AC 91-85A Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace
This advisory circular (AC) applies to all Operators conducting Reduced Vertical Separation Minimum (RVSM) operations. The AC can be used to obtain an initial operational authorization, or amend an existing, operational authorization. The AC appendices include supportive information relating to RVSM airworthiness certifications, training programs, operating practices and procedures, RVSM operations in oceanic and remote continental airspace, and review of height-keeping parameters. This AC describes acceptable means, but not the only means, for an Operator to obtain authorization to conduct flight in airspace or on routes where RVSM is applied. The advisory material contained in this AC has been substantially modified since the AC was issued in its original form in 2009.
This document is cancelled. It may have been replaced. Check the official source before relying on it.
Deputy Director, Flight Standards Service
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Authorization of Aircraft and
Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace
Date: 7/21/16 Initiated by: AFS-400
AC No: 91-85A Change:
This advisory circular (AC) applies to all Operators conducting Reduced Vertical Separation Minimum (RVSM) operations. The AC can be used to obtain an initial operational authorization, or amend an existing, operational authorization. The AC appendices include supportive information relating to RVSM airworthiness certifications, training programs, operating practices and procedures, RVSM operations in oceanic and remote continental airspace, and review of height-keeping parameters.
This AC describes acceptable means, but not the only means, for an Operator to obtain authorization to conduct flight in airspace or on routes where RVSM is applied. The advisory material contained in this AC has been substantially modified since the AC was issued in its original form in 2009.
John Barbagallo Deputy Director, Flight Standards Service
4.2 What are the Applicable Steps and Information Required to Seek an…
iii
CONTENTS Paragraph Page
Chapter 1. Introduction … 1-1
1.1 What is the Purpose of This Advisory Circular (AC)? … 1-1
1.2 Who Does This AC Apply To? … 1-1
1.3 What Does This AC Cancel? … 1-1
1.4 What Regulations Apply to RVSM Operations? … 1-1
1.5 What Other Reading Material is Helpful to an Applicant? … 1-1
1.6 What Do Some of the Capitalized Terms Used in This AC Mean? … 1-2
Chapter 2. Authorization Overview … 2-1
2.1 Why are RVSM Authorizations Required, and How has the Authorization Process Changed Since RVSM Authorizations were Initially Implemented on a World-Wide Basis? … 2-1
2.2 What are the Basic Technical Requirements Associated with Obtaining an Appropriate RVSM Authorization? … 2-2
2.3 What are the RVSM Authorization Elements? … 2-2
2.4 What is the RVSM Authorization Matrix? … 2-2
2.5 What is a Summary of the Process Needed to Obtain a New RVSM Authorization? … 2-4
Chapter 3. RVSM Authorization Elements … 3-1
3.1 What is the Background Behind Using the RVSM Authorization Elements to Apply for an RVSM Authorization? … 3-1
3.2 What Do I Need to Know About RVSM-Compliant Aircraft? … 3-1
3.3 What Do I Need to Know About RVSM-Knowledgeable Pilots? … 3-2
3.4 Who is the Proper Party to be the Applicant for, and the Operator Under, an RVSM Authorization? … 3-3
3.5 Who is a “Responsible Person,” and What Duties Does This Person Fulfill, Under an RVSM Authorization? … 3-4
3.6 What Other Issues Should be Addressed by Applicants with Respect to Requests for RVSM Authorizations? … 3-5
Chapter 4. Submitting an Application for RVSM Authorization … 4-1
4.1 What is the First Step an Applicant May Consider Taking When Applying for an RVSM Authorization? … 4-1
4.2 What are the Applicable Steps and Information Required to Seek an RVSM Authorization? … 4-1
Figure C.1-5. Expanded Scenario 3 … C-5
iv
Chapter 5. FAA Review and Evaluation of RVSM Applications … 5-1
5.1 What is the General Process the FAA will Follow Upon Submission of the Request for an RVSM Authorization or Amended Authorization? … 5-1
5.2 What are the Applicable Forms of the RVSM Authorization Documents? … 5-1
5.3 What are the Conditions That Would Require the Removal of an RVSM Authorization? … 5-2
5.4 What Happens if I Change RVSM Equipment After Operational Authorization has been Granted? … 5-3
Appendix A. RVSM Airworthiness Certification … A-1
Appendix B. Training Programs and Operating Practices and Procedures … B-1
Appendix C. Operations in Oceanic and Remote Continental Airspace … C-1
Appendix D. Review of ICAO Document 9574 … D-1
Appendix E. RVSM Authorization Overview … E-1
List of Figures
Figure 4-1. RVSM Decision Matrix … 4-3
Figure A.6-1. Example of Air Data System/Autopilot Configuration … A-13
Figure A.6-2. Single Air Data Computer Configuration for Autopilot Input … A-14
Figure A.8-1. Altimetry System Error and Its Components … A-18
Figure A.8-4. Static Source Error/Static Source Error Correction Relationships for
Altimetry System Error Where Static Line, Pressure Measurement, and Conversion Errors are Zero … A-22
Figure A.9-1. Process for Showing Initial and Continued Compliance of Airframe Static
Pressure System … A-27
Figure A.9-2. Compliance Demonstration Ground-To-Flight Test Correlation Process
Example … A-27
Figure A.9-3. Process for Showing Initial and Continued Compliance of Airframe Static
Pressure Systems for In-Service and New Model Aircraft … A-28
Figure C.1-1. Scenario 1 … C-2
Figure C.1-2. Scenario 2 … C-3
Figure C.1-3. Expanded Scenario 1 … C-4
Figure C.1-4. Expanded Scenario 2 … C-5
Figure C.1-5. Expanded Scenario 3 … C-5
Table A.8-3. Residual Static Source Error (Aircraft with Avionic Static…
v
Figure C.1-6. Expanded Scenario 4 … C-6
Figure C.1-7. Expanded Scenario 5 … C-6
List of Tables
Table A.2-1. Full RVSM Envelope Boundaries … A-5
Table A.8-2. Static Source Error … A-20
Table A.8-3. Residual Static Source Error (Aircraft with Avionic Static Source Error Correction) … A-21
• International Civil Aviation Organization (ICAO) Document 4444,… › • International Civil Aviation Organization (ICAO) Document 4444,…
CHAPTER 1. INTRODUCTION
1.1 What is the Purpose of This Advisory Circular (AC)? This AC is not mandatory and does not constitute a regulation. This AC describes an acceptable means, but not the only means, for an Operator to obtain an initial operational authorization, or amend an existing operational authorization to conduct flight in airspace or on routes where Reduced Vertical Separation Minimum (RVSM) is applied. Additionally, this AC provides information on RVSM performance specifications, obtaining and maintaining RVSM airworthiness certification for aircraft, specific elements of an RVSM authorization, and policy and procedures for RVSM operations. RVSM airspace is any airspace or route between flight level (FL) 290 and FL 410 inclusive where aircraft are separated vertically by 1,000 ft (300 m).
1.2 Who Does This AC Apply To? This AC applies to operators who want to apply for authorization to conduct operations in RVSM airspace.
1.3 What Does This AC Cancel? This AC cancels AC 91-85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum Airspace, dated August 21, 2009, which provided guidance on aircraft and Operator approval for operating in RVSM airspace.
1.4 What Regulations Apply to RVSM Operations? Title 14 of the Code of Federal Regulations (14 CFR):
• Part 43;
• Part 91, §§ 91.180, 91.411, 91.413, 91.705, 91.706, and Appendix G;
• Part 121;
• Part 125;
• Part 129;
• Part 135; and
• Part 145.
1.5 What Other Reading Material is Helpful to an Applicant?
• Federal Aviation Administration (FAA) Aeronautical Information Manual (AIM).
• FAA Order 8900.1, Flight Standards Information Management System (FSIMS) (http://fsims.faa.gov).
• FAA Documentation Web site: http://www.faa.gov/air_traffic/separation_standards/rvsm/documentation/.
• International Civil Aviation Organization (ICAO) Document 4444, Procedures for Air Navigation Services, Air Traffic Management.
• RVSM-Responsible Person. › • RVSM-Responsible Person.
• ICAO Annex 6, Operation of Aircraft, Part I—International Commercial Air Transport—Aeroplanes and Part II—International General Aviation—Aeroplanes.
• ICAO Document 7030, Regional Supplementary Procedures.
• ICAO Document 9574, Manual on Implementation of a 300 m (1000 ft) Vertical Separation Minimum Between FL 290 and FL 410 Inclusive.
1.6 What Do Some of the Capitalized Terms Used in This AC Mean? For the purposes of efficiency and consistency, when the various capitalized terms below are used in this AC, then they have the following meanings. Or you can find their meanings in the paragraphs specifically mentioned in the definition.
• Operator. The person who should be the RVSM authorization applicant and holder. See paragraph 3.4 for a detailed discussion on who is and is not the correct person to be designated as an Operator for the purposes of holding an RVSM authorization.
• RVSM-Authorization Element(s). Individually or together, RVSM-Compliant Aircraft or RVSM-Knowledgeable Pilots. (See paragraph 2.3.)
• RVSM-Compliant Aircraft. An aircraft the FAA has found to comply with the requirements of part 91 appendix G, section 2, for the purposes of conducting RVSM operations. (See paragraph 3.2.)
• RVSM-Knowledgeable Pilots. Pilots who have been trained according to RVSM operating policies and/or procedures for pilots (and, if applicable, dispatchers) the FAA has found are sufficient to ensure each pilot has adequate knowledge of RVSM requirements, policies, and procedures. (See paragraph 3.3.)
• RVSM-Point of Contact (POC). A person an Operator can designate in addition to the RVSM-Responsible Person to act as a contact person who has actual day-to-day knowledge of the RVSM-Compliant Aircraft operations and RVSM airworthiness status the FAA may contact to gather such information when such a need arises. (See paragraph 3.5.)
• RVSM-Responsible Person. A person(s) designated by the Operator who has the legal authority to sign the RVSM authorization on behalf of the Operator and who has adequate knowledge of RVSM requirements, policies, and procedures. (See paragraph 3.5.)
2.1.5 AC Not Regulatory.
CHAPTER 2. AUTHORIZATION OVERVIEW
2.1 Why are RVSM Authorizations Required, and How has the Authorization Process Changed Since RVSM Authorizations were Initially Implemented on a World-Wide Basis?
2.1.1 Special Navigation Area of Operation. RVSM airspace is designated a special navigation area of operation. Both the individual Operator and the specific aircraft type or types the Operator intends to use must be authorized by the appropriate FAA offices before the Operator conducts flight operations in RVSM airspace.
2.1.2 RVSM Implementation. The FAA implemented RVSM in all of the airspace in the lower 48 states, Alaska, the San Juan flight information region (FIR), Gulf of Mexico, and Atlantic High Offshore Airspace on January 20, 2005. To safely operate in RVSM airspace, all aircraft needed to be configured and inspected to ensure the applicable RVSM performance requirements were complied with.
2.1.3 Reason for Change. Because the RVSM requirements were new to most Operators when they were first put into place, those aircraft and Operators had to be reviewed by the FAA as a first instance in order to ensure the basic requirements were being met. Since domestic RVSM implementation occurred in 2005, most existing aircraft have since been configured for compliance or have been newly manufactured in compliance with these requirements and have been reviewed at least once by the FAA. Also, most Operators have now developed pilot knowledge and/or training programs previously reviewed at least once by the FAA. Therefore, the initial “one-size-fits-all” authorization approach initially adopted in 2005, which assumed all Operators, aircraft, and pilot training programs had never been reviewed before, is no longer warranted with respect to the processing of new or amended RVSM authorizations.
