AD 2005-15-11 BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. This AD requires repetitive detailed and specialized inspections to detect fatigue damage in the fuselage, replacement of certain bolt assemblies, and corrective actions if necessary. This AD results from a review of primary airframe fatigue test results and a Maintenance Steering Group 3 (MSG-3) analysis. We are issuing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
This document is no longer current. Superseded by AD 2023-02-06. Check the official source before relying on it.
[Docket No. FAA-2005-21137; Directorate Identifier 2002-NM-86-AD; Amendment 39-14200; AD 2005-15-11] RIN 2120-AA64
Airworthiness Directives; BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).
Action
ACTION: Final rule.
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. This AD requires repetitive detailed and specialized inspections to detect fatigue damage in the fuselage, replacement of certain bolt assemblies, and corrective actions if necessary. This AD results from a review of primary airframe fatigue test results and a Maintenance Steering Group 3 (MSG-3) analysis. We are issuing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
Dates
DATES: Effective August 30, 2005.
The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of August 30, 2005.
ADDRESSES: You may examine the AD docket on the Internet at http://www.dms.dot.gov or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, Room PL-401, Washington, DC.
Addresses
Contact British Aerospace Regional Aircraft American Support, 13850 Mclearen Road, Herndon, Virginia 20171, for service information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-1175; fax (425) 227-1149.
Supplementary Information
SUPPLEMENTARY INFORMATION:
Examining the Docket
You may examine the AD docket on the Internet at http://www.dms.dot.gov or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the street address stated in the ADDRESSES section.
Discussion
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. That NPRM was published in the Federal Register on May 9, 2005 (70 FR 24326). That NPRM proposed to require repetitive detailed and specialized inspections to detect fatigue damage in the fuselage, replacement of certain bolt assemblies, and corrective actions if necessary.
Comments
Comments
We provided the public the opportunity to participate in the development of this AD. We received no comments on the NPRM or on the determination of the cost to the public.
Conclusion
We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.
Costs of Compliance
Costs of Compliance
The following table provides the estimated costs for U.S. operators to comply with this AD.
Estimated Costs
Cost per Number of
Average airplane, per U.S.-
Action Work hours labor rate Parts inspection registered Fleet cost
per hour cycle airplanes
Inspections of the door structure … 17 $65 None … $1,105 57 Up to $62,985, per inspection
cycle.
Inspections of the fuselage structure.. 164 65 None … 10,660 57 Up to $607,620, per inspection/
replacement cycle.
Inspections of the engine nacelle 4 65 None … 260 57 Up to $14,820, per inspection
structure. cycle.
Inspections of the empennage structure. 14 65 None … 910 57 Up to $51,870, per inspection
cycle.
Inspections of the wing structure … 24 65 None … 1,560 57 Up to $88,920, per inspection
cycle.
In summary, required actions will take about 223 work hours per airplane, at an average labor rate of $65 per work hour. Based on these figures, the estimated cost of the AD for U.S. operators is up to $826,215, or $14,495 per airplane, per inspection cycle.
Authority for This Rulemaking
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
Regulatory Findings
We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a "significant regulatory action" under Executive Order 12866;
(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD):
2005-15-11 BAE Systems (Operations) Limited (Formerly British Aerospace Regional Aircraft): Amendment 39-14200. Docket No. FAA-2005-21137; Directorate Identifier 2002-NM-86-AD.
Effective Date
Effective Date
(a) This AD becomes effective August 30, 2005.
Affected ADs
(b) None.
Applicability: (c) This AD applies to all BAE Systems (Operations) Limited Model Jetstream 4101 airplanes, certificated in any category.
Unsafe Condition
(d) This AD was prompted by a review of primary airframe fatigue test results and a Maintenance Steering Group 3 (MSG-3) analysis. We are issuing this AD to detect and correct fatigue damage of the fuselage, door, engine nacelle, empennage, and wing structures, which could result in reduced structural integrity of the airplane.
Unsafe Condition
Compliance: (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
Service Bulletin Reference
(f) The term "the service bulletin," as used in this AD, means BAE Systems (Operations) Limited Service Bulletin J41-51-001, Revision 2, dated April 30, 2003.
Inspection and Corrective Actions
Inspection and Corrective Actions
(g) At the compliance times specified in the "Initial Compliance Time" column of Tables 1, 2, 3, 4, and 5 of this AD: Do the applicable detailed inspections and specialized inspections to detect fatigue damage, and replacement of certain bolt assemblies, and any applicable corrective actions, in accordance with the Accomplishment Instructions of the service bulletin. Do any corrective action before further flight. Repeat the inspections and replacement thereafter at intervals specified in the "Repetitive Intervals" column of Tables 1, 2, 3, 4, and 5 of this AD.
Note 1: For the purposes of this AD, a detailed inspection is: "An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required."
Table 1.--Appendix 1 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 1 of the "grace period") Repetitive intervals
service bulletin -------------------------------------------------------
Inspection threshold Grace period
1, 6 … Before the accumulation of Within 500 flight At intervals not to
22,500 total flight cycles cycles after the exceed 3,300 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
2 … Before the accumulation of Within 500 flight At intervals not to
20,000 total flight cycles. cycles after the exceed 5,200 flight
effective date of this cycles.
AD.
3, 5, 7 … Before the accumulation of Within 500 flight At intervals not to
21,000 total flight cycles. cycles after the exceed 10,000 flight
effective date of this cycles.
AD.
4 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 26,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
Table 2.--Appendix 2 Compliance Times
Initial compliance time (whichever occurs later
between the times in "inspection threshold" and
Part of actions "grace period")
specified in appendix 1 of the ------------------------------------------------------- Repetitive intervals
service bulletin Inspection/replacement
threshold Grace period
specified in appendix 1 of the ------------------------------------------------------- Repetitive intervals
1, 3, 32 … Within 96 months after the Within 12 months after At intervals not to
date of issuance of the the effective date of exceed 24 months.
original standard this AD.
