Radar Vectors
Airworthiness Directive Current Issued Mar 11, 2005 5 pages Copy saved Nov 17, 2026

AD 2005-05-19 Boeing Model 727 Airplanes

The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 727 airplanes. That AD currently requires repetitive detailed inspections to detect cracking, corrosion, and existing stop-drilled repairs of cracking in the upper chord of the rear spar of the wing; and repair if necessary. This new AD requires new repetitive inspections to detect cracks, corrosion, minor surface defects, and existing stop-drilled repairs of cracks in the upper and lower chords of the front and rear spars of the wing; and repair if necessary. This AD is prompted by our determination that further rulemaking action is necessary to require additional actions specified in the referenced service bulletin. We are issuing this AD to prevent structural failure of the wing and fuel leaks in the airplane due to stress corrosion cracking of the wing spar chords.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2004-19530; Directorate Identifier 2002-NM-274-AD; Amendment 39-14008; AD 2005-05-19] RIN 2120-AA64

Airworthiness Directives; Boeing Model 727 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Final rule.

Summary

SUMMARY: The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 727 airplanes. That AD currently requires repetitive detailed inspections to detect cracking, corrosion, and existing stop-drilled repairs of cracking in the upper chord of the rear spar of the wing; and repair if necessary. This new AD requires new repetitive inspections to detect cracks, corrosion, minor surface defects, and existing stop-drilled repairs of cracks in the upper and lower chords of the front and rear spars of the wing; and repair if necessary. This AD is prompted by our determination that further rulemaking action is necessary to require additional actions specified in the referenced service bulletin. We are issuing this AD to prevent structural failure of the wing and fuel leaks in the airplane due to stress corrosion cracking of the wing spar chords.

Dates

DATES: This AD becomes effective April 15, 2005.

On December 18, 2002 (67 FR 71808, December 3, 2002), the Director of the Federal Register approved the incorporation by reference of Boeing Alert Service Bulletin 727-57A0145, Revision 2, dated October 24, 2002.

ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207.

Addresses

Docket: The AD docket contains the proposed AD, comments, and any final disposition. You can examine the AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the U.S. Department of Transportation, 400 Seventh Street SW, room PL-401, Washington, DC. This docket number is FAA-2004-19530; the directorate identifier for this docket is 2002-NM-274-AD.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Daniel F. Kutz, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 917-6456; fax (425) 917-6590.

SUPPLEMENTARY INFORMATION: The FAA proposed to amend part 39 of the Federal Aviation Regulations (14 CFR Part 39) with an AD to supersede AD 2002-24-05, amendment 39-12970 (67 FR 71808, December 3, 2002). The existing AD applies to certain Boeing Model 727 airplanes. The proposed AD was published in the Federal Register on November 5, 2004 (69 FR 64506), to require new repetitive inspections to detect cracks, corrosion, minor surface defects, and existing stop-drilled repairs of cracks in the upper and lower chords of the front and rear spars of the wing; and repair if necessary.

Comments

Comments

We provided the public the opportunity to participate in the development of this AD. We have considered the comment that has been submitted on the proposed AD. The commenter supports the proposed AD.

Explanation of Change to Model Designation

We have revised the subject heading of the existing AD to identify model designations as published in the most recent type certificate data sheet for the affected models.

Changes to Delegation Authority

Changes to Delegation Authority

Boeing has received a Delegation Option Authorization (DOA). We have revised this final rule to delegate the authority to approve an alternative method of compliance for any repair required by this AD to the Authorized Representative for the Boeing DOA Organization rather than the Designated Engineering Representative (DER).

Conclusion

Conclusion

We have carefully reviewed the available data, including the comment that has been submitted, and determined that air safety and the public interest require adopting the AD with the change described previously. We have determined that this change will neither increase the economic burden on any operator nor increase the scope of the AD.

Costs of Compliance

Costs of Compliance

There are about 1,426 airplanes of the affected design in the worldwide fleet. This AD will affect about 946 airplanes of U.S. registry.

For Group 1 airplanes identified in the service bulletin, the actions (Part 1 of the Accomplishment Instructions of the service bulletin) that are required by AD 2002-24-05 and retained in this AD take about 8 work hours per airplane, at an average labor rate of $65 per work hour. Based on these figures, the estimated cost of the currently required actions is $520 per airplane.

The following table provides the estimated costs for U.S. operators to comply with the new actions required by this AD. The average labor rate is $65 per work hour.

Estimated Costs

Per airplane

cost, per

For airplanes identified in the service bulletin as-- Actions in-- Work hours-- inspection

cycle--

Group 1 … Part 2 of the Accomplishment 30 $1,950

Instructions of the service

bulletin.