2.1.4 FAA Order 8900.1 Guidance. In recognition of these changes, the FAA amended those portions of Order 8900.1, Flight Standards Information Management System (FSIMS), addressing the issuance of RVSM authorizations on January 24, 2014, in order to create guidelines improving efficiency in the authorization process. Based on the changes highlighted above, there is recognition of two key elements for a RVSM authorization. The two key elements are an RVSM-Compliant Aircraft and properly trained pilots who have met applicable RVSM-Knowledgeable Pilots requirements. The guidance was created along with a “decision matrix” (see paragraph 2.4) to allow the FAA to more efficiently direct attention to only the RVSM Authorization Elements requiring initial review. The guidance allows the reviewing safety inspector to accept previously reviewed RVSM Authorization Elements without further examination, so long as the appropriate information has been provided to the FAA as part of the application process.
2.1.5 AC Not Regulatory. The material contained in this AC is not regulatory. It provides several methods for an Operator to successfully apply to the FAA for an RVSM authorization with the goal of expediting the review and approval process.
2.2 What are the Basic Technical Requirements Associated with Obtaining an Appropriate RVSM Authorization?
2.4 What is the RVSM Authorization Matrix?
2.2.1 Altimetry System Error (ASE). RVSM compliance proceeds on the basis of FAA certification of the altimetry system design and implementation, which is typically conveyed through type certification (TC) or Supplemental Type Certification (STC). It is generally acknowledged that one aspect of the design is an instrumentation system error budget allowing for a difference between the static pressure sensed and the actual altitude flown. This difference is not seen on the displayed altitude in the flight deck and it is not in the Mode C or Mode S reply from the aircraft transponder. Therefore, it is invisible to the pilot, to air traffic control (ATC), and to the Traffic Alert and Collision Avoidance System (TCAS).
2.2.2 Height Monitoring. Aircraft instructions for continued airworthiness (ICA) are designed to keep the altimetry system error (ASE) to within the limits of the error budget throughout the flight envelope. These limits vary between aircraft types and within a type, from airframe to airframe. Regardless, even with attention to continuing airworthiness, there are factors that can affect the ASE significantly and can go undetected in routine operations. Thus, through continuous sampling, the FAA independently monitors altimetry system performance of airframes in the population of aircraft participating in RVSM operations. This sampling is accomplished through operational monitoring flights using either special equipment brought on board the aircraft or through separate ground-based height monitoring systems. See paragraph 3.6.4.
2.2.3 RVSM Performance. Appendix A gives details regarding the ASE performance demands for safely operating in RVSM airspace.
2.3 What are the RVSM Authorization Elements? The definition and use of the two RVSM Authorization Elements—RVSM-Compliant Aircraft and RVSM-Knowledgeable Pilots—arose from recognizing these are the two basic building blocks needed to meet the technical requirements in order to safely conduct operations in RVSM airspace. These elements provide the basis for developing the RVSM Matrix (see paragraph 2.4). Once the FAA has found an aircraft to be RVSM-compliant, if it is properly maintained and monitoring shows that its performance has not degraded over time, the aircraft remains RVSM-compliant. Under these conditions, it is inefficient for the FAA to have to review the status of that aircraft again (as if it had never been compliant) when a subsequent Operator requires his/her/its own authorization to operate that aircraft in RVSM airspace. By specifically defining these two elements and putting certain safeguards into place (such as compliance statements by subsequent Operators), the FAA could then create the RVSM Authorization Matrix in order to streamline the process of reviewing and issuing new RVSM.
2.4 What is the RVSM Authorization Matrix? The RVSM Authorization Matrix (or simply the “Matrix”) is a tool created to assist Operators and the FAA in determining the typical documentation needed for application and which RVSM Authorization Elements
approval action the applicant is seeking. The full Matrix is provided in Chapter 4, but the following is a summary of how the Matrix works.
2.4.4 What Additional Issues Should an Applicant be Aware of When Using…
2.4.1 When Does Authorization Group I Apply? Authorization Group I applies to applicants seeking an administrative change only to an existing authorization. The following changes are considered to be administrative in nature only when all other existing elements are not changed:
1. Change in the primary business address of an RVSM-Compliant Aircraft and/or RVSM authorization holder.
2. Change in an existing RVSM Operator’s designated Responsible Person (or RVSM-Authorized Representative or RVSM-POC).
3. Change in the registration markings of an RVSM-Compliant Aircraft being operated by an existing RVSM authorization holder.
4. Removal of an RVSM-Compliant Aircraft from an existing RVSM authorization having multiple RVSM-Compliant Aircraft listed.
2.4.2 When Does Authorization Group II Apply? Authorization Group II applies to applicants seeking new RVSM authorizations based on one or more existing approved RVSM Elements. This group will normally apply to a new or proposed RVSM Operator seeking the issuance of an RVSM authorization for an aircraft already an RVSM-Compliant Aircraft or where the new RVSM Operator will be utilizing previously accepted RVSM- Knowledgeable Pilots requirements with respect to its operations of that specific aircraft. Examples given in the Matrix include:
1. There is a change in the legal status or identity of the business entity that is the approved RVSM Operator, but the Responsible Person, RVSM Authorized Representative, and/or RVSM Contact Person and each of the approved RVSM Authorization Elements are remaining the same.
2. A new proposed RVSM Operator will be using an existing RVSM-Compliant Aircraft or previously accepted RVSM-Knowledgeable Pilots.
3. An existing or new proposed approved RVSM Operator seeks an RVSM authorization and will be utilizing one or more existing approved RVSM Authorization Elements.
2.4.3 When Does Authorization Group III Apply? Authorization Group III applies to applicants for new RVSM authorizations not based on any existing RVSM Authorization Elements. If neither Authorization Group I nor II apply, the applicant should submit sufficient evidence to show its ability to comply with each of the RVSM Authorization Elements.
2.4.4 What Additional Issues Should an Applicant be Aware of When Using the Matrix? The FAA has created inspector guidance in order to allow for the most efficient processing of an RVSM authorization without sacrificing operational safety. While a safety inspector may rely on that guidance in issuing new or amended RVSM authorizations, applicants
6. If the applicant determines they are unable to use any existing RVSM… › 6. If the applicant determines they are unable to use any existing RVSM…
should understand each Flight Standards District Office (FSDO), certificate-holding district office (CHDO), International Field Office (IFO), principal operations inspector (POI), principal avionics inspector (PAI), principal maintenance inspector (PMI), and/or aviation safety inspector (ASI) retains the authority to conduct as much review and research with respect to any proposed RVSM-Compliant Aircraft or RVSM- Knowledgeable Pilots requirements as is warranted. This authority is to ensure safety and regulatory compliance requirements have been met. Applicants should also understand it is the Operator's responsibility to ensure documentation reflects the requirements for authorization. A positive statement by the Operator detailing any changes made to previously approved programs can assist the inspector in determining the level of review necessary.
2.5 What is a Summary of the Process Needed to Obtain a New RVSM Authorization? Chapters 3, 4, and 5 of this AC describe the RVSM authorization process in detail, but a summary of this process is as follows:
1. The applicant identifies the appropriate FAA office to apply to. (See paragraph 4.1.2.)
2. The applicant determines if a new RVSM authorization is required, or if only an amendment to an existing RVSM authorization is required. (See paragraph 4.2.1.)
3. If only an amendment to an existing RVSM authorization is required, then the applicant will follow the procedures described in paragraph 4.2.1 with respect to Authorization Group I in the Matrix.
4. If the applicant determines a new RVSM authorization is required, then the applicant should first determine who the correct Operator will be with respect to applying for and holding the RVSM authorization. (See paragraph 3.4.)
5. Once the appropriate Operator is determined, the applicant will determine if it will be utilizing any existing RVSM Authorization Elements, and if so, will then follow the process described in paragraph 4.2.2 with respect to Authorization Group II in the Matrix.
6. If the applicant determines they are unable to use any existing RVSM Authorization Elements, then the applicant will follow the process described in paragraph 4.2.4 with respect to Authorization Group III in the Matrix.
CHAPTER 3. RVSM AUTHORIZATION ELEMENTS
3.1 What is the Background Behind Using the RVSM Authorization Elements to Apply for an RVSM Authorization? The RVSM authorization process recognizes two key elements of any RVSM authorization—an RVSM-Compliant Aircraft and properly trained pilots who have met applicable RVSM-Knowledgeable Pilots requirements. An Operator must demonstrate to the FAA both of these elements exist to be authorized to operate in RVSM airspace. All of these RVSM Authorization Elements are described in this chapter.
3.2.2 How Does an Aircraft Achieve the Designation of Being an…
3.2 What Do I Need to Know About RVSM-Compliant Aircraft?
3.2.1 What is an RVSM-Compliant Aircraft? An aircraft is an “RVSM-Compliant Aircraft” when (1) the FAA has determined the aircraft design satisfies RVSM performance requirements and (2) the aircraft has been properly maintained on an on-going basis to conduct such operations. An aircraft will satisfy RVSM performance requirements if it complies with part 91 appendix G, section 2. (See paragraph 3.2.2 below for more detail concerning meeting these performance requirements.) Aircraft may be produced RVSM-compliant or brought into compliance through the application of appropriate Service Bulletins (SB), Service Letters (SL), Engineering Change Orders (ECO), or STCs.
3.2.1.1 If the aircraft was manufactured RVSM-compliant, the date of the Airworthiness Certificate is usually the compliancy date. (For additional information see the Airplane Flight Manual (AFM), AFM Supplement (AFMS), and/or Type Certificate Data Sheet (TCDS).
3.2.1.2 If the aircraft was made RVSM-compliant through a SB, STC, or SL, or other appropriate methods, the RVSM-compliant date will be listed in the airframe maintenance log. Include copies of the maintenance record return to service entry.
3.2.2 How Does an Aircraft Achieve the Designation of Being an RVSM-Compliant Aircraft? Each aircraft type an Operator intends to use in RVSM airspace should have received FAA RVSM airworthiness approval in accordance with part 91 appendix G, section 2, before the operational authorization will be granted. Obtaining RVSM airworthiness approval is a two-step process. First, the manufacturer or design organization develops a data package through which to seek RVSM airworthiness approval and submits the package to the appropriate FAA Aircraft Certification Office (ACO) for approval. Once the ACO approves the data package, the Operator applies the procedures defined in the package to obtain approval from the FSDO/CHDO/certificate management office (CMO)/IFO (as appropriate) to use its aircraft to conduct flight in RVSM airspace. The initial airworthiness review process must consider continued airworthiness requirements, as described in Appendix A of this document. For more detail on RVSM aircraft airworthiness approvals see Appendix A.
3.3.1.2 For an applicant who operates under part 91 subpart K (part…
3.2.3 How Does an Aircraft Retain the Designation of Being an RVSM-Complaint Aircraft? An aircraft once designated RVSM-compliant should retain that designation as long as properly configured and the maintenance procedures listed in the ICA are complied with. Subsequent modifications to the aircraft must be evaluated and determined to have no negative impact on RVSM design or performance.
3.3 What Do I Need to Know About RVSM-Knowledgeable Pilots?
3.3.1 Who are RVSM-Knowledgeable Pilots? To obtain authorization from the Administrator to conduct operations in RVSM airspace, the Administrator must find the Operator to have adopted RVSM operating policies and/or procedures for pilots (and, if applicable, dispatchers) and ensure each pilot has adequate knowledge of RVSM requirements, policies, and procedures, with those pilots (and, if applicable, dispatchers) being referred to in this AC as “RVSM-Knowledgeable Pilots.”
