Radar Vectors
Airworthiness Directive Current Issued Jun 8, 2010 3 pages Copy saved Nov 17, 2026

AD 2010-12-08 Airbus Model A300 Series Airplanes; Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes); and Model A310 Series Airplanes

We are adopting a new airworthiness directive (AD) for the

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2010-0171; Directorate Identifier 2009-NM-185-AD;

Amendment 39-16329; AD 2010-12-08]

RIN 2120-AA64

Airworthiness Directives; Airbus Model A300 Series Airplanes;

Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and

Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series

Airplanes); and Model A310 Series Airplanes

Agency

AGENCY: Federal Aviation Administration (FAA), Department of

Transportation (DOT).

ACTION: Final rule.

SUMMARY: We are adopting a new airworthiness directive (AD) for the

products listed above. This AD results from mandatory continuing

airworthiness information (MCAI) originated by an aviation authority of

another country to identify and correct an unsafe condition on an

another country to identify and correct an unsafe condition on an

aviation product. The MCAI describes the unsafe condition as:

During a maintenance check performed by an A310 operator, the

recommended modification of the lower attachment beam of rack 101VU

by accomplishment of Airbus Service Bulletin (SB) A310-53-2076 was

embodied on the aeroplane, leading the operator to find three cracks

embodied on the aeroplane, leading the operator to find three cracks

on the FR15A crossbeam above the NLG [nose landing gear] box at the

splicing with rack 107VU fitting.

This condition, if not detected and corrected, could degrade the

structural integrity of the crossbeam on NLG FR15A Web attachment

fitting of rack 107VU. Rack 107VU contains major airworthiness

fitting of rack 107VU. Rack 107VU contains major airworthiness

system components whose functioning could be adversely affected by

the loss of the attachment fitting.

As the A300 and A300-600 aeroplanes share this design feature,

they are also affected.

* * * * *

We are issuing this AD to require actions to correct the unsafe

We are issuing this AD to require actions to correct the unsafe

condition on these products.

DATES: This AD becomes effective July 13, 2010.

The Director of the Federal Register approved the incorporation by

reference of certain publications listed in this AD as of July 13,

2010.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of

Addresses

Transportation, Docket Operations, M-30, West Building Ground Floor,

Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer,

International Branch, ANM-116, Transport Airplane Directorate, FAA,

1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)

1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)

227-2125; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR

part 39 to include an AD that would apply to the specified products.

That NPRM was published in the Federal Register on February 25, 2010

(75 FR 8549). That NPRM proposed to correct an unsafe condition for the

(75 FR 8549). That NPRM proposed to correct an unsafe condition for the

specified products. The MCAI states:

During a maintenance check performed by an A310 operator, the

recommended modification of the lower attachment beam of rack 101VU

by accomplishment of Airbus Service Bulletin (SB) A310-53-2076 was

embodied on the aeroplane, leading the operator to find three cracks

on the FR15A crossbeam above the NLG [nose landing gear] box at the

on the FR15A crossbeam above the NLG [nose landing gear] box at the

splicing with rack 107VU fitting.

This condition, if not detected and corrected, could degrade the

structural integrity of the crossbeam on NLG FR15A Web attachment

fitting of rack 107VU. Rack 107VU contains major airworthiness

system components whose functioning could be adversely affected by

system components whose functioning could be adversely affected by

the loss of the attachment fitting.

As the A300 and A300-600 aeroplanes share this design feature,

they are also affected.

For the reasons stated above, this AD requires repetitive

inspections for cracks of the crossbeam on NLG FR15A Web face

attachment fitting of rack 107VU and corrective action, depending on

attachment fitting of rack 107VU and corrective action, depending on

findings.

The corrective actions include contacting Airbus for repair

instructions, and doing the repair if any crack is found. You may

obtain further information by examining the MCAI in the AD docket.

Comments

Comments

We gave the public the opportunity to participate in developing

this AD. We considered the comment received. The commenter, FedEx

Express, supports the NPRM.

Explanation of Change Made to This AD

We have revised the subject header of this AD to identify the

affected airplane models as published in the most recent type

affected airplane models as published in the most recent type

certificate data sheet.

Conclusion

We reviewed the available data, including the comment received, and

determined that air safety and the public interest require adopting the

AD as proposed.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in

general, agree with their substance. But we might have found it

general, agree with their substance. But we might have found it

necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these

changes, we do not intend to differ substantively from the information

provided in the MCAI and related service information.

changes, we do not intend to differ substantively from the information

We might also have required different actions in this AD from those

in the MCAI in order to follow our FAA policies. Any such differences

are highlighted in a Note within the AD.

Costs of Compliance

We estimate that this AD will affect 206 products of U.S. registry.

