AD 2006-21-03 Cirrus Design Corporation Models SR20 and SR22 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This AD requires you to check the maintenance records to determine whether the brake caliper piston O-ring seals were replaced at the last annual or 100-hour inspection. If the O-rings were not replaced, this AD requires you to replace the O-ring seals with new seals or replace brake calipers. This AD also requires you to modify the main landing gear wheel fairings to add temperature indicator sticker inspection holes, trim the wheel fairings to prevent them from holding fluids, install temperature indicator stickers on the brake calipers, and insert Revision A6 (with revised preflight walk-around, a limitation on the engine speed used to taxi, and brake inspection/servicing intervals) into the Pilot's Operating Handbook (POH). This AD results from several reports of airplanes experiencing brake fires and two airplanes losing directional control. We are issuing this AD to detect, correct, and prevent overheating damage to the brake caliper piston O-ring seals, which could result in leakage of brake hydraulic fluid. Consequently, this could lead to the loss of braking with loss of airplane directional control or brake fire.
[Docket No. FAA-2006-24010; Directorate Identifier 2006-CE-14-AD; Amendment 39-14787; AD 2006-21-03] RIN 2120-AA64
Airworthiness Directives; Cirrus Design Corporation Models SR20 and SR22 Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
Summary
SUMMARY: The FAA adopts a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This AD requires you to check the maintenance records to determine whether the brake caliper piston O-ring seals were replaced at the last annual or 100-hour inspection. If the O-rings were not replaced, this AD requires you to replace the O-ring seals with new seals or replace brake calipers. This AD also requires you to modify the main landing gear wheel fairings to add temperature indicator sticker inspection holes, trim the wheel fairings to prevent them from holding fluids, install temperature indicator stickers on the brake calipers, and insert Revision A6 (with revised preflight walk-around, a limitation on the engine speed used to taxi, and brake inspection/servicing intervals) into the Pilot's Operating Handbook (POH). This AD results from several reports of airplanes experiencing brake fires and two airplanes losing directional control. We are issuing this AD to detect, correct, and prevent overheating damage to the brake caliper piston O-ring seals, which could result in leakage of brake hydraulic fluid. Consequently, this could lead to the loss of braking with loss of airplane directional control or brake fire.
Dates
DATES: This AD becomes effective on November 17, 2006.
As of November 17, 2006, the Director of the Federal Register approved the incorporation by reference of certain publications listed in the regulation.
ADDRESSES: To get the service information identified in this AD, contact Cirrus Design Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811; telephone: (218) 727-2737 or on the Internet at http://www.cirrusdesign.com.
Addresses
To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-001 or on the Internet at http://dms.dot.gov. The docket number is Docket No. FAA-2006-24010; Directorate Identifier 2006-CE-14-AD.
For Further Information Contact
FOR FURTHER INFORMATION CONTACT: Wess Rouse, Aerospace Engineer, ACE-117C, Chicago Aircraft Certification Office, 2300 East Devon Avenue, Room 107, Des Plaines, Illinois 60018; telephone: (847) 294-8113; facsimile: (847) 294-7834.
SUPPLEMENTARY INFORMATION:
Discussion
On May 1, 2006, we issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain CDC Models SR20 and SR22 airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on May 8, 2006 (71 FR 26707). The NPRM proposed to require you to check the maintenance records to determine whether the brake caliper piston O-ring seals were replaced at the last annual or 100-hour inspection. If the O-rings were not replaced, this proposed AD would require you to replace the O-ring seals with new seals or replace brake calipers. This proposed AD would also require you to modify the main landing gear wheel fairings to add temperature indicator sticker inspection holes, trim the wheel fairings to prevent them from holding fluids, install temperature indicator stickers on the brake calipers, and insert Revision A6 (with revised preflight walk-around and taxi procedures) into the Pilot's Operating Handbook (POH).
Comments
Comments
We provided the public the opportunity to participate in developing this AD. The following presents the comment received on the proposal and FAA's response to the comment:
Comment Issue: Increase Emphasis on the Operational Aspects of Overheating of the Brakes
CDC points out that the brakes, as delivered, meet certification requirements, and when properly used, will provide the expected performance and service. We conclude that CDC believes that the AD overemphasizes the required maintenance actions and hardware upgrades, without explaining the operational details that will prevent brake caliper O-ring damage.
Comment Issue: Increase Emphasis on the Operational Aspects of Overheating of the Brakes
Our intent is that the AD stress continued operational safety by removing and replacing potentially damaged O-rings or replacement of existing brake calipers with new heavier duty calipers (with new O-rings installed), adding brake caliper temperature stickers with a new inspection hole in the wheel fairings (to detect potential O-ring damage before brake fluid leaks develop), and adding a revision to the Pilot's Operating Handbook (to emphasize brake preflight inspections, checking the color of the brake caliper temperature sticker for evidence of brake caliper overheating, and limiting the engine RPM during taxi to 1000 RPM).
We agree that the operational change to limit engine RPM during taxi (found in Revision A6 to the POH) is the most important consideration toward preventing brake caliper O-ring seal damage. This AD is requiring this action so we are not changing the AD as a result of this comment.
