Radar Vectors
Airworthiness Directive Current Issued Aug 13, 2004 7 pages Copy saved Nov 17, 2026

AD 2004-17-01 Cessna Aircraft Company Models 208 and 208B Airplanes

The FAA supersedes Airworthiness Directive (AD) AD 2002-22-17, which applies to all Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes; and AD 2003-21-04, which applies to certain Cessna Models 208 and 208B airplanes. This AD requires you to repetitively inspect the flap bellcranks for cracks and eventually replace these bellcranks. The installation of a newly designed bellcrank to increase the life limits is terminating action for the repetitive inspections. This AD is the result of these developments: Since FAA issued AD 2002-22-17 and AD 2003-21-04, Cessna designed a new flap bell crank with a life limit of 40,000 landings instead of 7,000 landings. Also, FAA has done more analysis and examination of cracks and missing/incomplete welds in all of the bell cranks. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 2002-CE-23-AD; Amendment 39-13772; AD 2004-17-01] RIN 2120-AA64

Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

SUMMARY: The FAA supersedes Airworthiness Directive (AD) AD 2002-22-17, which applies to all Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes; and AD 2003-21-04, which applies to certain Cessna Models 208 and 208B airplanes. This AD requires you to repetitively inspect the flap bellcranks for cracks and eventually replace these bellcranks. The installation of a newly designed bellcrank to increase the life limits is terminating action for the repetitive inspections. This AD is the result of these developments: Since FAA issued AD 2002-22-17 and AD 2003-21-04, Cessna designed a new flap bell crank with a life limit of 40,000 landings instead of 7,000 landings. Also, FAA has done more analysis and examination of cracks and missing/incomplete welds in all of the bell cranks. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

Dates

DATES: This AD becomes effective on September 26, 2004.

As of December 31, 2002 (67 FR 68508, November 12, 2002), the Director of the Federal Register approved the incorporation by reference of Cessna Service Bulletin No. CAB02-1, dated February 11, 2002.

As of October 21, 2003 (68 FR 59707, October 17, 2003), the Director of the Federal Register approved the incorporation by reference of the following:

Cessna Caravan Service Bulletin No.: CAB03-11, Revision 1, dated September 24, 2003; Cessna Caravan Service Bulletin No.: CAB02-12, revision 1, dated January 27, 2003; and Cessna Caravan Service Kit No.: SK208-148A, dated January 27, 2003 (Original issue: October 21, 2002).

Addresses

ADDRESSES: You may get the service information identified in this AD from Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67277; telephone: (316) 517-5800; facsimile: (316) 942-9006.

You may view the AD docket at FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2002-CE-23-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Office hours are 8 a.m. to 4 p.m., Monday through Friday, except Federal holidays.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Paul Nguyen, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4125; facsimile: 816-946-4107.

SUPPLEMENTARY INFORMATION:

Discussion

What events have caused this AD? The need to reduce the life limit and repetitively inspect the inboard forward flap bellcrank on Cessna Models 208 and 208A airplanes caused us to issue AD 2002-22-17, Amendment 39-12944 (67 FR 68508, November 12, 2002); and AD 2003-21-04, Amendment 39-13339 (68 FR 59707, October 17, 2003).

Discussion

Since FAA issued AD 2002-22-17 and AD 2003-21-04, Cessna has designed a new flap bellcrank, part number (P/N) 2622311-7, with a life limit of 40,000 landings (instead of 7,000 landings). The new flap bellcrank (P/N 2622311-7) may be substituted for the older flap bellcranks, P/N 2622281-2, 2622281-12, or 2692001-2. Installation of this new flap bellcrank will eliminate the need for repetitive inspections.

What is the potential impact if FAA took no action? Cracks in the bellcrank could result in failure of this part. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

Has FAA taken any action to this point? We issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to all Cessna Models 208 and 208B airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on July 28, 2003 (68 FR 44252). The NPRM proposed to revise AD 2002-22-17 by proposing a new AD that would:

--Retain the actions from AD 2003-21-04, and add all flap bellcranks to the applicability; --Retain the requirements of AD 2002-22-17; and --Provide the option of installing the 40,000 landings life limit bellcranks.

