Radar Vectors
Airworthiness Directive Current Issued Oct 16, 2008 4 pages Copy saved Nov 17, 2026

AD 2008-21-08 Air Tractor, Inc. Models AT-402, AT-402A, and AT-402B Airplanes

We are adopting a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-402, AT-402A, and AT-402B airplanes. This AD requires you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners and inspect the rudder or vertical fin skins, spars, hinges, or brackets for cracks and/or corrosion. This AD also requires you to replace any damaged parts found as a result of the inspections and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements. This AD results from a report of a Model AT-402 airplane with a loose upper rudder hinge caused by fatigue. We are issuing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges, or brackets; or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2008-0749; Directorate Identifier 2008-CE-044-AD; Amendment 39-15692; AD 2008-21-08] RIN 2120-AA64

Airworthiness Directives; Air Tractor, Inc. Models AT-402, AT-402A, and AT-402B Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

Action

ACTION: Final rule.

SUMMARY: We are adopting a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-402, AT-402A, and AT-402B airplanes. This AD requires you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners and inspect the rudder or vertical fin skins, spars, hinges, or brackets for cracks and/or corrosion. This AD also requires you to replace any damaged parts found as a result of the inspections and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements. This AD results from a report of a Model AT-402 airplane with a loose upper rudder hinge caused by fatigue. We are issuing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges, or brackets; or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control.

Dates

DATES: This AD becomes effective on November 20, 2008.

On November 20, 2008, the Director of the Federal Register approved the incorporation by reference of Snow Engineering Co. Service Letter 247, revised June 2, 2008, listed in this AD.

As of December 21, 2006 (71 FR 66661, November 16, 2006), the Director of the Federal Register approved the incorporation by reference of Snow Engineering Co. Process Specification Number 145, dated December 6, 1991, listed in this AD.

Addresses

ADDRESSES: For service information identified in this AD, contact Air Tractor, Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564-5616; facsimile: (940) 564-5612; E-mail: [email protected]; Web site: http://www.airtractor.com.

To view the AD docket, go to U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, or on the Internet at http://www.regulations.gov. The docket number is FAA-2008-0749; Directorate Identifier 2008-CE-044-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Andy McAnaul, Aerospace Engineer, 10100 Reunion Pl, San Antonio, Texas 78216; telephone: (210) 308-3365; fax: (210) 308-3370.

SUPPLEMENTARY INFORMATION:

Discussion

On July 1, 2008, we issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain Air Tractor Models AT-402, AT-402A, and AT-402B airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on July 8, 2008 (73 FR 38933). The NPRM proposed to require you to repetitively visually inspect the rudder and vertical fin hinge attaching structure for loose fasteners and inspect the rudder or vertical fin skins, spars, hinges, or brackets for cracks and/or corrosion. This AD would also require you to replace any damaged parts found as a result of the inspections and install an external doubler at the upper rudder hinge. Installation of the external doubler at the upper rudder hinge is terminating action for the repetitive inspection requirements.

Comments

Comments

We provided the public the opportunity to participate in developing this AD. We received no comments on the proposal or on the determination of the cost to the public.

Conclusion

We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial corrections. We have determined that these minor corrections:

Conclusion

• Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and

• Do not add any additional burden upon the public than was already proposed in the NPRM.

Costs of Compliance

We estimate that this AD affects 220 airplanes in the U.S. registry.

Costs of Compliance

We estimate the following costs to do the inspection:

Total cost

Labor cost Parts cost Total cost on U.S.

per airplane operators

1 work-hour x $80 per hour = $80 … Not applicable … $80 $17,600

Any required replacements will vary depending upon the damage found, and any replacements required will vary based on the results of the inspection. Based on this, we have no way of determining the potential replacement costs for each airplane or the number of airplanes that will need the replacements based on the result of the inspections.

We estimate the following costs to do installation of the external doubler at the upper rudder hinge:

Total cost

Labor cost Parts cost Total cost on U.S.

per airplane operators

5 work-hours x $80 per hour = $217 $617 $135,740

$400 …

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this AD.

