal to or greater than 150 KTAS (277.8 km/h).
1.2.2 A dual harness reserve parachute assembly (or components thereof) may be certified for any maximum operating weight greater than 500 Ib (227.3 kg) (with 250 Ib (113.6 kg) in each harness) and any maximum pack opening speed equal to or greater than 175 KTAS (324.1 km/h). Note that the maximum operating weight need not be the same for each harness.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 1 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior wrtten permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committe, 3833 West Oakton Street, Skokie, L 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in mumbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-26 Change 1 (December 2015)
PIA TS 135
1.3 LIST OF TECHNICAL STANDARDS, TABLES AND FIGURES:
Figure 1 Multiplier Factors for Structural Overload Testing Figure 2 Functional Direct Drop Tests Required per 4.3.8.1 Table 1 Data Marking Requirements Table 2 Human Factors and Actuation Force Tests – Primary Actuation Device/Ripcord Table 3 Performance Test Requirements Table 4 Performance Test Requirements for Component Qualification
2. DEFINITIONS AND GENERAL REQUIREMENTS
2.1 GENERAL DEFINITIONS: For the purposes of this document, the following definitions are used: a. “Administrator” — The FAA Administrator or equivalent chief executive of the cognizant agency and/or his designated subordinate personnel and/or designated subordinate organization acting on his behalf and with his authority in the matter concerned. b. "Airspeed, Calibrated" (KCAS) means the indicated airspeed of an aircraft, corrected for position and instrument error. Calibrated airspeed is equal to true airspeed in standard atmosphere at sea level. C. "Airspeed, Equivalent" (KEAS) means the calibrated airspeed of an aircraft corrected for adiabatic compressible flow for the particular altitude. Equivalent airspeed is equal to calibrated airspeed in standard atmosphere at sea level. d. "Airspeed, Indicated" (KIAS) means the speed of an aircraft as shown on its pitot static airspeed indicator calibrated to reflect standard atmosphere adiabatic compressible flow at sea level uncorrected for airspeed system errors. e.
“Airspeed, True” (KTAS) – means the airspeed relative to undisturbed air. True airspeed is equal to equivalent airspeed multiplied by (ρo/ρ)1⁄2 where ρo is the air density at standard day conditions and ρ is the air density at the local altitude. f. "Approved", uniess used with reference to another person, means approved by the Administrator for use within the limits specified by the manufacturer and verified by compliance with the requirements of this standard. g. “Canopy”- The part of the parachute that opens up and fills with air and provides the lift and/or drag required to decelerate the payload to the desired value. h. “Certified”, unless used with reference to another agency, means certified by the cognizant agency as having met the requirements of this standard. i.
“Cognizant Agency” – The governmental agency or other organization tasked with oversight or regulation of aviation activities within a given geographical area or country. e.g. the Federal Aviation Administration (FAA) within the United States, the Joint Airworthiness Authorities (JAA) within the European Union and similar agencies worldwide. In some cases, the cognizant agency may delegate part or all of its authority to a subordinate agency such as a national aero club. j. “Drogue” – A small aerodynamic decelerator towed behind a falling body to slow its velocity. k. “Manufacturer”— The person (or business/corporate entity) who controls the design and quality of the article produced including the parts of them, and any processes or services related to them that are procured from an outside source. I. “Main Assisted Reserve Deployment (MARD) device” – An automatically releasable connection between the main parachute and the reserve deployment system which uses a malfunctioned main canopy to speed reserve deployment upon breakaway.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 2 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton S 47-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially n numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodicaly, at which time it may be reaffirmed, evised, or canceled. The PIA invites your writen comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-27
PIA TS 135
m. "Parachute" means a device used or intended to be used to retard the fall of a body or object through the air. n. “Parachutist in Command” – means the person making a tandem jump who: (1) Has final authority and responsibility for the operation and safety of the jump; (2) Has been designated as parachutist in command before the jump; and (3) Holds the appropriate rating for the conduct of the jump. o. “Passenger parachutist” means a person who boards an aircraft, acting as other than the parachutist in command of a tandem parachute operation, with the intent of exiting the aircraft while in-flight using the forward harness of a dual harness tandem parachute system to descend to the surface.
2.1.1 MAJOR COMPONENTS: For purposes of this document a parachute assembly normally, but not exclusively, consists of the following major components: a. Deployment control device such as a sleeve, bag, diaper, or functional equivalent. b. Deployment initiation device (pilot chute, drogue, or functional equivalent) and bridle. c. Canopy(s) including suspension lines, reefing device, and connector links (if used). d. Riser(s), when not integral with harness and/or canopy. e. Stowage container(s) or stowage pack(s). f. Harness (es). g. Primary actuation device (ripcord or functional equivalent). h. Reserve static line. Drogue canopy and bridle (if used with reserve and/or emergency parachutes). j. Drogue release device (if used with reserve and/or emergency parachutes).