Conclusion
Conclusion
We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial corrections. We have determined that these minor corrections:
• Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and
• Do not add any additional burden upon the public than was already proposed in the NPRM.
Costs of Compliance
Costs of Compliance
We estimate that this AD affects 2,135 airplanes in the U.S. registry.
We estimate the following costs to do the check of maintenance records to determine whether the brake caliper piston O-ring seals were replaced at the last annual or 100-hour inspection:
Total cost per Total cost on
Labor cost Parts cost airplane U.S. operators
1 work-hour x $80 = $80 … Not Applicable … $80 $170,800
We estimate the following costs to install any necessary O-ring seals that would be required based on the results of this check of maintenance records. We have no way of determining the number of airplanes that may need this seal installation:
Total cost per
Labor cost Parts cost airplane
4 work-hours x $80 = $320 … $8 $328
We estimate the following costs to replace any brake calipers on Model SR20 airplanes, serial numbers (S/Ns) 1005 through 1194, that would be required based on the results of this check of maintenance records. We have no way of determining the number of these Model SR20 airplanes that may need to replace brake calipers:
Total cost per
Labor cost Parts cost airplane
12 work-hours x $80 = $960 … $1,167 $2,127
We estimate the following costs to replace any brake calipers on Model SR20 airplanes, S/Ns 1195 through 1600, that would be required based on the results of this check of maintenance records. We have no way of determining the number of these Model SR20 airplanes that may need to replace brake calipers:
Total cost per
Labor cost Parts cost airplane
8 work-hours x $80 = $640 … $1,167 $1,807
We estimate the following costs to replace any brake calipers on Model SR22 airplanes that would be required based on the results of this check of maintenance records. We have no way of determining the number of Model SR22 airplanes that may need to replace brake calipers:
Total cost per
Labor cost Parts cost airplane
5 work-hours x $80 = $400 … $845 $1,245
We estimate the following costs to do the modification of the MLG wheel fairings to add the temperature indicator sticker inspection holes, trim the wheel fairings to prevent them from holding fluids, and install the temperature indicator sticker on the brake calipers:
Total cost per Total cost on
Labor cost Parts cost airplane U.S. operators
2 work-hours x $80 = $160 … $2 $162 $345,870
The CDC has indicated that CDC will provide warranty credit as stated in the service information for modifying the MLG wheel fairings by adding the temperature indicator sticker inspection holes, trimming the wheel fairings to prevent them from holding fluids, and installing the temperature indicator sticker on the brake calipers.
We estimate the following costs to do the insertion of Revision A6 into the POH:
Total cost per Total cost on
Labor cost Parts cost airplane U.S. operators
1 work-hour x $80 … Not Applicable … $80 $170,800
Authority for This Rulemaking
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the agency's authority.
We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this AD.
Regulatory Findings
Regulatory Findings
We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
1. Is not a "significant regulatory action" under Executive Order 12866;
2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a summary of the costs to comply with this AD (and other information as included in the Regulatory Evaluation) and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "Docket No. FAA-2006-24010; Directorate Identifier 2006-CE-14-AD" in your request.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. FAA amends § 39.13 by adding a new AD to read as follows:
2006-21-03 Cirrus Design Corporation: Amendment 39-14787; Docket No. Docket No. FAA-2006-24010; Directorate Identifier 2006-CE-14-AD.
Effective Date
Effective Date
(a) This AD becomes effective on November 17, 2006.
Affected ADs
(b) None.
Applicability
(c) This AD applies to the following airplane models and serial numbers (S/N) that are certificated in any category:
(1) Group 1: Model SR20 Airplanes, S/N 1005 through 1600.
(2) Group 2: Model SR22 Airplanes, S/N 0002 through 1739.
Applicability
(3) Group 3: Model SR20 Airplanes, S/N 1005 through 1592.
(4) Group 4: Model SR22 Airplanes, S/N 0002 through 1727.
Unsafe Condition
(d) This AD results from several reports of airplanes that experienced brake fires and two airplanes that lost directional control. The actions specified in this AD are intended to detect, correct, and prevent overheating damage to the brake caliper piston O-ring seals, which could result in leakage of brake hydraulic fluid. Consequently, this could lead to the loss of braking with loss of airplane directional control or brake fire.
Compliance
Compliance
(e) To address this problem, you must do the following:
Table 1.--Actions/Compliance/Procedures
Actions Compliance Procedures
(1) For Group 1 and Group 2 Within 50 hours No special
airplanes: time-in-service procedures
Check the maintenance records (TIS) after necessary to
to determine whether the brake November 17, 2006 check the
caliper piston O-ring seals (the effective maintenance
were replaced at the last date of this AD), records. The
annual or 100-hour inspection. unless already owner/operator
done. holding at least
a private pilot
certificate as
authorized by
section 43.7 of
the Federal
Aviation
Regulations (14
CFR 43.7) may
make this check.
You must make an
entry into the
airplane records
that shows
compliance with
this portion of
the AD in
accordance with
section 43.9 of
the Federal
Aviation
Regulations (14
CFR 43.9).