Airworthiness Certificate
or the date of issuance of
the original Export
Certificate of
Airworthiness, whichever
occurs later.
2 … Before the accumulation of Within 500 flight At intervals not to
23,000 total flight cycles. cycles after the exceed 10,000 flight
effective date of this cycles.
AD.
4, 10, 11, 12, 13 … Before the accumulation of Within 500 flight At intervals not to
20,000 total flight cycles. cycles after the exceed 6,600 flight
effective date of this cycles.
AD..
5 … Within 48 months after the Within 12 months after At intervals not to
date of issuance of the the effective date of exceed 24 months.
original standard this AD.
Airworthiness Certificate
or the date of issuance of
the original Export
Certificate of
Airworthiness, whichever
occurs later.
6 … Before the accumulation of Within 500 flight At intervals not to
20,000 total flight cycles. cycles after the exceed 5,400 flight
effective date of this cycles.
AD.
7 … Before the accumulation of Within 500 flight At intervals not to
22,400 total flight cycles cycles after the exceed 8,200 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
8 … Before the accumulation of Within 500 flight
19,000 total flight cycles. cycles after the
effective date of this
AD.
9 … Before the accumulation of Within 500 flight At intervals not to
23,000 total flight cycles. cycles after the exceed 2,300 flight
effective date of this cycles.
AD.
14 … Before the accumulation of Within 500 flight At intervals not to
19,700 total flight cycles. cycles after the exceed 4,700 flight
effective date of this cycles.
AD.
15 … Before the accumulation of Within 500 flight At intervals not to
25,000 total flight cycles cycles after the exceed 13,600 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
16, 19, 20 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 25,800 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
17, 21, 29, 30 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 30,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
18 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 30,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
22 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 16,500 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
23 … Before the accumulation of Within 500 flight At intervals not to
22,000 total flight cycles cycles after the exceed 7,400 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
24 … Before the accumulation of Within 500 flight At intervals not to
23,600 total flight cycles cycles after the exceed 15,700 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
25 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 12,700 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
26 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 21,800 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
27 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 18,300 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
28 … Between 20,000 and 26,000 Within 500 flight At intervals not to
total flight cycles. cycles after the exceed 9,500 flight
effective date of this cycles.
AD.
31 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 16,300 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
33 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles. cycles after the exceed 26,000 flight
effective date of this cycles.
AD.
Table 3.--Appendix 3 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 3 of the "grace period") Repetitive intervals
service bulletin -------------------------------------------------------
Inspection threshold Grace period
1, 2 … Before the accumulation of Within 500 flight At intervals not to
24,000 total flight cycles cycles after the exceed 11,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
Table 4.--Appendix 4 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 4 of the "grace period") Repetitive intervals
service bulletin -------------------------------------------------------
Inspection threshold Grace period
1 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 12,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
2 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 30,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
3, 5 … Within 48 months after the Within 12 months after At intervals not to
date of issuance of the the effective date of exceed 48 months.
original standard this AD.
Airworthiness Certificate
or the date of the issuance
of the original Export
Certificate of
Airworthiness, whichever
occurs later.
4, 6 … 96 months after the date of Within 12 months after At intervals not to
issuance of the original the effective date of exceed 48 months.
standard Airworthiness this AD.
Certificate or the date of
issuance of the original
Export Certificate of
Airworthiness, whichever
occurs later.
Table 5.--Appendix 5 Compliance Times
Initial compliance time (whichever occurs later
Part of actions between the times in "inspection threshold" and
specified in appendix 5 of the "grace period") Repetitive intervals
service bulletin -------------------------------------------------------
Inspection threshold Grace period
1, 7 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 30,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
2, 5, 6 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 9,000 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
3, 4 … Before the accumulation of Within 500 flight At intervals not to
26,000 total flight cycles cycles after the exceed 7,900 flight
and after the accumulation effective date of this cycles.
of 20,000 total flight AD.
cycles.
Repairs for Damage Beyond Service Bulletin Limits
Repairs for Damage Beyond Service Bulletin Limits
(h) If any fatigue damage is found that exceeds the limits specified in the service bulletin: Before further flight, repair the damage according to a method approved by either the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate; or the Civil Aviation Authority (or its delegated agent).
Previous Actions
Previous Actions
(i) Actions done before the effective date of this AD in accordance with BAE Systems (Operations) Limited Service Bulletin J41-51-001, dated February 15, 2002; or Revision 1, dated August 7, 2002; are acceptable for compliance with the requirements of paragraphs (g) and (h) of this AD.
No Report Required
No Report Required
(j) Although the service bulletin referenced in this AD specifies to submit certain information to the manufacturer, this AD does not include that requirement.
Alternative Methods of Compliance (AMOCs)
(k) The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.
Related Information
Related Information
(l) British airworthiness directive 005-02-2002 also addresses the subject of this AD.
Material Incorporated by Reference
(m) You must use BAE Systems (Operations) Limited Service Bulletin J41-51-001, Revision 2, dated April 30, 2003, to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference of this document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact British Aerospace Regional Aircraft American Support, 13850 Mclearen Road, Herndon, Virginia 20171, for a copy of this service information. You may review copies at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Room PL-401, Nassif Building, Washington, DC; on the internet at http://dms.dot.gov; or at the National Archives and Records Administration (NARA). For information on the availability of this material at the NARA, call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of --federal--regulations/ibr--locations.html.
Material Incorporated by Reference
Issued in Renton, Washington, on July 14, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service.