AC 61-137 Approval of Manufacturers Required Training Programs
This document is cancelled. It may have been replaced. Check the official source before relying on it.
4. BACKGROUND. › Operating Limitations.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Approval of Manufacturer’s Required
Training Programs
Date: 9/26/08
Initiated by: AFS-800
AC No: 61-137
Change:
1. PURPOSE. This advisory circular (AC) provides information to organizations providing training in aircraft that contain a training requirement in the limitations section of the Aircraft Flight Manual (Airplane Flight Manual (AFM), Rotorcraft Flight Manual (RFM), etc.).
2. RELATED FEDERAL AVIATION ADMINISTRATION (FAA) GUIDANCE.
a. FAA Practical Test Standards (PTS).
b. Flight Standardization Board (FSB) Report. The FSB report for the specific aircraft, if available, is at http://www.opspecs.com/AFSData/FSBRs/Final/.
c. Limitations Section of the AFM.
d. FAA/Industry Training Standards (FITS). The FITS is available at http://www.faa.gov/education_research/ training/fits/.
3. AUDIENCE. The primary audience of this AC is training providers intending to offer training required by the specific Aircraft Flight Manual.
4. BACKGROUND.
a. Approval Process. This AC contains background information on the processes for granting approval, when required, of an aircraft training program in accordance with (IAW) the limitations section of the AFM/RFM, except for the supervised operating experience requirements of Title 14 of the Code of Federal Regulations (14 CFR) part 61, § 61.63(e) and (f). As noted in § 61.63(e) and (f), if a pilot is required to perform “X” hour(s) of supervised operating experience as pilot in command (PIC) under the supervision of a qualified and current PIC, a restriction will be added to the individual’s certificate. This restriction may be removed by the Administrator by providing adequate evidence of satisfying the requirements of the restriction. The appendix of this AC provides the technical training information that will meet the training requirements of specific aircraft.
b. Operating Limitations. Title 14 CFR part 91, § 91.9(a) states in part that no person may operate a civil aircraft without complying with the operating limitations specified in the approved AFM or RFM. Some aircraft manufacturers have begun requiring stringent training programs via an Aircraft Flight Manual limitation. For example, the limitation section of the Eclipse Aviation Corporation’s EA-500 AFM contains the following requirement: “All pilots
5. APPROVAL PROCESS. › a. Phase 1 - Initiation. The training provider should contact the FAA…
AC 61-137 9/26/08
operating the Eclipse EA-500 must be trained and qualified in accordance with the FAA- Accepted/Approved Eclipse Aviation Training Program or equivalent FAA-accepted/approved training program.” The type certification data sheet (TCDS) contains a similar limitation in the notes. Coordination of this AFM limitation included the General Aviation and Commercial Division (AFS-800), the Kansas City Aircraft Evaluation Group (MKC-AEG), and the FSB. This AFM limitation requires that all pilots operating the EA-500 must complete training in accordance with an FAA-accepted/approved program. Other manufacturers may consider placing a similar training requirement in the limitations section of their Aircraft Flight Manual. Traditionally, the manufacturer provides training to the first purchaser of their aircraft. Pilots of resale aircraft and third party training providers may not fall under the manufacturer sales contract, and, therefore, the Aircraft Flight Manual limitation is a means by which all operators of these aircraft receive training at least equivalent to the manufacturer’s. Consequently, the FAA now approves part 61 training programs for aircraft that have this kind of limitation. The FAA already approves training programs conducted under 14 CFR parts 141, 142, 135, 121, and 91 subpart K (part 91K).
c. Approval Authority. Currently, AFS-800 is reviewing and, if acceptable in accordance with this AC, approving all part 61 training programs that require FAA approval (other than those associated with a part 142 certificated training center). Future changes in approval authority will be outlined in inspector guidance.
5. APPROVAL PROCESS. The general process of approval is an orderly method used by Flight Standards Service (AFS) inspectors to ensure that the training program meets regulatory standards and provides for safe operating practices. It is a modular, generic process that applies to many types of approvals. The process consists of five distinct, yet related, phases and can result in approving or disapproving the training providers program. It is important to understand that the process described in this section may not be all inclusive, but rather a guide to make this process smooth and efficient. The five phases are:
• Initiation, • Formal proposal/request, • FAA detailed analysis, • Training provider’s demonstration, and • Approval.
a. Phase 1 - Initiation. The training provider should contact the FAA office that has jurisdiction over their training program to inform them of his or her plan to provide required training. During initial inquiries, it is important for the FAA and the operator to become familiar with the subject matter. The inspector then takes the following actions:
• d approval requirements, Becomes thoroughly familiar with existing FAA policy an • Becomes familiar with the appropriate technical material, e of the proposal, • Accurately assesses the character and scop • Determines if it requires a demonstration, • Determines the need for any coordination requirements, and
Page 2 Par 4
c. Phase 3 - FAA Detailed Analysis. › (1) In this phase the inspector conducts a detailed analysis, review,…
9/26/08 AC 61-137
• Ensures the operator has a clear understanding of the minimum requ constituting an acceptable submission.
NOTE: It is essential in this phase for the operator to have a clear
irements
understanding that, although the inspector may provide advice and guidance
nsibility of the training provider.
b.
clearly defined, and that the documentation specified in phase one is provided. The required information must be
. ufficient detail to assess the completeness of the required information. If the operator’s proposal is not complete, or the quality
e on is unacceptable, and returns the submission. If all parties are able to reach agreement, on measures to correct omissions or deficiencies, the inspector will determine if the submission is a p inspector informs the operator and phase three begins.
training program. The analysis may take place entirely within at the FAA approving office, at the site of oper focuses on the form, content, and technical quality of the training program to determine:
• rary to any applicable 14 CFR,
documents,
• It provides for safe operating practices,
to the training provider, the development of the final training program submitted to the FAA is solely the respo
Phase 2 - Formal Proposal/Request. This phase begins when the training provider formally submits a proposal for FAA evaluation.
(1) In this phase, the inspector first reviews the proposal to ensure that it is
complete and detailed enough to permit a thorough evaluation of the operator’s capability and competence in providing the required equivalent level of training.
(2) This phase does not include a detailed and technical analysis of the training program However, in this phase the inspector examines the training program in s
is obviously unacceptable, the inspector immediately returns it, with an explanation of the deficiencies, before conducting any further review and evaluation.
(3) Normally, unacceptable submissions are returned with a written explanation of the reasons for their return. In complex cases, the inspector may request a meeting with the training provider to resolve issues and agree on a mutually acceptable solution. If mutual agreements cannot be reached, the inspector terminates the meeting, informs the training provider that th submissi
cce table. If it is deemed acceptable, the
c. Phase 3 - FAA Detailed Analysis.
(1) In this phase the inspector conducts a detailed analysis, review, and evaluation of the
ations, or at both facilities. The detailed analysis
It is not cont
• It is not contrary to the direction provided in this AC or other safety-related
Par 5 Page 3
5. APPROVAL PROCESS. › The appropriate specifications (operations specifications (OpSpecs),…
AC 61-137 9/26/08
• It will meet the required equivalent level of training,
• The training provider has the capability and competence to safely conduct the training, and
• The training provider has the processes and procedures to oversee and manage the training.