(2) For Group 1 and Group 2 Before further For the
airplanes: If you find as a flight after the replacement,
result of the check required by check required by follow the brake
result of the check required by check required by follow the brake
paragraph (e)(1) of this AD paragraph (e)(1) maintenance
that there is no record of the of this AD. procedures in
replacement of brake caliper Section 32-42 of
piston O-ring seals at the last the SR20 or SR22
annual or 100-hour inspection, Aircraft
then do the following: Maintenance
(i) Replace the O-ring seals Manual. For the
with new O-ring seals or replacement of
(ii) Replace old brake calipers the new brake
with new brake calipers. calipers, follow
Cirrus Design
Corporation
Service Bulletin
SB 2X-32-13 R1,
Issued: December
15, 2005, Revised
May 16, 2006.
(3) For Group 3 and Group 4 Do the Follow Cirrus
airplanes: modification Design
(i) Modify the main landing within 50 hours Corporation
gear (MLG) wheel fairings to TIS after Service Bulletin
add temperature indicator November 17, 2006 SB 2X-32-14 R1,
sticker inspection holes and (the effective Issued: January
trim the wheel fairings to date of this AD), 18, 2006,
prevent them from holding unless already Revised: February
fluids; and done. Do the 17, 2006.
(ii) Install a temperature temperature
indicator sticker on the brake indicator sticker
calipers. installation
within 50 hours
TIS after
November 17, 2006
(the effective
date of this AD),
unless already
done, and
thereafter before
further flight
anytime you have
the O-ring seals
replaced due to
overheating of
the brake
assembly
(temperature
indicator sticker
turned black).
(4) For all airplanes: Within 50 hours The owner/operator
Insert the appropriate Revision TIS after holding at least
A6 part number (P/N) into the November 17, 2006 a private pilot
Pilot's Operating Handbook (the effective certificate as
(POH), as presented in TABLE date of this AD), authorized by
2.--REVISION A6 TO THE PILOT'S unless already section 43.7 of
OPERATING HANDBOOK, in done. the Federal
paragraph (f) of this AD. Aviation
Regulations (14
CFR 43.7) may
insert the
information into
the POH as
specified in
paragraph (e)(4)
of this AD. Make
an entry into the
airplane
maintenance
records showing
compliance with
this portion of
the AD in
accordance with
section 43.9 of
the Federal
Aviation
Regulations (14
CFR 43.9).
(5) For Group 3 and Group 4 As of November 17, Follow Cirrus
airplanes: 2006 (the Design
(i) Do not install any MLG effective date of Corporation
fairings without also doing the this AD). Service Bulletin
modifications required by SB 2X-32-14 R1,
paragraph (e)(3)(i) of this AD; Issued: January
and 18, 2006,
(ii) Do not replace any brake Revised: February
calipers without also 17, 2006.
installing the temperature indicator sticker required by paragraph (e)(3)(ii) of this AD.
(f) The following table specifies the POH Revision A6 part number as required in paragraph (e)(4) of this AD:
Table 2.--Revision A6 to the Pilot's Operating Handbook
Model SR20 or
Affected airplanes SR22 airplane Date FAA-approved
POH P/N
(1) Model SR20, S/N 1148 11934-002 January 18, 2006.
through 1267.
(2) Model SR20, S/N 1005 11934-002 January 18, 2006.
through 1147 that have the 3,000-pound gross weight modification following Cirrus Design Corporation Service Bulletin SB 20-01-00, Issued: February 25, 2003.
(3) SR20, S/N 1268 through 11934-003 January 18, 2006.
1739.
(4) SR22, S/N 002 through 13772-001 January 18, 2006.
1739.
Alternative Methods of Compliance (AMOCs)
(g) The Manager, Chicago Aircraft Certification Office (ACO), ATTN: Wess Rouse, Aerospace Engineer, FAA, ACE-117C, Chicago ACO, 2300 East Devon Avenue, Room 107, Des Plaines, Illinois 60018; telephone: (847) 294-8113; facsimile: (847) 294-7834, has the authority to approve alternative methods of compliance for this AD, if requested using the procedures found in 14 CFR 39.19.
Material Incorporated by Reference
Material Incorporated by Reference
(h) You must do the actions required by this AD following the instructions in Cirrus Design Corporation Service Bulletin SB 2X-32-13 R1, Issued: December 15, 2005, Revised May 16, 2006; and Cirrus Design Corporation Service Bulletin SB 2X-32-14 R1, Issued: January 18, 2006, Revised: February 17, 2006. The Director of the Federal Register approved the incorporation by reference of this service bulletin in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. To get a copy of this service information, contact Cirrus Design Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811; telephone: (218) 727-2737 or on the Internet at www.cirrusdesign.com. To review copies of this service information, go to the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html or call (202) 741-6030. To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-001 or on the Internet at http://dms.dot.gov. The docket number is Docket No. FAA-2006-24010; Directorate Identifier 2006-CE-14-AD.
Issued in Kansas City, Missouri, on October 3, 2006. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.