Radar Vectors
Airworthiness Directive Current Issued Jun 29, 2006 3 pages Copy saved Nov 17, 2026

AD 2006-13-15 Mitsubishi Heavy Industries MU-2B Series Airplanes

We are adopting a new airworthiness directive (AD) for all Mitsubishi Heavy Industries MU-2B series airplanes. This AD requires you to do the following: Remove and visually inspect the wing attach barrel nuts, bolts, and retainers for cracks, corrosion, and fractures; replace any cracked, corroded, or fractured parts; inspect reusable wing attach barrel nuts and bolts for deformation and irregularities in the threads; check the minimum breakaway torque of reused wing attach barrel nuts; replace any deformed or irregular parts; and install new or reusable parts and torque to the correct value. This AD results from a recent safety evaluation that used a data-driven approach to evaluate the design, operation, and maintenance of the MU-2B series airplanes in order to determine their safety and define what steps, if any, are necessary for their safe operation. Part of that evaluation was the identification of unsafe conditions that exist or could develop on the affected type design airplanes. We are issuing this AD to detect and correct cracks, corrosion, fractures, and incorrect torque values in the wing attach barrel nuts, which could result in failure of the wing barrel nuts and/or associated wing attachment hardware. This failure could lead to in-flight separation of the outer wing from the center wing section and result in loss of controlled flight.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2006-23578; Directorate Identifier 2006-CE-01-AD; Amendment 39-14668; AD 2006-13-15] RIN 2120-AA64

Airworthiness Directives; Mitsubishi Heavy Industries MU-2B Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

Action

ACTION: Final rule.

SUMMARY: We are adopting a new airworthiness directive (AD) for all Mitsubishi Heavy Industries MU-2B series airplanes. This AD requires you to do the following: Remove and visually inspect the wing attach barrel nuts, bolts, and retainers for cracks, corrosion, and fractures; replace any cracked, corroded, or fractured parts; inspect reusable wing attach barrel nuts and bolts for deformation and irregularities in the threads; check the minimum breakaway torque of reused wing attach barrel nuts; replace any deformed or irregular parts; and install new or reusable parts and torque to the correct value. This AD results from a recent safety evaluation that used a data-driven approach to evaluate the design, operation, and maintenance of the MU-2B series airplanes in order to determine their safety and define what steps, if any, are necessary for their safe operation. Part of that evaluation was the identification of unsafe conditions that exist or could develop on the affected type design airplanes. We are issuing this AD to detect and correct cracks, corrosion, fractures, and incorrect torque values in the wing attach barrel nuts, which could result in failure of the wing barrel nuts and/or associated wing attachment hardware. This failure could lead to in-flight separation of the outer wing from the center wing section and result in loss of controlled flight.

Dates

DATES: This AD becomes effective on August 11, 2006.

As of August 11, 2006, the Director of the Federal Register approved the incorporation by reference of certain publications listed in the regulation.

ADDRESSES: For service information identified in this AD, contact Mitsubishi Heavy Industries America, Inc., 4951 Airport Parkway, Suite 800, Addison, Texas 95001; telephone: (972) 934-5480; fax: (972) 934-5488, or Turbine Aircraft Services, Inc., 4550 Jimmy Doolittle Drive, Addison, Texas 75001; telephone: (972) 248-3108; facsimile: (972) 248-3321.

Addresses

To view the AD docket, go to the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-0001, or on the Internet at http://dms.dot.gov. The docket number is FAA-2006-23578; Directorate Identifier 2006-CE-01-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370.