(2) The FAA must address any deficiencies in the training program before proceeding to the next phase. A discussion with the training provider may adequately resolve certain discrepancies or questions, or assist in obtaining additional information. We may need to return certain sections of the submission to the operator for specific changes. However, if the inspector determines that the material is grossly deficient or unacceptable, he or she will return the entire program to the training provider with an appropriate explanation and immediately terminate this phase. If the results of the evaluation are acceptable and a demonstration requirement exists, the inspector should issue the training provider provisional approval before continuing with the approval process.
d. Phase 4 - Training Provider’s Demonstration. In this phase the inspector inspects the training provider’s facilities and equipment, and observes personnel in the performance of their duties. The observation includes factors such as participants (instructors and students), training criteria, effectiveness of training, and sequence of events.
(1) During these demonstrations, it is normal for minor discrepancies to occur. These discrepancies can often be resolved by obtaining commitments from the training provider to make appropriate changes.
(2) The inspector will stop the demonstration in this phase when gross deficiencies or unacceptable levels of performance are observed. The inspector will identify what is required of the training provider so that final approval can be issued.
(3) If the training provider is unwilling or unable to make the identified changes, the inspector will terminate the process entirely and the provisional approval will be canceled. If this happens and the training provider still wishes to seek approval, the training provider may need to reenter the approval process at phase two (that is, submit a new formal proposal/request).
e. Phase 5 - Approval. An approval will be issued if the inspector finds the demonstration satisfactory. If it is not approved, notification is sent to the training provider in Phase 3 or 4. The appropriate specifications (operations specifications (OpSpecs), management specifications (MSpecs), training specifications, etc.) paragraph normally issues the approval. ORIGINAL SIGNED BY John Allen for James J. Ballough Director, Flight Standards Service
Page 4 Par 5
2. ECLIPSE 500 TYPE RATING TRAINING PREREQUISITES. › c. Jet Basics Knowledge. Internet, CD, DVD, or other self-learning…
APPENDIX 1. TRAINING REQUIREMENTS FOR THE ECLIPSE AVIATION
CORPORATION EA-500
1. TRAINING. Pilots operating the Eclipse Aviation Corporation EA-500 must complete the following training modules:
• Pre-type rating training, • Emergency situation training, • Flight skills assessment, • EA-500 type rating training, • Mentorship, and • Recurrent training.
a. Training Modules. Training objectives for each of these modules are described below. Some pilots may be exempted from some of these training requirements. Within the description of each module (below) contains a note that explains who can be exempted from the module (or portion of it) and under what conditions. Exemptions are not automatic; the training provider will evaluate each individual on a case-by-case basis. Ultimate authority for allowing the exemption lies with the flight training manager or equivalent. Though it is not required that the pre-type rating training, flight skills assessment, and emergency situation training be completed in that order, these three modules must be successfully completed prior to starting the type rating training module. Mentorship and recurrent training will take place after successful completion of the type rating training module.
b. Training Providers. The training providers are not required to implement every particular aspect of the Eclipse Aviation Corporation training program. However, the training must meet an equivalency. For example, the Eclipse Aviation Corporation uses an aerobatic L-39 Albatross aircraft to conduct prerequisite upset recovery training. Though a third party training provider is not required to use an L-39, the training objectives, flight concepts, flight techniques, and demonstration of maneuvers/tasks must be equivalent and must be trained and completed.
2. ECLIPSE 500 TYPE RATING TRAINING PREREQUISITES. Prior to beginning the actual type rating training, the pilot must meet or complete certain prerequisites. Those prerequisites are as follows:
a. Certificate Requirements. The pilot must hold the following certificates and ratings:
(1) Private Pilot – Airplane Multiengine Land and Instrument Airplane. The instrument rating must include multiengine privileges.
(2) Medical Certificate. Current and valid third class medical certificate.
b. Currency. The pilot must be current under Title 14 of the Code of Federal Regulations (14 CFR) part 61, § 61.57(c) and (d).
c. Jet Basics Knowledge. Internet, CD, DVD, or other self-learning training on the following subjects should be completed prior to arriving for type rating training. When the pilot
b. Upset Recovery Training. › (1) Flight Concepts.
arrives for training, a knowledge test must be conducted to ensure that the pilot has the requisi knowledge to begin type rating training in the EA-500. All deficiencies in knowledge will be
te
addressed in ground school. At a minimum, the following subjects should be taught in this phase:
(1) Jet engines,
(2) High altitude physiology,
(3) High altitude and high-speed aerodynamics,
(4) High altitude flight planning, and
(5) High altitude weather and weather radar.
pleted within 6 months of starting type rating flight and ground training.
itation and has logged at least 25 hours PIC time in a turbojet airplane.
3. EMERGENCY SITUATION TRAINING.
a. Ground Training.
(1) Aviation Physiology.
ickness,
ration, and
(2)
xia Training.
b. ing.
(1)
NOTE: This training should be com
NOTE: The pilot may be exempt from Jet Basics if he/she already holds a turbojet type rating without a pilot-in-command (PIC) lim
• Hypoxia, • Hyperventilation, • Decompression s • Gas expansion, • Circadian rhythm, • Fatigue and sleep, • n, Self medicatio • Eating and hyd • Night vision.
Rollover Trainer.
• Exposure to negative g forces • Pitch orientation and control, and ,
• Roll orientation and control.
(3) Reduced Oxygen/Hypo
Upset Recovery Train
Flight Concepts.
• Orientation of lift vector through roll attitude,
le of attack,
forces, and ring pitch changes.
(2)
gree of roll,
b. Upset Recovery Training. › (3) Demonstrations, Tasks, or Maneuvers.
Note that 14 CFR part 91, §§ 91.303 and 91.307 may ht training.
ked turns,
• ion,
entries).
nt y authorization or is a current armed forces pilot
e
set recovery training. Upset recovery training must be conducted in an aircraft certificated for all maneuvers required in the training (aerobatic).
• Earth centered attitude awareness, • Distinction between aircraft attitude and ang • Altitude required for vertical maneuvering, • Recognition and control of cockpit g • Thrust control du
Flight Techniques.
Lift vector orientation and control past 90 de • • Lift vector magnitude control, flight path control, • Use of more than 1g for • Use of less than 1g for flight path control, • Ballistic (0g) flight, and • Ability to maintain -1g (inverted) flight for flight path control.
(3) Demonstrations, Tasks, or Maneuvers.
apply to upset recovery flig
• 60 degree ban • Wingover, • 0g pushover, • Aileron roll, • Roll reversal, • Barrel roll, • Half cuban 8, • Inverted flight, • Pitch mis-trim, • Mountain wave encounter, Wake vortex encounter, and • Insidious upset encounter (replicates the situation resulting from inattent distraction, a “soft,” unannunciated autopilot (AP) failure, or other subtle
NOTE: The pilot may be exempt from either or both components (ground training and upset recovery training) of emergency situation training if the pilot presents evidence of recent completion of equivalent training. For the physiology module, equivalent training includes FAA, armed forces, air carrier, or other recognized programs with equivalent course content. For the upset recovery training, the pilot may be exempt if he/she holds a curre FAA Aerobatic Competenc rated in fighter type aircraft. The pilot must furnish documentation to b eligible for the exemption.