Group 1 … Part 3 of the Accomplishment 21 1,365

Instructions of the service

bulletin.

Group 1 … Part 4 of the Accomplishment 68 4,420

Instructions of the service

bulletin.

Group 1 … Part 8 of the Accomplishment 8 520

Instructions of the service

bulletin.

Group 1 … Part 9 of the Accomplishment 30 1,950

Instructions of the service

bulletin.

Group 2 … Part 5 of the Accomplishment 52 3,380

Instructions of the service

bulletin.

Group 2 … Part 6 of the Accomplishment 110 7,150

Instructions of the service

bulletin.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a "significant regulatory action" under Executive Order 12866;

(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD. See the ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing amendment 39-12970 (67 FR 71808, December 3, 2002), and by adding the following new airworthiness directive (AD):

§ 39.13 [Amended]

2005-05-19 Boeing: Amendment 39-14008. Docket No. FAA-2004-19530; Directorate Identifier 2002-NM-274-AD.

Effective Date

(a) This AD becomes effective April 15, 2005.

Affected ADs

(b) This AD supersedes AD 2002-24-05, amendment 39-12970.

Applicability

(c) This AD applies to Boeing Model 727, 727C, 727-100, -100C, - 200, and -200F series airplanes, line numbers 1 through 1832 inclusive; certificated in any category.

Unsafe Condition

Unsafe Condition

(d) This AD was prompted by our determination that further rulemaking action is necessary to require additional actions specified in the referenced service bulletin. We are issuing this AD to prevent structural failure of the wing and fuel leaks in the airplane due to stress corrosion cracking of the wing spar chords.

Compliance

Compliance

(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

Service Bulletin References

(f) The term "the service bulletin," as used in this AD, means Boeing Alert Service Bulletin 727-57A0145, Revision 2, dated October 24, 2002.

Inspection Requirements of AD 2002-24-05, Amendment 39-12970

Inspection Requirements of AD 2002-24-05, Amendment 39-12970

Inspection

(g) For airplanes specified as "Group 1" airplanes in the service bulletin: Within 20 years after the date of manufacture or within 90 days after December 18, 2002 (the effective date of AD 2002-24-05, amendment 39-12970), whichever occurs later, perform an external detailed inspection for cracking, corrosion, and existing stop-drilled repairs of cracking in the upper chord on the rear spar from Wing Butt Line (WBL) 70.5 through WBL 249.3, per the service bulletin, paragraph 3.B, "Work Instructions," Part 1. Thereafter, repeat the inspection at intervals not to exceed 2 years.

Inspection

Note 1: For the purposes of this AD, a detailed inspection is "an intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc., may be necessary. Surface cleaning and elaborate procedures may be required."

New Actions Required by This AD

New Actions Required by This AD

Inspections Specified in Parts 2 Through 6, and 8 and 9 of the Service Bulletin

(h) Accomplish the applicable inspection(s) specified in paragraphs (h)(1) through (h)(7) of this AD at the later of the applicable times specified in the "Threshold" and "Grace Period" columns in Table 1 of this AD, and repeat the inspection(s) at the time specified in the "Repetitive Interval" column of Table 1 of this AD. Accomplishment of the inspection required by paragraph (h)(1) of this AD terminates the repetitive inspection requirements of paragraph (g) of this AD.

Inspections Specified in Parts 2 Through 6, and 8 and 9 of the Service Bulletin

Table 1.--Compliance Times for Inspections Specified in Parts 2 Through 6, and 8 and 9 of Service Bulletin

For airplanes identified in the Repetitive

service bulletin as-- Threshold-- Grace period-- interval-- Do--

(1) Group 1 … Before 20 years Within 1 year None … A high frequency

since the date of after the eddy current

issuance of the effective date of (HFEC) inspection

original this AD. and detailed

Airworthiness inspection of the

Certificate or upper chord the

the date of rear spar from

issuance of the WBL 70.5 to the

original Export wing tip for

Certificate of cracks,

Airworthiness. corrosion, minor

surface defects,

and existing stop-

drilled repairs

of cracking, in

accordance with

paragraph 3.B.,

Work

Instructions,

Part 2, of the

Accomplishment

Instructions of

the service

bulletin.

(2) Group 1 … Before 20 years Within 2 years At intervals not A detailed

since the date of after the to exceed 2 years. inspection of the

issuance of the effective date of upper and lower

original this AD. chord of the

Airworthiness front spar and

Certificate or the lower chord

the date of of the rear spar

issuance of the from WBL 70.5 to

Original Export the wing tip for

Certificate of cracks,

Airworthiness. corrosion, minor

surface defects,

and existing stop-

drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 3, of the

Accomplishment

Instructions of

the service

bulletin.