Comments

Was the public invited to comment? We provided the public the opportunity to participate in developing this AD. The following presents the comments received on the proposal and FAA's response to each comment:

Comment Issue No. 1: Identify the New Flap Bellcrank (Part Number (P/N) 2622311-16)

Comment Issue No. 1: Identify the New Flap Bellcrank (Part Number (P/N) 2622311-16)

What is the commenter's concern? The commenter writes that including by P/N this new flap bellcrank, which has a 40,000 landings life limit, in paragraph (f)(2)(ii) of the AD would be a good idea. We conclude that the commenter wants this specific bellcrank identified by part number to make this an obvious alternative bellcrank.

What is FAA's response to the concern? We are not incorporating the commenter's recommendation because the proposal already identifies the intent. The FAA already allows installation of any new design flap bellcrank by the words "* * *Or FAA approved equivalent P/N." If we included this P/N, we would be obligated to revise the AD every time a new part was designed including part manufacturer approvals (PMAs).

Therefore, we are not changing the final rule AD action based on this comment.

Comment Issue No. 2: Allow Welding of Any Bellcrank With Missing Welds

Comment Issue No. 2: Allow Welding of Any Bellcrank With Missing Welds

What is the commenter's concern? The commenter recommends that FAA change the AD to allow welding of the bellcrank following Cessna Caravan Service Bulletin CAB03-11, Revision 1, dated September 24, 2003, except for the right hand inboard forward bellcrank. The commenter writes that this welding should be allowed since Cessna identifies welding in the above service bulletin.

What is FAA's response to the concern? The FAA disagrees with the commenter's recommendation. The FAA has determined that the unsafe condition is prevented through inspection of the applicable Bellcranks, with necessary replacements.

Therefore, we are not changing the final rule AD action based on this comment.

Comment Issue No. 3: Include Visual Inspection of the Aileron Bellcrank

Comment Issue No. 3: Include Visual Inspection of the Aileron Bellcrank

What is the commenter's concern? The commenter recommends that in this AD that FAA allow inspection of the aileron bellcrank since Cessna Caravan Service Bulletin CAB04-3 requires visual inspection of the aileron bellcrank.

What is FAA's response to the concern? We disagree with the commenter's recommendation. Based on FAA's evaluation to this point, the unsafe condition is prevented through the inspections specified in the AD, with necessary replacement. The FAA will consider alternative methods of compliance (AMOC) on a case-by-case basis.

We are not changing the final rule AD action based on this comment.

Conclusion

Conclusion

What is FAA's final determination on this issue? We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for the changes discussed above and minor editorial corrections. We have determined that these changes and minor corrections:

--Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and --Do not add any additional burden upon the public than was already proposed in the NPRM.

Changes to 14 CFR Part 39--Effect on the AD

Changes to 14 CFR Part 39--Effect on the AD

How does the revision to 14 CFR part 39 affect this AD? On July 10, 2002, the FAA published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs the FAA's AD system. This regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.

Costs of Compliance

Costs of Compliance

How many airplanes does this AD impact? We estimate that this AD affects 1,300 airplanes in the U.S. registry.

What is the cost impact of this AD on owners/operators of the affected airplanes? For the actions retained from AD 2003-21-04, and the addition of all bellcranks to the applicability, we estimate the following costs to do this inspection:

Total cost per

Labor cost Parts cost airplane Total cost on U.S. operators

2 workhours x $65 per hour = $130. No cost for parts... $130 $130 x 1,300 = $169,000

We estimate the following costs to do any necessary replacements of the right inboard forward flap bellcrank (P/N 2622311-7, alternate P/N 2622311-16) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

3 workhours x $65 per hour = $195 … $1,845 $195 + $1,845 = $2,040

We estimate the following costs to do any necessary replacements of the left inboard forward flap bellcrank (P/N 2622281-1) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $1,201 $65 + $1,201 = $1,266

We estimate the following costs to do any necessary replacements of the right inboard aft flap bellcrank (P/N 2622267-8) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $1,273 $65 + $1,273 = $1,338

We estimate the following costs to do any necessary replacements of the left inboard aft flap bellcrank (P/N 2622267-7) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $2,098 $65 + $2,098 = $2,163

