Radar Vectors
Airworthiness Directive Current Issued Dec 24, 2008 6 pages Copy saved Nov 17, 2026

AD 2008-26-10 Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2008-1328; Directorate Identifier 2008-CE-066-AD; Amendment 39-15776; AD 2008-26-10] RIN 2120-AA64

Airworthiness Directives; Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

Action

ACTION: Final rule; request for comments.

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Dates

DATES: This AD becomes effective on January 5, 2009.

On January 5, 2009, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD.

We must receive any comments on this AD by February 23, 2009.

ADDRESSES: Use one of the following addresses to comment on this AD.

Addresses

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

• Fax: (202) 493-2251.

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.

• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

To get the service information identified in this AD, contact Cessna Aircraft Company, P.O. Box 7704, Wichita, Kansas 67277; telephone: (800) 423-7762 or (316) 517-6056; Internet: http://www.cessna.com.

To view the comments to this AD, go to http://www.regulations.gov. The docket number is FAA-2008-1328; Directorate Identifier 2008-CE-066-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Ann Johnson, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4105; fax: 316-946-4107; e-mail address: [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

Discussion

Reports of improper installation of the part number (P/N) identification placard on P/N 2013142-18 alternate static air source selector valves prompted us to issue AD 98-01-01, Amendment 39-10286 (63 FR 3455, January 23, 1998), which applies to certain Cessna Aircraft Company (Cessna) Models 172R and 182S airplanes, and AD 2008-10-02, Amendment 39-155508 (73 FR 24168, May 2, 2008), which applies to certain Cessna 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes.

These ADs require inspecting the alternate static air source selector valve to determine if the P/N identification placard obstructs the alternate static air source selector valve port and removing the placard if obstruction is found. These ADs also require reporting to the FAA if obstruction is found.

These assemblies are required for flight into instrument flight rules (IFR) conditions as defined in § 91.411 of the Federal Aviation Regulations (14 CFR 91.411). Use of these assemblies is optional in visual flight rules (VFR) conditions.

After issuing AD 98-01-01 and AD 2008-10-02, we received reports of 15 airplanes not previously affected by either AD with a P/N 2013142-18 installed and the alternate static air source selector valve port was found obstructed by the P/N identification placard.

We have been informed that all P/N 2013142-18 alternate static air source selector valves shipped from Cessna Parts Distribution between January 1, 1993, and March 31, 2008, may have port obstruction caused by the P/N identification placard.

This condition, if not corrected, could result in the altimeter, airspeed, and vertical speed indicators displaying erroneous indications. This could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Relevant Service Information

Relevant Service Information

We reviewed Cessna Single Engine Service Bulletin, SB08-34-02, Revision 1, and Cessna Caravan Service Bulletin CAB08-4, Revision 1, both dated October 6, 2008; Cessna Single Engine Service Bulletin SEB08-5 and Cessna Multi-engine Service Bulletin MEB08-6, both dated October 13, 2008.

The service information describes procedures for inspecting the alternate static air source selector valve to assure that the P/N identification placard does not obstruct the alternate static air source selector valve port.

FAA's Determination and Requirements of This AD

FAA's Determination and Requirements of This AD

We are issuing this AD because we evaluated all the information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This AD requires inspecting the alternate static air source selector valve to assure that the P/N identification placard does not obstruct the alternate static air source selector valve port. If the P/N identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found.

FAA's Determination of the Effective Date

FAA's Determination of the Effective Date

Since an unsafe condition exists that requires the immediate adoption of this AD, we determined that notice and opportunity for public comment before issuing this AD are impracticable, and that good cause exists for making this amendment effective in fewer than 30 days.

Comments Invited

Comments Invited

This AD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and an opportunity for public comment. We invite you to send any written relevant data, views, or arguments regarding this AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number "FAA-2008-1328; Directorate Identifier 2008-CE-066-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the AD. We will consider all comments received by the closing date and may amend the AD in light of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this AD.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a "significant regulatory action" under Executive Order 12866;

(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket that contains the AD, the regulatory evaluation, any comments received, and other information on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5527) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by adding a new AD to read as follows:

2008-26-10 Cessna Aircraft Company: Amendment 39-15776; Docket No. FAA-2008-1328; Directorate Identifier 2008-CE-066-AD.

Effective Date

Effective Date

(a) This AD becomes effective on January 5, 2009.