NOTE: Eclipse Aviation Corporation uses an L-39 Albatross for up
c. Course Completion Standards. › (1) Provide the pilot with the knowledge and skills to successfully…
4. FLIGHT SKILLS ASSESSMENT. Flight skills assessment is done to ensure that the pilot has the basic instrument flight skills to enter type rating training. The minimum requirement for the flight skills assessment is that the pilot must successfully complete the equivalent of an instrument proficiency check (IPC). If the pilot fails to meet this minimum during the flight skills assessment then the pilot must successfully complete supplementary training and meet the IPC standard before beginning type rating training.
NOTE: The pilot may be exempt from the flight skills assessment if he or she meets the aeronautical experience requirements for an airline transport pilot certificate as specified by part 61, § 61.159(a) and meets the following instrument currency requirements: instrument flight time last 90 days-five hours; instrument approaches last 90 days-10; and instrument evaluation (instrument proficiency check or instrument rating practical test) passed within the last six months prior to entering type rating course.
5. INITIAL TYPE RATING TRAINING CURRICULUM. The type rating training course is the core of the training program. It is intended not only to train the pilot to pass the Airline Transport Pilot and Aircraft Type Rating Practical Test Standards for Airplane (FAA-S-8081-5, as amended), but also train the pilot (for single pilot operations) in single pilot resource management. This includes training in risk management, automation management, situational awareness, and controlled flight into terrain (CFIT) awareness.
NOTE: Ground training, systems integration training, and flight training can be integrated for training efficiency.
a. Minimum Course Length-Flight. Flight time in this section includes FAA-approved simulator and approved flight training device (FTD) time.
(1) Sixteen hours of flight time.
(2) Seven lessons (each of which takes one or more flights to complete).
b. Minimum Course Length/Ground. There is no minimum number of ground training hours, since it is unclear as to how many hours will be credited for the pre-type rating prerequisite systems training (Web-based, computer-based training (CBT), etc.) and how much additional systems training will be required when the pilot arrives for type rating training. The principal operations inspector (POI) will need to determine if the prerequisite training is comprehensive enough to eliminate any of the ground training areas listed below. The training provider must have a system in place that tests the pilot’s knowledge in the learning areas to ensure that the pilot has all the requisite knowledge. Finally, all special emphasis items must be taught in ground school, regardless of whether it was covered in the pre-type rating training or not.
c. Course Completion Standards.
(1) Provide the pilot with the knowledge and skills to successfully pass the FAA Type Rating Practical Test, and
(1) Ground Training Content. › (a) Single Pilot Resource Management (SRM).
(2) Provide the pilot with the skills needed to operate the EA-500 with the highest degree of safety in foreseeable operating environments.
d. Scenario Evaluation/Learner Centered Grading. The Eclipse Aviation Corporation designed their training program under the FAA/Industry Training Standards (FITS) methodology. This methodology uses scenario based training and learner centered grading to train and enhance the high order thinking skills (single pilot resource management, risk management, automation management, CFIT awareness, and situational awareness) needed to safely operate the EA-500 as a single pilot. Although FITS acceptance is not required to conduct EA-500 training (at a minimum, FAA approval is required), FITS methodology has been shown to be effective in the development of higher order thinking skills. If a training provider requests FITS acceptance along with FAA approval, the POI will evaluate the curriculum to insure that it meets the FITS acceptance requirements. Detailed information on how to apply FITS methodology can be found on the FITS Web site at http://www.faa.gov/education_ research/training/fits/. Guidance on FITS acceptance can be found in FAA Order 8900.1, Volume 5, Airman Certification, Chapter 9, Other Airmen Authorizations, Section 5, Issue an FAA Industry Training Standards (FITS) Acceptance When Requested by a Flight School, Training Center, or Other Training Provider.
e. Course Content.
(1) Ground Training Content. The following list of subjects must be included in the ground training content of the initial type rating training curriculum.
(a) Single Pilot Resource Management (SRM). The first objective of this training section is to provide the pilot with knowledge of SRM basic elements and the understanding of the importance of SRM in single pilot EA-500 operation. The second objective is to provide the EA-500 pilot with the knowledge, skills, procedures, and tools needed to identify single pilot work load drivers and manage that work load within the resources available. The following are sub-elements of SRM:
• Basic SRM elements; o SRM definition and concepts, and o Application of SRM.
• Single pilot workload drivers; o Key factors creating workload, and o Managing workload.
• Maintaining Situational Awareness (SA); o Definition and concept of SA, o Automation management, and o Maintaining SA in the EA-500.
• Using available resources; and o
Managing resources, and Resource categories for SRM, o
(1) Ground Training Content. › (c) Personal minimums.
o Using SRM in the EA-500.
• o The students will accurately describe the basic elements of SRM, and
pply risk management principles to the operation of the EA-500 in the high airspeed air traffic control (ATC) and high altitude physiological e ing simple risk assessment tools.
•
s, Risk severity and likelihood, and
• Categories of risk, and
entification model (PAVE, IM-SAFE, etc.).
• Assessment of hazards and risks, and
• and
• m
e end
pilot mums and how they are used following completion of e iliarity with personal minima categories and
• ms;
• nal minimums, and
Completion standards.
o Explain their significance and application.
(b) Risk management. The objective of this section is to (1) develop the pilot’s knowledge of the three elements of risk management: risk identification, risk assessment, and risk mitigation and (2) to develop the pilot’s skill and ability to a
nvironments us
Overview; o System safety principles, o Hazards and risk o o Risk principles.
Risk identification; o o Use of a risk id
Risk assessment; o
Use of risk assess o ment matrix.
Risk mitigation; and o Categories of mitigation,
Use of a risk mitiga o tion model (TEAM, etc.).
pletion standards. Co o The students will accurately describe risk management elements at th
of each module of training, and o The students will accurately explain risk management concepts and
procedures at the end of the risk management training modules.
(c) Personal minimums. The objective of this section is to provide the EA-500 with (1) an understanding of the concept of personal mini
sup rvised operating experience, and (2) fam how they are used during flight planning.
Basic elements of personal minimu o Need for personal minimums, and o Personal minimums concepts.
Application of personal minimums; and o Categories of perso
(1) Ground Training Content. › (n) Electronic power distribution system.
o Application of personal minimums during the preflight planning process.
• o
minimums and explain how they are used during flight operations, and
ibe the basic elements of personal minimums and explain how they are used during flight operations.
(d) Airplane Flight Manual (AFM) review.
(e) Aircraft limitations.
(f) Aircraft performance, performance airspeeds, and flight profiles.
of minimum equipment list (MEL)/Master Minimum Equipment List (MMEL).