We estimate the following costs to do any necessary replacements of the left outboard flap bellcrank (P/N 2622091-17) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $627 $65 + $627 = $692

We estimate the following costs to do any necessary replacements of the right outboard flap bellcrank (P/N 2622091-18) that would be required based on the results of this inspection. We have no way of determining the number of airplanes that may need this replacement:

Labor cost Parts cost Total cost per airplane

1 workhour x $65 per hour = $65 … $661 $65 + $627 = $726

For the requirements from AD 2002-22-17 that you repetitively inspect the inboard forward flap bellcranks for cracks, eventually replace these bellcranks, and provides the option of installing the new design flap bellcrank to increase the life limits and terminate the repetitive inspections, we estimate the following costs to do the inspection:

Total cost per

Labor cost Parts cost airplane Total cost on U.S. operators

1 workhour x $65 per hour = $65... No cost for parts... $65 $65 x 1,300 = $84,500

We estimate the following costs to do any replacements using the same flap bellcrank (P/N 2622281-2, 2622281-12, 2692001-2, or FAA-approved equivalent P/N) that will be required based on the inspection or the reduced life limits:

Labor cost Parts cost Total cost per airplane Total cost on U.S. operators

3 workhours x $65 per hour = $195 … $1,793 $195 + $1,793 = $1,988 $1,988 x 1,300 = $2,584,400

We estimate the following costs to do any replacements using the new flap bellcrank (P/N 2622311-7 or FAA-approved equivalent P/N) that will be required based on the inspection or the reduced life limits. We have no way of determining the number of airplanes that may need this replacement with the new flap bellcrank:

Labor cost Parts cost Total cost per airplane

3 workhours x $65 per hour = $195 … $1,845 $195 + $1,845 = $2,040

Regulatory Findings

Regulatory Findings

Will this AD impact various entities? We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

Will this AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a summary of the costs to comply with this AD and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include "AD Docket No. 2002-CE-23-AD" in your request.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by removing Airworthiness Directive (AD) 2002-22-17, amendment 39-12944 (67 FR 68508, November 12, 2002), and AD 2003-21-04, amendment 39-13339 (68 FR 59707, October 17, 2003); and by adding a new AD to read as follows:

§ 39.13 [Amended]

2004-17-01 Cessna Aircraft Company: Amendment 39-13772; Docket No. 2002-CE-23-AD; Supersedes AD 2002-22-17, amendment 39-12944; and AD 2003-21-04, amendment 39-13339.

When Does This AD Become Effective?

(a) This AD becomes effective on September 26, 2004.

What Other ADs Are Affected by This Action?

What Other ADs Are Affected by This Action?

(b) This AD supersedes AD 2002-22-17, amendment 39-12944; and AD 2003-21-04, amendment 39-13339.

What Airplanes Are Affected by This AD?

(c) This AD affects the following airplane models and serial numbers that are certificated in any category:

(1) Group 1 (retains the actions from AD 2003-21-04, and adds all flap bellcranks to the applicability):

What Airplanes Are Affected by This AD?

Model Serial Nos.

208 … 20800001 through 20800369.

208B … 208B0001 through 208B1014, 208B1017,

208B1018, 208B1020 through

208B1024, 208B1026, and 208B1029

through 208B1033.

(2) Group 2 (retains the requirement of AD 2002-22-17 that you repetitively inspect the inboard forward flap bellcranks for cracks, eventually replace these bellcranks, and provides the option of installing the new design flap bellcrank to increase the life limits and terminate the repetitive inspections): Models 208 and 208B airplanes, all serial numbers.

What Is the Unsafe Condition Presented in This AD?

What Is the Unsafe Condition Presented in This AD?

(d) This AD is the result of (since FAA issued AD 2002-22-17) Cessna's design of a new flap bell crank with a life limit of 40,000 landings (instead of 7,000 landings), and (since FAA issued AD 2003-21-04) further analysis and examination of cracks and missing/ incomplete welds in all of the bell cranks. The actions specified in this AD are intended to prevent failure of any bellcrank due to cracks, deformation, or missing/incomplete welds. This failure could lead to damage to the flap system and surrounding structure and result in reduced or loss of control of the airplane.