Affected ADs

(b) This AD relates to AD 98-01-01, Amendment 39-10287 and AD 2008-10-02, Amendment 39-15508. These ADs can be found on the Internet at the following Web site: http://rgl.faa.gov/.

Applicability

(c) This AD applies to all serial numbers (S/Ns) of the airplanes listed in Table 1 of this AD, certificated in any category, that:

Applicability

(1) Were initially delivered from the manufacturer between January 1, 1993, and March 31, 2008, unless the modification/rework required in AD 2008-10-02 has been done and you remain in compliance with that AD; or

(2) Have a part number (P/N) 2013142-18 installed as a replacement part anytime after January 1, 1993, unless the modification/rework required in AD 2008-10-02 has been done and you remain in compliance with that AD.

Note 1: The affected part was shipped from Cessna Parts Distribution (CPD) between January 1, 1993, and March 31, 2008.

Note 2: P/N 2013142-18 replaced P/Ns 2013142-9, -13, and -17.

Table 1--Applicable Airplane Models

Models

172 F172K 177

172A F172L 177A

172B F172M 177B

172C F172N 177RG

172D F172P F177RG

172E FR172E 180

172F (USAF T-41A) FR172F 180A

172G FR172G 180B

172H (USAF T-41A) FR172H 180C

172I FR172J 180D

172K FR172K 180E

172L P172D 180F

172M R172E (USAF T-41B), (USAF T-41C and 180G

D)

172N R172F (USAF T-41) 180H

172P R172G (USAF T-41C or D) 180J

172Q R172H (USAF T-41D) 180K

172R R172J 182

172S R172K 182A

F172D 172RG 182B

F172E 175 182C

F172F 175A 182D

F172G 175B 182E

F172H 175C 182F

182G A185F U206D

182H 206 U206E

182J 206H U206F

182K P206 U206G

182L P206A 207

182M P206B 207A

182N P206C T207

182P P206D T207A

182Q P206E 208

182R T206H 208B

182S TP206A 210

182T TP206B 210A

F182P TP206C 210B

F182Q TP206D 210C

FR182 TP206E 210D

R182 TU206A 210E

T182 TU206B 210F

T182T TU206C 210G

TR182 TU206D 210H

185 TU206E 210J

185A TU206F 210K

185B TU206G 210L

185C U206 210M

185D U206A 210N

185E U206B 210R

A185E U206C 210-5 (205)

210-5A (205A) FT337F

T210F M337B (USAF 02A)

T210G T337B

T210H T337C

T210J T337D

T210K T337E

T210L T337F

T210M T337H

T210N T337H-SP

T210R T303 336 337 337A (USAF 02B) 337B 337C 337D 337E 337F 337G 337H F337E F337F F337G F337H FT337E

T210R T303 336 337 337A (USAF 02B) 337B 337C 337D 337E 337F 337G 337H F337E F337F F337G F337H FT337E

Unsafe Condition

(e) This AD is the result of reports of improper installation of the part number identification placard on the alternate static air source selector valve. We are issuing this AD to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done. A person authorized to perform maintenance as specified in 14 CFR section 43.3 of the Federal Aviation Administration Regulations (14 CFR 43.3) is required to do all the actions required in this AD.

Actions Compliance Procedures

(1) For all affected Within the next 100 Following the

airplanes that are not hours time-in- procedures in

equipped for flight under service (TIS) after Cessna Single

instrument flight rules January 5, 2009 Engine Service

(IFR): Inspect the (the effective date Bulletin SB08-34-

alternate static air source of this AD) or 02, Revision 1,

selector valve to assure within the next 4 dated October 6,

that the part number months after 2008; Cessna

identification placard is January 5, 2009 Caravan Service

not obstructing the port. (the effective date Bulletin CAB08-4,

of this AD), Revision 1, dated

whichever occurs October 6, 2008;

first. Cessna Single

Engine Service

Bulletin SEB08-5,

dated October 13,

2008; or Cessna

Multi-engine

Service Bulletin

MEB08-6, dated

October 13, 2008,

as applicable.

(2) For all affected (A) Inspect within Following the

airplanes that are equipped the next 10 days procedures in

for flight under instrument after January 5, Cessna Single

flight rules (IFR): 2009 (the effective Engine Service

date of this AD); Bulletin SB08-34-

or 02, Revision 1,

(B) Install placards dated October 6,

before further 2008; Cessna

flight after Caravan Service

January 5, 2009 Bulletin CAB08-4,

(the effective date Revision 1, dated

of this AD). October 6, 2008;

Cessna Single

Engine Service

Bulletin SEB08-5,

dated October 13,

2008; or Cessna

Multi-engine

Service Bulletin

MEB08-6, dated

October 13, 2008,

as applicable.