2.1.2 SINGLE HARNESS RESERVE PARACHUTE ASSEMBLY: A certified parachute assembly that is worn in conjunction with a main parachute assembly and used by one person for premeditated jumps. This includes, as applicable, the reserve deployment initiation device, deployment control device, canopy, risers, stowage container, harness, primary actuation device, and reserve static line.
2.1.3 DUAL HARNESS RESERVE PARACHUTE ASSEMBLY: A certified parachute assembly used for premeditated jumps by two people: a parachutist in command and a second parachutist (each in his/her own harness), utilizing one main parachute assembly and one reserve parachute assembly. This assembly includes, as applicable, the reserve deployment initiation device, deployment control device, canopy, risers, stowage container, harness, primary actuation device, and reserve static line.
2.1.4 MAIN PARACHUTE ASSEMBLY: A non-certified parachute assembly that is worn in conjunction with a certified reserve parachute assembly as the primary parachute (the one intended for use) for premeditated jumps. The main parachute assembly shall consist of the main container and all associated parts of the main parachute that are not permanently attached to the certificated harness assembly.
2.1.5 SINGLE HARNESS EMERGENCY PARACHUTE ASSEMBLY: A certified parachute assembly that is worn by one person for emergency, (unpremeditated) use only. This assembly includes, as applicable, the deployment initiation device, deployment control device, canopy, risers, stowage container, harness, and primary actuation device.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 3 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this p publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Street, me: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your writen comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-28 Change 1 (December 2015)
PIA TS 135
2.1.6 FAILURE OF A PARACHUTE ASSEMBLY OR COMPONENT: The term “failure” in this document shall mean any change in a component or assembly that adversely affects its airworthiness. However, the use of consumable, frangible or single use parts shall be permitted in all assemblies and shall not be considered a failure if they function as designed.
2.1.7 FUNCTIONALLY OPEN: Functionally open shall mean a parachute sufficiently deployed and inflated to provide a rate of descent of not more than 24 ft/s (7.3m/s). This condition may be demonstrated by video, film or electronic data of the test in a manner determined by the manufacturer.
2.1.8 RESERVE STATIC LINE (RSL): A device connected to the main parachute assembly that is capable of actuating the reserve parachute assembly following a breakaway from the main canopy.
2.1.9 MAIN PARACHUTE BREAKAWAY DEVICE: A device used by the parachutist in command to separate the main parachute from the harness of a single or dual-harness reserve parachute assembly. The parachutist in command shall be able to operate the main parachute breakaway device for dual harness reserve parachute assemblies.
2.1.10 MAXIMUM OPERATING WEIGHT (MOW): The maximum operating weight is the total (gross) weight of all individuals or dummies and their equipment including the parachute assembly itself. MOW is also known as the “placard weight”.
2.1.11 MAXIMUM PACK OPENING SPEED (MPOS): The maximum pack open speed in KTAS (knots true airspeed) is the maximum speed at which the (reserve/emergency) parachute pack (container) is designed to be opened. This definition specifically allows for the wearing of parachutes in freefall and/or in aircraft at speeds higher than the maximum pack opening speed. MPOS is also known as the “placard speed”.
NOTE: In order to provide an inherently greater margin of safety without requiring that tests be conducted at all possible altitudes, all test conditions in this document are stated in KEAS and that all maximum pack opening speeds are stated in KTAS. In the event that a manufacturer elects to conduct further testing at higher altitudes, the placard limits may be changed to reflect any test conditions successfully conducted.
2.1.12 MINIMUM OPERATING WEIGHT (MinOW) The minimum operating weight is the lowest allowed total (gross) weight of an individual or dummy (or all individuals or dummies in the case of a tandem) and their equipment including the parachute assembly itself. The MinOW shall be specified by the manufacturer and may be any weight demonstrated to be appropriate by the manufacturer for the system.
2.1.13 SERVICE LIFE RESTRICTED ITEMS: Materials or products that, by design, are service life restricted for any reason (environmental, structural, chemical, etc.) may be used in any manner chosen by the manufacturer. Each such item must be marked in a manner that will allow maintenance personnel to determine the serviceable status of the part.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 4 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of th publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Street, 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your wrtten comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-29
PIA TS 135
3. MATERIALS AND WORKMANSHIP: Materials and workmanship shall be of a quality that documented experience and/or tests have conclusively demonstrated to be suitable for the manufacture of, and appropriate for the intended use in, personnel parachute assemblies. All materials shall remain functional for storage from -40 to +200°F (-40 to +93.3 °C), and from 0 to 100% relative humidity. All plated ferrous parts shall be treated to minimize hydrogen embrittlement.
4. DETAIL REQUIREMENTS
4.1 DESIGN AND CONSTRUCTION:
4.1.1 MATERIALS: All materials shall be designed to support the proof loads specified in the applicable specification, drawing, or standard, without failure. In the absence of an applicable specification, drawing, or standard for a particular material, successful completion of the qualification tests listed under section 4.3 shall be considered adequate evidence of suitability.