What Must I Do To Address This Problem for Group 1 Airplanes?

What Must I Do To Address This Problem for Group 1 Airplanes?

(e) To address this problem for Group 1 airplanes, you must do the following:

Actions Compliance Procedures

(1) Inspect the right inboard Within the next 25 Use a flashlight

forward flap bellcrank assembly landings after and a mirror as

for cracks, deformation, and October 21, 2003 necessary to see

missing/incomplete welds. The (the effective if welds (1),

affected flap bellcrank date of AD 2003- (4), (5), and (6)

incorporates one of the 21-04). If exist and are at

following part numbers (P/N): landings are least 0.06-inch

(i) P/N 2622083-18; … unknown, then you thick around the

(ii) P/N 2622281-2; … may multiply full

(iii) P/N 2692001-2; or … hours time-in- circumference of

(iv) P/N 2622281-12 … service (TIS) by the shaft. These

1.25. For the welds and the

purposes of this inspection

AD, you may procedures are

substitute 20 referenced in

hours TIS for 25 Figure 1, details

landings. A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

No.: CAB03-11,

Revision 1, dated

September 24,

2003.

(2) Inspect the left inboard Within the next 25 Use a flashlight

forward bellcrank for cracks, landings after and a mirror as

deformation, and missing/ September 26, necessary to see

incomplete welds. The affected 2004, the if welds (1)

flap bellcrank incorporates one effective date of through (4) exist

flap bellcrank incorporates one effective date of through (4) exist

of the following part P/Ns: this AD. If and are at least

(i) P/N 262283-15; or … landings are 0.06-inch thick

(ii) P/N 262281-1 … unknown, then you around the full

may multiply circumference of

hours TIS by the shaft. These

1.25. For the welds and the

purposes of this inspection

AD, you may procedures are

substitute 20 referenced in

hours TIS for 25 Figure 2, details

landings. A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

No.: CAB03-11,

Revision 1, dated

September 24,

2003.

(3) Inspect the inboard aft Within the next 25 Use a flashlight

bellcrank for cracks, landings after and a mirror as

deformation, and missing/ September 26, necessary to see

incomplete welds. The affected 2004, the if welds (1),

flap bellcrank incorporates one effective date of (2), (4), and (5)

flap bellcrank incorporates one effective date of (2), (4), and (5)

of the following P/Ns: this AD. If exist and are at

(i) P/N 2622267-1; or … landings are least 0.05-inch

(ii) P/N 2622267-2; … unknown, then you thick around the

(iii) P/N 2622267-7; … may multiply full

(iv) P/N 2622267-8; … hours TIS by circumference of

(v) P/N 2622083-1; or … 1.25. For the the shaft. These

(vi) P/N 2622083-2 … purposes of this welds and the

AD, you may inspection

substitute 20 procedures are

hours TIS for 25 referenced in

landings. Figure 3, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

No.: CAB03-11,

Revision 1, dated

September 24,

2003.

(4) Inspect the outboard Within the next 25 Use a flashlight

bellcrank for cracks, landings after and a mirror as

deformation, and missing/ September 26, necessary to see

incomplete welds. The affected 2004, the if welds (1)

flap bellcrank incorporates one effective date of through (4) exist

flap bellcrank incorporates one effective date of through (4) exist

of the following P/Ns: this AD. If lands and are at least

(i) P/N 2622091-1; or … are unknown, then 0.05-inch thick

(ii) P/N 2622091-2; … you may multiply around the full

(iii) P/N 2622091-9; … hours TIS by circumference of

(iv) P/N 2622091-10; … 1.25. For the the shaft. These

(v) P/N 2622091-17; or … purposes of this welds and the

(vi) P/N 2622091-28 … AD, you may inspection

substitute 20 procedures are

hours TIS for 25 referenced in

landings. Figure 4, details

A, B, and C; and

Views A-A and B-B

of Cessna Caravan

Service Bulletin

No.: CAB03-11,

Revision 1, dated

September 24,

2003.

