Radar Vectors
Airworthiness Directive Current Issued Oct 26, 2015 5 pages Copy saved Nov 17, 2026

AD 2015-21-10 The Boeing Company Airplanes

We are superseding Airworthiness Directive (AD) 2015-19-03 for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and - 900ER series airplanes. AD 2015-19-03 required revising the maintenance or inspection program to include new airworthiness limitations. This AD continues to require a maintenance or inspection program revision, but with revised language. This AD was prompted by a determination that certain language in the airworthiness limitation was not accurate in AD 2015-19-03. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine, which could result in the inability to shut off fuel to the engine and, in case of certain engine fires, an uncontrollable fire that could lead to wing failure.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2015-4208; Directorate Identifier 2015-NM-152-AD; Amendment 39-18303; AD 2015-21-10] RIN 2120-AA64

Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

SUMMARY: We are superseding Airworthiness Directive (AD) 2015-19-03 for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and - 900ER series airplanes. AD 2015-19-03 required revising the maintenance or inspection program to include new airworthiness limitations. This AD continues to require a maintenance or inspection program revision, but with revised language. This AD was prompted by a determination that certain language in the airworthiness limitation was not accurate in AD 2015-19-03. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine, which could result in the inability to shut off fuel to the engine and, in case of certain engine fires, an uncontrollable fire that could lead to wing failure.

Dates

DATES: This AD is effective October 28, 2015.

We must receive any comments on this AD by December 10, 2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Addresses

• Fax: 202-493-2251.

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-4208; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Rebel Nichols, Aerospace Engineer, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6509; fax:

425-917-6590; email: [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

Discussion

On September 7, 2015, we issued AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. AD 2015-19-03 required revising the maintenance or inspection program to include new airworthiness limitations. AD 2015-19-03 resulted from reports of latently failed fuel shutoff valves discovered during fuel filter replacement. We issued AD 2015-19-03 to detect and correct latent failures of the fuel shutoff valve to the engine, which could result in the inability to shut off fuel to the engine and, in case of certain engine fires, an uncontrollable fire that could lead to wing failure.

Actions Since AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), Was Issued

Actions Since AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), Was Issued

Since we issued AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), we have determined that certain language in the airworthiness limitation was not accurate. In paragraph D. of the "Description" column of figure 1 to paragraph (g) of AD 2015-19-03, the "START LEVER" is identified as a "FUEL CONTROL switch" in four locations. In addition, in two locations in paragraph D. of the "Description" column of figure 1 to paragraph (g) of AD 2015-19-03, it specifies that fuel spar valve actuators are located in the "rear spar," but the correct location is the "front spar." Also, in two locations in paragraph D. of the "Description" column of figure 1 to paragraph (g) of AD 2015-19-03, the term "quadrant" is used to describe the control stand, but the correct terminology is "CONTROL STAND." We have determined that the language must be corrected to avoid any confusion in the paragraphs of the airworthiness limitation. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine, which could result in the inability to shut off fuel to the engine and, in case of certain engine fires, an uncontrollable fire that could lead to wing failure.

FAA's Determination

FAA's Determination

We are issuing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design.

AD Requirements

This AD requires revising the maintenance or inspection program to include new airworthiness limitations.

Interim Action

Interim Action

We consider this AD interim action. The manufacturer is currently developing a modification that will address the unsafe condition identified in this AD. Once this modification is developed, approved, and available, we might consider additional rulemaking.

FAA's Justification and Determination of the Effective Date

FAA's Justification and Determination of the Effective Date

We are superseding AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), to correct inaccurate terminology in paragraph D. of the "Description" column of figure 1 to paragraph (g) of AD 2015-19-03. We have made no other changes to the requirements published in AD 2015-19-03. We have determined that the changes impose no additional burden on any operator. Therefore, we find that notice and opportunity for prior public comment are unnecessary and that good cause exists for making this amendment effective in less than 30 days.

Comments Invited

Comments Invited

This AD is a final rule that involves requirements affecting flight safety, and we did not provide you with notice and an opportunity to provide your comments before it becomes effective. However, we invite you to send any written data, views, or arguments about this AD. Send your comments to an address listed under the ADDRESSES section. Include the Docket Number FAA-2015-4208 and Directorate Identifier 2015-NM-152-AD at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this AD. We will consider all comments received by the closing date and may amend this AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this AD.