Regulatory Findings

Regulatory Findings

We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this AD (and other information as included in the Regulatory Evaluation) and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "Docket No. FAA-2008-0749; Directorate Identifier 2008 CE-044-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding the following new AD:

2008-21-08 Air Tractor, Inc.: Amendment 39-15692; Docket No. FAA-2008-0749; Directorate Identifier 2008-CE-044-AD.

Effective Date

Effective Date

(a) This AD becomes effective on November 20, 2008.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Models AT-402, AT-402A, and AT-402B airplanes, serial numbers 0694 through 1176, that are certificated in any category.

Unsafe Condition

(d) This AD results from a report of a Model AT-402 airplane with a loose upper rudder hinge caused by fatigue. We are issuing this AD to detect and correct loose fasteners; any cracks in the rudder or vertical fin skins, spars, hinges, or brackets; or corrosion of the rudder and vertical fin hinge attaching structure. Hinge failure adversely affects ability to control yaw and has led to the rudder folding over in flight. This condition could allow the rudder to contact the elevator and affect ability to control pitch with consequent loss of control.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Actions Compliance Procedures

(1) Inspect visually the rudder Initially inspect Follow Snow

and vertical fin hinge when the airplane Engineering Co.

attachment for loose fasteners; reaches a total Service Letter

and inspect the rudder or of 3,500 hours 247,

vertical fin skins, spars, time-in-service revised June 2,

hinges, and brackets for cracks (TIS) or within 2008.

and/or corrosion. the next 100

(1) Inspect visually the rudder Initially inspect Follow Snow

hours TIS after

November 20, 2008

(the effective

date of this AD),

whichever occurs

later.

Thereafter,

repetitively

inspect at

intervals not to

exceed every 100

hours TIS.

Installation of

the external

doubler at the

upper rudder

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

is terminating

action for the

repetitive

inspections

required by this

AD. (2) If you find any damage as a result of any inspection required by paragraph (e)(1) of this AD, you must:

(i) Replace any damaged

parts with new parts; and

(ii) Do the installation of Before further Follow Snow

the external doubler at the flight after any Engineering Co.

upper rudder hinge. inspection Service Letter

required by 247,

paragraph (e)(1) revised June 2,

of this AD where 2008; and Snow

you find any Engineering Co.

damaged parts. Process

The installation Specification

of the external Number 145, dated

doubler at the December 6, 1991.

upper rudder

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

terminates the

repetitive

inspections

required by this

AD.

(3) Do the installation of the When the airplane Follow Snow

external doubler at the upper reaches a total Engineering Co.

rudder hinge. of 5,000 hours Service Letter

TIS after 247,

November 20, 2008 revised June 2,

(the effective 2008; and Snow

date of this AD) Engineering Co.

or within the Process

next 100 hours Specification

TIS after Number 145, dated

November 20, 2008 December 6, 1991.

(the effective

date of this AD),

whichever occurs

later. The

installation of

the external

doubler at the

upper rudder

hinge required by

paragraph

(e)(2)(ii) or

(e)(3) of this AD

terminates the

repetitive

inspections

required by this

AD.

(4) Do not install any rudder As of November 20, Not Applicable.

without the external doubler at 2008 (the the upper rudder hinge required effective date of by paragraph (e)(3) of this AD. this AD).

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Fort Worth Airplane Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

Material Incorporated by Reference

Material Incorporated by Reference

(g) You must use Snow Engineering Co. Service Letter 247, revised June 2, 2008; and Snow Engineering Co. Process Specification Number 145, dated December 6, 1991, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of Snow Engineering Co. Service Letter 247, revised June 2, 2008, under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) On December 21, 2006 (71 FR 66661, November 16, 2006), the Director of the Federal Register approved the incorporation by reference of Snow Engineering Co. Process Specification Number 145, dated December 6, 1991.

(3) For service information identified in this AD, contact Air Tractor, Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564-5616; facsimile: (940) 564-5612; E-mail: [email protected]; Web site: http://www.airtractor.com.

(4) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Issued in Kansas City, Missouri. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.