Radar Vectors
Airworthiness Directive Current Issued Oct 26, 2015 6 pages Copy saved Nov 17, 2026

AD 2015-21-09 The Boeing Company Airplanes

We are superseding Airworthiness Directive (AD) 2015-19-02 for all The Boeing Company Model 767 airplanes. AD 2015-19-02 required revising the maintenance or inspection program to include new airworthiness limitations. This AD continues to require a maintenance or inspection program revision, but with revised language. This AD was prompted by a determination that certain language in the airworthiness limitation was not accurate in AD 2015-19-02. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine and auxiliary power unit (APU), which could result in the inability to shut off fuel to the engine and APU and, in case of certain fires, an uncontrollable fire that could lead to structural failure.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2015-4209; Directorate Identifier 2015-NM-156-AD; Amendment 39-18302; AD 2015-21-09] RIN 2120-AA64

Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

SUMMARY: We are superseding Airworthiness Directive (AD) 2015-19-02 for all The Boeing Company Model 767 airplanes. AD 2015-19-02 required revising the maintenance or inspection program to include new airworthiness limitations. This AD continues to require a maintenance or inspection program revision, but with revised language. This AD was prompted by a determination that certain language in the airworthiness limitation was not accurate in AD 2015-19-02. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine and auxiliary power unit (APU), which could result in the inability to shut off fuel to the engine and APU and, in case of certain fires, an uncontrollable fire that could lead to structural failure.

Dates

DATES: This AD is effective October 28, 2015.

We must receive any comments on this AD by December 10, 2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Addresses

• Fax: 202-493-2251.

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-4209; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Rebel Nichols, Aerospace Engineer, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6509; fax: 425-917-6590; email: [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

Discussion

On September 7, 2015, we issued AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), for all The Boeing Company Model 767 airplanes. AD 2015-19-02 required revising the maintenance or inspection program to include new airworthiness limitations. AD 2015-19-02 resulted from reports of latently failed fuel shutoff valves discovered during fuel filter replacement. We issued AD 2015-19-02 to detect and correct latent failures of the fuel shutoff valve to the engine and APU, which could result in the inability to shut off fuel to the engine and APU and, in case of certain fires, an uncontrollable fire that could lead to structural failure.

Actions Since AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), Was Issued

Actions Since AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), Was Issued

Since we issued AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), we have determined that extraneous language was included in two locations of the text of the airworthiness limitations specified in AD 2015-19-02. In paragraph C.7.a. of the "Description" column of figure 1 to paragraph (g) of AD 2015-19-02, the text "or the APU selector switch on the overhead panel is in the ON position" is not relevant to the actions specified in that paragraph. In paragraph A.5. of the "Description" column of figure 3 to paragraph (g) of AD 2015-19-02, the text "the FUEL CONTROL switch is in the RUN position or" is not relevant to the actions specified in that paragraph.

We have determined that the language must be corrected to avoid any confusion in the paragraphs of the airworthiness limitation. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine and APU, which could result in the inability to shut off fuel to the engine and APU and, in case of certain fires, an uncontrollable fire that could lead to structural failure.

FAA's Determination

FAA's Determination

We are issuing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design.

AD Requirements

This AD requires revising the maintenance or inspection program to include new airworthiness limitations.

Interim Action

Interim Action

We consider this AD interim action. The manufacturer is currently developing a modification that will address the unsafe condition identified in this AD. Once this modification is developed, approved, and available, we might consider additional rulemaking.

FAA's Justification and Determination of the Effective Date

FAA's Justification and Determination of the Effective Date

We are superseding AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), to correct inaccurate terminology in the "Description" column of figure 1 to paragraph (g) of AD 2015-19-02 and figure 3 to paragraph (g) of AD 2015-19-02. We have made no other changes to the requirements published in AD 2015-19-02. We have determined that the changes impose no additional burden on any operator. Therefore, we find that notice and opportunity for prior public comment are unnecessary and that good cause exists for making this amendment effective in less than 30 days.

Comments Invited

Comments Invited

This AD is a final rule that involves requirements affecting flight safety, and we did not provide you with notice and an opportunity to provide your comments before it becomes effective. However, we invite you to send any written data, views, or arguments about this AD. Send your comments to an address listed under the ADDRESSES section. Include the Docket Number FAA-2015-4209 and Directorate Identifier 2015-NM-156-AD at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this AD. We will consider all comments received by the closing date and may amend this AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this AD.