3.3.1.1 For an applicant operating only under part 91 or part 125 (including A125 Letter of Deviation Authority (LODA) holders), demonstrating it has RVSM-Knowledgeable Pilots will consist of providing sufficient evidence each pilot has an adequate knowledge of RVSM requirements, policies, and procedures as required in part 91 appendix G, section 3(c)(2).
• The following are acceptable means for the Operator to show the FAA its pilots have adequate knowledge of the RVSM operating practices and procedures: 14 CFR part 142 training center certificates without further evaluation; certificates documenting completion of a course of instruction on RVSM policy and procedures; and/or an Operator’s in-house training program.
Note: The FAA, at its discretion, may evaluate a training course prior to accepting a training certificate.
3.3.1.2 For an applicant who operates under part 91 subpart K (part 91K), 121, or 135, in addition to meeting the adequate knowledge requirements for part 91 operators, that applicant will need to provide sufficient evidence of initial and recurring pilot training and/or testing requirements as well as policies and procedures allowing the operator to conduct RVSM operations safely as required in part 91 appendix G, section 3(b)(2) and (3) in order to demonstrate they are using RVSM-Knowledgeable Pilots. Therefore, part 91K, 121, and 135 Operators should submit training syllabi and other appropriate material to the FAA showing operating practices and procedures and training items related to RVSM operations are incorporated in initial and, where warranted, recurrent training programs. (Training for dispatchers should be included, where appropriate.)
2. For non-commercial operations conducted under part 91 and part 125… › 2. For non-commercial operations conducted under part 91 and part 125…
3.3.2 What Additional Operational Policy and Procedure Components Should be Considered with Respect to RVSM-Knowledgeable Pilots?
3.3.2.1 Applicants should consider standardizing practices and procedures in the following areas using the guidelines in Appendix B: flight planning, preflight procedures at the aircraft for each flight, procedures prior to RVSM airspace entry, in-flight procedures, and flightcrew training procedures. Paragraph B.7 contains special emphasis items for flightcrew training. Also, pilots and dispatchers (where applicable) should be knowledgeable on contingency and other procedures unique to an operator’s specific areas of operation. Also, Appendix C contains guidance on operations in oceanic and remote continental airspace.
3.3.2.2 Aircraft approved for RVSM can be used in RVSM operations worldwide. This includes RVSM operation in continental areas such as Europe and the United States. Aircraft equipage and altitude-keeping performance requirements were developed using the highest density traffic counts in the world so aircraft could receive one-time approval for worldwide operations. Operators starting RVSM operations in an RVSM area of operation new to them should ensure their RVSM programs incorporate any operations or continued airworthiness requirements unique to the new area of operations.
3.4 Who is the Proper Party to be the Applicant for, and the Operator Under, an RVSM Authorization?
3.4.1 Who is the Correct Person to Apply for and Have Issued the RVSM Authorization? The person exercising operational control of the aircraft during the operation requiring an RVSM authorization is the proper person to be the applicant for that authorization. It is important to note it is the RVSM applicant’s responsibility to submit a request for RVSM authorization in the name of the person having operational control of the aircraft, not the responsibility of the FSDO or a specific ASI to make such a determination. The following general information may be useful in assisting the RVSM applicant in determining if the appropriate party has been properly designated as the legal Operator with respect to the RVSM authorization request:
1. For commercial and fractional ownership program operations conducted under parts 91K, 121, 125, and 135, the authorization applicant and holder should be the operating certificate holder, air carrier certificate holder, or fractional ownership program manager, in which event the authorization will be issued in the form of an appropriate operations specification (OpSpec) or management specification (MSpec).
2. For non-commercial operations conducted under part 91 and part 125 (A125 LODA holders), the authorization applicant and legal Operator should normally be one of the following persons, in which event the authorization will be issued in the form of an appropriate letter of authorization (LOA):
3.5.1.2 The Operator should also designate a person(s) to act as a…
• A registered owner of the aircraft operating the aircraft incidental to its own non-air transportation business or personal activity.
• A person assuming operational control of the aircraft through a lease or use agreement for that person’s operation of the aircraft incidental to that person’s own non-air transportation business or personal activity.
Note: The legal Operator will generally not be: an owner trustee not operating the aircraft for its own business, a management company that has not accepted a transfer of operational control from the Operator, or a holding company or bank that holds title to the aircraft solely for the purpose of leasing or transferring operational control of the aircraft to other persons.
3. It is both possible and common to have multiple Operators for part 91, 91K, and/or 125/135 aircraft over a short period of time and on a non-exclusive basis (for example, multiple dry leases for the use of any one aircraft can be in place at one time). In such instances, each individual Operator is required to have an appropriate RVSM authorization issued in its own name in order for that Operator to have access to RVSM airspace. For example, if an aircraft owner elects to lease the aircraft to a part 135 certificate holder for charter operations but retain operational control of the aircraft for its own part 91 flights, then the part 135 certificate holder will hold its RVSM authorization under its OpSpec for those charter operations, and the owner will simultaneously hold a separate RVSM LOA for its own part 91 operations.
3.5 Who is a “Responsible Person,” and What Duties Does this Person Fulfill, Under an RVSM Authorization?
3.5.1 Who is a Responsible Person and How Does this Relate to RVSM Authorizations? For part 91 RVSM applicants, the application for authorization to operate within RVSM airspace must include the designation of a Responsible Person, and may further include the designation of a separate RVSM-POC, as follows:
3.5.1.1 The Operator should designate a person(s) who has the legal authority to sign the RVSM authorization on behalf of the Operator and who has adequate knowledge of RVSM requirements, policies, and procedures. That person may be the individual person who will be the Operator, or, if the Operator is a legal entity, then an officer or employee of that entity, or a separate person who that individual person or entity has contracted with in order to act on behalf of the individual person or legal entity with respect to the RVSM authorization.
3.5.1.2 The Operator should also designate a person(s) to act as a contact person who has actual day-to-day knowledge of the RVSM-Compliant Aircraft operations and RVSM airworthiness status the FAA may contact to gather such information when such a need arises.
3.5.1.3 The Operator may use one individual to fulfill both roles as described in paragraphs 3.5.1.1 and 3.5.1.2, or the Operator may elect to designate separate persons to fulfill these roles.
3.6.4 RVSM Height Monitoring.
3.5.1.4 Whoever the Operator designates to fulfill the role described in paragraph 3.5.1.1 will be designated as the “Responsible Person,” and that Responsible Person will sign LOAs, as appropriate.
3.5.1.5 If the Operator chooses to use separate individuals, then the person fulfilling the role described in paragraph 3.5.1.2 will be designated as the “RVSM-POC.” In such event, the separate person designated as the RVSM-POC (i.e., someone who has not also been designated as a Responsible Person) will not have any authority to sign the RVSM authorization on behalf of the Operator. Additionally, if an Operator has designated a separate RVSM-POC, then that is the individual the FAA should first contact with respect to the Operator’s RVSM-Compliant Aircraft operations and RVSM airworthiness status.
3.5.1.6 In any event, the Responsible Person and/or the RVSM-POC should be a person having on-going knowledge of the operations of the aircraft under the RVSM authorization.
3.5.1.7 Additionally, it generally is not appropriate to designate an “Agent for Service” with respect to RVSM authorizations being issued to part 91.
Note: See LOA template B046 for further details regarding Responsible Persons.
3.6 What Other Issues Should be Addressed by Applicants with Respect to Requests for RVSM Authorizations?
3.6.1 RVSM Configuration List. The applicant should provide a configuration list, for the applicable aircraft, which details components and equipment relevant to RVSM operations. (See Appendix A for a discussion of equipment for RVSM operations.)
3.6.2 Minimum Equipment List (MEL). Operators conducting operations under an MEL adopted from the Master Minimum Equipment List (MMEL) should include items pertinent to operating in RVSM airspace.
3.6.3 Operating History. An operating history should be included in the application, if applicable. The applicant should show any events or incidents related to poor height-keeping performance indicating weaknesses in training, procedures, maintenance, or the aircraft group intended to be used.
3.6.4 RVSM Height Monitoring. RVSM height monitoring was implemented with the establishment of RVSM airspace to ensure implementation and continued operation of RVSM meets safety objectives. Compliant height-keeping performance of airplanes is a key element in ensuring safe operations in RVSM airspace. RVSM is a “performance-
2. To determine the number of airframes each Operator is required to… › 2. To determine the number of airframes each Operator is required to…
based” operation requiring ongoing, independent monitoring to ensure that the RVSM airspace airplane population adheres to stringent altimetry system requirements.
Note 1: The requirement for operational flight monitoring may not be included in the Operator’s ICA.
Note 2: For a detailed discussion of RVSM height monitoring, see the RVSM Height Monitoring Guide for U.S. Operators on the FAA’s RVSM Web page in the Monitoring Requirements and Procedures section.
3.6.4.1 Who must participate in RVSM height monitoring? All Operators wishing to conduct operations in RVSM-designated airspace are required to participate in RVSM height monitoring.
1. Existing rule part 91, § 91.180 requires operations within airspace designated as RVSM to “comply with the minimum standards of appendix G of this part.” Part 91 appendix G, section 2(d), (e), and (f) stipulate the requirements for ASE containment.
2. Part 91 appendix G, section 3 stipulates how the Operator, in a manner prescribed by the Administrator, must provide evidence “it is capable to operate and maintain each aircraft or aircraft group for which it applies for approval to operate in RVSM airspace.” Height monitoring is the method prescribed to verify ASE remains within required performance limits.
3.6.4.2 When do I have to get my airplanes monitored? U.S.-registered Operators are required to conduct initial height monitoring within 6 months of the authorization date of issue and must conduct height monitoring every 2 years or within intervals of 1,000 flight hours, whichever period is longer.
1. Monitoring is not required prior to being granted operational approval.
2. Evidence of previous successful monitoring of an airplane transfers to a new owner and may be used to meet the monitoring requirements.
3. When calculating the 1,000 hour provision of the minimum monitoring requirement, the calculation of the flight time should be from the last satisfactory height monitoring date on record.
3.6.4.3 How many airplanes need to be monitored?
1. An Operator with multiple airplanes may not need to have all airplanes monitored. For height monitoring, only a sampling of airframes of each airplane type need to be monitored.
2. To determine the number of airframes each Operator is required to have monitored, use the RVSM Minimum Monitoring Chart. The
• Evidence provided through another ICAO-sponsored Regional Monitoring… › • Evidence provided through another ICAO-sponsored Regional Monitoring…
current version of this chart can be found on the FAA’s RVSM Web page in the Monitoring Requirements and Procedures section.
Note: An Operator that is unable to meet the minimum height monitoring requirements within the specified time frame should contact the responsible CHDO/CMO/FSDO/IFO prior to exceeding the specified time frame. (See paragraph 3.6.4, Note 1.)
3.6.4.4 How do I get my airplanes monitored?
1. An Operator may choose to fly with a trained technician from an FAA-approved RVSM monitoring support provider utilizing a Global Positioning System (GPS)-based monitoring unit (GMU) onboard the airplanes.
2. An Operator may fly an airplane through an established ground-based height measuring system. Currently ground-based systems exist in:
• North America, Airplanes Geometric Height Monitoring Elements (AGHME) (requires Mode-S equipment); or • Approved ground-based height measuring systems in other regions (e.g., Europe or Japan).