(5) If you find cracks, Replace or do the Replacement: Use

deformation, or missing/ flap prohibition the

incomplete welds during the actions before Accomplishment

inspection required by further flight Instructions of

paragraphs (e)(1) through after the Cessna Caravan

(e)(4) of this AD, then do one inspection Service bulletin

of the following: required in No.: CAB02-12,

(1) Replace the bellcrank with a paragraphs (e)(1) Revision 1, dated

(1) Replace the bellcrank with a paragraphs (e)(1) Revision 1, dated

new bellcrank; or. through (e)(4) of January 27, 2003,

(ii) Prohibit the use of flaps this AD. If you and the

through the actions of choose the flap Accomplishment

paragraph (g) of this AD.. prohibition, you Instructions of

must have the Cessna Caravan

replacement done Service Kit No.:

within 200 hours SK208-148A, dated

TIS after the January 27, 2003,

inspection or refer to the

required by Maintenance

paragraphs (e)(1) Manual, Chapter

through (e)(4) of 27, Flap System--

this AD. After Maintenance

the new flap Practices, for

bellcrank is bellcrank removal

installed, the and installation

Temporary procedures.

Revision Flap Prohibition:

208PHTR02, dated Use the

September 23, information in

2003, should be the Temporary

removed. Revision

208PHTR02, dated

September 23,

2003. The action

is referenced in

Cessna Caravan

Service Bulletin

No.: CAB03-11,

Revision 1, dated

September 24,

2003.

What Must I Do To Address This Problem for Group 2 Airplanes?

What Must I Do To Address This Problem for Group 2 Airplanes?

(f) To address this problem for Group 2 airplanes, you must do the following:

Actions Compliance Procedures

(1) Repetitive Inspections: Initially inspect Follow the

Inspect, using eddy current upon the Inspection

method, any inboard forward accumulation of Instructions of

flap bellcrank (P/N 2622281-2, 4,000 landings on Cessna Caravan

2622281-12, 2692001-2, or FAA- the bellcrank or Service Bulletin

approved equivalent P/N) for within the next No.: CAB02-1,

cracks. 250 landings dated February

after December 11, 2002, and the

31, 2002 (the applicable

effective date of maintenance

AD 2002-22-17), manual.

whichever occurs

later.

Repetitively

inspect

thereafter at

every 500

landings until

7,000 landings

are accumulated

at which time you

must replace as

required in

paragraphs (f)(2)

and (f)(3) of

this AD. No

repetitive

inspections are

required when a P/

N 2622311-7 (or

FAA-approved

equivalent P/N)

inboard forward

flap bellcrank is

installed.

(2) Initial Replacement: Replace If cracks are Replacement: For

any inboard forward flap found, replace or flap bellcrank (P/

bellcrank (P/N 2622281-2, do the flap N 2622281-2,

2622281-12, 2692001-2, or FAA- prohibition 2622281-12,

approved equivalent P/N) with actions before 2692001-2, or FAA-

either: further flight approved

(i) a new flap bellcrank with after the equivalent P/N):

the same P/N 2622281-2, 26228- inspection Follow the

12, 269001-2, or FAA-approved required in Instructions of

or equivalent P/N; or. paragraphs (f)(1) Cessna Caravan

(ii) a new flap bellcrank (P/M of this AD. If Service Bulletin

262231-7 or FAA-approved you choose the No.: CAB02-1,

equivalent P/N).. flap prohibition, dated February

you must have the 11, 2002, and the

replacement done applicable

within 200 hours maintenance

TIS after the manual. For new

inspection flap bellcrank (P/

required by N 2622311-7 or

paragraphs (f)(1) FAA-approved

of this AD. After equivalent P/N):

the new flap Follow the

bellcrank is Accomplishment

installed, the Instructions of

Temporary Cessna Caravan

Revision Service Bulletin

208PHTR02, dated No.: CAB02-12,

September 23, Revision 1, dated

2003, should be January 27, 2003,

removed. If and the

cracks are not Accomplishment

found, initially Instructions of

replace at Cessna Caravan

whichever occurs Service Kit No.:

later: upon the SK208-148A, dated

accumulation of January 27, 2003.

7,000 landings on Flap

the bellcrank or Prohibitions: Use

within the next the information

75 landings after in the Temporary

December 31, 2002 Revision

(the effective 208PHTR02, dated

date of AD 2002- September 23,

22-17). 2003.