(i) Aircraft general description.
(j) Avio (Avio NG as appropriate) integrated avionics suite.
(k) Aircraft computer system.
(l) (AHRS) air data system.
• •
vionics as required by the ATP and Aircraft Type Rating PTS.
electronic control (FADEC) and Automatic Power Reserve
(n) bution system.
, interior and exterior lighting; • • •
o o Pilot controls for the electrical system.
Completion standard.
The student will accurately describe the basic elements of personal
o The student will accurately descr
(g) Weight and balance.
(h) Aircraft maintenance and use
Air data system and Attitude and Heading Reference System
• Aircraft Computer System (ACS) interfaces; • System overview; System operation; Normal, abnormal, and emergency operations; and • Completion standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems, components, and a
(m) Aircraft engines, full-authority digital
(APR).
Electronic power distri
• Electrical power distribution system ACS interfaces; System overview; System operation; o Electrical components,
Electrical buses and structure, and
(1) Ground Training Content. › (p) Multifunction displays (MFD) and controls.
• Normal, abnormal, and emergency operations; and Completion standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems, comp • onents, and avionics as required by the ATP and Aircraft Type Rating PTS.
iled ts, normal and abnormal operations as required by the ATP and Aircraft Type Rating PTS.
dicator (ADI);
• m igation, and Surveillance (CNS); and n,
•
required by the ATP and Aircraft
trols. The objective is to provide a detailed
al and abnormal operations as required by the ATP and Aircraft Type Rating PTS.
• c ; • n; ,
Fuel, and
• alerting;
(o) Primary flight displays (PFD) and controls. The objective is to provide a deta description of the EA-500 PFD, including componen
• PFD; • General; • ACS interfaces; Flight mode annunciator (FMA);
• • Airspeed tape; • Attitude-Direction In • Altitude tape; • Vertical speed tape; Nav Co munication, o Communicatio o Navigation, o Surveillance, o Horizontal situation indicator, and o Composite mode.
Completion standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 PFD including components, and normal and abnormal operations as Type Rating PTS.
(p) Multifunction displays (MFD) and con description of the EA-500 MFD, including components, and norm
• MFD; • General; • ACS interfaces; Ba kup ADI Systems informatio o Engine o Landing gear, o Flaps, o Pressurization, o o Flight controls.
Crew Alerting System (CAS) message/
(1) Ground Training Content. › (u) Auto flight system.
o Location, o Types of messages and definition,
Use of CAS knob, and
• d
l keys,
ance, Weight and balance, and
• eneral knowledge of the EA-500 PFD including components,
red by the ATP and Aircraft Type
f configuration protection.
(t) anical.
• • r nd
• onents,
(u) Auto flight system. The objective of this section is to provide a detailed description of the EA-500 Autoflight system as required by the ATP and Aircraft Type Rating PTS.
• ns,
o Hierarchy of messages, o Appearance, o o Alerting (AURALS).
MFD tile management; an o Line select key review, o Left right beze o Primary function keys, o Perform o o AFM.
Completion standards: To complete this subject area, the pilot will demonstrate g normal and abnormal operations as requi Rating PTS.
(q) CAS messaging system.
(r) System synoptic pages.
(s) Warning systems and takeof
Flight controls/mech
• Flight controls; • ACS interfaces; • System overview; System operation; No mal, abnormal, and emergency operations; a o Takeoff configuration protection, and o TO CONFIG OK and CONFIG Warnings.
Completion standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems, comp and avionics as required by the ATP and Aircraft Type Rating PTS.
Functions;
functio o Three axis AP
, o Pitch autotrim
o Flight director (FD), o Yaw damper, o o Speed protect
(1) Ground Training Content. › (w) Fuel system.
Stick pusher,
ion, and
• aces;
• r ces;
tem (FMS),
nd system (GPS).
• o faces;
•
To complete this subject area, the pilot will
owledge of the EA-500 Autoflight system as required ircraft Type Rating PTS.
(v) s.
• • n standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems, components,
quired by the ATP and Aircraft Type Rating PTS.
(w)
• • Normal, abnormal, and emergency operations; and
o Flight mode annunciation.
ACS interf
Ai craft interfa o Trim, o Flight management sys o Sidestick, o Air data computers,
AHRS and M o DI, a Global positioning o
Pil t inter o AP control panel,
Sidestick, and o
PFD. o
Modes of operation; and o Lateral, o Vertical, o Pilot assisting, and o Envelope protection.
• Completion standards: demonstrate general kn by the ATP and A
Landing gear and brake
• ACS interfaces; • System overview; System operation; Normal, abnormal, and emergency operations; and • Completio
and avionics as re
Fuel system.
• ACS interfaces; • System overview; System operation;
(1) Ground Training Content. › (cc) Fire protection system.
• Completion standards: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems, components,
ired by the ATP and Aircraft Type Rating PTS.
(x)
(y) Pre r
• ACS interfaces,
ndards: To complete this subject area, the pilot will
EA-500 aircraft systems, components, required by the ATP and Aircraft Type Rating PTS.
(z) A
(aa)
• • • al, and emergency operations; and
s: To complete this subject area, the pilot will knowledge of the EA-500 aircraft systems, avionics as required by the ATP and Aircraft Type Rating
(bb)
• • • al, abnormal, and emergency operations; and
s: To complete this subject area, the pilot will demonstrate general knowledge of the EA-500 aircraft systems,
avionics as required by the ATP and Aircraft Type Rating
(cc)
• • System overview;
and avionics as requ
Pneumatics.
ssu ization system.
Pressurization and climate control; and o o System overview, o System operation, and o Normal, abnormal, and emergency operations.
• Completion sta demonstrate general knowledge of the and avionics as
ir conditioning.
Oxygen system.
• ACS interfaces; • High altitude physiology review; System overview; System operation (special emphasis on donning of oxygen masks); Normal, abnorm • Completion standard demonstrate general components, and PTS.
Ice and rain protection.
• ACS interfaces; System overview; System operation; Norm • Completion standard
components, and PTS.
Fire protection system.
ACS interfaces;
(1) Ground Training Content. › (nn) Differences training from base EA 500 items.
• • al, and emergency operations; and
s: To complete this subject area, the pilot will al knowledge of the EA-500 aircraft systems, avionics as required by the ATP and Aircraft Type Rating
(RVSM) policies and procedures. The objective o ing of the RVSM policies and origin, proc ents.
a bus failures.
AWS).
(ll) D ME) systems.
(mm)
• ogy;
DEC, avionics system, and electronic power
es and data buses; ncy procedures, focusing on avionics and electronic
Stick pusher system;
(nn) Differences training from base EA-500 items.
• Weather Radar.
System operation; Normal, abnorm • Completion standard demonstrate gener components, and PTS.
(dd) Preflight procedures.
(ee) Normal procedures.
(ff) Reduced Vertical Separation Minimum f this section is to provide the pilot with an understand
edures for its use, and aircraft limitations and requirem
(gg) Abnormal and emergency procedures.