3. An RVSM-authorized aircraft equipped and operating with Automatic Dependent Surveillance-Broadcast (ADS-B) Out avionics meeting the performance requirements of § 91.227 at an RVSM altitude where ADS-B height monitoring is provided.
Note: The height monitoring requirements are globally harmonized and the ICAO Regional Monitoring Agency for North America is the North American Approvals Registry and Monitoring Organization (NAARMO). The NAARMO coordinates RVSM monitoring results with the more than 30 other ICAO Regional Monitoring agencies throughout the world.
3.6.4.5 How can I verify if my airplanes were monitored in the last 2 years?
1. An Operator that has a valid RVSM authorization can check the RVSM Approvals database to determine if their last valid monitoring occurred within the last 2 years.
2. The following methods satisfy monitoring requirements:
• Entry of successful AGHME or other approved ground-based monitoring system result in the U.S. RVSM Approvals database.
• A report of a successful monitoring supplied by an FAA-approved, GPS-based provider.
• Evidence provided through another ICAO-sponsored Regional Monitoring Agency, such as EUROCONTROL.
3. For North American Operators, the database can be accessed from the FAA RVSM Web site under the section RVSM Documentation or on the FAA’s NAARMO website at: https://www.faa.gov/air_traffic/separation_standards/naarmo/rvsm _approvals/.
3. Aircraft being utilized for mercy or humanitarian purposes. › 3. Aircraft being utilized for mercy or humanitarian purposes.
3.6.4.6 RVSM Height Monitoring Plan. Operators, upon application, should submit a monitoring plan including:
1. Number and identification (registration number/serial number) of airplanes to be monitored.
2. Expected time frame for completion of monitoring requirements.
3. Expected method for monitoring.
3.6.5 Can Non-RVSM Aircraft Be Accommodated in RVSM Airspace? Operators must be authorized and aircraft must be certified to fly in designated RVSM airspace with limited exceptions.
3.6.5.1 In Domestic U.S., Alaska Offshore Airspace, the following aircraft can be accommodated on a workload-permitted basis. The vertical separation standard applied between aircraft not approved for RVSM and all other aircraft must be 2,000 ft:
1. Department of Defense (DOD) aircraft.
2. Flights conducted for aircraft certification and development purposes.
3. Active air ambulance flights utilizing a “MEDEVAC” call sign.
4. Aircraft climbing/descending through RVSM flight levels (FL) (without intermediate level off) to/from FLs above RVSM airspace.
5. Foreign State (government) aircraft.
3.6.5.2 In addition to the accommodation categories listed in paragraph 3.6.5.1, in U.S.-controlled oceanic airspace, the following aircraft can be accommodated on a workload-permitted basis:
1. Aircraft being initially delivered to the State of Registry or Operator.
2. Aircraft that was formerly RVSM-approved but has experienced an equipment failure and is being flown to a maintenance facility for repair in order to meet RVSM requirements and/or obtain approval.
3. Aircraft being utilized for mercy or humanitarian purposes.
3.6.5.4 The procedures for accommodation of non-RVSM aircraft in RVSM…
3.6.5.3 An aircraft or Operator not authorized for RVSM operations or an Operator/aircraft without operable RVSM equipment is referred to as non-RVSM. If either the Operator or the aircraft or both have not received RVSM authorization, the Operator or dispatcher must not file the RVSM equipment code in the flight plan. The pilot of non-RVSM aircraft must inform the controller of the lack of RVSM approval in accordance with the direction provided in the FAA Aeronautical Information Manual (AIM), paragraph 4-6-8, Pilot/Controller Phraseology.
3.6.5.4 The procedures for accommodation of non-RVSM aircraft in RVSM airspace for operations in Domestic U.S., Alaska Offshore Airspace and the San Juan Flight Information Region (FIR) are contained in the FAA Aeronautical Information Manual (AIM), Section 6, paragraph 4-6-10. For operations within oceanic airspace, see the U.S. Aeronautical Information Publication (AIP), Enroute, Section 7.
Note › Note
CHAPTER 4. SUBMITTING AN APPLICATION FOR RVSM AUTHORIZATION.
4.1 What is the First Step an Applicant May Consider Taking When Applying for an RVSM Authorization?
4.1.1 Should an Applicant Request a Preapplication Meeting? The regulations do not require an applicant participate in a preapplication meeting. However, an applicant may wish to request a preapplication meeting if the applicant is unfamiliar with the application process, seeks additional information with respect to RVSM authorizations, or has other questions concerning how to move forward with the application process.
4.1.2 Where Should an Applicant Request a Preapplication Meeting? An applicant who wishes to request a preapplication meeting should make initial contact with the FAA office as follows.
1. Parts 91K, 121, 125 (A125 LODA holders), and 135 Operators should notify the jurisdictional CHDO, CMO, or FSDO of its intent to obtain authorization for RVSM operations. (See FAA Order 8900.1, Volume 3, Chapter 2, Section 2, paragraph 3-55.)
2. In accordance with FAA Order 8900.1, Volume 3, Chapter 2, Section 2, part 91 Operators apply for an RVSM LOA to the FSDO with a service area covering the Operator’s primary business address. If your primary business address is not in the United States, apply to the responsible IFO’s geographic Area of Responsibility (AOR) on the following Web site: http://www.faa.gov/about/office_org/field_offices/ifo/. Once on the Web site, click on the service area under each IFO for additional information.
4.2 What are the Applicable Steps and Information Required to Seek an RVSM Authorization? Prior to making a request for service, each applicant should review the information provided in Chapter 3 as well as the RVSM decision Matrix in Figure 4-1 to determine if the applicant should apply procedures for Authorization Group I, Authorization Group II, or Authorization Group III. Each of these groups is summarized in paragraph 4.2, with the RVSM-Decision Matrix (Figure 4-1) provided for detailed examples and information for the application process.
Note: The written request discussed in paragraphs 4.2.1.2, 4.2.2.2, and 4.2.3.2 is your letter to the CHDO requesting service. Using the RVSM Decision Matrix in Figure 4-1, you should identify the specific RVSM Authorization Group for your request. Include sufficient administrative information to allow the FAA inspector to make the necessary form field entries when creating the authorization document. For part 91 LOAs, samples of the needed administrative information is located on the FAA Web site, http://www.faa.gov/air_traffic/separation_standards/rvsm/documentation. Scroll down to the “Getting Started” section and locate the appropriate document titled Information Sheet for Part 91 RVSM Letter of Authorization (LOA). Use of the information sheet will help you organize required information needed for authorization. Providing sufficient information to the CHDO can assist in
3. Provides such additional information as necessary to evidence… › 3. Provides such additional information as necessary to evidence…
streamlining the application process and help prevent processing delays while the inspector waits for the needed information to be submitted.
4.2.1 What are the General Steps an Applicant will take when its Application Falls Within RVSM Authorization Group I, RVSM Authorization Amendments?
4.2.1.1 Prior to making a request for service for an authorization amendment, each existing authorization holder should make a positive determination none of the previously accepted RVSM Authorization Elements are changing.
4.2.1.2 That authorization holder should then submit a written request to the responsible FSDO, CHDO, or IFO that:
1. States which of the applicable administrative changes are occurring;
2. Further affirmatively states none of the previously accepted RVSM Authorization Elements forming the basis for the initial issuance of the affected RVSM authorization have changed or are changing; and
3. Requests the issuance of an amendment to the existing RVSM authorization acknowledging the administrative change being made.
4.2.1.3 The authorization holder should also provide such further information as the FSDO, CHDO, or IFO may request in order to efficiently process the request.
4.2.2 What are the General Steps an Applicant will take when its Application Falls Within RVSM Authorization Group II, RVSM Authorization Based on One or More Existing RVSM Authorization Elements?
4.2.2.1 The applicant should make a positive determination the existing or new proposed RVSM Operator is seeking an RVSM authorization utilizing at least one previously approved/accepted RVSM Authorization Element.
4.2.2.2 Submit a written request to the responsible FSDO, CHDO, or IFO that:
1. Provides complete documentation of an RVSM-compliant program, including written information evidencing the specific aircraft meets the requirements of an RVSM-Compliant Aircraft;
2. Further specifically states previously accepted RVSM-Knowledgeable Pilots requirements will be used with respect to the operation of the proposed approved RVSM Aircraft in RVSM airspace, as applicable;
3. Provides such additional information as necessary to evidence compliance with new or different RVSM-Knowledgeable Pilots
requirements (or to be able to gain such approvals) and any of the other RVSM Authorization Elements listed in Chapter 3; and
4. Asks for the issuance of an RVSM authorization applying to the operation of the aircraft by that proposed RVSM Operator.
3. Change in the registration markings of an RVSM-Compliant Aircraft… › 3. Change in the registration markings of an RVSM-Compliant Aircraft…
4.2.2.3 Provide such further information as the FSDO, CHDO, or IFO may request in order to efficiently process the request.
4.2.3 What are the General Steps an Applicant will take when its Application Falls Within RVSM Authorization Group III, RVSM Authorization Not Based on One or More Existing RVSM Authorization Elements?
4.2.3.1 In the event a proposed new or existing approved RVSM Operator seeks the issuance of an RVSM authorization not based on any existing RVSM Authorization Element, then neither Authorization Group I nor II above will apply.
4.2.3.2 The applicant should submit a written request to the responsible FSDO, CHDO, or IFO with sufficient evidence to show its ability to comply with each of the RVSM Authorization Elements in Chapter 3, and the FSDO, CHDO, or IFO should process the request as a new and unique request by reviewing all of the materials provided by the applicant to ensure each of the RVSM Authorization Elements have been met.
4.2.3.3 The applicant should also provide such further information as the FSDO, CHDO, or IFO may request in order to efficiently process the request.
4.2.4 The RVSM Matrix. A detailed description of Figure 4-1 is provided in paragraph 2.4.
Figure 4-1. RVSM Decision Matrix
RVSM DECISION MATRIX
AUTHORIZATION GROUP I:
RVSM AUTHORIZATION AMENDMENTS
• • The following changes are considered to be administrative in nature only. This group only applies in circumstances where a previously authorized RVSM Operator of the previously accepted RVSM Authorization Elements are remaining the same.
and each
I. A. Examples of Requested Action/Nature of Change
1.
2.
3.
Change in the primary business address of an RVSM-Compliant Aircraft and/or RVSM authorization holder. Change in an existing RVSM Operator’s designated Responsible Person (or RVSM-Authorized Representative or RVSM-Point of Contact (POC)). Change in the registration markings of an RVSM-Compliant Aircraft being operated by an existing RVSM authorization holder.
4. If an existing RVSM authorization holder has made a written… › 4. If an existing RVSM authorization holder has made a written…
RVSM DECISION MATRIX
4. Removal of an RVSM-Compliant Aircraft from an existing RVSM authorization multiple RVSM-Compliant Aircraft listed.
having
I. B. Applicable Steps and Information Required from RVSM Authorization Holder
1.
2.
3.
4.