(i) Inspect the

alternate static air

source selector valve

to assure that the part

number identification

placard is not

obstructing the port;

or

(ii) Fabricate a placard

that incorporates the

following words (using

at least \1/8\-inch

letters) and install

this placard on the

instrument panel within

the pilot's clear view:

"IFR OPERATION IS

PROHIBITED" and "USE

OF THE ALTERNATE STATIC

AIR SOURCE IS

PROHIBITED."

(3) For all affected Within the next 100 Following the

airplanes that are equipped hours TIS after procedures in

for flight under instrument January 5, 2009 Cessna Single

flight rules (IFR): If (the effective date Engine Service

placards were installed in of this AD) or Bulletin SB08-34-

accordance with paragraph within the next 4 02, Revision 1,

(e)(2)(ii) of this AD, months after dated October 6,

inspect the alternate January 5, 2009 2008; Cessna

static air source selector (the effective date Caravan Service

valve to assure that the of this AD), Bulletin CAB08-4,

part number identification whichever occurs Revision 1, dated

placard is not obstructing first. After doing October 6, 2008;

the port. the inspection, Cessna Single

remove the placards Engine Service

installed in Bulletin SEB08-5,

accordance with dated October 13,

paragraph 2008; or Cessna

(e)(2)(ii) of this Multi-engine

AD before further Service Bulletin

flight. MEB08-6, dated

October 13, 2008,

as applicable.

(4) For all affected Before further Following the

airplanes: If the alternate flight after the procedures in

static air source selector inspection required Cessna Single

valve port is found in paragraphs Engine Service

obstructed by the part (e)(1), (e)(2)(i), Bulletin SB08-34-

number identification and (e)(3) of this 02, Revision 1,

placard during the AD. dated October 6,

inspection required in 2008; Cessna

paragraphs (e)(1), Caravan Service

(e)(2)(i), and (e)(3) of Bulletin CAB08-04,

this AD, remove the placard Revision 1, dated

from the valve body, October 6, 2008;

discard the placard, and Cessna Single

assure that the port is Engine Service

open and unobstructed. Bulletin SEB08-5,

dated October 13,

2008; or Cessna

Multi-engine

Service Bulletin

MEB08-6, dated

October 13, 2008,

as applicable.

(5) For all affected As of 10 days after A person authorized

airplanes: When a January 5, 2009 to perform

replacement valve is (the effective date maintenance as

needed, only install a P/N of this AD). specified in 14 CFR

2013142-18 alternate static section 43.3 of the

air source selector valve Federal Aviation

that has been inspected and Administration

the port is found free from Regulations (14 CFR

obstruction. 43.3) is required

to do the

inspection.

(f) Report to the FAA the results of the inspection required by this AD where an obstruction was found.

(1) Submit this report within 10 days after the inspection or 10 days after the effective date of this AD, whichever occurs later.

(2) Use the form in Figure 1 of this AD and submit it to FAA, Manufacturing Inspection District Office, Mid-Continent Airport, 1804 Airport Road, Room 101, Wichita, Kansas 67209; or fax to (316) 946-4189.

(3) The Office of Management and Budget (OMB) approved the information collection requirements contained in this regulation under the provisions of the Paperwork Reduction Act of 1980 (44 U.S.C. 3501 et seq.) and assigned OMB Control Number 2120-0056.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(g) The Manager, Wichita Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Ann Johnson, Aerospace Engineer, FAA, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4105; fax: 316-946-4107; e-mail address: [email protected]. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

(h) AMOCs approved for AD 2008-10-02 are approved for this AD.

Material Incorporated by Reference

Material Incorporated by Reference

(i) You must use Cessna Single Engine Service Bulletin, SB08-34-02, Revision 1, dated October 6, 2008; Cessna Caravan Service Bulletin CAB08-4, Revision 1, dated October 6, 2008; Cessna Single Engine Service Bulletin SEB08-5, dated October 13, 2008; and Cessna Multi-engine Service Bulletin MEB08-6, dated October 13, 2008, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact Cessna Aircraft Company, P.O. Box 7704, Wichita, Kansas 67277; telephone: (800) 423-7762 or (316) 517-6056; Internet: http://www.cessna.com.

(3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Issued in Kansas City, Missouri, on December 15, 2008. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.