Radar Vectors
Airworthiness Directive Current Issued Apr 19, 2010 4 pages Copy saved Nov 17, 2026

AD 2009-08-05R1 Liberty Aerospace Incorporated Model XL-2 Airplanes

We are correcting the address, telephone, and fax information for the reporting requirement in Airworthiness Directive (AD) 2009-08-05, which applies to certain Liberty Aerospace Incorporated Model XL-2 airplanes. AD 2009-08-05 currently requires repetitively inspecting the exhaust muffler for cracks, replacing the exhaust muffler when cracks are found, and reporting the results of the inspections to the FAA. Since AD 2009-08-05 became effective, the FAA's Atlanta Aircraft Certification Office (ACO) moved, which has caused the office personnel problems in receiving fax and mailed copies of the inspection result reports. This document corrects the mailing address, telephone number, and fax information of the Atlanta ACO.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2009-0329; Directorate Identifier 2009-CE-020-AD; Amendment 39-16264; AD 2009-08-05 R1] RIN 2120-AA64

Airworthiness Directives; Liberty Aerospace Incorporated Model XL-2 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

Action

ACTION: Final rule.

SUMMARY: We are correcting the address, telephone, and fax information for the reporting requirement in Airworthiness Directive (AD) 2009-08-05, which applies to certain Liberty Aerospace Incorporated Model XL-2 airplanes. AD 2009-08-05 currently requires repetitively inspecting the exhaust muffler for cracks, replacing the exhaust muffler when cracks are found, and reporting the results of the inspections to the FAA. Since AD 2009-08-05 became effective, the FAA's Atlanta Aircraft Certification Office (ACO) moved, which has caused the office personnel problems in receiving fax and mailed copies of the inspection result reports. This document corrects the mailing address, telephone number, and fax information of the Atlanta ACO.

Dates

DATES: This final rule is effective April 19, 2010. The compliance date of this AD is April 20, 2009, which is the same as the effective date of AD 2009-08-05.

As of April 20, 2009 (74 FR 16117, April 9, 2009), the Director of the Federal Register approved the incorporation by reference of Liberty Aerospace, Inc. Service Document Critical Service Bulletin (CSB) CSB-09-001, Revision Level B, Revised on March 18, 2009.

Addresses

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT:

--Corey Spiegel, Aerospace Engineer, Atlanta Aircraft Certification Office, 1701 Columbia Avenue, College Park, Georgia 30337; telephone: (404) 474-5574; facsimile: (404) 474-5606; e-mail: [email protected]; or --Cindy Lorenzen, Aerospace Engineer, Atlanta Aircraft Certification Office, 1701 Columbia Avenue, College Park, Georgia 30337; telephone: (404) 474-5524; facsimile: (404) 474-5606; e-mail: [email protected].

Supplementary Information

SUPPLEMENTARY INFORMATION:

Discussion

On April 3, 2009, we issued AD 2009-08-05, Amendment 39-15878 (74 FR 16117, April 9, 2009), to require repetitively inspecting the exhaust muffler for cracks, replacing the exhaust muffler when cracks are found, and reporting the results of the inspections to the FAA.

Discussion

Since AD 2009-08-05 became effective, the FAA's Atlanta Aircraft Certification Office (ACO) moved, which has caused the office personnel problems in receiving fax and mailed copies of the inspection result reports.

Consequently, the FAA sees a need to correct the mailing address, telephone number, and fax information of the Atlanta ACO in AD 2009-08-05 to assure that the inspection results are received and reviewed to help assure the continued operational safety of the affected airplanes. Thus, the FAA is revising the AD to incorporate the language discussed above and to add the amendment to section 39.13 of the Federal Aviation Regulations (14 CFR 39.13).

Since this action only corrects the address, telephone number, and fax information for the reporting requirement and does not require any additional actions over that originally required by AD 2009-08-05, it has no adverse economic impact and imposes no additional burden on any person than was already required. Therefore, the FAA has determined that prior notice and opportunity for public comment are unnecessary.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2009-08-05, Amendment 39-15878 (74 FR 16117, April 9, 2009), and adding the following new AD:

§ 39.13 [Amended]

2009-08-05 R1 Liberty Aerospace Incorporated: Amendment 39-16264; Docket No. FAA-2009-0329; Directorate Identifier 2009-CE-020-AD.

