Radar Vectors
Airworthiness Directive Historical Issued Jan 12, 2000 4 pages Copy saved Nov 17, 2026

AD 2000-01-09 GE Aircraft Engines CJ610 Series Turbojet Engines and CF700 Turbofan Engines

This amendment adopts a new airworthiness directive (AD) that is applicable to GE Aircraft Engines (GEAE) CJ610 series turbojet and CF700 series turbofan engines. This action requires removal of certain unapproved parts before further flight. This amendment is prompted by findings that life-limited parts, with forged and inaccurate records, have been introduced into the field and might be installed on the affected engines. The actions specified in this AD are intended to prevent the use of unapproved parts. This condition, if not corrected, could lead to an uncontained engine failure and damage to the airplane.

This document is historical. Superseded by AD 2001-10-12. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 99-NE-58-AD; Amendment 39-11506; AD 2000-01-09] RIN 2120-AA64

Airworthiness Directives; GE Aircraft Engines CJ610 Series Turbojet Engines and CF700 Turbofan Engines

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

Summary

SUMMARY: This amendment adopts a new airworthiness directive (AD) that is applicable to GE Aircraft Engines (GEAE) CJ610 series turbojet and CF700 series turbofan engines. This action requires removal of certain unapproved parts before further flight. This amendment is prompted by findings that life-limited parts, with forged and inaccurate records, have been introduced into the field and might be installed on the affected engines. The actions specified in this AD are intended to prevent the use of unapproved parts. This condition, if not corrected, could lead to an uncontained engine failure and damage to the airplane.

Dates

DATES: Effective February 11, 2000.

Comments for inclusion in the Rules Docket must be received on or before March 13, 2000.

ADDRESSES: Submit comments in triplicate to the Federal Aviation Administration (FAA), New England Region, Office of the Regional Counsel, Attention: Rules Docket No.99-NE-58-AD, 12 New England Executive Park, Burlington, MA 01803-5299. Comments may also be sent via the Internet using the following address: "[email protected]." Comments sent via the Internet must contain the docket number in the subject line.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Kevin Donovan, Aerospace Engineer, Engine Certification Office, FAA, Engine and Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803-5299; telephone (781) 238-7743, fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: On or about October 20, 1999, an investigation jointly conducted by the Department of Transportation Inspector General and the Federal Bureau of Investigation concluded that the airworthiness documentation accompanying certain parts distributed contained false and inaccurate data. Some airworthiness approvals appear to contain signature blocks that were electronically scanned from a signature block obtained from a previous airworthiness approval form. The scanned signature block was then electronically applied to other airworthiness approval forms, which contained fictitious cycle counts. In addition, documents appear to have been created by splicing together several items then photocopying the created document to make the copy appear as an original document. Thus, the airworthiness of those parts is suspect. The FAA has identified 127 rotating parts, identified in Appendix 1 by part number and serial number, that are determined to be unapproved parts. Continued operation of these unapproved parts may result in life limited parts exceeding the FAA approved low-cycle fatigue life limits. This condition, if not corrected, could lead to an uncontained engine failure and damage to the airplane.

Required Actions

Required Actions

Since an unsafe condition has been identified that is likely to exist or develop on other GE CJ610 series turbojet and CF700 series turbofan engines of the same type design, this AD is being issued to prevent use of unapproved parts, which could lead to an uncontained engine failure. This AD requires removal of parts listed in Appendix 1 of this AD before further flight and replacement with serviceable parts.

Immediate Adoption

Immediate Adoption

Since a situation exists that requires the immediate adoption of this regulation, it is found that notice and opportunity for prior public comment hereon are impracticable, and that good cause exists for making this amendment effective in less than 30 days.

Comments Invited

Comments Invited

Although this action is in the form of a final rule that involves requirements affecting flight safety and, thus, was not preceded by notice and an opportunity for public comment, comments are invited on this rule. Interested persons are invited to comment on this rule by submitting such written data, views, or arguments as they may desire. Communications should identify the Rules Docket number and be submitted in triplicate to the address specified under the caption ADDRESSES. All communications received on or before the closing date for comments will be considered, and this rule may be amended in light of the comments received. Factual information that supports the commenter's ideas and suggestions is extremely helpful in evaluating the effectiveness of the AD action and determining whether additional rulemaking action would be needed.