Prior to making a request for service for an authorization amendment, each existing authorization holder should make a positive determination none of the previously accepted RVSM Authorization Elements are changing. That authorization holder should then submit a written request to the responsible FSDO, CHDO, or IFO that: a. States which of the applicable administrative changes are occurring; b. Further affirmatively states none of the previously accepted RVSM Authorization
Elements forming the basis for the initial issuance of the affected RVSM authorization have changed or are changing; and c. Requests the issuance of an amendment to the existing RVSM authorization
acknowledging the administrative changes being made. If the nature of the requested amendment is to change the primary business address from one FSDO, CHDO, or IFO service area to another, it must notify, in writing, the losing (previously responsible) FSDO, CHDO, or IFO of the new physical location and mailing address within 30 calendar-days following relocation. The losing FSDO, CHDO, or IFO will then request the WebOPSS Help Desk move the Operator's database to the responsible receiving FSDO, CHDO, or IFO. The losing FSDO, CHDO, or IFO will also notify the receiving FSDO, CHDO, or IFO of the change. The receiving FSDO, CHDO, or IFO will then update and reissue the Operator's A001 template to reflect the new address, and the receiving FSDO, CHDO, or IFO becomes the responsible FSDO, CHDO, or IFO for processing new LOAs for that Operator. The authorization holder should also provide such further information as the FSDO, CHDO, or IFO may request in order to efficiently process the request.
I. C. Applicable Procedures the Responsible FSDO, CHDO, or IFO Will Follow Upon a Request for an Administrative Change to an Existing RVSM Authorization
1.
2.
3.
4.
Review the request and supporting documentation received from the RVSM authorization holder to determine if it appears an amended RVSM authorization amendment is warranted. Re-issue the amended RVSM authorization identical to the initial RVSM authorization in all respects other than reflecting the new amended information; and If the nature of the requested amendment is to change the primary business address from one FSDO service area to another, see the additional applicable guidance in FAA Order 8900.1, Volume 3, Chapter 2, Section 2, Responsibility of Part 91 Letters of Authorization (LOA). If an existing RVSM authorization holder has made a written affirmation none of the underlying previously accepted RVSM Authorization Elements has changed or will change, and there is no other information provided to the FSDO raising any questions or concerns with respect to the on-going validity or applicability of those RVSM Authorization Elements, then, subject to paragraph 2.4.4, the FSDO, CHDO, or IFO should issue the requested amendment without further inspections being required.
a. Provides complete documentation of an RVSM compliance program,… › a. Provides complete documentation of an RVSM compliance program,…
RVSM DECISION MATRIX
AUTHORIZATION GROUP II:
RVSM AUTHORIZATION BASED ON ONE OR MORE EXISTING APPROVED RVSM AUTHORIZATION ELEMENTS
• The following RVSM authorizations are new authorizations. • This group will normally apply to a new or proposed RVSM Operator seeking the issuance of an RVSM authorization for an aircraft already an RVSM-Compliant Aircraft or where the new RVSM Operator will be utilizing previously accepted RVSM-Knowledgeable Pilots requirements with respect to its operations of that specific aircraft.
II. A. Examples of Requested Action/Nature of Change
1.
2.
3.
There is a change in the legal status or identity of the business entity that is the approved RVSM Operator, but the Responsible Person, RVSM Authorized Representative, and/or RVSM Contact Person and each of the approved RVSM Authorization Elements are remaining the same.
a. One example of this situation may occur where an Operator is converted from an
S-corporation to a limited liability company, for example, under applicable state law, but no other changes are occurring. b. Another example may occur where the ownership and operation of an aircraft is
transferred from one company to a legal affiliate, but there are no other changes occurring. A new proposed RVSM Operator will be using an existing RVSM-Compliant Aircraft, together with a previously accepted RVSM-Knowledgeable Pilots requirements. Examples of this type of situation may include:
a. An Operator takes delivery of a newly-manufactured aircraft type certified as
RVSM-compliant. b. An approved RVSM aircraft is being operated under an RVSM authorization issued to a
part 135 air carrier, and the underlying owner or a separate lessee will occasionally use that specific aircraft while it is maintained under part 135 air carrier’s Maintenance Program and/or the same RVSM-Knowledgeable Pilots requirements. c. A group of underlying owners or lessees use an RVSM-Compliant Aircraft, each
maintaining their own operational control of that aircraft pursuant to a dry lease, while also utilizing the same previously accepted RVSM-Knowledgeable Pilots requirements. An existing or new proposed approved RVSM Operator seeks an RVSM authorization and will be utilizing one or more existing approved RVSM Authorization Elements.
a. An example may be where an existing RVSM Operator seeks to add a new proposed
RVSM-Compliant Aircraft to an existing RVSM authorization where that Operator will continue to use previously accepted RVSM-Knowledgeable Pilots requirements.
II. B. Applicable Steps and Information Required from RVSM Authorization Applicant
1.
2.
Make a positive determination that the existing or new proposed RVSM Operator is seeking an RVSM authorization utilizing at least one previous RVSM Authorization Element (i.e., an existing RVSM-Compliant Aircraft and/or RVSM-Knowledgeable Pilots requirements). Submit a written request to the responsible FSDO, CHDO, or IFO that:
a. Provides complete documentation of an RVSM compliance program, including written
information evidencing the specific aircraft meets the requirements of an RVSM-Compliant Aircraft;
RVSM DECISION MATRIX
b. Further specifically states previously accepted RVSM-Knowledgeable Pilots
requirements will be used with respect to the operation of the proposed approved RVSM Aircraft in RVSM airspace, as applicable; c. Provides such additional information as necessary to evidence compliance with new or
AUTHORIZATION GROUP III: › In the event a proposed new or existing approved RVSM Operator seeks…
different RVSM-Knowledgeable Pilots requirements (or to be able to gain such approvals); and d. Asks for the issuance of an RVSM authorization applying to the operation of the aircraft
by that proposed RVSM Operator. 3. Provide such further information as the FSDO, CHDO, or IFO may request in order to efficiently process the request.
II. C. Applicable Procedures to be Followed by the Responsible FSDO, CHDO, or IFO
1. Review the request and supporting documentation received from the RVSM authorization applicant to determine if it appears the requested RVSM authorization is warranted. 2. To the extent the RVSM applicant has provided written documentation evidencing the Operator will be using a previously accepted RVSM Authorization Element, and accept that RVSM Authorization Element as a valid basis for the issuance of the new RVSM authorization, and to the extent the applicant has presented a proposed RVSM Authorization Element not previously reviewed and accepted, conduct such additional review and research with respect to that RVSM Authorization Element only as is required to issue the new RVSM authorization. 3. If an RVSM applicant has made a written affirmation one or more of the underlying previously accepted RVSM Authorization Elements have not changed or will not change, there is no other information provided to the FSDO, CHDO, or IFO raising any questions or concerns with respect to the on-going validity or applicability of those RVSM Authorization Elements, and the applicant has otherwise presented sufficient evidence of compliance with the requirements of the remaining RVSM Authorization Elements, then, subject to paragraph 2.4.4, the FSDO, CHDO, or IFO should issue the requested amendment without further inspections being required.
AUTHORIZATION GROUP III:
RVSM AUTHORIZATION NOT BASED ON ONE OR MORE EXISTING RVSM AUTHORIZATION ELEMENTS
In the event a proposed new or existing approved RVSM Operator seeks the issuance of an RVSM authorization not based on any existing RVSM Authorization Element, then neither Authorization Group I nor II above will apply, the applicant should submit sufficient evidence to show its ability to comply with each of the RVSM Authorization Elements, and the FSDO, CHDO, or IFO should process the request as a new and unique request by reviewing all of the materials provided by the applicant to ensure each of the RVSM Authorization Elements have been met.
Note › Note
CHAPTER 5. FAA REVIEW AND EVALUATION OF RVSM APPLICATIONS.
5.1 What is the General Process the FAA will Follow Upon Submission of the Request for an RVSM Authorization or Amended Authorization? Once application is made, the FAA will begin the process of review and evaluation of the documentation submitted. When the FAA determines the airworthiness and operational requirements of the application are met, the FAA will proceed with issuing the authorization.
5.2 What are the Applicable Forms of the RVSM Authorization Documents?
5.2.1 Parts 121, 125, and 135 Operators. Authorization for parts 121, 125, and 135 Operators to operate in RVSM airspace should be granted through the issuance of an OpSpec paragraph from Part B (En Route Authorizations, Limitations, and Procedures) and Part D (Aircraft Authorization). Each aircraft for which the Operator is granted authority should be listed in the OpSpecs. Authorization to conduct RVSM operations in an RVSM area of operations new to the Operator should be granted by adding the Part B RVSM OpSpecs paragraph number to the appropriate area of operations in the Part B paragraph: Authorized Areas of En Route Operation Limitations and Procedures.
5.2.2 Part 129 Operators. The operational authorization of RVSM for part 129 is provided by the State of the Operator. OpSpec A003 is used to confirm that the foreign air carrier has operational approval. The State of the Operator must have regulation and supporting guidance documents for the issuance of RVSM. The following are examples of guidance documents the FAA considers to be consistent with ICAO standards on RVSM.
5.2.2.1 The current edition of this advisory circular (AC) (91 85, Authorization of Aircraft and Operators for Flight in Reduces Vertical Separation Minimum Airspace); and Joint Aviation Authority (JAA) Temporary Guidance TGL-6.
Note: For part 129 Operators, inspector guidance for paragraph A003 is contained in FAA Order 8900.1, Volume 12, Chapter 2, Section 3.
5.2.3 Part 91K Operators. Part 91K Operators’ authorization to operate in RVSM airspace should be granted through the issuance of an MSpecs paragraph from Part B and Part D. Each aircraft for which the Operator is granted authority should be listed in MSpecs. Authorization to conduct RVSM operations in an RVSM area of operations new to the Operator should be granted by adding the Part B RVSM MSpecs paragraph number to the appropriate area of operations in the Part B paragraph.
5.2.4 Parts 91 and 125 (LODA Holder) Operators. Part 91 Operators and part 125 Operators holding a LODA should be issued a LOA when the initial authorization process has been completed.
Note: LODA is a formal authorization issued by the FAA CHDO, authorizing a deviation from specified sections of part 125 and identified in WebOPSS (125M database) as an A125 LODA operator.
5.2.5 LOA Exemptions. Operators issued OpSpecs are not required to obtain an LOA for those operations conducted under part 91 provided that:
5.3.4 Review Relevant OpSpec/MSpec/LOA Paragraphs.
1. The aircraft is operated under the Operator name listed on the OpSpecs.
2. The flight is conducted in an area of operations listed in the OpSpecs.
3. The aircraft is operated under the conditions under which the OpSpecs were granted (e.g., if the Operator holds 121 or 135 OpSpecs, then the pilots used for the part 91 operation must have received part 121 or 135 training.)
4. Each part 91 operation, not associated with a certificated operator, will need a LOA to operate in RVSM airspace.
5.3 What are the Conditions That Would Require the Removal of an RVSM Authorization?
Note: Examples of reasons for amendment, revocation, or restriction of RVSM authorization include, but are not limited to, the reasons listed in part 91 appendix G, section 7.
5.3.1 Height-Keeping Errors. The incidence of height-keeping errors tolerated in an RVSM environment is very small. It is incumbent upon each operator to take immediate action to rectify the conditions causing the error. The operator should also report the event to the FAA within 72 hours with initial analysis of causal factors and measures to prevent further events. The FAA should determine the requirement for follow-up reports. Errors which should be reported and investigated are: Total Vertical Error (TVE) equal to or greater than ±300 ft (±90 m), ASE equal to or greater than ±245 ft (±75 m), and assigned altitude deviation (AAD) equal to or greater than ±300 ft (±90 m).
5.3.2 Error Categories. Height-keeping errors fall into two broad categories: 1) errors caused by malfunction of aircraft equipment, and 2) operational errors. An operator who commits one or more error(s) of either variety may be required to forfeit authority for RVSM operations. If a problem is identified related to one specific aircraft type, then RVSM authority may be removed for the operator for that specific type.