Effective Date

(a) This final rule is effective April 19, 2010. The compliance date of this AD is April 20, 2009, which is the same as the effective date of AD 2009-08-05.

Affected ADs

Affected ADs

(b) This AD revises AD 2009-08-05.

Applicability

(c) This AD applies to Model XL-2 airplanes, serial numbers 0007, 0009, and subsequent, that are certificated in any category.

Unsafe Condition

(d) This AD is the result of reports that eight cracks have been found in the exhaust muffler during maintenance and service inspections. We are issuing this AD to detect and correct cracks in the exhaust muffler, which could result in carbon monoxide entering the cabin heating system. This condition could lead to incapacitation of the pilot.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Actions Compliance Procedures

(1) Inspect the following: Initially inspect within the next 10 Follow Liberty Aerospace, Inc.

(i) The exhaust muffler for cracks. hours time-in-service (TIS) after Service Document Critical Service

There are two different exhaust April 20, 2009 (the effective date Bulletin (CSB) CSB-09-001, Revision

systems available for the affected of AD 2009-08-05) or at the next Level B, Revised on March 18, 2009.

airplanes. They are: annual inspection, whichever occurs

(A) Standard exhaust system, part first. Repetitively inspect the

number (P/N) DEL200201-002 that exhaust muffler thereafter as

incorporates muffler P/N DEL200201- specified in paragraph (e)(5) of

incorporates muffler P/N DEL200201- specified in paragraph (e)(5) of

101; and this AD.

(B) Reduced sound exhaust

system, P/N DEL200201-003

that incorporates muffler P/

N 200201-104.

(ii) The tail pipe and the tail

pipe opening in the lower cowl

for a 0.5-inch minimum

clearance.

(iii) Inspect the propeller for

proper propeller clocking

position.

(2) As a result of the inspections Before further flight after the As specified in Liberty Aerospace,

required in paragraphs (e)(1)(ii) inspection required in paragraph Inc. Service Document Critical

and (e)(1)(iii) of this AD: (e)(1) of this AD. Service Bulletin (CSB) CSB-09-001,

(i) If the clearance between the Revision Level B, Revised on March

tail pipe and the tail pipe opening 18, 2009.

is less than the required 0.5-inch minimum, trim the lower cowl as needed to achieve the minimum clearance.

(ii) If there is a discrepancy

in the propeller clocking

position, remove and reinstall

the propeller at the correct

position.

(3) As a result of the initial Before further flight after the Follow Liberty Aerospace, Inc.

inspection required in paragraph initial inspection required in Service Document Critical Service

(e)(1)(i) of this AD or any paragraph (e)(1) of this AD and Bulletin (CSB) CSB-09-001, Revision

repetitive inspection required in before further flight after any Level B, Revised on March 18, 2009.

paragraph (e)(5) of this AD, if a repetitive inspection required in

crack is found, replace the exhaust paragraph (e)(5) of this AD. muffler. (i) The manufacturer will provide the replacement exhaust system.

(ii) A reduced sound exhaust

system may be replaced with a

standard exhaust system.

(iii) Installing a reduced sound

exhaust system as a replacement

part also requires installing a

bypass SCAT tube and a "Do Not

Use" placard on or near the

heater knob.

(4) If the airplane is equipped with Within the next 10 hours TIS after Follow Liberty Aerospace, Inc.

a reduced sound exhaust system and April 20, 2009 (the effective date Service Document Critical Service

no cracks are found during the of AD 2009-08-05). Bulletin (CSB) CSB-09-001, Revision

initial inspection required in Level B, Revised on March 18, 2009.

paragraph (e)(1) of this AD, install a bypass SCAT tube and a "Do Not Use" placard on or near the heater knob.