Comments are specifically invited on the overall regulatory, economic, environmental, and energy aspects of the rule that might suggest a need to modify the rule. All comments submitted will be available, both before and after the closing date for comments, in the Rules Docket for examination by interested persons. A report that summarizes each FAA-public contact concerned with the substance of this AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments submitted in response to this notice must submit a self-addressed, stamped postcard on which the following statement is made: "Comments to Docket Number 99-NE-58-AD." The postcard will be date stamped and returned to the commenter.

Regulatory Impact

Regulatory Impact

This final rule does not have federalism implications, as defined in Executive Order 13132, because it does not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Accordingly, the FAA has not consulted with state authorities prior to publication of this final rule.

The FAA has determined that this regulation is an emergency regulation that must be issued immediately to correct an unsafe condition in aircraft, and is not a "significant regulatory action" under Executive Order 12866. It has been determined further that this action involves an emergency regulation under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979). If it is determined that this emergency regulation otherwise would be significant under DOT Regulatory Policies and Procedures, a final regulatory evaluation will be prepared and placed in the Rules Docket. A copy of it, if filed, may be obtained from the Rules Docket at the location provided under the caption ADDRESSES.'

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. Section 39.13 is amended by adding the following new airworthiness directive:

2000-01-09 General Electric Aircraft Engines (GEAE): Amendment 39-11506. Docket 99-NE-58-AD.

§ 39.13 [Amended]

Applicability: CJ610 series turbojet and CF700 series turbofan engines, with parts listed by part number (P/N) and serial number (SN) in Appendix 1, installed. These engines are installed on, but not limited to, the Dassault-Aviation Fan Jet Falcon 20 series, Sabreliner NA265 series, Learjet 20 series, Israel Aircraft Industries Westwind series, Hansa Jet, Aero Commander, and Jet Commander.