SUPPLEMENTARY INFORMATION:

Discussion

On April 18, 2006, we issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to all Mitsubishi Heavy Industries MU-2B series airplanes. This proposal was published in the Federal Register as a supplemental notice of proposed rulemaking (NPRM) on April 24, 2006 (71 FR 20915). We issued the supplemental NPRM to incorporate revised manufacturer service information that adds airplanes to the applicability, revises the serial numbers of the affected airplanes, and updates the manufacturer's contact information. The supplemental NPRM proposed to require you to do the following:

Discussion

• Remove and visually inspect the wing attach barrel nuts, bolts, and retainers for cracks, corrosion, and fractures;

• Replace any cracked, corroded, or fractured wing attach barrel nuts, bolts, and retainers with new parts;

• Inspect reusable wing attach barrel nuts and bolts for deformation and irregularities in the threads;

• Check the minimum breakaway torque of reused wing attach barrel nuts;

• Replace any deformed or irregular wing attach barrel nuts or bolts with new parts; and

• Install new or reusable parts and torque to the correct value.

Comments

Comments

We provided the public the opportunity to participate in developing this AD. We received no comments on the proposal or on the determination of the cost to the public.

Conclusion

We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial corrections. We have determined that these minor corrections:

Conclusion

• are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and

• do not add any additional burden upon the public than was already proposed in the NPRM.

Costs of Compliance

We estimate that this AD affects 399 airplanes in the U.S. registry.

Costs of Compliance

We estimate the following costs to do the inspection:

Total cost for

Labor cost Parts cost each airplane Total cost on U.S. operators

12 work-hours x $80 an hour = Not applicable … $960 $960 x 399 = $383,040

$960.

We estimate the following costs to do any necessary replacements that will be required based on the results of the inspection. We have no way of determining the number of airplanes that may need this replacement:

Total cost for

each airplane to

Labor cost Parts cost replace all 8 wing

attach barrel nuts

No additional labor cost. Any $60 for each barrel $480

necessary replacements will nut. There are 8

be done at the time of barrel nuts on each

inspection. airplane. Possible

total cost of: $60 x

8 = $480.

The FAA is committed to updating the aviation community of expected costs associated with the MU-2B series airplane safety evaluation conducted in 2005. As a result of that commitment, the accumulating expected costs of all ADs related to the MU-2B series airplane safety evaluation may be found in the Final Report section at the following Web site: http://www.faa.gov/aircraft/air_cert/design_approvals/small_airplanes/cos/mu2_foia_reading_library/.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this AD.

Regulatory Findings

Regulatory Findings

We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this AD (and other information as included in the Regulatory Evaluation) and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "Docket No. FAA-2006-23578; Directorate Identifier 2006-CE-01-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding the following new AD:

2006-13-15 Mitsubishi Heavy Industries, Ltd.: Amendment 39-14668; Docket No. FAA-2006-23578; Directorate Identifier 2006-CE-01-AD.

Effective Date

Effective Date

(a) This AD becomes effective on August 11, 2006.

Affected ADs

(b) None.

Applicability

(c) This AD affects the following airplane models and serial numbers that are certificated in any category:

Model Serial Nos.

MU-2B-10 … 101 through 120 (Except 102, 114, 115, and 118).

MU-2B-15 … 114, 115, and 118.

MU-2B-20 … 102, and 121 through 238.

MU-2B-25 … 239 through 318 (Except 313), and 313SA.

MU-2B-26 … 319 through 347 (Except 321), and 349SA.

MU-2B-26A … 321SA, 348SA, and 350SA through 394SA (Except 365SA).

MU-2B-30 … 502 through 547.

MU-2B-35 … 548 through 654 (Except 652), and 652SA.

MU-2B-36 … 501, and 655 through 696 (Except 661).

MU-2B-36A … 661SA, and 697SA through 730SA (Except 700SA).

MU-2B-40 … 365SA.

MU-2B-60 … 700SA.