Costs of Compliance

Costs of Compliance

We estimate that this AD affects 1,244 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Estimated Costs

Cost per Cost on U.S.

Action Labor cost Parts cost product operators

Incorporating Airworthiness Limitation 1 work-hour x $85 per $0 $85 $105,740

hour = $85.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a "significant regulatory action" under Executive Order 12866,

(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015), and adding the following new AD:

§ 39.13 [Amended]

2015-21-10 The Boeing Company: Amendment 39-18303; Docket No. FAA-2015-4208; Directorate Identifier 2015-NM-152-AD.

(a) Effective Date

This AD is effective October 28, 2015.

(b) Affected ADs

This AD replaces AD 2015-19-03, Amendment 39-18266 (80 FR 55527, September 16, 2015).

(c) Applicability

(c) Applicability

This AD applies to all The Boeing Company Model 737-600, -700, - 700C, -800, -900, and -900ER series airplanes, certificated in any category.

(d) Subject

Air Transport Association (ATA) of America Code 2823, Fuel Selector/Shutoff Valve.

(e) Unsafe Condition

This AD was prompted by reports of latently failed fuel shutoff valves discovered during fuel filter replacement. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine, which could result in the inability to shut off fuel to the engine and, in case of certain engine fires, an uncontrollable fire that could lead to wing failure.

(f) Compliance

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Revision of Maintenance or Inspection Program

Within 30 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to add airworthiness limitation number 28-AWL-MOV, "Engine Fuel Shutoff Valve (Fuel Spar Valve) Position Indication Operational Check," by incorporating the information specified in figure 1 to paragraph (g) of this AD into the Airworthiness Limitations Section of the Instructions for Continued Airworthiness. The initial compliance time for accomplishing the actions specified in 28-AWL-MOV is within 10 days after accomplishing the maintenance or inspection program revision required by this paragraph.

(g) Revision of Maintenance or Inspection Program

Figure 1 to Paragraph (g) of This AD--Engine Fuel Shutoff Valve (Fuel Spar Valve) Position Indication

Operational Check

AWL No. Task Interval Applicability Description

28-AWL-MOV … ALI DAILY … 737-600, -700, - Engine Fuel Shutoff

700C, -800, -900, Valve (Fuel Spar

and -900ER series Valve) Position

airplanes. Indication Operational

Check.

INTERVAL NOTE: The APPLICABILITY Concern: The fuel spar

operational check NOTE: Only valve actuator design

is not required on applies to can result in

days when the airplanes with a airplanes operating

airplane is not fuel spar valve with a failed fuel

used in revenue actuator having spar valve actuator

service. part number that is not reported.

The check must be MA20A2027 A latently failed fuel

done before (S343T003-56) or spar valve actuator

further flight MA30A1001 could prevent fuel

once the airplane (S343T003-66) shutoff to an engine.

is returned to installed at the In the event of

revenue service. engine fuel spar certain engine fires,

valve positions. the potential exists

for an engine fire to

be uncontrollable.

Perform one of the

following checks of

the engine fuel spar

valve position (unless

checked by the

flightcrew in a manner

approved by the

principal operations

inspector):

A. Operational Check

during engine

shutdown.

1. Do an operational

check of the left

engine fuel spar valve

actuator.

a. As the ENG 1 START

LEVER on the CONTROL

STAND is moved to the

CUTOFF position,

verify the SPAR VALVE

CLOSED indication

light on the OVERHEAD

PANEL for No.1 Engine

changes from OFF to

BRIGHT then DIM.

b. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing

Aircraft Maintenance

Manual (AMM) 28-22-

11).

2. Do an operational

check of the right

engine fuel spar valve

actuator.

a. As the ENG 2 START

LEVER on the CONTROL

STAND is moved to the

CUTOFF position,

verify the SPAR VALVE

CLOSED indication

light on the OVERHEAD

PANEL for No. 2 Engine

changes from OFF to

BRIGHT then DIM.

b. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM

28-22-11).

B. Operational check

during engine start.

1. Do an operational

check of the left

engine fuel spar valve

actuator.

a. As the ENG 1 START

LEVER on the CONTROL

STAND is moved to the

IDLE position, verify

the SPAR VALVE CLOSED

indication light on

the OVERHEAD PANEL for

No. 1 Engine changes

from DIM to BRIGHT

then OFF.

b. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM

28-22-11).

