AD 2003-09-13 the New Piper Aircraft, Inc. Models PA-23, PA-23-160, PA-23-235, PA-23-250, and PA-E23-250 Airplanes
This amendment adopts a new airworthiness directive (AD) that applies to certain The New Piper Aircraft, Inc. (Piper) Models PA-23, PA-23-160, PA-23-235, PA-23-250, and PA-E23-250 airplanes that do not incorporate a certain design flap control torque tube or torque tube assembly. This AD requires you to repetitively inspect the flap control torque tube for cracks, corrosion, wear, or elongation of the attachment bolt holes (referred to as damage); and requires you to replace any damaged torque tube with either an improved design flap control torque tube or flap control torque tube assembly. The repetitive inspections will no longer be necessary when the improved design torque tube or torque tube assembly is installed. This AD is the result of several reports of damage found in the flap control torque tube on the affected airplanes. The actions specified by this AD are intended to detect and correct damage to the flap control torque tube, which could result in failure of the flap operating system. If such failure occurred during landing or takeoff, then a split flap condition could occur with potential loss of control of the airplane.
[Docket No. 2002-CE-44-AD; Amendment 39-13142; AD 2003-09-13] RIN 2120-AA64
Airworthiness Directives; the New Piper Aircraft, Inc. Models PA-23, PA-23-160, PA-23-235, PA-23-250, and PA-E23-250 Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
Summary
SUMMARY: This amendment adopts a new airworthiness directive (AD) that applies to certain The New Piper Aircraft, Inc. (Piper) Models PA-23, PA-23-160, PA-23-235, PA-23-250, and PA-E23-250 airplanes that do not incorporate a certain design flap control torque tube or torque tube assembly. This AD requires you to repetitively inspect the flap control torque tube for cracks, corrosion, wear, or elongation of the attachment bolt holes (referred to as damage); and requires you to replace any damaged torque tube with either an improved design flap control torque tube or flap control torque tube assembly. The repetitive inspections will no longer be necessary when the improved design torque tube or torque tube assembly is installed. This AD is the result of several reports of damage found in the flap control torque tube on the affected airplanes. The actions specified by this AD are intended to detect and correct damage to the flap control torque tube, which could result in failure of the flap operating system. If such failure occurred during landing or takeoff, then a split flap condition could occur with potential loss of control of the airplane.
Dates
DATES: This AD becomes effective on June 23, 2003.
The Director of the Federal Register approved the incorporation by reference of certain publications listed in the regulations as of June 23, 2003.
ADDRESSES: You may get the service information referenced in this AD from The New Piper Aircraft, Inc., Customer Services, 2926 Piper Drive, Vero Beach, Florida 32960; telephone: (561) 567-4361; facsimile: (772) 978-6573. You may view this information at the Federal Aviation Administration (FAA), Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2002-CE-44-AD, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.
For Further Information Contact
FOR FURTHER INFORMATION CONTACT: Hassan Amini, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office, One Crown Center, 1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia 30349; telephone: (770) 703-6080; facsimile: (770) 703-6097.
SUPPLEMENTARY INFORMATION:
Discussion
What Events Have Caused This AD?
What Events Have Caused This AD?
A review of FAA's service difficulty report (SDR) database shows several incidents of cracks and corrosion in the flap control torque tube on Piper PA-23 series airplanes. One incident of a broken flap control torque tube resulted in a split flap condition during approach.
What Is the Potential Impact if FAA Took No Action?
What Is the Potential Impact if FAA Took No Action?
Cracked or corroded flap torque tubes, if not detected and corrected, could result in damage to the flap control torque tube and failure of the flap operating system. If such failure occurred during landing or takeoff, then a split flap condition could occur with potential loss of control of the airplane.
Has FAA Taken Any Action to This Point?
Has FAA Taken Any Action to This Point?
We issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain Piper Models PA-23, PA-23-160, PA-23-235, PA-23-250, and PA-E23-250 airplanes that do not incorporate a certain design flap control torque tube or torque tube assembly. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on January 27, 2003. The NPRM proposed to require you to repetitively inspect the flap control torque tube for cracks, corrosion, wear, or elongation of the attachment bolt holes; and would require you to replace any damaged flap control torque tube with either an improved design flap control torque tube or flap control torque tube assembly. The repetitive inspections would no longer be necessary when the improved design flap control torque tube or flap control torque tube assembly is installed.
Was the Public Invited To Comment?
Was the Public Invited To Comment?
The FAA encouraged interested persons to participate in the making of this amendment. We did not receive any comments on the proposed rule or on our determination of the cost to the public.
FAA's Determination
What Is FAA's Final Determination on This Issue?
What Is FAA's Final Determination on This Issue?
After careful review of all available information related to the subject presented above, we have determined that air safety and the public interest require the adoption of the rule as proposed except for minor editorial corrections. We have determined that these minor corrections:
--Provide the intent that was proposed in the NPRM for correcting the unsafe condition; and --Do not add any additional burden upon the public than was already proposed in the NPRM.
How Does the Revision to 14 CFR Part 39 Affect This AD?
How Does the Revision to 14 CFR Part 39 Affect This AD?
On July 10, 2002, FAA published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs FAA's AD system. This regulation now includes material that relates to special flight permits, alternative methods of compliance, and altered products. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.
Cost Impact
Cost Impact
How Many Airplanes Does This AD Impact?