We also estimate that it will take about 2 work-hours per product to

comply with the basic requirements of this AD. The average labor rate

comply with the basic requirements of this AD. The average labor rate

is $85 per work-hour. Based on these figures, we estimate the cost of

this AD to the U.S. operators to be $35,020, or $170 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to

issue rules on aviation safety. Subtitle I, section 106, describes the

issue rules on aviation safety. Subtitle I, section 106, describes the

authority of the FAA Administrator. "Subtitle VII: Aviation

Programs," describes in more detail the scope of the Agency's

authority.

We are issuing this rulemaking under the authority described in

"Subtitle VII, Part A, Subpart III, Section 44701: General

requirements." Under that section, Congress charges the FAA with

requirements." Under that section, Congress charges the FAA with

promoting safe flight of civil aircraft in air commerce by prescribing

regulations for practices, methods, and procedures the Administrator

finds necessary for safety in air commerce. This regulation is within

the scope of that authority because it addresses an unsafe condition

that is likely to exist or develop on products identified in this

that is likely to exist or develop on products identified in this

rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications

under Executive Order 13132. This AD will not have a substantial direct

effect on the States, on the relationship between the national

government and the States, or on the distribution of power and

government and the States, or on the distribution of power and

responsibilities among the various levels of government.

For the reasons discussed above, I certify this AD:

1. Is not a "significant regulatory action" under Executive Order

12866;

2. Is not a "significant rule" under the DOT Regulatory Policies

and Procedures (44 FR 11034, February 26, 1979); and

and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or

negative, on a substantial number of small entities under the criteria

of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to

negative, on a substantial number of small entities under the criteria

comply with this AD and placed it in the AD docket.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office

between 9 a.m. and 5 p.m., Monday through Friday, except Federal

holidays. The AD docket contains the NPRM, the regulatory evaluation,

any comments received, and other information. The street address for

any comments received, and other information. The street address for

the Docket Operations office (telephone (800) 647-5527) is in the

ADDRESSES section. Comments will be available in the AD docket shortly

after receipt.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

List of Subjects in 14 CFR Part 39

reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator,

the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

§ 39.13 [Amended]

2. The FAA amends § 39.13 by adding the following new AD:

2010-12-08 Airbus: Amendment 39-16329. Docket No. FAA-2010-0171;

Directorate Identifier 2009-NM-185-AD.

Effective Date

(a) This airworthiness directive (AD) becomes effective July 13,

2010.

Affected ADs

(b) None.

Applicability

Applicability

(c) This AD applies to all Airbus Model A300 B2-1A, B2-1C, B2K-

3C, B2-203, B4-2C, B4-103, B4-203, B4-601, B4-603, B4-620, B4-622,

B4-605R, B4-622R, F4-605R, and F4-622R airplanes; Model C4-605R

Variant F airplanes; and Model A310-203, -204, -221, -222, -304, -

322, -324, and -325 airplanes; certificated in any category.

Subject

Subject

(d) Air Transport Association (ATA) of America Code 53:

Fuselage.

Reason

(e) The mandatory continuing airworthiness information (MCAI)

states:

During a maintenance check performed by an A310 operator, the

recommended modification of the lower attachment beam of rack 101VU

by accomplishment of Airbus Service Bulletin (SB) A310-53-2076 was

by accomplishment of Airbus Service Bulletin (SB) A310-53-2076 was

embodied on the aeroplane, leading the operator to find three cracks

on the FR15A crossbeam above the NLG [nose landing gear] box at the

splicing with rack 107VU fitting.

This condition, if not detected and corrected, could degrade the

structural integrity of the crossbeam on NLG FR15A Web attachment

structural integrity of the crossbeam on NLG FR15A Web attachment

fitting of rack 107VU. Rack 107VU contains major airworthiness

system components whose functioning could be adversely affected by

the loss of the attachment fitting.

As the A300 and A300-600 aeroplanes share this design feature,

system components whose functioning could be adversely affected by

they are also affected.

For the reasons stated above, this AD requires repetitive

inspections for cracks of the crossbeam on NLG FR15A Web face

attachment fitting of rack 107VU and corrective action, depending on

findings.

The corrective actions include contacting Airbus for repair

The corrective actions include contacting Airbus for repair

instructions, and doing the repair if any crack is found.

Compliance

(f) You are responsible for having the actions required by this

AD performed within the compliance times specified, unless the

actions have already been done.

Actions

(g) Do the following actions.

(1) At the later of the times specified in paragraphs (g)(1)(i)

and (g)(1)(ii) of this AD: Do a detailed inspection for cracks of

and (g)(1)(ii) of this AD: Do a detailed inspection for cracks of

the crossbeam on the nose landing gear FR15A Web attachment fitting

of rack 107VU, in accordance with the Accomplishment Instructions in

the applicable service bulletin specified in Table 1 of this AD.