2. Do an operational

check of the right

engine fuel spar valve

actuator.

a. As the ENG 2 START

LEVER on the CONTROL

STAND is moved to the

IDLE position, verify

the SPAR VALVE CLOSED

indication light on

the OVERHEAD PANEL for

No. 2 Engine changes

from DIM to BRIGHT

then OFF.

b. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM

28-22-11).

C. Operational check

without engine

operation.

1. Supply electrical

power to airplane

using standard

practices.

2. Make sure No. 1 and

No. 2 Engine FIRE

switches on the Aft

Electronic Panel are

in the NORMAL (IN)

position.

3. Make sure No. 1 and

No. 2 Engine Start

Switches on the

Forward Overhead Panel

are in the OFF or AUTO

position.

4. Do an operational

check to the left

engine fuel spar valve

actuator.

a. Move ENG 1 START

LEVER on the CONTROL

STAND to the IDLE

position and wait

approximately 10

seconds.

NOTE: It is normal

under this test

condition for the ENG

VALVE CLOSED

indication light on

the OVERHEAD PANEL to

transition from DIM to

BRIGHT and stay

BRIGHT.

b. Move ENG 1 START

LEVER on the CONTROL

STAND to the CUTOFF

position.

c. Verify the SPAR

VALVE CLOSED

indication light on

the OVERHEAD PANEL for

No. 1 Engine changes

from OFF to BRIGHT

then DIM.

d. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM

28-22-11).

5. Do an operational

check of the right

engine fuel spar valve

actuator.

a. Move ENG 2 START

LEVER on the CONTROL

STAND to the IDLE

position and wait

approximately 10

seconds.

NOTE: It is normal

under this test

condition for the ENG

VALVE CLOSED

indication light on

the OVERHEAD PANEL to

transition from DIM to

BRIGHT and stay

BRIGHT.

b. Move ENG 2 START

LEVER on the CONTROL

STAND to the CUTOFF

position.

c. Verify the SPAR

VALVE CLOSED

indication light on

the OVERHEAD PANEL for

No.2 Engine changes

from OFF to BRIGHT

then DIM.

d. If the test fails

(bright light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM

28-22-11).

D. Perform an

inspection of the

engine fuel spar valve

actuator position.

NOTE: This inspection

may be used whenever

the SPAR VALVE light

does not function

properly.

1. Make sure the ENG 1

START LEVER on the

CONTROL STAND is in

the CUTOFF position.

NOTE: It is not

necessary to cycle the

START LEVER to do this

inspection.

2. Inspect the left

engine fuel spar valve

actuator located in

the left front spar.

NOTE: The left engine

fuel spar valve

actuator is on the

left wing front spar

outboard of the engine

strut. Access is

through access panel

521BB on the left wing

leading edge.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace

any engine fuel spar

valve actuator that is

not in the CLOSED

position (refer to

Boeing AMM 28-22-11).

3. Make sure the ENG 2

START LEVER on the

CONTROL STAND is in

the CUTOFF position.

NOTE: It is not

necessary to cycle the

START LEVER to do this

inspection.

4. Inspect the right

engine fuel spar valve

actuator located in

the right front spar.

NOTE: The right engine

fuel spar valve

actuator is on the

right wing front spar

outboard of the engine

strut. Access is

through access panel

621BB on the right

wing leading edge.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace

any engine fuel spar

valve actuator that is

not in the CLOSED

position (refer to

Boeing AMM 28-22-11).

(h) No Alternative Actions or Intervals

(h) No Alternative Actions or Intervals

After accomplishment of the maintenance or inspection program revision required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (i)(1) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

(i) Alternative Methods of Compliance (AMOCs)

(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected].

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(j) Related Information

(j) Related Information

For more information about this AD, contact Rebel Nichols, Aerospace Engineer, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6509; fax: 425-917-6590; email: [email protected].

(k) Material Incorporated by Reference

(k) Material Incorporated by Reference

None.

Issued in Renton, Washington, on October 16, 2015. Jeffrey E. Duven, Manager, Transport Airplane Directorate, Aircraft Certification Service.