4.1.2 STITCHING: Stitching shall generally be of a type that will not ravel when broken. Note that this is not required for consumable or frangible parts.
4.1.3 MAIN PARACHUTE ASSEMBLY: When installed but not deployed, the main parachute assembly shall not interfere with the proper function of the reserve parachute assembly. Ref: Table 2
4.1.4 PRIMARY ACTUATION DEVICE/RIPCORD: The primary actuation device/ripcord, including all joints, shall withstand the test loads of 4.3.2 without failure. The primary actuation device/ripcord shall meet the human-factors requirements of 4.3.3., if applicable.
4.1.5 RESERVE STATIC LINE (RSL): The reserve static line, if used, including all joints shall withstand the test loads of 4.3.2 without failure and shall meet the functional requirements of 4.3.8.2.
4.1.6 HARNESS RELEASE: The harness shall be so constructed that, after landing, the parachutist can separate himself from the main and reserve canopies and/or harness assembly unaided. On a dual harness, reserve parachute assembly, the parachutist in command must be able to separate himself and the second parachutist from the reserve canopy and/or harness assemblies unaided.
4.1.7 DROGUE PARACHUTE ASSEMBLY & RELEASE: For reserve or emergency parachute assemblies, incorporating a drogue, the drogue release shall be tested at an equivalent force to the drag force generated at the MOW and MPOS. The human release force shall not be less than 5 lbf (22.2N) and must not exceed 22 Ibf (97.9N). The release shall meet the human-factors requirements of 4.3.3.
4.1.8 DATA CARD POCKET; STOWAGE CONTAINER: The stowage container shall be provided with a parachute data card pocket constructed such that the card will not be easily lost and will be readily accessible, when the parachute is packed in the container. PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 5 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this pu ublication may be reproduced without prior written permitssion from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakt -674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by referenc e by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your writen comments and suggestions. Copyright 2010 Parachute Industry Association.
A-30 Change 1 (December 2015)
PIA TS 135
4.2 MARKING REQUIREMENTS: Marking requirements are listed in Table 1.
NOTE: The data items listed in Table 1 need not be marked at the same location on the component as long as all of the pertinent information is permanently marked.
4.2.1 MARKING, STOWAGE CONTAINER - OPERATING LIMITS: The minimum and maximum operating limits in Table 1 shall be marked/placarded on or attached to the outside of the parachute stowage container (pack). The marking/placard may refer to the owner's manual for the minimum operating weight. The lowest maximum operating weight of any component in the assembly (canopy, harness, etc.) and the lowest maximum pack opening speed of any component (canopy, harness, etc.) shall be marked on the outside of the stowage container (pack) in such a location as to be readily available to the user during donning of the parachute assembly and subject to a minimum of obliteration during use.
This information may alternately be placed in a pocket marked with the legend Operating Limitations Inside’; the pocket must be readily available to the user during donning of the parachute assembly and subject to a minimum of obliteration during use.
NoTE: The maximum pack opening speed and minimum and maximum weight markings shall be in a block typeface, in a minimum size of 0.375 inch (9.5 mm) tall (27 point type). The other information required by Table 1 may be marked in another location, if desired.
4.2.2 MARKING, CANOPY - STATEMENT OF USE: Each certified canopy shall be marked to show its approved use as follows:
4.2.2.1 “Single Harness Emergency Parachute Canopy” “Single Harness Reserve Parachute Canopy” “Single Harness Emergency/Reserve Parachute Canopy” “Dual Harness Reserve Parachute Canopy”
4.2.2.2 Each canopy (single harness types only) that has not been tested in accordance with the breakaway tests of Section 4.3.8.2 shall be marked as follows:
"LIMITATION: May not be used with main parachute breakaway device”.
4.3 QUALIFICATION TESTS: The minimum performance standards listed in Tables 2, 3 and 4 shall be met. There shall be no failure to meet any of the requirements during the qualification tests of this section. In case of a failure, the cause must be found, corrected, and all affected tests repeated.
4.3.1 PACKING METHOD: The packing method must be specified and the identical packing method must be used for all of the functional and structural tests.
4.3.2 PRIMARY ACTUATION DEVICE/RIPCORD TEST: (a) The ripcord, including all joints, shall not fail under a straight tension test load of 300-Ibf (1337.7 N) applied for not less than 3 seconds.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 6 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part oft publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Stree 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by referenee by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-31
PIA TS 135
(b) If the reserve is to be static line actuated by releasing the main canopy, the reserve static line, if used, must not fail under a straight tension test load of 300-Ibf (1334.5 N) applied for not less than 3 seconds.
(c) If the reserve ripcord is to be static lined from an aircraft the reserve ripcord/static line, must not fail under a straight tension test load of 600-Ibf (2668.9 N) applied for not less than 3 seconds.
