Radar Vectors
Handbook Current Issued 2024 8 pages Copy saved Nov 20, 2026

FAA-H-8083-13B Ch. 2 Components and Systems

Official source ↗ Open PDF

Introduction

39243

Glider Design

20967 Glider airframes include a fuselage, wings, and empennage or tail section. [Figure 2-1]

20969

Right aileron

Left aileron

Spoiler/Dive brake

Empennage Fuselage

Landing gear Left wing

Right wing

Pilot Station

Figure 2-1. Components of a glider.

The Fuselage

20968 The fuselage contains the controls for the glider, as well as a seat for each occupant. The wings and empennage attach to the fuselage. Manufacturers typically use composites, fiberglass, or carbon fiber, however in the past manufacturers used wood, fabric over steel tubing, aluminum, or a combination of these materials to build a fuselage.

Introduction

20943 When air flows over the wings of a glider, the wings produce lift that allows the aircraft to stay aloft. Glider wing designs produce maximum lift with minimum drag.

20970 Glider wings incorporate several components that help the pilot maintain the attitude of the glider and control lift and drag. These include ailerons and other lift and drag devices.

Ailerons

Figure 2-1: picture of page 1Figure 2-1 · page 1
Picture of the page from the copy saved here

20973 The ailerons attach to the outboard trailing edge of each wing. When the pilot moves the aileron control to the right of center, the right aileron deflects upward [Figure 2-2] and the left aileron deflects downward. In flight and with air flowing over the wings, these deflections result in increased lift on the left wing and decreased lift on the right wing. The increased lift on the left wing and decreased lift on the right wing apply a force to roll the glider to the right. Moving the aileron

Figure 2-2: picture of page 2Figure 2-2 · page 2
Picture of the page from the copy saved here

Chapter 2: Components & Systems

Chapter 2: Components & Systems

control to the left of center deflects the right aileron down and the left aileron up. This applies a force to roll the glider to the left.

20974

Lower camber

Upper camber

Chord Line

Chord Line

Chord Line

Leading Edge Trailing Edge

Figure 2-2. The ailerons change the camber or curvature of the wing and increase or decrease lift.

Lift/Drag Devices

20975 Gliders may use other devices that modify the lift/drag of the wing. These high drag devices include spoilers, dive brakes, and flaps. [Figure 2-3] Spoilers extend from the upper surface of the wings, alter the airflow, and cause the glider to descend more rapidly. Dive brakes extend from both the upper and lower surfaces of the wing and increase drag. Some high-performance gliders have dive brake speed limitations to prevent structural damage.

20977

Dive brake Dive brake

Spoiler Spoiler

Flap Flap

Figure 2-3. Types of lift/drag devices.

Figure 2-3: picture of page 2Figure 2-3 · page 2
Picture of the page from the copy saved here

20976 Some gliders have flaps installed on the trailing edge of each wing inboard of the ailerons, which can change lift, drag, and descent rate. The pilot can generally set flaps in three different positions, which are trail, down, or negative. [Figure 2-4] When the pilot sets the flaps to deflect downward in flight, the wing produces more lift and drag. On the other hand, a negative flap position results in reduced lift and drag.

20979

Flaps 0 (trail)

Flaps down

Flaps negative

Figure 2-4. Flap positions.

Empennage

20981 The empennage includes the entire tail section, consisting of the fixed surfaces, such as the horizontal stabilizer and vertical fin, and movable surfaces, such as the elevator or stabilator, rudder, and any trim tabs. The two fixed surfaces act like the feathers on an arrow to steady the glider and help maintain a straight path through the air. [Figure 2-5]

20982

Rudder Vertical stabilizer

Elevators

Horizontal stabilizer

Figure 2-5. Empennage components.

Figure 2-4: picture of page 3Figure 2-4 · page 3
Picture of the page from the copy saved here

20984 The rudder attaches to the back of the vertical stabilizer, and the pilot deflects the rudder using foot pedals. The rudder controls yaw and turn coordination during flight.

20983 During straight-and-level flight, pilot-controlled deflection of the elevator applies a force to move the glider's nose up and down relative to the horizon. Raising the nose results in lower airspeed while lowering the nose increases airspeed. Instead of a horizontal stabilizer and elevator, some gliders use a stabilator, where the entire horizontal tail surface pivots up and

down on a central hinge point. Pilots refer to the movement of the elevator or stabilator as controlling the pitch attitude of the glider.

20986 When the pilot deflects the pitch controls from the neutral position, the airflow pushes back against the controls. This opposing force provides feedback to the pilot but also adds to the pilot’s workload. The pilot may relieve the elevator control pressure using elevator trim. A common trim system consists of a small, pilot-controlled adjustable tab on the trailing edge of the elevator. [Figure 2-6] Trim tabs come in servo and anti-servo designs. [Figure 2-7] A servo tab relieves pressure. The pilot can adjust an anti-servo tab, usually installed on stabilators, to relieve pressure, but it also self-adjusts to increase opposing pressure when the pilot increases stabilator displacement.