(hh) Generator, ACS, or flight bite dat
(ii) Terrain Awareness and Warning System (T
(jj) Traffic Advisory System (TAS).
(kk) Automatic direction finder (ADF) system.
istance measuring equipment (D
Special emphasis ground training items.
High altitude physiol • Donning of oxygen masks; • Single pilot resource management, risk assessment and risk management; CS, FA • Relationship of the A distribution system;
nic bus • Relationship of electro • Abnormal and emerge power distribution systems; • • Emergency gear system; and • Use of alternate trim.
• ETT Modification Differences; • Avio NG Avionics System Differences; and
(2) Systems Integration Training Cockpit Procedures Trainer… › (s) Completion standards.
(2) TD/Flight Simulator (SIM) or Aircraft. The following is a list of items that should be practiced/trained in a CPT, app
cial emphasis item per FSB report).
t).
report).
d (special emphasis item per FSB report).
ures.
eport).
).
(o) Abnormal and emergency procedures (special emphasis item per FSB report).
(p) Use of composite mode (special emphasis item per FSB report).
(q) (special emphasis item per FSB report).
(r)
AWS.
(s) Completion standards. The student will demonstrate knowledge of general
wledge of
Systems Integration Training Cockpit Procedures Trainer (CPT)/F
roved FTD, approved SIM, or in the EA-500 while on the ground:
(a) Cockpit orientation.
(b) PFD/MFD preflight setup (spe
(c) Cockpit checklist flow (special emphasis item per FSB report).
(d) Instrument approach tuning and setup (special emphasis item per FSB repor
(e) Avionics systems integration.
(f) Communication tuning and setup (special emphasis item per FSB
(g) Analysis of system synoptic pages (special emphasis item per FSB report).
(h) Use of keyboar
(i) CAS messaging system (special emphasis item per FSB report).
(j) Quick reference handbook (QRH) review, cockpit setup flows and proced
(k) AP overview.
(l) Setup of the AP control panel (special emphasis item per FSB report).
(m) PFD flight mode annunciations (special emphasis item per FSB r
(n) Programming of FMS, when installed (special emphasis item per FSB report
ACS, Air Data Computer (ADC), generator and flight bite data bus failures
Differences training from base EA-500 items.
• Avio NG Avionics System Differences; and • Operational Systems Operation including Weather Radar, TAS, and T
EA-500 cockpit components, including interior panels, switches, display locations, and functions, be able to complete a preflight inspection, demonstrate knowledge of EA-500 normal procedures and flows, demonstrate kno
(3) Flight Training Requirements. › 12. Icing considerations.
the appropriate use of the EA-500 QRH, and display basic knowledge of abnormal and emergency procedures.
(3) lessons should be scenario-based. It is understood that repetitive skills based training can and should be i
gement, aeronautical decision making, automation management, situational awareness, and CFIT awareness traini
operations in Class A, C, and D airspace is required. Flight training operations in Class B, E, and G is encouraged.
(d) Night flight is required in this program. If a mentor program is part of the training program, and night flight is a required part of mentor program, then a night flight is not required in the type rating training program. If the pilot is not subject to a mentor program, or if the mentor program ht flight, then night flight is required in the type rating trai
peed combinations (including steep turns, slow flight, ap onstration).
ht maneuvers required for EA-500 practical test.
operations.
es.
Flight Training Requirements. To meet the completion standards below, most flight
ncorporated into the flight lessons and/or scenarios. Single pilot resource management, risk mana
ng must be incorporated throughout the flight training. Learner centered grading should be incorporated into the entire training program.
(a) A minimum of 16 hours of flight time in seven or more flight lessons is required.
(b) FAA-approved simulators and/or FTDs may be used to accomplish the flight training requirements.
(c) Flight training
does not have a requirement for nig ning program.
1. Exterior preflight inspection.
2. Cockpit/cabin setup.
3. Aircraft systems tests and checks.
4. Before takeoff procedures.
5. Rejected takeoffs and landings.
6. Pitch attitude, power settings and airs proaches to stalls, and stick pusher dem
7. Maneuvering at best single-engine rate-of-climb speed (VYSE).
8. Basic and advanced flig
9. Jet aircraft traffic pattern
10. Departure and arrival procedur
11. Instrument approaches, missed approach procedures, and holding.
12. Icing considerations.
(3) Flight Training Requirements. › 35. Use of emergency gear system (special emphasis item per FSB report).
13. RVSM considerations.
erations.
e of oxygen.
moval.
25. Use of alternate trim.
cific avionics system emergencies.
report).
in composite mode (special emphasis item per FSB report).
30. Use of CAS messaging system (special emphasis item per FSB report).
31. High altitude single pilot operations (special emphasis item per FSB report).
32. Loss of all direct current (DC) power and effect on the aircraft and the FADEC system
er FSB report).
ial emphasis item per FSB report).
14. Engine shutdown and restart.
15. Single engine approach and landing.
16. Single engine missed approaches.
17. No flap takeoffs.
18. No flap/partial flap landings.
19. En route and high altitude op
20. Loss of pressurization and us
21. Emergency descents.
22. Abnormal and emergency procedures.
23. Smoke and fumes re
24. Unusual attitude recoveries.
26. Spe
27. Loss of MFD/PFD.
28. Use of PFD, MFD, and composite mode (special emphasis item per FSB
29. Instrument approaches with PFD/MFD
(special emphasis item per FSB report).
33. Other electrical system malfunctions (special emphasis item p
34. Donning of oxygen masks (spec
35. Use of emergency gear system (special emphasis item per FSB report).
36. Stick pusher system (special emphasis item per FSB report).
37.
38. Circling Approach Procedures.
39. Opt .
40. Completion standards.
the
6.
ogram is
d no
number of events under mentor sup i
6. MENTOR PROGRAM. › c. Assigned Profile. A pilot will not be considered as having completed…
t 61, § 61.63 apply.
vider
entor services provider will work closely together in developing men
ut reservation that the pilot is safe to operate consistently as a solo pilot in t
Use of alternate trim (special emphasis item per FSB report).
ional Systems Operations including Weather Radar, TAS, and TAWS
• Provide the pilot with the knowledge and skills to successfully pass FAA Type Rating Practical Test as amended, and
• Provide the pilot with the higher order skills needed to operate the EA-500 with the highest degree of safety and utility in foreseeable operating environments.