(d) Rigid pins, if used, shall not yield under a load of 8-Ibf (35.6 N) applied to the cable (or equivalent) perpendicular to the axis of the pin, for not iess than 3 seconds. The pin shall be supported for 0.5 in (12.7-mm) maximum at the end farthest from the cable attachment. All 4.3.3 human factors tests shall be performed using a primary actuation device/ripcord that has passed this test.
4.3.3 HUMAN FACTORS AND ACTUATION FORCE TESTS: An anthropometrically diverse group of individuals (consisting of a representative group of no less than 3 males and 3 females) from the intended user group shall be employed for all human factors tests in 4.3.3. All individuals shall be able to operate the subject device without any undue difficulty. Table 2 lists the required test conditions and number of tests for each particular component. Additional information for the component tests is listed below.
TESTS: Under normal design operating conditions, all devices tested under this paragraph shall result in a positive and quick operation of the device within the following load range applied to the handle: (a) a load applied at the handle of not less than 5 Ibf (22.2 N), applied in the direction giving the lowest pull force, (b) a load applied at the handle of not more than 22 Ibf (97.9 N), applied in the direction of normal design operation, (c) for chest type parachute assemblies, the maximum pull force shall be 15 Ibf (66.7 N), (d) the primary actuation device shall be tested in accordance with Table 2, (e) the emergency/reserve drogue release (if used) shall be tested in accordance with Table 2.
NoTE: For these tests, the primary actuation device (ripcord or equivalent) shall be equipped with a tamper-indicating device (i.e. seal thread or equivalent) of the same type that will be required for production articles in service.
4.3.4 HUMAN FACTORS TESTS, HARNESS: Harnesses shall demonstrate that they will perform the basic function of retaining the body at the end of the parachute suspension system in an inherently secure manner. This requirement shall be demonstrated by passing all live drop tests in Table 3.
4.3.5 ENVIRONMENTAL TESTS: Three drops shall be made at 60 KEAS except that prior to the test the parachute assembly shall be subjected to the following preconditioning: (These tests may be combined with other tests.)
4.3.5.1 Precondition for 16 hours at not less than +200 °F (93.3 °C), stabilize to ambient and test drop.
4.3.5.2 Precondition for 16 h at not greater than -40 °F (-40 °C), stabilize to ambient and test drop.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 7 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of t blication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton one: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-32 Change 1 (December 2015)
PIA TS 135
4.3.5.3 Precondition for not less than 400 continuous hours with a 200 Ibf (889.6 N) or greater load applied to compress the pack in a manner similar to that most likely to be encountered in actual use. Test drop within 1 hour after removing the load.
4.3.5.4 Alternate preconditioning. The preconditioning requirements for 4.3.5.1 and 4.3.5.3 may be combined as follows: The complete test parachute assembly may be placed in a vacuum bag and preconditioned at +180 °F (82.2 °C) for 18 hours at a constant vacuum of not less than 25” Hg (0.846 bar). Stabilize to ambient and drop.
4.3.6 STRUCTURAL OVERLOAD TESTS: No material(s) or device(s) that attenuates shock loads and is not an integral part of the parachute assembly or component being certified may be used. Tests may be conducted for either a complete parachute assembly or separate components. There shall be no evidence of material, stitch, or functional failure that will affect airworthiness. For reusable items the same items shall be used for all 4.3.6 tests. Peak opening force shall be measured on all 4.3.6 tests. The parachute must be functionally open within the number of seconds calculated for 4.3.8 tests. Parachute assemblies shall be tested in accordance with the following schedule:
(a) Test weight = Maximum operating weight x 1.2 Test speed = Maximum pack opening speed x 1.2
-OR-
(b) Test weight = Maximum operating weight multiplied by the factor from Figure 1 Test speed = Maximum pack opening speed multiplied by the factor from Figure 1
However, the test speed must not be less than 180 KEAS (333.4 km/h) for reserve and emergency parachute assemblies and the test weight must not be less than 264 Ib. (120 kg).
For dual harness parachute assemblies the test weight must not be less than 600 Ib. (272.7 kg) and the test speed must not be less than 200 KEAS (370.4 km/h).
4.3.6.1 STRENGTH TEST, COMPLETE PARACHUTE ASSEMBLY: Three drops shall be made with weight and speed in accordance with 4.3.6. When using test method (b), in 4.3.6 a 4th drop must be added using the same parachute under the same conditions in the first three drops. Where non-positive locking hardware is used to attach the canopy or riser(s) to the harness, a cross connector must be used and one of the above drops shall be with only one attachment engaged to test the cross connector and hardware.