20987

Horizontal stabilizer Elevator

Trim tabs

Rudder

Figure 2-6. Additional empennage components.

20989

Stabilator

Anti-servo tab

Figure 2-7. An anti-servo tab.

Figure 2-6: picture of page 4Figure 2-6 · page 4
Picture of the page from the copy saved here

20990 Glider designs with a conventional tail incorporate the horizontal stabilizer mounted at the bottom of the vertical stabilizer. T-tail gliders have the horizontal stabilizer mounted on the top of the vertical stabilizer forming a "T" shape. V-tails have two tail surfaces mounted to form a “V” that combines elevator and rudder movements.

Towhook Devices

20991 Gliders that launch using a tow have an approved towhook. For an aerotow, the crew normally connects the tow line to a towhook located on or just under the nose of the glider. For a tow using a winch or ground vehicle, the crew attaches the tow line to a towhook positioned below the glider center of gravity (CG)—the point where the glider would balance on the ground if lifted from above or below that position. [Figure 2-8]. Both towhook designs allow for quick release of the rope or cable when the glider pilot pulls the release handle. An aerotow launch of a glider using a specific towhook may only occur if the Glider Flight Manual/Pilot’s Operating Handbook approves the procedure.

20993

Aerotow

Ground launch

CG

CG

Figure 2-8: picture of page 5Figure 2-8 · page 5
Picture of the page from the copy saved here

Center of gravity CG towhook

Nose-mounted towhook

Figure 2-8. Tow hook locations.

Powerplant

20994 While tow planes provide the most common means to launch a glider in the United States, self-launching gliders with builtin engines have become more commonplace.

Self-Launching Gliders

20995 There are two types of self-launching gliders: touring motor gliders and high-performance self-launching gliders.

Touring Motor Gliders

25489 Touring motor gliders have a nose-mounted engine and a full feathering propeller. [Figure 2-9] Although touring motor gliders have some basic airplane characteristics, they are certified in the glider category.

20997

Figure 2-9. A Grob G109B touring motor glider.

High-Performance Gliders

20996 High-performance self-launching gliders have engines that retract into the fuselage for minimal drag. [Figure 2-10] The propeller may fold, or simply align with the engine. This configuration preserves a smooth low drag configuration.

20998

Figure 2-10. A DG-808B 18-meter high-performance glider in self-launch.

Gliders with Sustainer Engines

Figure 2-9: picture of page 5Figure 2-9 · page 5
Picture of the page from the copy saved here

20999 Some gliders have sustainer engines powered by either electricity or gasoline. A pilot can use a sustainer engine to remain aloft; however, sustainer engines do not provide sufficient power to launch the glider and may not have enough power to compensate for sinking air. [Figure 2-11]

21000

Figure 2-11. A Schleicher ASG-29 E with gasoline sustainer engine mast extended.

Landing Gear

21001 A glider landing gear system usually includes a main wheel. Gliders designed for high speed and low drag often feature a retractable main landing gear. Other components may include a front skid or wheel, a tail wheel or skid, or wing tip wheels or skid plates. [Figure 2-12]

21002

Retractable main wheel

Fixed main wheel

Tailwheel

Wingtip skid

Tailwheel

Wingtip wheel

Breakaway tailwheel

Nosewheel

Fixed main wheel

Skid

Figure 2-12. Landing gear wheels on a glider.

Figure 2-11: picture of page 6Figure 2-11 · page 6
Picture of the page from the copy saved here

51207 Almost all high-performance gliders have retractable landing gear, so pilots should include landing gear down in their prelanding checklist. Most landing gear handles are on the right side of the pilot station. However, a few models have gear handles on the left side, and pilots should use caution when reaching for a gear handle on the left to make sure it controls the gear and not flaps or airbrakes. A common error includes neglecting to retract the landing gear after takeoff, and then mistakenly retracting it as part of the prelanding checklist.

51208 Some high-performance gliders have only one center of gravity (CG) tow hook either ahead of the landing gear or in the landing gear well. With a CG hook within the landing gear well, retracting the gear on tow interferes with the tow line. Even if the glider has a nose hook, retracting the gear should wait. A CG hook, as compared to a nose hook, makes a crosswind takeoff more difficult since the glider can weathervane into the wind more easily. In addition, a CG hook makes the glider more susceptible to kiting (climbing above the tow plane) on takeoff, which threatens the safety of the tow pilot.

Wheel Brakes

21004 Early gliders often relied on friction between the nose skid and the ground to come to a stop. Later models use a wheel brake mounted on the main landing gear wheel, which helps the glider slow down or stop after touchdown. Modern gliders commonly use a hydraulic disk brake, which provides substantial braking capability.

Chapter Summary

25490 Although gliders come in an array of shapes and sizes, most gliders share basic design features. These include a fuselage, wings and components, lift/drag devices, and empennage. Depending on the launch method used, a glider may have a towhook or an engine.