Radar Vectors
Airworthiness Directive Current Issued Nov 3, 2009 4 pages Copy saved Nov 17, 2026

AD 2009-23-01 Hawker Beechcraft Corporation Model 1900, 1900C, and 1900D Airplanes

We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Models 1900, 1900C, and 1900D airplanes. This AD requires a one-time visual inspection and repetitive ultrasonic inspections of the left and right main landing gear (MLG) actuators for leaking and/or cracks with replacement of the actuator if leaking and/ or cracks are found. This AD results from reports of leaking and cracked actuators. We are issuing this AD to detect and correct leaking and cracks in the MLG actuators, which could result in loss of hydraulic fluid. This condition could lead to an inability to extend or lock down the landing gear, which could result in a gear up landing or a gear collapse on landing.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2008-1312; Directorate Identifier 2008-CE-065-AD; Amendment 39-16072; AD 2009-23-01] RIN 2120-AA64

Airworthiness Directives; Hawker Beechcraft Corporation Model 1900, 1900C, and 1900D Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

Summary

SUMMARY: We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Models 1900, 1900C, and 1900D airplanes. This AD requires a one-time visual inspection and repetitive ultrasonic inspections of the left and right main landing gear (MLG) actuators for leaking and/or cracks with replacement of the actuator if leaking and/ or cracks are found. This AD results from reports of leaking and cracked actuators. We are issuing this AD to detect and correct leaking and cracks in the MLG actuators, which could result in loss of hydraulic fluid. This condition could lead to an inability to extend or lock down the landing gear, which could result in a gear up landing or a gear collapse on landing.

Dates

DATES: This AD becomes effective on December 8, 2009.

On December 8, 2009, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD.

ADDRESSES: To get the service information identified in this AD, contact Hawker Beechcraft Corporation, P.O. Box 85, Wichita, Kansas 67201-0085; telephone: (800) 429-5372 or (316) 676-3140; Internet: http://pubs.hawkerbeechcraft.com.

Addresses

To view the AD docket, go to U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, or on the Internet at http://www.regulations.gov. The docket number is FAA-2008-1312; Directorate Identifier 2008-CE-065-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Don Ristow, Aerospace Engineer, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: (316) 946-4120; fax: (316) 946-4107.

SUPPLEMENTARY INFORMATION:

Discussion

On August 20, 2009, we issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain Hawker Beechcraft Corporation Models 1900, 1900C, and 1900D airplanes. This proposal was published in the Federal Register as a supplemental notice of proposed rulemaking (NPRM) on August 31, 2009 (74 FR 44773). The NPRM proposed to require a one-time visual inspection and repetitive ultrasonic inspections of the left and right main landing gear (MLG) actuators for leaking and/or cracks with replacement of the actuator if leaking and/or cracks are found.

Comments

Comments

We provided the public the opportunity to participate in developing this AD. The following presents the comment received on the proposal and FAA's response to the comment:

Comment Issue: Superseding Previous ADs

Hawker Beechcraft Corporation requests that with this AD action we supersede AD 99-04-08 and AD 97-26-15, which affect earlier configurations of part number 114-380041 MLG actuator. They believe that one AD correcting all of the unsafe conditions concerned with the MLG actuator would eliminate confusion concerning which AD to comply with.

Comment Issue: Superseding Previous ADs

The FAA disagrees. We did consider supersedure of the previous two ADs, AD 99-04-08 and AD 97-26-15. The previous two ADs and this new AD action each address different unsafe conditions on the MLG actuators. AD 99-04-08 concerns lubrication and replacement of the rod end, and AD 97-26-15 concerns replacement of the actuator head end cap. This new AD action concerns replacement of the rod end cap. AD 99-04-08 uses a prorated time of compliance starting with actuators that have accumulated 6,000 hours time-in-service and may still apply to low usage aircraft or aircraft that have been in storage. This current AD action specifies compliance based on actuator cycles. The only common feature in the three ADs is that the actuators were manufactured by Frisby Airborne Hydraulic, Inc.

Based on the differences in the two previous ADs and in this new AD, we determined that combining the three into a single AD would confuse the unsafe conditions, rather than simplify them. If combined into one AD, each unsafe condition would still have different inspections, different replacements, and different compliance times. To incorporate those differences into a single AD would create a complicated AD to understand. By keeping the AD actions separate, the corrective actions for each unsafe condition can be complied with individually. For these reasons, we decided a new AD action would be appropriate.

We will not change the final rule AD action based on this comment.

Conclusion

Conclusion

We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial corrections. We have determined that these minor corrections:

• Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and

• Do not add any additional burden upon the public than was already proposed in the NPRM.