4.3.6.2 STRENGTH TEST, ALTERNATE MEANS OF COMPLIANCE CANOPY (ONLY): Three drops shall be made with a gross weight and speed in accordance with 4.3.6. When using test method (b), in 4.3.6 a 4th drop must be added using the same canopy under the same conditions in the first three drops. A test vehicle (e.g., a bomb) may be used. The canopy and any required additional components (i.e., deployment device, pilot chute, and risers) shall be tested as a unit. The connector links (if used) shall be attached to the risers in the same manner as the intended use and the riser(s) should be secured to the test vehicle in a manner appropriate to the test objective. For example, if the parachute risers are to be tested on the bomb drop, it should be arranged in a manner as to duplicate the loading found on the personnel parachute harness. Where non-positive locking hardware is used to attach the canopy or riser(s) to the harness, a cross connector must be used and one of the above drops shall be with only one attachment engaged to test the cross connector and hardware.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 8 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. ion may be reproduced without prior written permisseion from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committe, 3833 West website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be erors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright 2010 Parachute Industry Association.
Change 1 (December 2015) A-33
PIA TS 135
4.3.6.3 STRENGTH TEST, ADDITIONAL MEANS OF COMPLIANCE HARNESS (ONLY): A harness may, at the manufacturer's option, be placarded with a higher average peak opening force than what was measured in 4.3.6 tests by performing additional tower drop tests as outlined below:
The harness shall be drop tested using a torso shaped dummy, three (3) times for each of four (4) different loading conditions. The dummy weight shall be not less than 75% of harness maximum operating weight and the drop distance shall be as necessary to generate the required forces. Up to three (3) separate harnesses may be used; however each harness shall be subjected to a minimum of one test at each of the following four test conditions.
(a) Test condition one – All risers loaded to a combined load of at least 100% of placard maximum load. (b) Test condition two – Only left side harness/canopy attachment point(s) loaded to a combined load of at least 66% of placard load. (c) Test condition three – Only right side harness/canopy attachment point(s) loaded to a combined load of at least 66% of placard load. (d) Test condition four – Each unique brake setting shall be tested to a minimum of 16.7% of placard load if applicable.
4.3.6.4 STRENGTH TESTS, ALTERNATE MEANS OF COMPLIANCE, DROGUE CANOPY (ONLY) For parachute assemblies in which a drogue parachute canopy is an integral part of the reserve or emergency parachute assembly, the drogue may be separately tested at the conditions determined in 4.3.6. The drogue canopy itself and all related components of the drogue assembly must be tested as a functional subsystem of the parachute assembly.
4.3.7 FUNCTIONAL TESTS (Twisted Lines): A minimum of 5 drops shall be made with a weight not more than the maximum operating weight dummy or person1 in each harness. The airspeed at the time of pack opening shall be 60 KEAS (111.1 km/h)
Procedural Note: The suspension lines shall be twisted together (360 degrees) three times in the same direction within the upper one third of the suspension line length beginning immediately below the attachment point to the canopy. The twists shall be placed in the lines before the suspension lines are stowed.
Performance Requirement: The parachute must be functionally open within 133% of the time calculated in 4.3.8 from the time of pack opening.
4.3.8 FUNCTIONAL TESTS (Normal Pack - AII Types): Opening Time or Altitude Loss: Using the MOW in pounds and the MPOS in KTAS for all 4.3.8 tests the maximum allowable opening time and the maximum allowable altitude loss on any drop shall be determined from the following formulas..
(a) The greater of 3.00 seconds or the value determined as follows:
A person's or individual's body weight may be increased to equal the maximum operating weight by using a weight belt or similar device.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 9 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part ofthis ublication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Street, Skokie, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright 2010 Parachute Industry Association.
A-34 Change 1 (December 2015)
PIA TS 135
Opening Time Allowed (sec.) = (MOW – 250) * 0.01 + (MPOS/150 * 3.0)
-OR-
(b) The greater of 300 feet or the value determined as follows:
Altitude Loss Allowed (ft) = (MOW-250) + (MPOS/150 * 300)
4.3.8.1 DIRECT DROP TESTS: There shall be a minimum of 48 tests at weights and airspeeds (at the time of pack opening) as outlined in Table 3. The test condition airspeeds are in KEAS. From the time of pack opening, the parachute canopy must be functionally open within the allowed time or altitude as calculated in 4.3.8.
(a) The manufacturer shall specify the Maximum Operating Weight and the Minimum Operating Weight. (b) The Maximum Pack Opening Speed (MPOS) shall not be less than 150 knots. (c) The MPOS and MOW shall be established by successful completion of the structural overload testing in Paragraph 4.3.6 (d) The manufacturer will be allowed to select whether to measure altitude loss or opening time, but within each block on the test grid the same method must be used. (e) The maximum allowable opening time shall be calculated using the formula in 4.3.8(a): there shall be a minimum of 4 successful tests for each block; the opening times will be averaged and presented to the Administrator in the format shown in Figure 2. (f) The maximum allowable altitude loss shall be calculated using the formula in 4.3.8(b): there shall be a minimum of 4 successful tests for each block; the altitude loss must be averaged and presented to the Administrator in the format shown in Figure 2. (g) The opening times and/or altitude loss for each test block will be averaged and published in the format shown in Figure 2 in the owner's manual or in some other readily available location.