Costs of Compliance

Costs of Compliance

We estimate that this AD affects 450 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Estimated Costs

Cost per Cost on U.S.

Action Labor cost Parts cost product operators

Incorporating Airworthiness Limitation 1 work-hour x $85 per $0 $85 $38,250

hour = $85.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a "significant regulatory action" under Executive Order 12866,

(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015), and adding the following new AD:

§ 39.13 [Amended]

2015-21-09 The Boeing Company: Amendment 39-18302; Docket No. FAA-2015-4209; Directorate Identifier 2015-NM-156-AD.

(a) Effective Date

This AD is effective October 28, 2015.

(b) Affected ADs

This AD replaces AD 2015-19-02, Amendment 39-18265 (80 FR 55512, September 16, 2015).

(c) Applicability

(c) Applicability

This AD applies to all The Boeing Company Model 767-200, -300, - 300F, and -400ER series airplanes, certificated in any category.

(d) Subject

Air Transport Association (ATA) of America Code 28, Fuel.

(e) Unsafe Condition

This AD was prompted by reports of latently failed fuel shutoff valves discovered during fuel filter replacement. We are issuing this AD to detect and correct latent failures of the fuel shutoff valve to the engine and auxiliary power unit (APU), which could result in the inability to shut off fuel to the engine and APU and, in case of certain fires, an uncontrollable fire that could lead to structural failure.

(f) Compliance

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Revision of Maintenance or Inspection Program

Within 30 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to add airworthiness limitation numbers 28-AWL-ENG, 28-AWL-MOV, and 28-AWL-APU, by incorporating the information specified in figure 1, figure 2, and figure 3 to paragraph (g) of this AD into the Airworthiness Limitations Section of the Instructions for Continued Airworthiness. The initial compliance time for accomplishing the actions specified in figure 1, figure 2, and figure 3 to paragraph (g) of this AD is within 10 days after accomplishing the maintenance or inspection program revision required by this paragraph.

(g) Revision of Maintenance or Inspection Program

Figure 1 to Paragraph (g) of This AD: Engine Fuel Shutoff Valve (Fuel Spar Valve) Position Indication

Operational Check

AWL No. Task Interval Applicability Description

28-AWL-ENG … ALI DAILY … 767-200, -300, and - Engine Fuel Shutoff Valve

300F airplanes. (Fuel Spar Valve)

Position Indication

Operational Check.

INTERVAL NOTE: The APPLICABILITY NOTE: Concern: The fuel spar

operational check Applies to valve actuator design

is not required on airplanes with an can result in airplanes

days when the actuator installed operating with a failed

airplane is not at the engine fuel fuel spar valve actuator

used in revenue spar valve position that is not reported. A

service. having part number latently failed fuel

The check must be (P/N) MA20A2027 spar valve actuator

done before further (S343T003-56) or P/ could prevent fuel

flight once the N MA30A1001 shutoff to an engine. In

airplane is (S343T003-66). the event of certain

returned to revenue engine fires, the

service. potential exists for an

engine fire to be

uncontrollable.

Perform one of the

following checks/

inspection of the fuel

spar valve position

(unless checked by the

flightcrew in a manner

approved by the

principal operations

inspector):

A. Operational Check

during engine shutdown.

1. Do an operational

check of the left engine

fuel spar valve

actuator.

a. As the L FUEL CONTROL

switch on the quadrant

control stand is moved

to the CUTOFF position,

verify the left SPAR

VALVE disagreement light

on the quadrant control

stand illuminates and

then goes off.

b. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing

airplane maintenance

manual (AMM) 28-22-11).

2. Do an operational

check of the right

engine fuel spar valve

actuator.

a. As the R FUEL CONTROL

switch on the quadrant

control stand is moved

to the CUTOFF position,

verify the right SPAR

VALVE disagreement light

on the quadrant control

stand illuminates and

then goes off.

b. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM 28-

22-11).

B. Operational check

during engine start.

1. Do an operational

check of the left engine

fuel spar valve

actuator.

a. As the L FUEL CONTROL

switch on the quadrant

control stand is moved

to the RUN (or RICH)

position, verify the

left SPAR VALVE

disagreement light on

the quadrant control

stand illuminates and

then goes off.

b. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM 28-

22-11).