MENTOR PROGRAM. The mentoring program is for pilots with low flight time or experience in turbine-powered aircraft. It is intended to provide the pilot with additional experience, under the watchful eye of an experienced mentor. Additionally, a mentor pr designed for pilots who received their type rating in a traditional type rating program. If an applicant meets the experience requirement listed below (after successful completion of the type rating training program) prior to taking the practical test, then equivalency has been met an post-type rating training will be required.
a. Mentor Supervised Events. After successfully completing a traditional type rating training program, the pilot will be required to perform a
erv sion. The matrix below lists the minimum number of events for a specific pilot experience level. Events should be tailored to individual requirements, as dictated by the pilot’s typical operating profile. After an assessment of the pilot’s prior experience and level of performance during type training, they will be assigned an individualized profile that will prescribe a list of events and the number of times each event must be accomplished. There is no specific fixed number of flight hours required for a given pilot’s mentoring program, unless the minimum hour requirements of par
b. Mentor Program. Since a mentor program is part of initial training, the training pro oversees that program. It is expected that organizations providing only mentor services may be established and training providers may contract with these mentor service providers. In this case the training provider and the m
tor programs that are tailored to the pilot, considering the pilot’s experience and performance during the type rating training.
c. Assigned Profile. A pilot will not be considered as having completed the training provider’s EA-500 training program until he or she completes the assigned profile and the mentor is satisfied witho
he EA-500.
d. Required Mentoring Documentation. The training provider needs to document that th pilot has received the required mentoring. This documentation should include certification that the pilot has satisfactorily completed the assigned mentoring as listed in his or her mentor profile. The pilot should be issued a certificate or sign-off indicating that the required mentoring has been completed.
6. MENTOR PROGRAM. › e. Mentor Matrix/Profile. The matrix below will be used to identify a…
e
e. Mentor Matrix/Profile. The ma ow will b fy a pilot’s rofile based on previous flight experience ased in ty and as determined by the manager of fl ing, the pilo assigned an in profile. This profile will be provided to the pilot and mento itiating the g p pilot meets one portion of a higher experience level, but only a lower portion of another, the pilot must complete the m ogram of xperienced e as over 5,000 hours but only one type rating, then that pilot mu mplete th PERIENCE PILOT entor profile.
LOW EXPERIENCE
PILOT
MOD TE EXPERIENCE
PILOT
H EXPERIENCE
PILOT
trix bel . Subsequently, b
e used to identi
on performance
initial p pe rating training
dividual ight train t will be r prior to in ir mentorin rogram. If the
entoring pr the lower e pilot. For xample, if the pilot h st co e “MODERATE EX ” m
ERA IGH
Flight Time Under 1000 100 00 Over 5000 0-50 Type Ratings None Multiple One TASKS # of Tasks # of Tasks # of Tasks 1. Class A airspace 5-9 3-5 1-2 2. Class B airspace 3-5 2-3 1-2 3. Class C/D airspace 3-5 2-3 0-2 4. Class E/G airspace 3-5 2-3 1-2 5. Short runway operation 5-7 3-5 3-5 6. Approaches: precision 5-7 3-5 1-3 7. Approaches: non-precision 5-7 3-5 1-3 8. Circling approaches 5-7 3-5 1-3 9. Missed approaches 5-7 3-5 1-3 10. Landings 15-20 10-15 5-10 11. Maximum range flight 2-3 1-2 0-1 12. Actual instrument ions
3-5 2-3 1-2 meteorological condit (IMC) flights 13. Flight above flight level
2-3 1-2 0-1 (FL) 350 14. Total full mission scenarios
3-7 2-3 1-2
15. Autof integration
5-7 3-5 1-3 light and systems
16. Night operations 2-3 2-3 1-2 17. Special operations Varies Varies Varies
(1) Event Categories and Specific Events. › 1. Fly to an unfamiliar airport.
(1) Eve ic/expanded events that must be accomplished within each event category. They are not all-inclusive and the mentor and/or pilot ma
(a) Class A airspace:
1. Perform flight in RVSM airspace and exhibit adequate knowledge of airspace requirements.
5. Compute/update fuel requirements during flight and discuss implications.
6. Exhibit adequate knowledge of diversion requirements and planning.
terminal area (descent point and rate); discuss implications and techniques of late descent (ATC, planning error, etc.).
8. Monitor pressurization for proper scheduling; exhibit adequate knowledge of pressurization system.
9. Obtain destination and potential diversion and alternate weather using proper procedures.
(b)
.
and departure with no preventable missed radio calls.
P).
val and terminal airspeed requirements and restrictions.
nt Categories and Specific Events. The following are specif
y add an event if it will enhance the overall experience.
2. Exhibit adequate knowledge of using high-altitude charts.
3. Select optimum cruise flight level and exhibit adequate knowledge of speed vs. range performance.
4. Compute fuel requirements at planned FL and ± 2,000 feet of planned FL.
7. Plan descent to
Class B airspace:
1. Fly a Standard Terminal Arrival Route (STAR) to an airport in Class B airspace.
2. Fly an instrument approach to an airport in Class B airspace
3. Perform an arrival
4. Fly a departure procedure (D
5. Exhibit adequate knowledge of arri
6. Exhibit adequate knowledge of charted visual approaches.
(c) Class C/D airspace:
1. Fly to an unfamiliar airport.
(1) Event Categories and Specific Events. › 8. Fly full published approach.
2. Fly to a non-radar Class D airport.
3. Exhibit adequate knowledge of airspace dimensions and entry requiremen
4. Exhibit adequate knowl
ts.
edge of land-and-hold short operations (LAHSO).
(d)
re.
ted Weather Observing System (AWOS), automated surface observing system (ASOS), automated terminal information se tc.).
oid time via Flight Service Station (FSS).
nt flight rules (IFR) departure.
(e) m length required):
2. Perform landing.
3. Discuss personal minima regarding short runways.
(f) Precision approaches:
1. Fly stabilized final approach segment.
2. Fly approach using AP to Decision Altitude (DA) or the lowest altitude authorized by t hichever is higher.
6. Fly night approach.
7. Fly approach using radar vectors.
8. Fly full published approach.
Class E/G airspace:
1. Fly to an unfamiliar airport.
2. Fly a visual flight rules (VFR) pattern entry/departu
3. Obtain airport weather info via appropriate method (Automa
rvice (ATIS), ATC, e
4. Obtain clearance v
5. Perform an obstacle departure procedure.
6. Perform an instrume
Short runway operation (1.3 times minimu
1. Perform takeoff.
he AFM and Autopilot Limitations, w
3. Fly hand-flown approach.
4. Fly simulated single engine approach.
5. Fly day approach.
9. Fly high-speed/late configuration approach.
ent landing system (ILS) and procedures.
(g) Non-precision approaches:
1. Fly stabilized final approach segment.
(1) Event Categories and Specific Events. › (j) Landings:
2. Fly approach using AP.
3. Fly hand-flown approach.
4. Fly simulated single engine approach.
5. Fly day approach.
6. Fly night approach.
7. Fly approach using vectors.
8. Fly full published approach.
minimum for circling approach (day and night).
(h)
oach to the runway of intended landing (two- engine VFR).
2. Maintain appropriate distance from the airport during the maneuver.
NOTE: Do not exceed 30 degrees of bank angle.
(i) Missed approaches:
1. Fly day missed approach.
2. Fly night missed approach.
3. Fly simulated single engine missed approach.
4. Exhibit adequate knowledge of criteria of when to execute missed approach.
(j) Landings:
10. Exhibit adequate knowledge of the instrum
9. Fly day approach.
10. Fly night approach.
11. Discuss personal
Circling approaches:
1. Fly a stabilized circling appr
(1) Event Categories and Specific Events. › (n) Full mission scenarios.