NOTE: If a “MARD device” option is offered, an additional 8 drops at weights and airspeeds (at the time of pack opening) must be performed as outlined in the Table 3 with the MARD attached.
4.3.8.2 BREAKAWAY DROP TESTS (systems with main canopy release): Eight drop tests shall be made by breaking away from an open and normally functioning main parachute canopy and actuating the reserve parachute within 2 seconds of the breakaway. These tests shall be conducted by a person (or suitable other devices) weighing not more than the maximum operating weight. The initial vertical velocity shall be less than 20 ft/s (6.1 m/s) and the total velocity less than 36 ft/s at the time of breakaway. From the time of pack opening, the parachute canopy must be functionally open within the altitude or within the allowed time as calculated in 4.3.8.
NOTE: (a) If a reserve static line is part of the assembly, then 4 of the breakaway drops shall be made with the reserve static line actuating the reserve pack. (b) If a “MARD device” option is offered, an additional 16 drops at weights and airspeeds (at the time of pack opening) must be performed as outlined in the Table 3 with the MARD attached. PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 10 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Street, Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference b ll those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibilty for accuracy. The PIAreviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-35
PIA TS 135
4.3.9 RATE OF DESCENT TESTS (METHOD 1): Per Table 3, there shall be not less than 6 drops, with an individual and/or dummy in each harness weighing not less than the maximum operating weight2. The average rate of descent shall not exceed 24 ft/s (7.3 m/s) and the total velocity shall not exceed 36 ft/s (11.0 m/s) in an unaltered post deployment configuration, corrected to standard day sea level altitude conditions. The rate of descent measurement shall be taken over a minimum interval of 100 ft (30.5 m). These tests may be combined with other tests in this section.
4.3.9.1 RATE OF DESCENT TESTS (METHOD 2): The rate of descent corrected to standard day sea level altitude conditions shall not exceed 5 ft/sec (1.5m/sec) at touchdown with appropriate control manipulations and the average rate of descent shall not exceed 24 ft/sec (7.3 m/s) in the unaltered post deployment configuration over a minimum interval of 100 ft (30.5m). These tests may be combined with other tests in this section.
NOTE: If the total velocity exceeds 36 ft/sec at maximum certified weight, the container or harness (if integral to the container) must be marked in an area readily visible to the user: “For experienced parachutists only. The owner's manual contains experience requirements."
4.3.10 STABILITY TESTS: Per Table 3, there shall be not less than 6 drops, at the minimum operating weight. The oscillations shall not exceed 15° from the vertical, in an unaltered post-deployment configuration. These tests may be combined with other tests in this section.
4.3.11 LIVE TESTS: Per Table 3, there shall be a minimum of 4 live tests with an individual weighing not more than the maximum operating weight in each harness. Two drops shall include a freefall of not more than 3 seconds and 2 drops shall include a freefall of at least 20 seconds. These tests may be conducted in conjunction with functional and/or rate of descent tests when practical. The user(s) must suffer no significant discomfort from the opening shock and must be able to disengage himself (themselves) unaided from the harness after landing. For this test the standard harness may be altered to permit attachment of a certified reserve parachute assembly (less harness) provided that such alteration does not interfere with the normal operation of the parachute assembly being tested. Reserve parachute assemblies shall be tested with the main compartment(s) full and empty, with a minimum of two tests each.
NOTE: Live tests for Dual Harness Reserve Parachute Assemblies may be tested with the parachutist in command and a dummy payload in the passenger harness.
5. COMPONENT QUALIFICATIONS: Any single component, assembly of components, group of components or group of assemblies may be certified. Table 4 lists the appropriate test paragraphs for each of the major components. Any components not listed in Table 4 shall be tested according to all applicable sections of this document based on the components function.
A person's or individual's body weight may be increased to equal the maximum operating weight by using a weight belt or similar device. PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 11 of 18 DISTRIBUTION STATEMENT: AII Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committe,3833 West Oakton Stret, Skokie, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-36 Change 1 (December 2015)
PIA TS 135
5.1 COMPONENT COMPATIBILITY: The component manufacturer shall provide a means of determining compatibility and shall provide specific guidance to ensure that form, fit and function of all components, as assembled, are within acceptable limits for each individual component and the assembly as a whole.
5.2 COMPONENT QUALIFICATION BY GROUP: Components may be qualified as a group consisting of a range of scaled sizes. Separate elements of the component design may be linearly scaled at different rates as specified in the component drawings provided that fit, form, and function are not adversely affected. For canopies, the range may consist of scaled sizes to a maximum area of three times the smallest size.
When certifying components as a group, only the largest and the smallest members of the group must be tested in accordance with the appropriate sections of this document.
5.3 MAINTENANCE REQUIREMENTS: The manufacturer of each component is responsible for developing and disseminating the maintenance requirements for each component, specifically including the inspection interval, repack cycle, service life, criteria for continued airworthiness and the qualifications required of maintenance personnel.