5.3.3 Effective, Timely Response. The operator should make an effective, timely response to each height-keeping error. The FAA may consider removing RVSM operational authorization if the operator response to a height-keeping error is not effective or timely. The FAA should also consider the operator’s past performance record in determining the action to take. If an operator shows a history of operational and/or airworthiness errors, then authorization may be removed until the root causes of these errors are shown to be eliminated and RVSM programs and procedures are shown to be effective. The FAA will review each situation on a case-by-case basis.
5.3.4 Review Relevant OpSpec/MSpec/LOA Paragraphs. Operators may also consider reviewing all relevant paragraphs of their respective OpSpec, MSpec, or LOA (e.g., A001) for other reasons which may affect RVSM authorizations.
5.4 What Happens if I Change RVSM Equipment After Operational Authorization has been Granted? Any change to an RVSM Critical Component or RVSM System as defined in the initial application must be reported to the responsible office for evaluation. The responsible office will determine if the aircraft is RVSM compliant.
A.11 RVSM Airworthiness Approval … A-30
APPENDIX A. RVSM AIRWORTHINESS CERTIFICATION
CONTENTS
Paragraph Page
A.1 Introduction … A-2
A.2 RVSM Flight Envelopes … A-4
A.3 Group and Non-Group Aircraft … A-6
A.4 Aircraft Systems—Group and Non-Group Aircraft … A-6
A.5 Altimetry System Performance … A-9
A.6 Aircraft System Configurations: Older “Legacy” Airframes … A-11
A.7 Altimetry System Performance Substantiation … A-14
A.8 Altimetry System Component Error Budget … A-16
A.9 Establishing and Monitoring Static Source Errors … A-24
A.10 Maintenance Requirements … A-27
A.11 RVSM Airworthiness Approval … A-30
8. Basic RVSM Envelope. › 8. Basic RVSM Envelope.
A.1 Introduction.
A.1.1 General. This Appendix provides guidance on the aircraft airworthiness certification
process for Reduced Vertical Separation Minimum (RVSM) compliance. Key elements necessary to substantiate the aircraft systems performance required for RVSM certification are summarized. Differences between a Group and Non-Group aircraft certification program are presented. A comprehensive discussion of altimetry system error (ASE) and ASE variation is also provided.
Note: For additional information on obtaining RVSM airworthiness certification contact the appropriate FAA Field Office serving your geographic area for guidance. Contact information for Aircraft Certification Offices (ACO) can be found on the FAA Web site at www.faa.gov.
A.1.2 Definitions.
1. Aircraft Group. A group of aircraft of nominally identical design and build with respect to all details that could influence the accuracy of height-keeping performance.
2. Air Data Sensor. Line replaceable units designed to detect air data characteristics (e.g., pressure, temperature, etc.) to support the air data system of the aircraft.
3. Air Data System. Systems used to collect and process air data characteristics from various sensors to compute critical air data parameters (e.g., altitude, airspeed, height deviation, and temperature) for use by the pilot and other systems in the aircraft.
4. Altimetry System Error (ASE). The difference between the pressure altitude displayed to the flightcrew when referenced to International System of Units (SI) standard ground pressure setting (29.92 in. Hg/1013.25 hPa) and free stream pressure altitude.
5. Assigned Altitude Deviation (AAD). The difference between the altitude transmitted by a Mode C transponder and the assigned altitude/flight level (FL).
6. Automatic Altitude Control System. Any system designed to automatically control the aircraft to a referenced pressure altitude.
7. Avionics Error. The error in the processes of converting the sensed pressure into an electrical output, of applying any static source error correction (SSEC) as appropriate, and of displaying the corresponding altitude.
8. Basic RVSM Envelope. The range of Mach numbers and gross weights within the altitude ranges FL 290 to FL 410 (or max available altitude) where an aircraft is expected to operate most frequently.
21. W/δ. › 21. W/δ.
9. Derivative Aircraft. Aircraft of the same model type, certified under the same type certificate (TC). The aircraft may have different exterior dimensions, such as fuselage length and wing span, but share the same altimetry system architecture. In addition, derivative aircraft share the same SSEC at RVSM flight levels. In most cases, derivative aircraft will have differing flight envelopes, so the RVSM flight envelope defined for the Group must be carefully constructed such that the performance of all models within the Group is captured.
10. Full RVSM Envelope. The entire range of operational Mach numbers, W/δ, and altitude values over which the aircraft is operated within RVSM airspace.
11. Height-Keeping Capability. Aircraft height-keeping performance expected under nominal environmental operating conditions with proper aircraft operating practices and maintenance.
12. Height-Keeping Performance. The observed performance of an aircraft with respect to adherence to a flight level.
13. Instruction for Continued Airworthiness (ICA). Documentation giving instructions and requirements for the maintenance essential to the continued airworthiness of an aircraft.
14. Non-Group Aircraft. An aircraft for which the operator applies for approval on the characteristics of the unique airframe rather than on a group basis.
15. Residual Static Source Error (SSE). The amount by which SSE remains undercorrected or overcorrected after application of an SSEC.
16. Reduced Vertical Separation Minimum (RVSM). Designated airspace, typically between FL 290 and FL 410, where 1000’ vertical separation between aircraft is applied. This airspace is considered special qualification airspace.
17. Static Source Error (SSE). The difference between the pressure sensed by the aircraft static source and the undisturbed ambient pressure.
18. Static Source Error Correction (SSEC). A correction applied to the altimetry system to produce minimal residual SSE.
19. Total Vertical Error (TVE). Vertical geometric difference between the actual pressure altitude flown by an aircraft and its assigned pressure altitude (FL).
20. Worst Case Avionics. The combination of tolerance values, specified by the manufacturer for the altimetry fit into the aircraft, which gives the largest combined absolute value of avionics errors.
21. W/δ. Aircraft weight, W, divided by the atmospheric pressure ratio, δ.
A.1.3.5 Over the RVSM altitude range, it is an accurate approximation… › A.1.3.5 Over the RVSM altitude range, it is an accurate approximation…
A.1.3 An Explanation of W/δ.
A.1.3.1 Throughout this Appendix, there are multiple references to the performance parameter W/δ. The following discussion is provided for the benefit of readers who may not be familiar with the use of this parameter.
A.1.3.2 It would be difficult to show all of the gross weight, altitude, and speed conditions constituting the RVSM envelope(s) on a single plot. This is because most of the speed boundaries of the envelopes are a function of both altitude and gross weight. As a result, a separate chart of altitude vs. Mach would be required for each aircraft gross weight. Aircraft performance engineers commonly use the following technique to solve this problem.
A.1.3.3 For most aircraft with RVSM altitude capability, the required flight envelope can be collapsed to a single chart, with good approximation, by use of the parameter W/δ (weight divided by atmospheric pressure ratio). This fact is due to the relationship between W/δ and the fundamental aerodynamic variables M and lift coefficient as shown below.
W/δ =1481.4 CL M2 SREF
where δ = ambient pressure at flight altitude
divided by sea level standard pressure
of 29.92126 inches Hg.
W/δ = Weight over Atmospheric Pressure Ratio.
CL = Lift Coefficient (CL = L/qSREF).
L = Lift (in cruise flight L is equal to W).
q = Dynamic Pressure, q = 1481.4M2 δ.
Dynamic pressure is in the form of lbs/ft2.
M = Mach number.
SREF = Reference Wing Area in square feet.
W is the weight in pounds.
A.1.3.4 As a result, the flight envelope may be collapsed into one chart by simply plotting W/δ, rather than altitude, versus Mach number. Since δ is a fixed value for a given altitude, weight can be obtained for a given condition by simply multiplying the W/δ value by δ.
A.1.3.5 Over the RVSM altitude range, it is an accurate approximation to assume that position error is uniquely related to Mach number and W/δ for a given aircraft.
A.2.3.1 For the basic RVSM envelope, the upper Mach boundary may be… › A.2.3.1 For the basic RVSM envelope, the upper Mach boundary may be…
A.2 RVSM Flight Envelopes.
A.2.1 General. For the purposes of RVSM approval, the aircraft flight envelope is considered in
two parts: 1) the full RVSM envelope, and 2) the basic RVSM envelope. The basic RVSM envelope is the part of the flight envelope where aircraft operate the majority of time. The full RVSM envelope is the entire range of operational Mach numbers, W/δ, and altitude values over which the aircraft is operated within RVSM airspace. In general, the full RVSM envelope comprises parts of the flight envelope where the aircraft operates less frequently and where a larger ASE tolerance is allowed.
A.2.2 Full RVSM Envelope. The full RVSM envelope will comprise the entire range of
operational Mach number, W/δ, and altitude values over which the aircraft can operate within RVSM airspace. Table A.2-1 establishes the parameters to consider.
Table A.2-1. Full RVSM Envelope Boundaries
Lower Boundary is defined by:
Upper Boundary is defined by:
Altitude FL 290 The lower of the following:
• FL 410 • Airplane maximum certified altitude • Altitude limited by: cruise thrust; buffet; other aircraft flight limitations
Mach or Speed The lower of the following:
• Maximum endurance (holding) speed • Maneuver speed
The lower of the following:
• MMO/VMO (maximum operating speed (Mach/velocity)) • Speed limited by: cruise thrust; buffet; other aircraft flight limitations
Gross Weight The lowest gross weight compatible with operation in RVSM airspace
The highest gross weight compatible with operation in RVSM airspace
A.2.3 Basic RVSM Envelope. The boundaries for the basic RVSM envelope are the same as
those for the full RVSM envelope except in regard to the upper Mach boundary.
A.2.3.1 For the basic RVSM envelope, the upper Mach boundary may be limited to a range of airspeeds over which the aircraft Group can reasonably expect to operate most frequently. The manufacturer or design organization should define this boundary for each aircraft Group. It may be defined as equal to the upper Mach/airspeed boundary defined for the full RVSM envelope or a specified lower value. This lower value should not be less than the Long
A.4.1 Equipment for RVSM Operations. The minimum equipment fit should… › A.4.1 Equipment for RVSM Operations. The minimum equipment fit should…
Range Cruise Mach number plus .04 Mach unless limited by available cruise thrust, buffet, or other aircraft flight limitations.
A.2.3.2 Long Range Cruise Mach number is the Mach for 99 percent of best fuel mileage at the particular W/δ under consideration.
A.3 Group and Non-Group Aircraft.
A.3.1 Group Aircraft. Aircraft comprising a Group must be of nominally identical design and
build with respect to all details that could influence the accuracy of the height-keeping performance. The following conditions should be met:
1. Aircraft should be approved by the same TC, TC amendment, or Supplemental Type Certificate (STC), as applicable.
2. For derivative aircraft, it may be possible to use the database from the parent configuration to minimize the amount of additional data required to show compliance. The extent of additional data required will depend on the nature of the changes between the parent aircraft and the derivative aircraft.
3. The static system of each aircraft should be installed in a nominally identical manner and position. The same SSEC should be incorporated in all aircraft of the Group.
4. The avionics units installed on each aircraft to meet the minimum RVSM equipment requirements (paragraph A.4) should be manufactured to the manufacturer’s same specification, and have the same equipment part number and software part number (or version and revision).
Note: Aircraft which have avionic units which are of a different manufacturer or equipment part number, software part number (or version and revision) may be considered part of the Group if the applicant demonstrates to the appropriate FAA office this standard of avionic equipment provides identical or better system performance.