2. Do an operational

check of the right

engine fuel spar valve

actuator.

a. As the R FUEL CONTROL

switch on the quadrant

control stand is moved

to the RUN (or RICH)

position, verify the

right SPAR VALVE

disagreement light on

the quadrant control

stand illuminates and

then goes off.

b. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM 28-

22-11).

C. Operational check

without engine

operation.

1. Supply electrical

power to the airplane

using standard

practices.

2. Make sure all fuel

pump switches on the

Overhead Panel are in

the OFF position.

3. If the auxiliary power

unit (APU) is running,

open and collar the L

FWD FUEL BOOST PUMP

(C00372) circuit breaker

on the Main Power

Distribution Panel.

4. Make sure LEFT and

RIGHT ENG FIRE switches

on the Aft Aisle Stand

are in the NORMAL (IN)

position.

5. Make sure L and R ENG

START Selector Switches

on the Overhead Panel,

are in the OFF position.

6. Do an operational

check of the left engine

fuel spar valve

actuator.

a. Move L FUEL CONTROL

switch on the quadrant

control stand to the RUN

position and wait

approximately 10

seconds.

NOTE: It is normal under

this test condition for

the ENG VALVE

disagreement light on

the quadrant control

stand to stay

illuminated.

b. Move L FUEL CONTROL

switch on the quadrant

control stand to the

CUTOFF position.

c. Verify the left SPAR

VALVE disagreement light

on the quadrant control

stand illuminates and

then goes off.

d. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM 28-

22-11).

7. Do an operational

check of the right

engine fuel spar valve

actuator.

a. Move R FUEL CONTROL

switch on the quadrant

control stand to the RUN

position and wait

approximately 10 seconds

once the FUEL CONTROL

switch is in the RUN

position.

NOTE: It is normal under

this test condition for

the ENG VALVE

disagreement light on

the quadrant control

stand to stay

illuminated.

b. Move R FUEL CONTROL

switch on the quadrant

control stand to the

CUTOFF position.

c. Verify the right SPAR

VALVE disagreement light

on the quadrant control

stand illuminates and

then goes off.

d. If the test fails

(light fails to

illuminate), before

further flight, repair

faults as required

(refer to Boeing AMM 28-

22-11).

8. If the L FWD FUEL

BOOST PUMP circuit

breaker was collared in

step 3, remove collar

and close.

D. Perform an inspection

of the fuel spar valve

actuator position.

NOTE: This inspection may

be most useful whenever

the SPAR VALVE light

does not function

properly.

1. Make sure the L FUEL

CONTROL switch on the

quadrant control stand

is in the CUTOFF

position.

NOTE: It is not necessary

to cycle the FUEL

CONTROL switch to do

this inspection.

2. Inspect the left

engine fuel spar valve

actuator located in the

left rear spar.

NOTE: The Fuel Spar Valve

actuators are located

behind main gear doors

on the rear spar.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace any

fuel spar valve actuator

that is not in the

CLOSED position (refer

to Boeing AMM 28-22-11).

3. Make sure the R FUEL

CONTROL switch on the

quadrant control stand

is in the CUTOFF

position.

NOTE: It is not necessary

to cycle the FUEL

CONTROL switch to do

this inspection.

4. Inspect the right

engine fuel spar valve

actuator located in the

right rear spar.

NOTE: The Fuel Spar Valve

actuators are located

behind main gear doors

on the rear spar.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace any

fuel spar valve actuator

that is not in the

CLOSED position (refer

to Boeing AMM 28-22-11).

Figure 2 to Paragraph (g) of This AD: Engine Fuel Shutoff Valve (Fuel Spar Valve) Actuator Inspection

AWL No. Task Interval Applicability Description

28-AWL-MOV … ALI 10 DAYS … 767-400ER series Engine Fuel Shutoff Valve

airplanes. (Fuel Spar Valve)

Actuator Inspection.

INTERVAL NOTE: The APPLICABILITY NOTE: Concern: The fuel spar

inspection is not Applies to valve actuator design

required on days airplanes with an can result in airplanes

when the airplane actuator installed operating with a failed

is not used in at the engine fuel fuel spar valve actuator

revenue service. spar valve position that is not reported. A

The inspection must having part number latently failed fuel

be done before (P/N) MA20A2027 spar valve actuator

further flight if (S343T003-56) or P/ would prevent fuel

it has been 10 or N MA30A1001 shutoff to an engine. In

more calendar days (S343T003-66). the event of certain

since last engine fires, the

inspection. potential exists for an

engine fire to be

uncontrollable.