(3) Life Limits (Repetitive Replace at the Use the service

Replacements):. applicable information

(i) The life limit for the referenced life referenced in

inboard forward flap bellcranks limits. paragraph (f)(2)

(P/N 2622281-2, 2622281-12, of this AD.

2692001-2, or FAA-approved equivalent P/N) is 7,000 landings. Repetitive inspections every 500 landings begin at 4,000 landings (see paragraph (f)(1) of this AD.). (ii) The life limit for the inboard forward flap bellcranks (P/N 2622311-7 or FAA-approved equivalent P/N) is 40,000 landings. No repetitive inspections are required on these bellcranks..

Note 1: Inboard forward flap bellcranks (P/N 2622281-2, 2622281-12, or 2692001-2) with 7,000 landings or more do not have to be replaced until 75 landings after December 31, 2002 (the effective date of AD 2002-22-17), unless found cracked.

Note 2: The compliance times of this AD are presented in landings instead of hours TIS. If the number of landings is unknown, hours TIS may be used by multiplying the number of hours TIS by 1.25.

What Are the Actions I Must Do if I Choose the Flap Prohibition Option?

What Are the Actions I Must Do if I Choose the Flap Prohibition Option?

(g) Insert Temporary Revision, 208PHTR02, dated September 23, 2003, into the applicable pilot's operating handbook and FAA-approved airplane flight manual. The owner/operator holding at least a private pilot certificate as authorized by section 43.7 of the Federal Aviation Regulations (14 CFR 43.7) may incorporate this information into the AFM. Make an entry into the aircraft records showing compliance with this portion of the AD in accordance with section 43.9 of the Federal Aviation Regulations (14 CFR 43.9).

(1) This procedure applies to Cessna Models 208 and 208B landplanes. For other FAA-approved aircraft configurations (for example, amphibian, floatplanes, and so forth), you must operate with flaps up per the appropriate airplane flight manual supplement.

(2) This procedure allows for applicable deviation from the Master Minimum Equipment List (MMEL) for these airplanes until the flap bell crank is replaced. The applicable MMEL requirements go back into effect at the time of flap bell crank replacement.

May I Request an Alternative Method of Compliance?

May I Request an Alternative Method of Compliance?

(h) You may request a different method of compliance or a different compliance time for this AD by following the procedures in 14 CFR 39.19. Unless FAA authorizes otherwise, send your request to your principal inspector. The principal inspector may add comments and will send your request to the Manager, Wichita Aircraft Certification Office (ACO), FAA.

(1) For information on any already approved alternative methods of compliance, contact Paul Nguyen, Aerospace Engineer, FAA, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4125; facsimile: 816-946-4107.

(2) Alternative methods of compliance approved under AD 2002-22-17 and AD 2003-21-04 are not approved for this AD.

Does This AD Incorporate Any Material by Reference?

Does This AD Incorporate Any Material by Reference?

(i) You must do the actions required by this AD following the instructions in the service information presented in paragraphs (i)(1) and (i)(2) of this AD.

(1) On December 31, 2002 (67 FR 68508, November 12, 2002) and in accordance with 5 U.S.C. 552(a) and 1 CFR part 51, the Director of the Federal Register approved the incorporation of Cessna Service Bulletin No.: CAB02-1, dated February 11, 2002.

(2) On October 21, 2003 (68 FR 59707, October 17, 2003), and in accordance with 5 U.S.C. 552(a) and 1 CFR part 51, the Director of the Federal Register approved the incorporation of Cessna Caravan Service Bulletin No.: CAB03-11, Revision 1, dated September 24, 2003; Cessna Caravan Service Bulletin No. CAB02-12, revision 1, dated January 27, 2003; and Cessna Caravan Service Kit No.: SK208-148A, dated January 27, 2003 (original issue: October 21, 2002).

(3) You may get a copy from Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67277; telephone: (316) 517-5800; facsimile: (316) 942-9006. You may review copies at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code--of--federal --regulations/ ibr--locations.html.

Issued in Kansas City, Missouri, on August 5, 2004. Dorenda D. Baker, Manager, Small Airplane Directorate, Aircraft Certification Service.