We estimate that this AD affects 3,733 airplanes in the U.S. registry.
What Is the Cost Impact of This AD on Owners/Operators of the Affected Airplanes?
We estimate the following costs to accomplish the inspection:
Total cost on U.S.
What Is the Cost Impact of This AD on Owners/Operators of the Affected Airplanes?
Labor cost Parts cost Total cost per airplane operators
8 workhours x $60 per hour = $480.... None for inspection.... $480 per airplane … $1,791,840.
We estimate the following costs to accomplish any necessary replacement that will be required based on the results of the inspection. We have no way of determing the number of airplanes that may need such repair/replacement:
Total cost per
Labor cost Parts cost airplane
4 workhours x $60 per hour = $452 per airplane. $692 per airplane.
$240.
Regulatory Impact
Regulatory Impact
Does This AD Impact Various Entities?
The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.
Does This AD Involve a Significant Rule or Regulatory Action?
Does This AD Involve a Significant Rule or Regulatory Action?
For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the final evaluation prepared for this action is contained in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. FAA amends § 39.13 by adding a new AD to read as follows:
2003-09-13 The New Piper Aircraft, Inc.: Amendment 39-13142; Docket No. 2002-CE-44-AD.
§ 39.13 [Amended]
(a) What airplanes are affected by this AD? This AD affects the following airplane models and serial numbers that are certificated in any category and do not incorporate a part number (P/N) 17634-002 flap control torque tube; or a P/N 104622-002 or 104622-004 flap control torque tube assembly:
Model Serial numbers
PA-23 and PA-23-160 23-1 through 23-2046.
PA-23-235 27-505 through 27-622.
PA-23-250 27-1 through 27-504 and 27-2000
through 27-8154030.
PA-E23-250 27-2505 through 27-4916 and 27-
7304917 through 27-7554168.
(b) Who must comply with this AD? Anyone who wishes to operate any of the airplanes identified in paragraph (a) of this AD must comply with this AD.
(c) What problem does this AD address? The actions specified by this AD are intended to detect and correct damage to the flap control torque tube, which could result in failure of the flap operating system. If such failure occurred during landing or takeoff, then a split flap condition could occur with potential loss of control of the airplane.
(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:
Actions Compliance Procedures
(1) Inspect the flap control Initially inspect In accordance with
torque tube for cracks, upon accumulating sections 3 through
corrosion, wear, or 2,500 hours time-in- 10 of the
elongation of the service (TIS) on ACCOMPLISHMENT
attachment bolt holes the flap control INSTRUCTIONS
(referred to as damage). torque tube or section of Piper
within the next 100 Mandatory Service
hours TIS after Bulletin No. 1051B,
June 23, 2003 (the dated November 5,
effective date of 2002.
this AD), whichever
occurs later.
Repetitively
inspect thereafter
at intervals not to
exceed 500 hours
TIS until a
replacement flap
control torque tube
or flap control
torque tube
assembly specified
in paragraph (d)(2)
of this AD is
installed.
(2) Replace any damaged flap Prior to further In accordance with
control torque tube and flight after the sections 3 through
replace any wooden end inspection where 10 of the
plugs with new plastic end damage is found. ACCOMPLISHMENT
plugs, P/N 17631-002. INSTRUCTIONS
Replace the flap control section of Piper
torque tubes with either a Mandatory Service
P/N 17634-002 flap control Bulletin No. 1051B,
torque tube or a P/N 104622- dated November 5,
002 or 104622-004 flap 2002.
control torque tube assembly. (i) The P/N 17631-002 end plugs are part of the P/N 104622-002 and 104622-004 flap control torque tube assemblies, but must be obtained for the P/N 17634-002 installation. (ii) You do not have to inspect the existing wooden end plugs as specified in the service bulletin since this AD requires the installation of plastic end plugs.
(3) The repetitive You may replace the In accordance with
inspections required by flap control torque sections 3 through
this AD may be terminated tube assembly at 10 of the
after installation of a any time, but must ACCOMPLISHMENT
replacement flap control replace prior to INSTRUCTIONS
torque tube or flap control further flight if section of Piper
torque tube assembly as damage is found Mandatory Service
specified in paragraph during an Bulletin No. 1051B,
(d)(2) of this AD. inspection. dated November 5,
2002.
(e) Can I comply with this AD in any other way? To use an alternative method of compliance or adjust the compliance time, use the procedures in 14 CFR 39.19. Send these requests to the Manager, Atlanta Aircraft Certification Office. For information on any already approved alternative methods of compliance, contact Hassan Amini, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office, One Crown Center, 1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia 30349; telephone: (770) 703-6080; facsimile: (770) 703-6097.
(f) Are any service bulletins incorporated into this AD by reference? Actions required by this AD must be done in accordance with Piper Mandatory Service Bulletin No. 1051B, dated November 5, 2002. The Director of the Federal Register approved this incorporation by reference under 5 U.S.C. 552(a) and 1 CFR part 51. You may get copies from The New Piper Aircraft, Inc., Customer Services, 2926 Piper Drive, Vero Beach, Florida 32960; telephone: (561) 567-4361; facsimile: (772) 978-6573. You may view copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri, or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.
(g) When does this amendment become effective? This amendment becomes effective on June 23, 2003.
Issued in Kansas City, Missouri, on April 30, 2003. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.