Costs of Compliance

Costs of Compliance

We estimate that this AD affects 300 airplanes in the U.S. registry.

The ultrasonic inspection includes the time allowed for removing and reinstalling the actuator. We estimate the following costs to do the inspections:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

Visual Inspection: .5 work-hour x $80 per hour Not applicable … $40 $12,000

= $40.

Ultrasonic Inspection: 6 work-hours x $80 per Not applicable … 480 144,000

hour = $480 (If the mechanic does not remove the actuator for the ultrasonic inspection, the labor cost will be less.).

We estimate the following costs to do any necessary replacements that would be required based on the results of the inspections. We have no way of determining the number of airplanes that may need this replacement:

Total cost per

Labor cost Parts cost airplane

6 work-hours x $80 per hour = $480 $4,600 per actuator. $5,080

(If the mechanic removes the actuator for the ultrasonic inspection, then the labor cost will be less.).

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this AD.

Regulatory Findings

Regulatory Findings

We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this AD (and other information as included in the Regulatory Evaluation) and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "Docket No. FAA-2008-1312; Directorate Identifier 2008-CE-065-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding a new AD to read as follows:

2009-23-01 Hawker Beechcraft Corporation: Amendment 39-16072; Docket No. FAA-2008-1312; Directorate Identifier 2008-CE-065-AD.

Effective Date

Effective Date

(a) This AD becomes effective on December 8, 2009.

Affected ADs

(b) None.

Applicability

(c) This AD applies to the airplane models and serial numbers listed below that are certificated in any category and equipped with a Hawker Beechcraft part number (P/N) 114-380041-11 (or FAA-approved equivalent P/N), 114-380041-13 (or FAA-approved equivalent P/N), 114-380041-15 (or FAA-approved equivalent P/N), or 114-380041-15OVH main landing gear (MLG) actuator. For the purposes of this AD action the phrase "or FAA-approved equivalent part number" in this AD refers to any PMA part that is approved by identicality to the referenced part. Frisby Airborne Hydraulic, Inc. (Frisby) P/N 1FA10043-3 has parts manufacturer approval (PMA) by identicality to P/N 114-380041-15; therefore, it is considered an FAA-approved equivalent P/N and the AD applies to airplanes with this part installed.

Applicability

Models Serial Nos.

(1) 1900 … UA-3.

(2) 1900C … UB-1 through UB-74, UC-1 through UC-174, and UD-1

through UD-6.

(3) 1900D … UE-1 through UE-439.

Unsafe Condition

(d) This AD results from reports of leaking and cracked actuators. We are issuing this AD to detect and correct leaking and cracks in the MLG actuators, which could result in loss of hydraulic fluid. This condition could lead to an inability to extend or lock down the landing gear, which could result in a gear up landing or a gear collapse on landing.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Note: The phrase "or FAA-approved equivalent part number" in this AD refers to any PMA part that is approved by identicality to the referenced part.

Actions Compliance Procedures

(1) Do a one-time visual Within the next 50 hours (i) For Hawker

inspection of the MLG time-in-service after Beechcraft

actuator for cracks. December 8, 2009 (the parts: Follow

effective date of this Hawker

AD) or within the next 30 Beechcraft

days after December 8, Mandatory

2009 (the effective date Service

of this AD), whichever Bulletin SB 32-

occurs later. 3870, dated

April 2008.

(ii) For PMA by

identicality:

Either contact

the aircraft

certification

office (ACO)

using the

contact

information in

paragraph

(g)(1) of this

AD for FAA-

approved

procedures

provided by the

PMA holder; or

install Hawker

Beechcraft

parts and

follow Hawker

Beechcraft

Mandatory

Service

Bulletin SB 32-

3870, dated

April 2008, and

follow any

inspection

required by

this AD.

(2) Do an initial Initially within the next (A) For Hawker

ultrasonic inspection of 600 cycles after December Beechcraft

the MLG actuator. 8, 2009 (the effective parts: Follow

date of this AD) or Hawker

within the next 3 months Beechcraft

after December 8, 2009 Mandatory

(the effective date of Service

this AD), whichever Bulletin SB 32-

occurs first. 3870, dated

(i) For those airplanes April 2008.

with overhauled MLG (B) For PMA by

actuators (with less than identicality:

1,200 cycles) that have Either contact

records that prove an the ACO using

internal fluorescent the contact

penetrant inspection has information in

been done, you may do the paragraph

initial ultrasonic (g)(1) of this

inspection within the AD for FAA-

next 600 cycles after approved

December 8, 2009 (the procedures

effective date of this provided by the

AD) or within the next PMA holder; or

1,200 cycles since the install Hawker

last overhaul, whichever Beechcraft

occurs later. parts and

(ii) For those airplanes follow Hawker

with MLG actuators with Beechcraft

less than 8,000 cycles Mandatory

since new or MLG Service

actuators that have Bulletin SB 32-

records that prove the 3870, dated

end caps are new (less April 2008, and

than 8,000 cycles), you follow any

may do the initial inspection

ultrasonic inspection required by

within the next 1,200 this AD.

cycles after December 8,

2009 (the effective date

of this AD) or upon

accumulation of 8,000

cycles since the end caps

were new, whichever

occurs later. (3) For all airplanes, do Repetitively at intervals (i) For Hawker

repetitive ultrasonic not to exceed every 1,200 Beechcraft

inspections of the MLG cycles since the last parts: Follow

actuator. ultrasonic inspection. Hawker

Beechcraft

Mandatory

Service

Bulletin SB 32-

3870, dated

April 2008.

(ii) For PMA by

identicality:

Either contact

the ACO using

the contact

information in

paragraph

(g)(1) of this

AD for FAA-

approved

procedures

provided by the

PMA holder; or

install Hawker

Beechcraft

parts and

follow Hawker

Beechcraft

Mandatory

Service

Bulletin SB 32-

3870, dated

April 2008, and

follow any

inspection

required by

this AD.

(4) If cracks are found Before further flight (A) For Hawker

during any inspection after the inspection Beechcraft

required in paragraph where the cracks are parts: Follow

(e)(1), (e)(2), and found. Hawker

(e)(3) of this AD, Beechcraft

replace the MLG actuator Mandatory

with one of the Service

following: Bulletin SB 32-

(i) MLG actuator P/N 114- 3870, dated

380041-15 (or FAA- April 2008.

approved equivalent P/N) (B) For PMA by

or 114-380041-15OVH that identicality:

is new or has been Either contact

inspected following the ACO using

paragraphs (e)(1), the contact

(e)(2), and (e)(3) of information in

this AD and has been paragraph

found to not have cracks; (g)(1) of this

or AD for FAA-

(ii) An FAA-approved approved

actuator. Installation of procedures

an MLG actuator P/N other provided by the

than 114-380041-11 (or PMA holder; or

FAA-approved equivalent P/ install Hawker

N), 114-380041-13 (or FAA- Beechcraft

approved equivalent P/N), parts and

114-380041-15 (or FAA- follow Hawker

approved equivalent P/N), Beechcraft

or 114-380041-15OVH Mandatory

terminates the inspection Service

requirements of Bulletin SB 32-

paragraphs (e)(1), 3870, dated

(e)(2), and (e)(3) of April 2008, and

this AD. follow any

inspection

required by

this AD.

(5) Do not install any MLG As of December 8, 2009 Not applicable.

actuator P/N 114-380041- (the effective date of

11 (or FAA-approved this AD).

equivalent P/N) or 114-380041-13 (or FAA-approved equivalent P/N).

(f) If the number of cycles is unknown, calculate the compliance times of cycles in this AD by using hours time-in-service (TIS). Multiply the number of hours TIS on the MLG actuator by 4 to come up with the number of cycles. For the purposes of this AD:

(1) 600 cycles equals 150 hours' TIS; and

(2) 1,200 cycles equals 300 hours' TIS.

(g) If cracks are found during any inspection required in paragraphs (e)(1), (e)(2), or (e)(3) of this AD, report the size and location of the cracks to the FAA within 10 days after the cracks are found or within 10 days after December 8, 2009 (the effective date of this AD), whichever occurs later.

(1) Send report to Don Ristow, Aerospace Engineer, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; e-mail: [email protected].

(2) The Office of Management and Budget (OMB) approved the information collection requirements contained in this regulation under the provisions of the Paperwork Reduction Act of 1980 (44 U.S.C. 3501 et seq.) and assigned OMB Control Number 2120-0056.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(h) The Manager, Wichita Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Don Ristow, Aerospace Engineer, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: (316) 946-4120; fax: (316) 946-4107. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

Material Incorporated by Reference

Material Incorporated by Reference

(i) You must use Hawker Beechcraft Mandatory Service Bulletin SB 32-3870, dated April 2008, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact Hawker Beechcraft Corporation, P.O. Box 85, Wichita, Kansas 67201-0085; telephone: (800) 429-5372 or (316) 676-3140; Internet: http://pubs.hawkerbeechcraft.com.

(3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329-3768.

(4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Issued in Kansas City, Missouri, on October 23, 2009. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.