5. The airframe manufacturer or design organization produced or provided the RVSM data package.
A.3.2 Non-Group Aircraft. If an airframe does not meet the conditions of paragraph A.3.1 to
qualify as a member of a Group or is presented as an individual airframe for approval, then it must be considered as a Non-Group aircraft for the purposes of RVSM approval.
A.4 Aircraft Systems—Group and Non-Group Aircraft.
A.4.1 Equipment for RVSM Operations. The minimum equipment fit should be as presented
below. Additional examples of aircraft systems found on older, “legacy” airframes are presented in paragraph A.6.
A.4.1.1.7 Output to the Automatic Altitude Control and Altitude Alert…
A.4.1.1 Two Independent Altitude Measurement Systems. Each system should be comprised and configured with the following elements:
A.4.1.1.1 Static Sources. Cross-coupled static source/system, provided with ice protection if located in areas subject to ice accretion.
A.4.1.1.2 Altitude Display. Equipment for measuring static pressure sensed by the static source, converting it to pressure altitude and displaying the pressure altitude to the flightcrew.
A.4.1.1.3 Altitude Reporting. Equipment for providing a digitally coded signal corresponding to the displayed pressure altitude, for automatic altitude reporting purposes. The pressure altitude from which the signal is derived must meet the requirements of paragraphs A5.2.1 and A5.2.2, or A5.3.2, as appropriate.
A.4.1.1.4 Altimetry System Components. The altimetry system should comprise all those elements involved in the process of sampling free stream static pressure and converting it to a pressure altitude output. The elements of the altimetry system fall into two main groups:
• Airframe plus static sources (pitot-static probe/static port), including the area around the static sources in the system design that must be maintained.
• Avionics and/or instruments.
A.4.1.1.5 Altimetry System Accuracy. The total altimetry system accuracy should satisfy the requirements of paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, as appropriate.
A.4.1.1.6 Static Source Error Correction (SSEC). If the design and characteristics of the aircraft and altimetry system are such that the standards of paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, are not satisfied by the location and geometry of the static sources alone, then suitable SSEC should be applied automatically within the avionic part of the altimetry system. The design aim for SSEC, whether aerodynamic/geometric or avionic, should be to produce a minimum residual SSE, but in all cases it should lead to satisfaction of the standards of paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, as appropriate.
A.4.1.1.7 Output to the Automatic Altitude Control and Altitude Alert Systems. The altimetry system equipment fit should provide reference signals for automatic altitude control and alerting at selected altitude. These signals should be derived from an altitude measurement system meeting the full requirements of Appendix A. The output may be used either directly or combined with other sensor signals. If SSEC is necessary in order to satisfy the requirements of paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, then an
A.4.1.3 An Altitude Alert System. The altitude alert system should be… › A.4.1.3 An Altitude Alert System. The altitude alert system should be…
equivalent SSEC must be applied to the altitude control output. The output may be an altitude deviation signal, relative to the selected altitude, or a suitable absolute altitude output. Whatever the system architecture and SSEC system, the difference between the output to the altitude control system and the altitude displayed must be minimal.
A.4.1.1.8 System Safety Analysis. During the RVSM approval process, it must be verified analytically that the predicted rate of occurrence of undetected altimetry system failures does not exceed 1 x 10-5 per flight hour. All failures and failure combinations whose occurrence would not be evident from cross-flight deck checks, and which would lead to altitude measurement/display errors outside the specified limits, need to be assessed against this budget. No other failures or failure combinations need to be considered.
A.4.1.1.9 Air Data Systems and Configurations with Multiple Static Source Inputs. Many aircraft are produced with air data systems making use of three or more static source inputs, and/or three or more air data computers (ADC). Such systems (often referred to as “triplex” systems or “voting” schemes) are designed with integrated algorithms that monitor and compare the pressures sensed at the static sources. Sources providing “good” pressure values are used in the calculation of corrected altitude. Such configurations are acceptable provided at least two air data systems meet the requirements of paragraphs A4.1.1.1 through A4.1.1.8. Upon failure of one air data system, a second system must remain fully functional in compliance with the requirements of paragraphs A4.1.1.1 through A4.1.1.8.
A.4.1.2 One Secondary Surveillance Radar (SSR) Altitude Reporting Transponder. Any transponder meeting or exceeding the requirements of Technical Standard Order (TSO) C74( ) or TSO C112( ), as applicable, in accordance with the operational regulations under which the airplane is approved.
• An aircraft may be equipped with one or more transponders. If only one is fitted, it should have the capability for switching to obtain input from either altitude measurement system.
A.4.1.3 An Altitude Alert System. The altitude alert system should be capable of operation from either of the two required independent altitude measurement systems. The altitude alert system may be comprised of one or more line replaceable units (LRU), or it may be an integral part of a flight management system or flight management computer.
A.4.1.4.2 Where an altitude select/acquire function is provided, the…
1. The altitude deviation warning system should signal an alert when the altitude displayed to the flightcrew deviates from selected altitude by more than a nominal value.
• For aircraft for which application for type certification or major change in type design is on or before April 9, 1997, the nominal value must not be greater than ±300 ft (±90 m).
• For aircraft for which application for type certification or major change in type design (e.g., STC) is made after April 9, 1997, the nominal value should not be greater than ±200 ft (±60 m). The overall equipment tolerance in implementing these nominal threshold values should not exceed ±50 ft (±15 m).
A.4.1.4 An Automatic Altitude Control System. The automatic altitude control system is generally comprised of an autopilot with altitude hold mode. The automatic altitude control system should be capable of operation from either of the two required independent altitude measurement systems. Paragraph 6 presents additional options for automatic altitude control configurations found on older, “legacy” aircraft.
A.4.1.4.1 As a minimum, a single automatic altitude control system should be installed which is capable of controlling aircraft height within a tolerance band of ±65 ft (±20 m) about the acquired altitude when the aircraft is operated in straight and level flight under nonturbulent, nongust conditions.
• Aircraft types for which application for type certification is on or before April 9, 1997, which are equipped with an automatic altitude control system with flight management system(FMS)/performance management system inputs allowing variations up to ±130 ft (±40 m) under nonturbulent, nongust conditions do not require retrofit or design alteration.
• If specific tuning is needed for a “legacy” autopilot to meet performance standards in RVSM airspace, this gain scheduling or tuning must not negatively impact the way the autopilot performs in other phases of flight and at non-RVSM altitudes. For example, it is common for older systems to be tuned to meet RVSM tolerance, only to realize they no longer have acceptable vertical performance on a coupled approach.
A.4.1.4.2 Where an altitude select/acquire function is provided, the altitude select/acquire control panel must be configured such that an error of no more than ±25 ft (±8 m) exists between the display selected by the flightcrew and the corresponding output to the control system.
A.5.2.3 Aircraft types for which application for type certification or… › A.5.2.3 Aircraft types for which application for type certification or…
A.5 Altimetry System Performance.
A.5.1 General. The statistical performance statements of ICAO Doc. 9574, Manual on the
Implementation of a 300 m (1,000 ft) Vertical Separation Minimum Between FL 290-FL 410 Inclusive, for a population of aircraft (see Appendix D) are translated into airworthiness standards by assessment of the characteristics of ASE and altitude control. The following standards differ in some respects from that document, but they are consistent with the requirements of RVSM and in accordance with 14 CFR part 91 appendix G, section 2.
A.5.2 Group Approval.
A.5.2.1 The requirements in the basic RVSM envelope are as follows:
1. At the point in the basic RVSM envelope where ASEmean reaches its largest absolute value, the absolute value should not exceed 80 ft (25 m).
2. At the point in the basic RVSM envelope where ASEmean plus ASE3 SD reaches its largest absolute value, the absolute value should not exceed 200 ft (60 m).
A.5.2.2 The requirements in the full RVSM envelope are as follows:
1. At the point in the full RVSM envelope where ASEmean reaches its largest absolute value, the absolute value should not exceed 120 ft (37 m).
2. At the point in the full RVSM envelope where ASEmean plus ASE3 SD reaches its largest absolute value, the absolute value should not exceed 245 ft (75 m).
3. If necessary, for the purpose of achieving RVSM approval for an aircraft Group, an operating restriction may be established to restrict aircraft from conducting RVSM operations in areas of the full RVSM envelope where the absolute value of ASEmean exceeds 120 ft (37 m) and/or the absolute value of ASEmean plus ASE3 SD exceed 245 ft (75 m). When such a restriction is established, identify it in the data package and document it in appropriate aircraft operating manuals; however, visual or aural warning/indication systems should not be required to be installed on the aircraft.
A.5.2.3 Aircraft types for which application for type certification or major change in type design is made after April 9, 1997, should meet the criteria established for the basic envelope in the full RVSM envelope. The FAA will consider factors providing an equivalent level of safety in the application of this criteria as stated in part 21, § 21.21b(1).
A.6.2 Single Autopilot Installation. Paragraph A.4.1.1.7 states the air… › A.6.2 Single Autopilot Installation. Paragraph A.4.1.1.7 states the air…
A.5.3 Non-Group Approval.
A.5.3.1 The standards of paragraphs A.5.2.1, A.5.2.2 and A.5.2.3, cannot be applied to Non-Group aircraft approval because there can be no Group data with which to develop airframe-to-airframe variability. Therefore, a single ASE value has been established that controls the simple sum of the ASEs. In order to control the overall population distribution, this limit has been set at a value less than that for Group approval.
A.5.3.2 The standard for aircraft submitted for approval as Non-Group aircraft, as defined in paragraph A.3.2 of this Appendix, is as follows:
1. For all conditions in the basic RVSM envelope:
( ) m 50 ft 160 avionics case worst SSE sidual Re ≤ +
2. For all conditions in the full RVSM envelope:
( ) m 60 ft 200 avionics case worst SSE sidual Re ≤ +
3. Worst-case avionics means that combination of tolerance values, specified by the manufacturer for the altimetry fit into the aircraft, which gives the largest combined absolute value of avionics errors. For most systems, this may not be a fixed value over time.
A.5.3.3 An operating restriction may be established to restrict the Non-Group aircraft from conducting RVSM operations in areas of the full RVSM envelope where the requirements of paragraph A.5.3.2 cannot be met.
A.5.3.4 The ASE airworthiness standards in Appendix A, sections A.5.2 and A.5.3 should not be confused with the ASE values stated in the height keeping section 5.3. Appendix A sections A.5.2 and A.5.3 represent the ASE performance specification for RVSM airframe airworthiness certification, and is a key element of the RVSM airplane airworthiness certification process. Section 5.3 presents performance criteria specified for the RVSM height monitoring program, which is an element of the operational quality assurance process. The monitoring program is independent of the airworthiness certification program.
A.6 Aircraft System Configurations: Older “Legacy” Airframes.
A.6.1 Background. This paragraph provides additional guidance regarding configurations found
on older model airplanes (also known as “legacy” airplanes, e.g., B707, DC-8, older business jet, and turboprop aircraft, etc.) for which RVSM approval is sought.
A.6.2 Single Autopilot Installation. Paragraph A.4.1.1.7 states the air data system should
provide reference signals for automatic control and alerting at selected altitude. These signals should preferably be derived from an altitude measurement system meeting the
A.6.2.4 Independent Source for Altitude Hold Input to the autopilot. › A.6.2.4 Independent Source for Altitude Hold Input to the autopilot.
full requirements of this Appendix. In addition, paragraph A.4.1.1.7 states the altimetry system must provide an output which can be used by an automatic altitude control system to control the aircraft at a commanded altitude. The output may be used either directly or combined with other sensor signals. The altitude control output may be an altitude deviation signal, relative to the selected altitude, or a suitable absolute altitude output.