Appendix 1

Appendix 1

Part number Part name Serial number

3007T98G01 … Shaft, compressor drive … HPCTQA11693

3007T98G01 … Shaft, compressor drive … HPCTQA11929

3007T98G01 … Shaft, compressor drive … HPCTQA1929

3007T98G01 … Shaft, compressor drive … HPGTQA9947

3007T98G01 … Shaft, compressor drive … TQA14300

37D401014P101 … Torque ring, turbine … GGM681

37D401014P101 … Torque ring, turbine … GGMCBK1977

37D401014P101 … Torque ring, turbine … GGMWZA1230

37D401014P101 … Torque ring, turbine … GGMWZA2322

37D401014P101 … Torque ring, turbine … GGMWZA4665

37D401014P101 … Torque ring, turbine … PMB08403P

37D401014P102 … Torque ring, turbine … PMB19204

37D401302P101 … Spacer, stage 2 … GATI2099WYR

37D401302P101 … Spacer, stage 2 … GATWZA09656

37D401302P101 … Spacer, stage 2 … GATWZA10002

37D401302P101 … Spacer, stage 2 … GATWZA10148

37D401302P101 … Spacer, stage 2 … GATWZA5419

37D401303P102 … Spacer, stage 3 … GATCBK02192

37D401303P102 … Spacer, stage 3 … GATWZA12030

37D401303P102 … Spacer, stage 3 … GGMWZA1022

37D401303P104 … Spacer, stage 3 … GATWYR5364

37D401304P104 … Spacer, stage 4 … GATANWA2378

37D401305P103 … Spacer, stage 5 …

GATANW9528

37D401305P103 … Spacer, stage 5 … GATANWA7441

37D401305P103 … Spacer, stage 5 … GATANWA8542

37D401305P103 … Spacer, stage 5 … GGMANW3172

37D401306P103 … Spacer, stage 6 … GATANW6380

37D401306P103 … Spacer, stage 6 … GGMANW2331

37D401306P105 … Spacer, stage 6 … GATCDY71386

37D401306P105 … Spacer, stage 6 … GATO7040CDY

37D401307P103 … Spacer, stage 7 … GAT59653

37D401307P103 … Spacer, stage 7 … GATANW7170

37D401307P103 … Spacer, stage 7 … GATANWA7134

37D401307P103 … Spacer, stage 7 … GGMANW3104

37D401312P101 … Disc, stage 2 … GATI0156WZA

37D401312P101 … Disc, stage 2 … GATO8253WZA

37D401312P101 … Disc, stage 2 … GATWZA3983

37D401312P101 … Disc, stage 2 … GATWZA6604

37D401312P101 … Disc, stage 2 … GGMCBK620

37D401312P101 … Disc, stage 2 … GGMLBA4491

37D401313P101 … Disc, stage 3 … GATI3249WYI

37D401313P101 … Disc, stage 3 … GATO7644WZA

37D401313P101 … Disc, stage 3 … GATWZA6522

37D401313P101 … Disc, stage 3 … GATWZA6723

37D401313P101 … Disc, stage 3 … GGMLBA2102

37D401314P102 … Disc, stage 4 … GAT05572WZA

37D401314P102 … Disc, stage 4 … GATO4383WZA

37D401314P102 … Disc,

stage 4 … GGMWZA6818

37D401315P101 … Disc, stage 5 … GAT12406WZA

37D401315P101 … Disc, stage 5 … GATWZA4753

37D401315P101 … Disc, stage 5 … GATWZA7093

37D401316P101 … Disc, stage 6 … GAT10162WZA

37D401316P101 … Disc, stage 6 … GATWZA4435

37D401316P101 … Disc, stage 6 … GATWZA7208

37D401316P101 … Disc, stage 6 … GGMWZA3376

37D401317P101 … Disc, stage 7 … GAT10013WZA

37D401317P101 … Disc, stage 7 … GAT13322WZA

37D401317P101 … Disc, stage 7 … GATI5009WYR

37D401709P101 … Disc, stage 8 … GATO3900WZA

37D401709P101 … Disc, stage 8 … GATO5381WZA

37D401709P101 … Disc, stage 8 … GGMWZA6906

37D401709P101 … Disc, stage 8 … GGMWZA6942

37E501428P102 … Disc and shaft, stage 1 … GATI2001WZA

37E501428P102 … Disc and shaft, stage 1 … GATWZA8639

37E501428P106 … Disc and shaft, stage 1 … GATO8474WZA

37E501428P106 … Disc and shaft, stage 1 … GGMWZA3231

4010T01P01 … Seal labyrinth, stage 8 … JADCSF334P59

4010T01P01 … Seal labyrinth, stage 8 … JADCSF5222

4010T01P01 … Seal labyrinth, stage 8 … JADCSF5444P21

4010T01P01 … Seal labyrinth, stage 8 … JADMCI3214

4036T24P01 … Turbine wheel, stage 2 …

GATWYR14035

4036T24P01 … Turbine wheel, stage 2 … GATWYR14655

5013T79P01 … Disc, stage 5 … GATI1679WZA

5013T82P01 … Disc, stage 7 … GATI7662WYR

5013T88P01 … Spacer, stage 4 … GAT69935

5013T88P01 … Spacer, stage 4 … GATCDY66715

5013T89P01 … Spacer, stage 5 … GAT60180CDY

5013T90P01 … Spacer, stage 7 … GAT81678CDY

5013T90P01 … Spacer, stage 7 … GATCDY82036

5018T16P01 … Disc, stage 4 … GAT12222WYR

6028T44P01 … Turbine wheel, stage 1 … GAT11900