5.4 FITTING REQUIREMENTS: The manufacturer is responsible for developing and disseminating instructions identifying the correct method of fitting the equipment to the user.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 12 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Commitee, 3833 West Oakton Street, website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-37
PIA TS 135
PIA TS-135 - Figure 1 Multiplier Factors for Structural Overload Testing Per Paragraph 4.3.6
2.00
Muilier 1.50 1.43
1.1
1.00
100 150 200 250 300
Maximum Pack Opening Speed for Placard (KTAS)
Airspeed Multiplier Weight Multiplier • Resultant Kinetic Energy Factor
PIA TS-135 Figure 2 Direct Drop Tests Per Paragraph 4.3.8.1
Test Speed
Test Weight 60 KEAS 85 KEAS MPOS x 80% MPOS x 100%
Minimum Operating 4 4 4 4 Weight Averaged Operating 4 4 4 4 Weight* Maximum Operating 4 4 4 4 Weight Minimum Total (direct drop) Functional Tests Required 48
*Averaged Operating Weight is defined as (Maximum Operating Weight + Minimum Operating Weight)/2 Average test weights shall be +/- 5% Minimum test weights shall be +1%/-10%. Maximum test weights shall be +10%/-1%
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 13 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committee, 3833 West Oakton Street, Skokie, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by referenc e by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-38 Change 1 (December 2015)
PIA TS 135
PIA-TS-135 - Table 1.
Data Marking Requirements
Marking Data Requirements Dep D- g tc.) Res Euyy nopy Sto ner Rese e e ed) Harnl sl ner Rise es) Resy or ser (s d) (i d)
Manufacturers Name, Code or Symbol X X X X X X X X X X Part Number (w/dash numbers) X X X X X X X X X X Serial or Lot Control Number X X X X X X X X X Date of Manufacture (month and year minimum) X X X X X X X X X Date to Be Removed from Service (if applicable) X X X X X X X X X Maximum Pack Opening Speed (KEAS) 4.3.6 X X X X X Maximum Gross Weight (Ib) if applicable 4.3.6 X X X Minimum Gross Weight (Ib) 4.2 X Average Peak Force Measured during 4.3.6 tests 4.3.6 X X Appoved for Use Statement 4.2.2 X Statement of Authorization Under TS0-C-23e and/or (J) TSO-C-23e if applicable X X X X X X X Operators Warning Label with Maximum Operating Limits 4.3.6 X X Operators Warning Label and location for component operating limitations 4.2.1 X Operators Warning Label with Maximum Total Velocity for intended use (Student, Tandem, Emergency Air Crew or Other). 4.3.9 X Maximum Drogue deployment speed 4.3.6 X
For ripcords, either lot control number or date of manufacture may be marked provided that tracabillity is maintained At a minimum, Maximum Operating Limitations must include maximum pack opening speed and maximum gross w eight. Manufacturer may voluntarily derate operating limitations. Redundant marking may be eliminated for components w hich are permanently joined at the time of manufacture. If this is the case, the marking w ill be located on the most visible component, normally the container.
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 14 of 18 DISTRIBUTION STATEMENT: Al Rights Reserved. No Part of this publication may be reproduced without prior written permission from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committe, 3833 West Oakton Street, Skokie, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by referenc e by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions. Copyright © 2010 Parachute Industry Association.
Change 1 (December 2015) A-39
PIA TS 135
PIA-TS-135 - Table 2 Human Factors and Actuation Force Tests Primary Actuation Device / Ripcord Pack Emergency Parachute Single Harness Reserve Dual Harness Reserve Data Test Load Second Suspended Conditio Assembly Parachute Assembly Parachute Assembly Required Condition Factor Parachutist by n Male Female Male Female Male Female P/F Force Upright Standing N/A N/A N/A N/A 6 6
P/F Force Standing Upright N/A none/with N/A Full 3 3 3/3 3/3
P/F Force Standing Upright N/A none/with N/A Empty 3 3 313 3/3
P/F Force Harness Suspended 1g none Main Risers Empty 3 3 3 3
P/F Force Harness Suspended 1g with Main Risers Empty 3 3 Additional tests if emergency/reserve drogue is used: P/F Force Harness Suspended 4.1.7 N/A Drogue N/A 6 6
P/F Force Suspended Harness 4.1.7 none Drogue Full 3 3 3 3
P/F Force Harness Suspended 4.1.7 none Drogue Empty 3 3 3 3
P/F Force Harness Suspended 4.1.7 with Drogue Full 3 3
P/F Force Harness Suspended 4.1.7 with Drogue Empty 3 3 Total Tests Required in This Section (drogue / no drogue) 24/12 30/18 60/36 4.1.7 - The drogue release shall be tested at an equivalent (or greater) force to the drag force generated at the MOW and MPOS. Notes: 1. All tests must be conducted with a reserve/emergency canopy assembly packed for intended use. 2. N/A = Not Applicable 3. P/F = Pass/Fail
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 15 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without rior written permission from Parachute Industry Association PIA Headquarters, Parachute Cetification Standards Commite, 833 West Oakton Stret, Skoki, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or website www.pia.com for contact details. Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by reference by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there fom is the sole responsibility ofthe user. There may be emrors, especiallyin umbers. PIA disclaims any responsibility for acuracy. The PIA reviews each technical publication perodically, t which time it may be reaffirmed, revised, or canceled The PIA invites your writen comments and suggestions. Copyright © 2010 Parachute Industry Association.