Unsafe Condition

Unsafe Condition

(d) This AD results from a recent safety evaluation that used a data-driven approach to evaluate the design, operation, and maintenance of the MU-2B series airplanes in order to determine their safety and define what steps, if any, are necessary for their safe operation. Part of that evaluation was to identify unsafe conditions that exist or could develop on the affected type design airplanes. The actions specified in this AD are intended to detect and correct cracks, corrosion, fractures, and incorrect torque values in the wing attach barrel nuts, which could result in failure of the wing attach barrel nuts and/or associated wing attachment hardware. This failure could lead to in-flight separation of the outer wing from the center wing section and result in loss of controlled flight.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Actions Compliance Procedures

(1) Remove each wing attach Within the next 200 Follow Mitsubishi

barrel nut, bolt, and hours time-in- Heavy Industries,

retainer and do a visual service or 12 Ltd. MU-2 Service

inspection for cracks, months after August Bulletins

corrosion, and fractures. 11, 2006 (the referenced as JCAB

effective detailed T.C.: No. 241,

date of this AD), dated July 14,

whichever occurs 2004, and FAA T.C.:

first, unless No. 103/57-004A,

already done. dated March 10,

(1) Remove each wing attach Within the next 200 Follow Mitsubishi

2006, as

applicable.

(2) If any signs of cracks, Before further Follow Mitsubishi

corrosion, or fractures are flight after the Heavy Industries,

found on any wing attach inspection required Ltd. MU-2 Service

barrel nut during the in paragraph (e)(1) Bulletins

inspection required in of this AD, unless referenced as JCAB

paragraph (e)(1) of this already done. T.C.: No. 241,

AD, replace that wing dated July 14,

attach barrel nut, bolt, 2004, and FAA T.C.:

and retainer with new parts No. 103/57-004A,

and install to the correct dated March 10,

torque value. 2006, as

applicable, and the

appropriate

maintenance manual.

(3) If no signs of cracks, Before further Follow Mitsubishi

corrosion, or fractures are flight after the Heavy Industries,

found during the inspection inspection required Ltd. MU-2 Service

found during the inspection inspection required Ltd. MU-2 Service

required in paragraph in paragraph (e)(1) Bulletins

(e)(1) of this AD, you may of this AD, unless referenced as JCAB

reuse the wing attach already done. T.C.: No. 241,

barrel nuts and bolts if dated July 14,

they have been inspected 2004, and FAA T.C.:

and are free of deformation No. 103/57-004A,

and irregularities in the dated March 10,

threads and meet the 2006, as

minimum breakaway torque applicable, and the

requirement. Reinstall appropriate

inspected parts to the maintenance manual.

correct torque value. If the wing attach barrel nuts and bolts are not free of deformation and irregularities in the threads or do not meet the minimum breakaway torque requirement, install new parts to the correct torque value.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Fort Worth Airplane Certification Office, FAA, ATTN: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370, has the authority to approve alternative methods of compliance for this AD, if requested using the procedures found in 14 CFR 39.19.

Related Information

Related Information

(g) Mitsubishi Heavy Industries, Ltd. MU-2 Service Bulletins JCAB T.C.: No. 241, dated July 14, 2004, and FAA T.C.: No. 103/57-004A, dated March 10, 2006, pertain to the subject of this AD.

Material Incorporated by Reference

(h) You must do the actions required by this AD following Mitsubishi Heavy Industries, Ltd. MU-2 Service Bulletins referenced as JCAB T.C.: No. 241, dated July 14, 2004, and FAA T.C.: No. 103/ 57-004A, pages 1 and 4 dated March 10, 2006, pages 2, 3, 5, 6, and 7 dated August 2, 2004. The Director of the Federal Register approved the incorporation by reference of this service bulletin in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. To get a copy of this service information, contact Mitsubishi Heavy Industries America, Inc., 4951 Airport Parkway, Suite 800, Addison, Texas 95001; telephone: (972) 934-5480; fax: (972) 934-5488, or Turbine Aircraft Services, Inc., 4550 Jimmy Doolittle Drive, Addison, Texas 75001; telephone: (972) 248-3108; facsimile: (972) 248-3321. To review copies of this service information, go to the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html or call (202) 741-6030. To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-001 or on the Internet at http://dms.dot.gov. The docket number is FAA-2006-23578; Directorate Identifier 2006-CE-01-AD.

Material Incorporated by Reference

Issued in Kansas City, Missouri, on June 19, 2006. James E. Jackson, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.