(i) Before the accumulation of 6,600 total flight cycles.

of rack 107VU, in accordance with the Accomplishment Instructions in

(ii) Within 2,300 flight cycles or 30 months after the effective

date of this AD, whichever occurs first.

(2) Thereafter, at intervals not to exceed 2,300 flight cycles,

repeat the inspection specified in paragraph (g)(1) of this AD.

Table 1--Service Bulletins

Model Service bulletin Date

Airbus Model A300 series Airbus Mandatory March 17, 2009.

airplanes. Service Bulletin

A300-53-0388,

including Appendix

01.

Airbus Model 300-600 series Airbus Mandatory March 17, 2009.

airplanes. Service Bulletin

A300-53-6164,

including Appendix

01.

Airbus Model A310 series Airbus Mandatory March 17, 2009.

airplanes. Service Bulletin

A310-53-2131,

including Appendix

01.

(3) If any crack is found during any inspection required by

paragraphs (g)(1) and (g)(2) of this AD, before further flight

paragraphs (g)(1) and (g)(2) of this AD, before further flight

contact Airbus for approved repair instructions and do the repair.

(4) Submit an inspection report of the inspection required by

paragraph (g)(1) of this AD to Airbus Customer Services Directorate,

1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France;

telephone +33 5 61 93 33 33; fax +33 5 61 93 28 06; e-mail

telephone +33 5 61 93 33 33; fax +33 5 61 93 28 06; e-mail

[email protected]; at the applicable time specified in

paragraph (g)(4)(i) or (g)(4)(ii) of this AD. The report must

include the information specified on the inspection report sheet

provided in Appendix 01 of the applicable service bulletin

provided in Appendix 01 of the applicable service bulletin

identified in Table 1 of this AD.

(i) If the inspection was done on or after the effective date of

this AD: Submit the report within 30 days after the inspection.

(ii) If the inspection was done before the effective date of

this AD: Submit the report within 30 days after the effective date

this AD: Submit the report within 30 days after the effective date

of this AD.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information

as follows: No differences.

Other FAA AD Provisions

(h) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager,

International Branch, ANM-116, FAA, has the authority to approve

AMOCs for this AD, if requested using the procedures found in 14 CFR

AMOCs for this AD, if requested using the procedures found in 14 CFR

39.19. Send information to Attn: Dan Rodina, Aerospace Engineer,

International Branch, ANM-116, Transport Airplane Directorate, FAA,

1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone

(425) 227-2125; fax (425) 227-1149. Before using any approved AMOC

on any airplane to which the AMOC applies, notify your principal maintenance inspector

on any airplane to which the AMOC applies, notify your principal maintenance inspector

(PMI) or principal avionics inspector (PAI), as appropriate, or

lacking a principal inspector, your local Flight Standards District

Office. The AMOC approval letter must specifically reference this

Office. The AMOC approval letter must specifically reference this

AD.

(2) Airworthy Product: For any requirement in this AD to obtain

corrective actions from a manufacturer or other source, use these

actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product

(or their delegated agent). You are required to assure the product

is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in

this AD, under the provisions of the Paperwork Reduction Act (44

U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has

approved the information collection requirements and has assigned

approved the information collection requirements and has assigned

OMB Control Number 2120-0056.

Related Information

(i) Refer to MCAI European Aviation Safety Agency Airworthiness

Directive 2009-0165, dated July 31, 2009, and the service

information specified in Table 1 of this AD, for related

information.

Material Incorporated by Reference

(j) You must use the applicable service information contained in

Table 2 of this AD to do the actions required by this AD, unless the

Table 2 of this AD to do the actions required by this AD, unless the

AD specifies otherwise.

(1) The Director of the Federal Register approved the

incorporation by reference of this service information under 5

U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact

Airbus SAS--EAW (Airworthiness Office), 1 Rond Point Maurice

Airbus SAS--EAW (Airworthiness Office), 1 Rond Point Maurice

Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96;

fax +33 5 61 93 44 51; e-mail [email protected];

Internet http://www.airbus.com.

(3) You may review copies of the service information at the FAA,

Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,

Washington. For information on the availability of this material at

Washington. For information on the availability of this material at

the FAA, call 425-227-1221.

(4) You may also review copies of the service information that

is incorporated by reference at the National Archives and Records

Administration (NARA). For information on the availability of this

Administration (NARA). For information on the availability of this

material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Table 2--Material Incorporated by Reference

Document Date

Airbus Mandatory Service Bulletin A300- March 17, 2009.

53-0388, including Appendix 01.

Airbus Mandatory Service Bulletin A300- March 17, 2009.

53-6164, including Appendix 01.

Airbus Mandatory Service Bulletin A310- March 17, 2009.

53-2131, including Appendix 01.

Issued in Renton, Washington, on May 28, 2010.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification

Manager, Transport Airplane Directorate, Aircraft Certification

Service.