A.6.2.1 A distinction can be made between signals derived from an ADC and signals derived from an altitude measurement system. Paragraph A.4.1.1.7 does not mandate the need for dual ADC inputs to the automatic altitude control system.
A.6.2.2 Several airplane model types are equipped with a single autopilot installation. In many cases, the autopilot is only capable of receiving altitude hold inputs from a single source. It has been further noted retrofitting of these autopilot installations to receive altitude hold input from additional sources (e.g., another ADC) may yield one or more of the following problems:
1. The retrofit costs are a significant percentage of the total worth of the airframe.
2. The retrofit is not possible without replacement of the autopilot.
3. The retrofit increases air data system complexity, which in turn increases the scenarios and rates of failure.
4. Upgraded avionics (i.e., ADCs) are not available, or the vendors will not support retrofits.
A.6.2.3 There are two common avionics configurations that may meet RVSM requirements, but do not have dual ADC input to the autopilot. A general description and possible means of compliance are given below. They are:
1. Figure A.6-1, Example of Air Data System/Autopilot Configuration.
2. Figure A.6-2, Single Air Data Computer Configuration for Autopilot Input.
A.6.2.4 Independent Source for Altitude Hold Input to the autopilot.
A.6.2.5 Single ADC Input to the Autopilot. On a large number of older… › A.6.2.5 Single ADC Input to the Autopilot. On a large number of older…
Figure A.6-1. Example of Air Data System/Autopilot Configuration
1. The air data sensor (ADS) is a single LRU activated in altitude hold mode when the pilot presses an ALT HOLD button, after reaching the desired cruise FL. It is not tied to either ADC or other component comprising the air data system. The ADS provides ∆H information to the autopilot so the airplane can maintain the desired altitude. In some configurations, the pilot further provides FL information to the autopilot by manually selecting the displayed altitude (either pilot’s or copilot’s).
2. Airplanes equipped with the avionics configuration shown in Figure A.6-1 may show compliance as follows:
• The airplane must maintain altitude to within ±65 ft of the acquired altitude as required by paragraph A.4.1.4.1. For RVSM compliance, the ∆H signal must be accurate enough such that the airplane maintains the required ±65 ft altitude deviation specification. This may be substantiated with flight test data and/or manufacturer’s specification data.
• The altitude alerter should function if the ADS/ADC fails. If the altitude alert function is not operational, altitude hold performance must be monitored manually.
• The ADS should be compensated such that an airspeed change at a cruise FL is not interpreted by the system as change in altitude, causing altitude hold deviation in excess of ±65 ft.
• The altimetry systems meet the RVSM accuracy requirements specified in paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, as appropriate.
• All other requirements set forth in this advisory circular (AC), as appropriate, are satisfied.
A.6.2.5 Single ADC Input to the Autopilot. On a large number of older airplane models, the avionics configuration is such that one ADC provides altitude hold information to the autopilot (Figure A.6-2). In most models, a second ADC is also present, or provisions exist so a second can be installed.
autopilot
Cross-coupled
static sources
Cross-coupled
static sources
Alt Alt
ADS
1800 1800
ADC 2 ADC 1
A.7.1.1 Where precision flight calibrations are used to quantify or… › A.7.1.1 Where precision flight calibrations are used to quantify or…
Figure A.6-2. Single Air Data Computer Configuration for Autopilot Input
1. Airplanes equipped with the avionics configuration shown in Figure A.6-2 may show compliance as follows:
• The airplane must maintain altitude to within ±65 ft of the acquired altitude required by paragraph A.4.1.4.1. This may be substantiated with flight test data or manufacturer’s specification data.
• The altitude alerter should function if either air data system or ADC fails. If the altitude alert function is not operational, altitude hold performance must be monitored manually.
• If ADC1 fails, the airplane must be controlled manually until ATC contingency procedures are executed. Annunciation should be provided if the pilot deviates ±300 ft from desired altitude. This annunciation must be provided automatically by the altitude alert system. If the altitude alert system is not functioning, altitude hold performance must be monitored manually.
• The altimetry systems meet the RVSM accuracy requirements specified in paragraphs A.5.2.1 and A.5.2.2, or A.5.3.2, as appropriate.
• All other requirements in this AC, as appropriate, are satisfied.
A.6.3 Operational Restrictions. Applicants should be aware operational restrictions and/or
changes may also be required for aircraft with avionics configurations shown in Figures A.6-1 and A.6-2, to meet all RVSM requirements.
A.7 Altimetry System Performance Substantiation.
A.7.1 Flight Testing: Group and Non-Group Aircraft.
A.7.1.1 Where precision flight calibrations are used to quantify or verify altimetry system performance they may be accomplished by any of the following methods. Flight calibrations should only be performed once appropriate ground checks have been completed, and the certifying authority should agree to the number of flight test conditions. Uncertainties in application of the method must be assessed and taken into account in the data package.
autopilot
Cross-coupled
static sources
Cross-coupled
static sources
Alt 1 Alt 2
ADC 2
1800 1800
ADC 1
A.7.2.1.4 Effect of flight operating condition on SSE.
1. Precision tracking radar in conjunction with pressure calibration of the atmosphere at test altitude.
2. Trailing cone.
3. Pacer aircraft. The pacer aircraft must have been directly calibrated to a known standard. It is not acceptable to calibrate a pacer aircraft by another pacer aircraft.
4. Any other method acceptable to the FAA or approving authority.
Note: Data acquired using elements from the RVSM monitoring program, such as a ground-based height monitoring unit (HMU) or Aircraft Geometric Height Measurement Element (AGHME), or a portable Global Positioning System (GPS)-based monitoring unit (GMU), is not acceptable for substantiating the ASE performance specified in paragraphs A.5.2 and A.5.3.
A.7.1.2 ASE will generally vary with flight condition. The data package should provide coverage of the RVSM envelope sufficient to define the largest errors in the basic and full RVSM envelopes. Note in the case of Group approval the worst flight condition may be different for each of the requirements of paragraphs A.5.2.1 and A.5.2.2, and each should be evaluated. Similarly, for Non-Group approval, the worst flight condition may be different for each of the requirements of paragraph A.5.3.2 and each should be evaluated.
A.7.2 Altimetry System Error (ASE) Variability.
A.7.2.1 In order to evaluate a system against the ASE performance statements established by the Review of the General Concept of Separation Panel (RGCSP) (see Appendix D), it is necessary to quantify the mean and three standard deviation (SD) values for ASE, expressed as ASEmean and ASE3 SD. In order to do this, it is necessary to account for the different ways in which variations in ASE can arise. The factors affecting ASE are as follows and should be considered in the ASE evaluation:
A.7.2.1.1 Unit to unit variability of avionics.
A.7.2.1.2 Effect of environmental operating conditions on avionics.
A.7.2.1.3 Effect of transducer and/or avionics component error drift over time.
A.7.2.1.4 Effect of flight operating condition on SSE.
A.7.2.1.5 Airframe to airframe variability of SSE, including the following:
A.8.2.1 General. Figure A.8-1, Altimetry System Error and its… › A.8.2.1 General. Figure A.8-1, Altimetry System Error and its…
• Skin waviness, skin splices/joints, access panels, radome fit/fair.
• Pitot-static probe variation. This includes manufacturing variation, installation variation, and probe degradation (erosion/corrosion) over time.
• Static port variation (for aircraft configured with static sources flush to the skin surface). Sources of variation include port step-height, degradation, and static port condition.
• SmartProbes© (integrated ADC/pitot-static probe). Smart probes are sensitive to installation variation. They are also capable of complex SSEC algorithms that are a function of several variables, all of which may be affected by probe condition and installation.
A.7.2.2 Assessment of ASE, whether based on measured or predicted data, must include the factors listed above in paragraphs A.7.2.1.1 through A.7.2.1.5. The effect of item A.7.2.1.4 as a variable can be eliminated by evaluating ASE at the most adverse flight condition in an RVSM flight envelope.
A.7.2.3 This document does not specify separate limits for the various error sources contributing to the mean and variable components of ASE as long as the overall ASE accuracy requirements of paragraphs A.5.2 or A.5.3 are met. For example, in the case of Group approval, the smaller the mean of the Group and the more stringent the avionics standard, the larger the available allowance for SSE variations. In all cases, present the trade-off adopted in the data package in the form of an error budget including all significant error sources.
A.8 Altimetry System Component Error Budget.
A.8.1 General. The ASE budget demonstrates the allocation of tolerances among the various
parts of the altimetry system is, for the particular data package, consistent with the overall statistical ASE requirements. These individual tolerances within the ASE budget represent the maximum error levels for each of the air data system components contributing to ASE. These error levels form the basis of the maintenance procedures used to substantiate the RVSM airworthiness compliance status of Group or Non-Group aircraft. The component error evaluation should be assessed at the worst flight condition in the basic and full envelope.
A.8.2 Altimetry System Error (ASE) Components.
A.8.2.1 General. Figure A.8-1, Altimetry System Error and its Components, shows the breakdown of total ASE into its main components, with each error block representing the error associated with one of the functions needed to generate a display of pressure altitude. This breakdown encompasses all ASEs that can
A.8.2.1.5 “Perfect SSEC” would be that correction which compensated…
occur, although different system architectures may combine the components in slightly different ways.
A.8.2.1.1 The “Actual Altitude” is the pressure altitude corresponding to the undisturbed ambient pressure.
A.8.2.1.2 “SSE” is the difference between the undisturbed ambient pressure and the pressure within the static port at the input end of the static pressure line.
A.8.2.1.3 “Static Line Error” is any difference in pressure along the length of the line.
A.8.2.1.4 “Pressure Measurement and Conversion Error” is the error associated with the processes of transducing the pneumatic input seen by the avionics and converting the resulting pressure signal into altitude. As drawn, Figure A.8-1 represents a self-sensing altimeter system in which the pressure measurement and altitude conversion functions would not normally be separable. In an ADC system, the two functions would be separate and SSEC would probably then be applied before pressure altitude (Hp) was calculated.
A.8.2.1.5 “Perfect SSEC” would be that correction which compensated exactly for the SSE actually present at any time. If such a correction could be applied, then the resulting value of Hp calculated by the system would differ from the actual altitude only by the static line error plus the pressure measurement and conversion error. In general, this cannot be achieved, so although the “Actual SSEC” can be expected to reduce the effect of SSE, it will do so imperfectly.
A.8.2.1.7 Between Hp and displayed altitude occur the baro-correction…
Figure A.8-1. Altimetry System Error and Its Components
A.8.2.1.6 “Residual SSE” is applicable only in systems applying an avionic SSEC. It is the difference between the SSE and the correction actually applied. The corrected value of Hp will therefore differ from actual pressure altitude by the sum of static line error, pressure measurement and conversion error, and residual SSE.
A.8.2.1.7 Between Hp and displayed altitude occur the baro-correction error and the display error. Figure A.8-1 represents their sequence for a self-sensing altimeter system. ADC systems can implement baro-correction in a number of ways that would modify slightly this part of the block diagram, but the errors would still be associated with either the baro-correction function or the display function. The only exception is those systems that can be switched to operate the display directly from the Hp signal. These systems can eliminate baro-correction error where standard ground pressure setting is used, as in RVSM operations.
Continue reading ↓ 120 of 189 passages shown