A-40 Change 1 (December 2015)
PIA TS 135
PIA TS-135 Table 3 Required Qualification Tests
Notes on Data Required Test Description Paragraph Reference
Speed at Pack Opening Test Weight Main Pack Condition (KEAS)
Emergency Single or Dual Parachute Harness Reserve Assemblies Parachute Assembly Live Live
Dummy
1,8,5 Primary Actuation Device/Ripcord Test 4.3.2
IAW 4.3.2 (a) through (d)
Dummy
IAW Table 2 and as described in paragraphs 4.3.3(a) through (e)
1,2,5 Human Factors and Actuation Force Tests 4.3.3
Demonstrated by successful completion of live jumps per paragraph 4.3 .11
Human Factors Tests, Harness 4.3.4
Environmental Tests 4.3.5 1,3,5 Precondition to +200 F 4.3.5.1 1,3,5 Precondition to -40 F 4.3.5.2 1,3,5 Precondition - compressed pack 4.3.5.3 1,3,5 Precondition - alternate to 4.3.5.1 & 4.3.5.3 4.3.5.4
Structural Overload Tests 4.3.6
1,2,3,5 Complete Assemblies 4.3.6.1
1,2,3,5 Alternate Means of Compliance, Canopy Only 4.3.6.2
1,2,3,5 Altermate Means of Compliance, Haress Only 4.3.6.3
1,2,3,5 Drogue (if applicable) 4.3.6.4
1, 3 (or 4), 5, Functional Tests, Twisted Lines 4.3.7
60 KEAS <= MaxOW 60 KEAS <= MaxOW 60 KEAS <= MaxOW 60 KEAS <= MaxOW
Fig. 1 Fig. 1 N/S
Fig. 1 Fig. 1 N/S
Fig. 1 Fig. 1 N/S Fig. 1 Fig. 1 N/S
60 KEAS <= MOW N/S
1 1 1 1 1 1 1 1
3 3
3 3 N/A N/A 3 3
3 3
5 5
Opening Time allowed shall be calculated IAW paragraph 4.3.8 (a).
1, 3 (or 4), 5, Functional Tests, (Normal Pack all types) 4.3.8
Opening Altitude allowed shall be calculated IAW paragraph 4.3.8 (b)
1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1
1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1
1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1 1, 3 (or 4), 5, Direct Drop 4.3.8.1
60 KEAS MinOW Empty 60 KEAS AvOW Full 60 KEAS MaxOW Empty 60 KEAS MinOW Full 60 KEAS AvOW Empty 60 KEAS MaxOW Full Total Drops at 60 KEAS 85 KEAS MinOW Empty 85 KEAS AvOW Full 85 KEAS MaxOW Empty 85 KEAS MinOW Full 85 KEAS AvOW Empty 85 KEAS MaxOW Full Total Drops at 85 KEAS 80% MPOS MinOW Empty 80% MPOS AvOW Full 80% MPOS MaxOW Empty 80% MPOS MinOW Full 80% MPOS AvOW Empty 80% MPOS MaxOW Full Total Drops at 80% MPOS
4 2 N/A 2 4 2 N/A 2 4 2 N/A 2 12 12 4 2 N/A 2 4 2 N/A 2 4 2 N/A 2 12 12 4 2 N/A 2 4 2 N/A 2 4 2 N/A 2 12 12
PIA TS-135, Revision 1.4, Issued April 22, 2010, Page 16 of 18 DISTRIBUTION STATEMENT: All Rights Reserved. No Part of this publication may be reproduced without prior written permisson from Parachute Industry Association. PIA Headquarters, Parachute Certification Standards Committe, 833 West Oakton Street, Skokie, IL 60076 Phone: 847-674-9742 Fax: 847-674-9743 or
website www.pia.com for contact details.
Disclaimer: This document is published by the PIA to provide technical and engineering standards that can be used by referenc e by all those who may benefit from them. The use of this document is entirely voluntary, and its applicability and suitability for any particular use, including any patent or trademark infringement arising there from, is the sole responsibility of the user. There may be errors, especially in numbers. PIA disclaims any responsibility for accuracy. The PIA reviews each technical publication periodically, at which time it may be reaffirmed, revised, or canceled. The PIA invites your written comments and suggestions.
Copyright © 2010 Parachute Industry Association.
Continue reading ↓ 120 of 174 passages shown