1. Perform touchdown at desired point.
ay length and condition.
ding.
(k)
e, based on proper fuel reserves.
rformance and fuel requirements.
(l)
in IMC.
5. Exhibit adequate knowledge of icing potential and procedures.
(m) Flight above FL 350:
Demonstrate proper use of supplemental oxygen.
L 350.
from high altitude; exhibit adequate knowledge of m limit speed (VMO/MMO).
(n) rios. Perform flight combining as many of the above event categories as practical; scenario should reflect typical environment expected to be flown by pilot; minimu
2. Perform touchdown at desired speed.
3. Perform touchdown with proper runway alignment.
4. Perform proper braking relative to runw
5. Perform crosswind landing using proper technique.
6. Perform night lan
Maximum range flight:
1. Plan flight to maximum rang
2. Exhibit adequate knowledge of aircraft pe
3. Perform in flight update of fuel status.
4. Discuss diversion options before and during flight.
Actual IMC flight:
1. Perform a departure
2. Perform an arrival in IMC.
3. Perform an instrument approach in IMC.
4. Perform a minimum of 30 minutes cruise in IMC.
6. Exhibit adequate knowledge of how and when to avoid severe weather.
1.
2. Exhibit adequate knowledge of range and speed relationship above F
3. Perform maximum mach/airspeed descent aximum operating
Full mission scena
m events will be:
(1) Event Categories and Specific Events. › 4. Specific simulated emergencies/abnormal operations.
1. Takeoff and landing at different airports.
2. Flight in Class A airspace.
3. Unfamiliar airport operations.
NOTE scenarios.
(o) ation. Fly the aircraft using the AP.
r holding.
Exhibit adequate knowledge of interior and exterior aircraft lighting.
g and operation.
(q) Special operations. These events will be specific to pilot based on recomm
4. Specific simulated emergencies/abnormal operations.
4. Class G airport.
5. Short runway.
: All flights are essentially “full mission”
Autoflight and systems integr
1. Use of the AP fo
2. Use of the AP for tracking.
3. Use of the AP for capturing altitudes.
4. Use of the AP for reducing cockpit workloads.
5. Use of the AP for circling maneuvers.
6. Review of AP limitations.
(p) Night operations:
1.
2. Exhibit adequate knowledge of airport lightin
3. Perform VFR arrival/approach/landing at Class G airport.
4. Discuss personal minima for night flying.
endations from the type rating training summary. They will also be tailored to the specific operations expected to be flown by the pilot. Finally, they may be specifically requested by the pilot. Examples are:
1. High altitude airport operations.
2. Diversion due to simulated low fuel, poor weather, etc.
3. Aircraft handling/visual maneuvers (stalls, steep turns, etc.).
(3) Mentor Qualifications. › (e) 1,500 PIC turbojet.
(2) lot, nd expertise in the complex environments in which the EA-500 will operate. In some cases, there may be a § 61.63(e) Supervised Operating Experience t rized to act as PIC, the mentoring period is a part of EA-500 training program as per the AFM limitation. The pilot will be in the training mode under the direction and supervision nization and the pilot fo -500 standards and procedures e are paramount. The mentor wil
pilot's avia
(g) ndustry as a model of professionalism.
Remain a well-informed aircraft specialist and a resource to fellow pilots. It is the responsibil priority. Th licies and procedures contained in the Flight Training and Standards M
(3) ications. A mentor should be carefully selected based on a superlative record as a professional aviator and aviation instructor, and a demonstrated enthusiasm for aviation in following considerations will contribute to the selection process:
ed in the EA-500.
The Mentor Pilot. A mentor pilot is a professional aviator acting as a coach, co-pi teacher, and role model, sharing experience a
(SOE) restriction that will place PIC responsibility on the mentor. Although the pilo may be type rated and autho
of the mentor pilot. The mentor will be responsible to the training orga r the completion of the training program. Adherence to EA ; and the core values of knowledge, proficiency and attitud l:
(a) Fly with newly type rated EA-500 pilot in the EA-500 to provide wisdom and guidance to the pilot in all aspects of flight.
(b) Counsel the pilot on methods and techniques to enhance safety and improve the tion experience.
(c) Evaluate performance and report progress to the training provider.
(d) Recommend additional training pathways if required.
(e) Uphold the highest standards of proficiency.
(f) Support standard operational procedures established in the AFM and Eclipse EA-500 Flight Training and Standards Manual.
Represent the training provider and the i
(h) ity of the mentor to ensure that every flight is executed with safety as the highest
e mentor will follow the po
anual.
Mentor Qualif
general. Specifically, the
(a) Type rat
(b) Type rated in at least one additional jet aircraft.
(c) 5,000 hours total time.
(d) 3,000 PIC.
(e) 1,500 PIC turbojet.
(f) Previous experience as a flight instructor, check airman, or designated pilot examiner in turbojets.
(g) Able to work with pilots of all levels of experience.
(6) Mentoring Training Records. › (d) Mentor name.
ty terminal areas.
use of aviation resources.
ing airmanship.
(4) stablish a mentor training program. The mentor is required to complete the mentor training. This training includes the following:
(a) EA-500 transition training.
(b) Aircraft-specific instructor training.
(c) Evaluator and rater reliability training.
(d) Right seat training.
(e) Scenario-based mentor training exercises.
red documentation.
entor operation.
(5) Type Rating Training Records. Pilot training records from EA-500 type rating course are mentor pilot is to conduct a thorough review of these records before meeting the pilot for the first time and as required during the mentor program.
number of the authorized mentor pilot.
(h) Operational experience in high densi
(i) Knowledgeable and experienced in the
(j) A record of outstand
Mentor Training. The mentor provider must e
(f) Roles and responsibilities of an EA-500 Mentor Pilot.
(g) Reporting and submission of requi
(h) Making the “OK to Solo” decision.
(i) Standardized operating practices.
(j) The mentor must remain current to conduct m
made available to the mentor pilot before and during the pilot mentoring process. The
(6) Mentoring Training Records. Mentor records on the pilot should be kept by the training provider for at least 24 months. The training records will include:
(a) An events completion record.
(b) Number of hours flown on each flight.
(c) Name and certificate
(d) Mentor name.
a. Recurrent Training-Prerequisites. › (2) Aircraft Systems Training.
(7) Pilot Logbook Endorsement. The pilot’s logbook endorsement will be completed upon satisfactory completion of all required mentoring events. It is incumbent on the mentor to ensure at he/she ct as an unsupervised PIC in the EA-500. Both this
ht rent
ormance during initial type rating training. Customarily, the EA-500 pilo onths after initial type training. Upon successful completion of the second six month recurrent training session the training provider may rec
onth
urrent training between October 1 and December 31 and keep November 30 as recurrent target date/mo
aining instructor to better address a pilot’s level of proficiency in certain areas of operations outlined in the ATP and Type Rating PTS.