(3) Group 1 … Before 20 years Within 4 years At intervals not An HFEC inspection

since the date of after the to exceed 4 years. of the upper and

issuance of the effective date of lower chords of

original this AD. the rear spar

Airworthiness from WBL 70.5 to

Certificate or the wing tip for

the date of cracks,

issuance of the corrosion, minor

original Export surface defects,

Certificate of and existing stop-

Airworthiness. drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 4, of the

Accomplishment

Instructions of

the service

bulletin.

(4) Group 1 … Within 2 years None … At intervals not A detailed

after doing the to exceed 2 years. inspection of the

actions required upper chord of

by paragraph the rear spar WBL

(h)(1) of this AD. 70.5 to the wing

tip for cracks,

corrosion, minor

surface defects,

and existing stop-

drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 8, of the

Accomplishment

Instructions of

the service

bulletin.

(5) Group 1 … Within 4 years None … At intervals not An HFEC inspection

after doing the to exceed 4 years. of doing the not

actions required to the upper

by paragraph chord actions

(h)(1) of this AD. exceed 4 of the

rear spar

required by years

from WBL 70.5 to

paragraph the

wing tip for

(h)(1) of cracks,

this AD

corrosion, minor

surface defects,

and existing stop-

drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 9, of the

Accomplishment

Instructions of

the service

bulletin.

(6) Group 2 … Before 20 years Within 2 years At intervals not An exterior

since the date of after the to exceed 2 years. detailed

issuance of the effective date of inspection of the

original this AD. upper and lower

Airworthiness chords of the

Certificate or front and rear

the date of spars from WBL

issuance of the 70.5 to the wing

original Export tip for cracks,

Certificate of corrosion, minor

Airworthiness. surface defects,

and existing stop-

drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 5, of the

Accomplishment

Instructions of

the service

bulletin.

(7) Group 2 … Before 20 years Within 4 years At intervals not An HFEC inspection

since the date of after the to exceed 4 years. of the upper and

issuance of the effective date of lower chords of

original this AD. the front and

Airworthiness rear spars from

Certificate or WBL 70.5 to the

the date of wing tip for

issuance of the cracks,

original Export corrosion, minor

Certificate of surface defects,

Airworthiness. and existing stop-

drilled repairs

of cracking

(initial

inspection only),

in accordance

with paragraph

3.B., Work

Instructions,

Part 6, of the

Accomplishment

Instructions of

the service

bulletin.

Corrective Actions

Corrective Actions

(i) If any crack, corrosion, or minor surface defect is detected during any inspection required by this AD, before further flight, do the applicable corrective actions in accordance with Part 7 of the Accomplishment Instructions of the service bulletin, except as provided by paragraph (j) of this AD.

(j) If any crack or corrosion is detected during any inspection required by this AD that exceeds the limits specified in the service bulletin, and the bulletin specifies to contact Boeing for appropriate action: Before further flight, repair in accordance with a method approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA; or in accordance with data meeting the certification basis of the airplane approved by an Authorized Representative for the Boeing Delegation Option Authorization Organization who has been authorized by the Manager, Seattle ACO, to make such findings. For a repair method to be approved, the approval must specifically reference this AD.

(k) If any existing stop-drilled repair of previous cracking is detected during any inspection required by this AD, before further flight, permanently repair crack in accordance with paragraph 3.B., Work Instructions, Part 7, paragraph 2., "Crack Repair" of the Accomplishment Instructions of the service bulletin.

(l) Before further flight following any inspection or repair required by this AD, apply a wet layer of BMS 3-23 organic corrosion inhibiting compound or Boeing equivalent, in accordance with the Accomplishment Instructions of the service bulletin.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(m)(1) The Manager, Seattle ACO, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19.

(2) Alternative methods of compliance, approved previously in accordance with AD 2002-24-05, amendment 39-12970, are approved as alternative methods of compliance with this AD.

(3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD, if it is approved by an Authorized Representative for the Boeing Delegation Option Authorization Organization who has been authorized by the Manager, Seattle ACO, to make such findings. For a repair method to be approved, the approval must specifically reference this AD.

Material Incorporated by Reference

Material Incorporated by Reference

(n) You must use Boeing Alert Service Bulletin 727-57A0145, Revision 2, dated October 24, 2002, to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register previously approved the incorporation by reference of this document as of December 18, 2002 (67 FR 71808, December 3, 2002). For copies of the service information, contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207. For information on the availability of this material at the National Archives and Records Administration (NARA), call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. You may view the AD docket at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW, room PL-401, Nassif Building, Washington, DC.

Issued in Renton, Washington, on March 2, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service.