Perform an inspection of

the fuel spar valve

actuator position.

NOTE: The fuel spar valve

actuators are located

behind main gear doors

on the rear spar.

1. Make sure the L FUEL

CONTROL switch on the

quadrant control stand

is in the CUTOFF

position.

NOTE: It is not necessary

to cycle the FUEL

CONTROL switch to do

this inspection.

2. Inspect the left

engine fuel spar valve

actuator located in the

left rear spar.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace any

fuel spar valve actuator

that is not in the

CLOSED position (refer

to Boeing AMM 28-22-11).

3. Make sure the R FUEL

CONTROL switch on the

quadrant control stand

is in the CUTOFF

position.

NOTE: It is not necessary

to cycle the FUEL

CONTROL switch to do

this inspection.

4. Inspect the right

engine fuel spar valve

actuator located in the

right rear spar.

a. Verify the manual

override handle on the

engine fuel spar valve

actuator is in the

CLOSED position.

b. Repair or replace any

fuel spar valve actuator

that is not in the

CLOSED position (refer

to Boeing AMM 28-22-11).

Figure 3 to Paragraph (g) of This AD: Auxiliary Power Unit (APU) Fuel Shutoff Valve Position Indication

Operational Check

AWL No. Task Interval Applicability Description

28-AWL-APU … ALI 10 DAYS … ALL … APU Fuel Shutoff Valve

Position Indication

Operational Check.

INTERVAL NOTE: The APPLICABILITY NOTE: Concern: The APU fuel

operational check Applies to shutoff valve actuator

is not required on airplanes with an design can result in

days when the actuator installed airplanes operating with

airplane is not at the APU fuel a failed APU fuel

used in revenue shutoff valve shutoff valve actuator

service. The position having that is not reported. A

operational check part number (P/N) latently failed APU fuel

must be done before MA20A2027 (S343T003- shutoff valve actuator

further flight with 56) or MA30A1001 could prevent fuel

an operational APU (S343T003-66). shutoff to the APU. In

if it has been 10 the event of certain APU

or more calendar fires, the potential

days since last exists for an APU fire

check. to be uncontrollable

Perform the operational

check of the APU fuel

shutoff valve position

indication (unless

checked by the

flightcrew in a manner

approved by the

principal operations

inspector).

A. Do an operational

check of the APU fuel

shutoff valve position

indication.

1. If the APU is running,

unload and shut down the

APU using standard

practices.

2. Supply electrical

power to the airplane

using standard

practices.

3. Make sure the APU FIRE

switch on the Aft Aisle

Stand is in the NORMAL

(IN) position.

4. Make sure there is at

least 1,000 lbs (500

kgs) of fuel in the Left

Main Tank.

5. Move APU Selector

switch on the Overhead

Panel to the ON position

and wait approximately

10 seconds once the APU

selector switch on the

overhead panel is in the

ON position.

6. Move the APU Selector

switch on the Overhead

Panel to the OFF

position.

7. Verify the APU FAULT

light on the Overhead

Panel illuminates and

then goes off.

8. If the test fails

(light fails to

illuminate), before

further flight requiring

APU availability, repair

faults as required

(refer to Boeing AMM 28-

25-02).

NOTE: Dispatch may be

permitted per MMEL 28-25-

02 if APU is not

required for flight.

(h) No Alternative Actions or Intervals

(h) No Alternative Actions or Intervals

After accomplishment of the maintenance or inspection program revision required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (i)(1) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

(i) Alternative Methods of Compliance (AMOCs)

(1) The Manager, Seattle Aircraft Certification Office (ACO) FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected].

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(j) Related Information

(j) Related Information

For more information about this AD, contact Rebel Nichols, Aerospace Engineer, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6509; fax: 425-917-6590; email: [email protected].

(k) Material Incorporated by Reference

(k) Material Incorporated by Reference

None.

Issued in Renton, Washington, on October 16, 2015. Jeffrey E. Duven, Manager, Transport Airplane Directorate, Aircraft Certification Service.