(5) If no cracks are found in the (i) For airplanes equipped with a Follow Liberty Aerospace, Inc.

exhaust muffler during the initial standard exhaust system and the Service Document Critical Service

inspection required in paragraph optional bypass SCAT tube has not Bulletin (CSB) CSB-09-001, Revision

(e)(1) of this AD or if the exhaust been installed, repetitively Level B, Revised on March 18, 2009.

muffler was replaced as required in inspect thereafter every 25 hours

muffler was replaced as required in inspect thereafter every 25 hours

paragraph (e)(3) of this AD, TIS or every 12 months, whichever

repetitively inspect thereafter at occurs first.

the intervals specified in (ii) For airplanes equipped with a

paragraphs (e)(5)(i), (e)(5)(ii), standard exhaust system and the

and (e)(5)(iii) of this AD. optional bypass SCAT tube has been

installed, repetitively inspect

thereafter every 50 hours TIS or

every 12 months, whichever occurs

first.

(iii) For airplanes equipped with a

reduced sound exhaust system and

the required bypass SCAT tube has

been installed, repetitively

inspect thereafter every 50 hours

TIS or every 12 months, whichever

occurs first.

(6) Report the results of the Within 10 days after each inspection Use the form (Figure 1 of this AD)

following inspections required in required by this AD. and submit it to FAA, Atlanta

this AD to the FAA. Aircraft Certification Office, 1701

(i) Initial inspection required in Columbia Avenue, College Park,

paragraph (e)(1) of this AD. Georgia 30337; fax: (404) 474-5606;

(ii) Repetitive inspections required e-mail [email protected].

in paragraph (e)(5) of this AD only if cracks are found.

(iii) The Office of Management

and Budget (OMB) approved the

information collection

requirements contained in this

regulation under the provisions

of the Paperwork Reduction Act

of 1980 (44 U.S.C. 3501 et

seq.) and assigned OMB Control

Number 2120-0056.

AD 2009-08-05 R1 Inspection Report

Airplane Serial Number

Airplane Serial Number

Airplane Tach Hours at time of inspection

Propeller type (circle one) MT Sensenich

Propeller Tach Hours at time of inspection

Exhaust Type (circle one) Standard Reduced Sound

Is Exhaust Cracked? (circle one) YES NO

Did lower cowl require trimming at YES NO

the tail pipe opening? (circle one) Not applicable after initial inspection

the tail pipe opening? (circle one) Not applicable after initial inspection

Did the propeller clocking YES NO

position need to be corrected? (circle one) Not applicable after initial inspection.

Were any other discrepancies noticed during the inspection?

Name:

Telephone and/or e-mail address:

Were any other discrepancies noticed during the inspection?

Date:

Send report to: Corey Spiegel, Aerospace Engineer, Atlanta ACO,

1701 Columbia Avenue, College Park, Georgia 30337;

facsimile: (404) 474-5606; e-mail: [email protected].

Figure 1

Special Flight Permit

(f) Under 14 CFR part 39.23, we are limiting the special flight permits for this AD by the following conditions:

Special Flight Permit

(1) The cabin heat turned off; and

(2) The fresh air vents are open.

Alternative Methods of Compliance (AMOCs)

(g) The Manager, Atlanta Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to Attn: Corey Spiegel, Aerospace Engineer, Atlanta ACO, 1701 Columbia Avenue, College Park, Georgia 30337. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

Material Incorporated by Reference

Material Incorporated by Reference

(h) You must use Liberty Aerospace, Inc. Service Document Critical Service Bulletin (CSB) CSB-09-001, Revision Level B, Revised on March 18, 2009, to do the actions required by this AD, unless the AD specifies otherwise.

(1) On April 20, 2009 (74 FR 16117, April 9, 2009), the Director of the Federal Register previously approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact Liberty Aerospace, 100 Aerospace Drive, Melbourne, Florida 32901; telephone: (321) 752-0332 or (800) 759-5953; fax: (321) 752-0377; Internet: http://www.libertyaircraft.com.

(3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329-3768.

(4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Issued in Kansas City, Missouri, on April 7, 2010. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.