6028T44P01 … Turbine wheel, stage 1 … GAT13094

6028T44P01 … Turbine wheel, stage 1 … GAT14749

6028T44P01 … Turbine wheel, stage 1 … GAT15160

6028T44P01 … Turbine wheel, stage 1 … GAT15396WYR

6028T44P01 … Turbine wheel, stage 1 … GAT15703

6028T44P01 … Turbine wheel, stage 1 … GAT15821

6028T44P01 … Turbine wheel, stage 1 … GAT15899

6028T44P01 … Turbine wheel, stage 1 … GAT59743

6028T44P01 … Turbine wheel, stage 1 … GAT60190

6028T44P01 … Turbine wheel, stage 1 … GAT60197

6028T44P01 … Turbine wheel, stage 1 … GAT60483

6028T44P01 … Turbine wheel, stage 1 … GAT7321

6028T44P01 … Turbine wheel, stage 1 … GATA8475

6028T44P01 … Turbine wheel, stage 1 …

GATA8492

6028T44P01 … Turbine wheel, stage 1 … GATAJ204

6028T44P01 … Turbine wheel, stage 1 … GATB6925

6028T44P01 … Turbine wheel, stage 1 … GATBE998

6028T44P01 … Turbine wheel, stage 1 … GATE2150

6028T44P01 … Turbine wheel, stage 1 … GATE2259

6028T44P01 … Turbine wheel, stage 1 … GATE2291

6028T44P01 … Turbine wheel, stage 1 … GATE2336

6028T44P01 … Turbine wheel, stage 1 … GATF4496

6028T44P01 … Turbine wheel, stage 1 … GATF4507

6028T44P01 … Turbine wheel, stage 1 … GATFE953

6028T44P01 … Turbine wheel, stage 1 … GATG6470

6028T44P01 … Turbine wheel, stage 1 … GATV6541

6028T44P01 … Turbine wheel, stage 1 … GATV6588

6028T44P01 … Turbine wheel, stage 1 … GATW1573

634E583P04 … Turbine wheel, stage 1 … GATWZA4994

634E583P5 … Turbine wheel, stage 1 … GAT10650

634E583P5 … Turbine wheel, stage 1 … GAT13048

646C596P2 … Turbine wheel, stage 2 … GATCBK01912

646C596P2 … Turbine wheel, stage 2 … GATWYR12725

646C596P2 * … Turbine wheel, stage 2 … GATWZA9723

646C594P2 * … Turbine wheel, stage 2 … GATWZA9723

646C594P1 * … Turbine wheel, stage 2 … GATWZA9723

841B690P7 … Assy, Turbine wheel, stage 1...

GAT9383WZA

841B690P7 … Assy, Turbine wheel, stage 1... GATMKF07225

841B690P7 … Assy, Turbine wheel, stage 1... GATWYR12358

841B690P7 … Assy, Turbine wheel, stage 1... GATWYR13457

841B690P7 … Assy, Turbine wheel, stage 1... GATWYR13677

841B690P7 … Assy, Turbine wheel, stage 1... GATWZA8110

841B690P7 … Assy, Turbine wheel, stage 1... GATWZA8263

841B690P7 … Assy, Turbine wheel, stage 1... GATWZA9182

841B690P7 … Assy, Turbine wheel, stage 1... OJL0145

841B690P7 … Assy, Turbine wheel, stage 1... WDBMKF07219

* The FAA has determined that up to three Stage 2 Turbine wheels, SN GATWZA9723, may have been distributed with

* The FAA has determined that up to three Stage 2 Turbine wheels, SN GATWZA9723, may have been distributed with

three different P/N's. Therefore, while only P/N 646C596P1 is an approved P/N for the CJ610 and CF700 model

engine, all three part numbers are listed.

Note 1: This airworthiness directive (AD) applies to each engine identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For engines that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent the use of unapproved parts, which could lead to an uncontained engine failure and damage to the airplane, accomplish the following:

Replacement of Unapproved Parts

(a) Before further flight after the effective date of this AD, remove any part listed by P/N and SN in Appendix 1 of this AD, and replace it with a serviceable part.

Alternate Methods of Compliance

Alternate Methods of Compliance

(b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Engine Certification Office (ECO). Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, ECO.

Note 2: Information concerning the existence of approved alternative methods of compliance with this airworthiness directive, if any, may be obtained from the ECO.

Effective Date of This AD

Effective Date of This AD

(c) This amendment becomes effective on February 11, 2000.

Issued in Burlington, Massachusetts, on January 5, 2000. Jay J. Pardee, Manager, Engine and Propeller Directorate, Aircraft Certification Service.