(2) Aircraft Systems Training. The self-paced 16 hour minimum aircraft systems training (ca , CD, or DVD) course that covers aircraft systems on the EA-500 will be required to be completed prior to arriving for recurrent training. Sample testing on systems to ensure pilot knowledge is also required. A passing score of 80 percent on the final exam at the end of the training is required to demonstrate knowledge proficiency on the EA-500 systems pri g recurrent training. This is a “train to proficiency” event and should
that the pilot’s performance demonstrates competence in all required events and th demonstrates the ability to a endorsement and the Events Completion Record must be completed by an authorized mentor pilot and an authorized training provider’s department official. An example of the logbook endorsement is shown in Figure 1.
NOTE: Air carrier pilots who operate the EA-500 under part 135 are exempt from the mentor program.
NOTE: FAA inspectors are also exempt from the mentor program.
NOTE: No pilot may be exempt from the minimum SOE specified in § 61.63 if those provisions apply.
7. RECURRENT TRAINING. Under part 61, § 61.58, EA-500 pilots, operating as a single pilot, are not required to have annual PIC proficiency checks. They need only complete a flig review once every two years in any aircraft for which they are rated (part 61, § 61.56). Recur training intervals in the EA-500 are at six month or one-year intervals, depending on the pilot’s total experience and perf
t will accomplish the first recurrent training six m
ommend that the recurrent training interval be extended to one year for that pilot. All “Owner-Operator” (i.e., non 14 CFR part 135) type rated pilots are required to complete recurrent training by the end of the sixth calendar month following the calendar month of completing their type rating. Pilots may complete recurrent training during the calendar m prior or the calendar month after the month in which training is due and still maintain their recurrent training target date/month (i.e., pilot due by November 30 may complete rec
nth).
a. Recurrent Training-Prerequisites.
(1) Pilot Experience Questionnaire. A pilot experience questionnaire will be completed by the pilot prior to attending recurrent training. The completion of the pilot experience questionnaire provides important information with regards to pilot currency, proficiency, and aircraft use during the previous 6-12 month interval. Information collected from the pilot experience questionnaire is used by the tr
n be Web-based training
or to commencin
7. RECURRENT TRAINING. › c. Recurrent Training-Flight/Approved Simulation Device. The recurrent…
a pilot scor the final exam, deficient areas will be reviewed by the pilot and a new exam is taken until a passing score is achieved. The following systems should be included in the aircraft systems training:
w,
FD,
r lighting,
(k) Engines and fire protection,
(l) Climate control,
(m) Oxygen, and
(n) Ice protection.
b. Recurrent Training-Classroom. The classroom phase of recurrent training is designed to prov ing to the continued safe operation of the EA-500. A review of aircraft systems will include a detailed discussion on new
ourse
e less than 80 percent on
(a) Aircraft overview,
(b) Avionics overvie
(c) Avio Power Factor (PF),
(d) Avio M
(e) Air data computer,
(f) Electrical,
(g) Exterior/interio
(h) Flight controls,
(i) Landing gear and brakes,
(j) Fuel,
ide the pilot with supplemental knowledge on selected topics relat
equipment as well as any product improvements to fleet aircraft. Topics should include:
(1) Aircraft systems review.
(2) Standard operating practices review.
(3) Seasonal operating practices review (as required).
(4) Review and analysis of significant safety events in the EA-500 fleet.
(5) Discussion of operating issues identified in the EA-500 fleet.
c. Recurrent Training-Flight/Approved Simulation Device. The recurrent training c is designed to both refresh seldom practiced skills and maneuvers, as well as maintaining a
c. Recurrent Training-Flight/Approved Simulation Device. The recurrent… › (16) Normal and crosswind landings.
pilot’s performance to ATP and Aircraft Type Rating PTS. A common thread throughout the training will continue to be the use of single pilot resource management by constantly evaluatin and mitigating risk throughout all phases of flight. The instructor’s role is to first coach evaluate. This section is normally co
g , then nducted during two days. The first flight day is designed as a maneuvers and instrument refresher. The instructor will assist and explain the maneuvers and procedu for single pilot operations. Day two is considered an evaluation to ATP and Aircraft S. It should be constructed as a scenario-like event. T abnormal, and emergency operations. The instruct aluating pilot performance to a satisfac on and evaluation, the instructor’s ultimat o proficiency, such that known deficiencies are correct ce is brought up to ATP and Aircraft Type Rating PTS. T nsure that the pilot demonstrates a high level of single pilot resource manage ment, aeronautical decision making, automation management, situatio flight/approved simulator training:
(1) Engine start malfunctions.
(2) Normal and crosswind takeoffs.
(3) Normal climb-out and local area clearance.
VFR Maneuvers (as required).
(5)
(6) (VOR) or Localizer (LOC) approaches.
(7) roaches.
(8) trument/Visual Approaches (as required).
MFD failure and reset.
(10) Cabin altitude caution/ emergency descent.
(11) Missed approaches (two engine, single engine, partial flap).
(13) Holding: engine failure and engine restart.
(14) Landing gear failure and emergency gear extension.
(15) Selected emergency procedures.
(16) Normal and crosswind landings.
res, and emphasize techniques
Type Rating PT his scenario should include normal, or’s role will shift primarily to observing and ev tory level in each task. Throughout the observati e responsibility is to train the pilot t ed immediately and pilot performan
he instructor should e
ment skills (risk manage nal awareness, and CFIT awareness). The following should be included in the
(4)
ILS approaches.
Very high frequency Omnidirectional Range
Circling app
Other Ins
(9)
(12) Engine failure on climb out.
7. RECURRENT TRAINING. › d. Recurrent Training Completion Standards. Each pilot must meet the…
(17) After landing/shut
t Training Completion Standards. Each pilot must meet the ATP and Aircraft Type Rating PTS (FAA-S-8081-5, as amended) to successfully complete recurrent training.
down procedures.
d. Recurren
FIGURE 1. ENDORSEMENTS
MENTORING
e) Mentoring
ation EA-500
SOE: § 61. 63(e)
I certify that … (First name, MI, Last name) has completed FAA required supervised operating experience required by § 61.63, and demonstrated the ability to exercise unsupervised PIC privileges in the Eclipse Aviation Corporation EA-500 airplane.
Signed … Date …
ATP/CFI # … Expiration …
I certify that … (First name, MI, Last name) has completed the … (Training Provider’s Nam Program, and has demonstrated competence in all required events and the ability to exercise unsupervised pilot-in-command (PIC) privileges in the Eclipse Aviation Corpor airplane.
Signed … Date …
ATP/CFI # … Expiration …
RECURRENT
I certify that … (First name, MI, Last name) has completed the … (Training Provider’s Name) Recurrent Training Program, and has demonstrated competence to the level of the Airline Transport Pilot and Aircraft Type Rating Practical Test Standards (FAA-S-8081-5, as amended). … (First name, MI, Last name) is on a … (6 month/12 month) recurrent training cycle. The next recurrent training is due … / … (Month/Year) (e.g., Feb/2009).
Signed … Date …
ATP/CFI # … Expiration …