Radar Vectors
Advisory Circular Cancelled Issued Mar 5, 1970 AFS-340 3 pages Copy saved Nov 18, 2026

AC 39-1A JIG Fixtures; Replacement of Wing Attach Angles and Doublers on Douglas DC-3 Series Aircraft, Airworthiness Directive 66-18-2

Describes methods of determining that jig fixtures used in the replacement of the subject attached angles and doublers meet the requirements of Airworthiness Directive 66-18-2.

This document is cancelled. Cancelled by 39-1B. Check the official source before relying on it.

Official source ↗ Open PDF

AC 3991AD A V E : 3/5/70 ADVISORY CIRCULAR ,DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION

JIG FIXTURES; REPLACEMENT OF WING ATTACH ANGLES SUBJECT: AND DOUBLERS ON DOUGLAS DC-3 SERIES AIRCRAFT, AIRWORTHINESS DIRECTIVE 66-18-2

1 0 PURPOSE. This circular describes methods of determining that jig fixtures used in the replacement of the subject attach angles and doublers meet the requirements of Airworthiness Directive 66-18-2.

2 . CANCELLATION. Advisory Circular 39-1, dated 8/l/63, is cancelled.

3 . GENERAL. AD 66-18-2 specifies that Douglas jig fixtures, or their equivalent (that are designed and built for the specific purpose of installation of the new heavier attach angles and doublers on DC-3series aircraft), shall be utilized in the AD compliance.

4 0 ACTION. The use of ac,curate jig fixtures in compliance with the AD

m . is of utmost importance. The determination that satisfactory jigs are utilized may be accomplished in accordance with the following:

a. Obtain jig fixtures, Douglas P/N A652-5110506-l-lF2 and P/N A652-5110506-lF2 or Douglas P/N C652-5110500-lOl-1Fl and P/N C652-5110500-lOl-l-lF1, manufactured by the Douglas Aircraft Company, or

b. Jig fixtures of other manufacture may be forwarded to Douglas Aircraft Company for checking against DACO master tooling, or

c. Authorized persons (appropriately rated certificated mechanics, repair stations, air carriers, or commercial

operators) complying with the AD may make the determination that jig fixtures are DACO equivalent. For this purpose, facilities and equipment should be available for checking the accuracy of these fixtures, particularly in the following critical areas:

Initiatedby:Fs-340

-

F A A figure D o T stamp

Page 2 AC

(1) Fa The vertical face of the jig fixture which will come in contact with the outer wing or

center section attachment surfaces should be smooth and in a straight undeviating plane from leading to trailing edge and from top to bottom of the attach angle and doubler area.

ce Alignment.

(2)Rigidity. The jig should be of such rugged construction 4 that, when bolted to the outer wing or center section for the purpose of installing replacement parts, it should not be possible to pull the jig fixture out of the straight plane alignment specified in (1) above.

(3) B olthole Location. A Douglas manufactured template (which may be obtained from the Product Support Division of DACO) or an equivalent template should be used for determining bolt hole location.

5 . PRECAUTION. For continued accurate results, jig fixtures should be carefully stored to avoid warpage or other damage. Prior to each subsequent use, the jig fixtures should be checked to be sure that original accuracy has been retained.

Advisory Circular Feedback Form

If you find an error in this AC, have recommendations for improving it, or have suggestions for new items/subjects to be added, you may let us know by contacting the Flight Standards Directives Management Officer at [email protected].

Subject: AC 39-1A, Jig Fixtures; Replacement of Wing Attach Angles and Doublers on Douglas DC-3 Series Aircraft, Airworthiness Directive 66-18-2 Date: …

Please check all appropriate line items:

An error (procedural or typographical) has been noted in paragraph … on page …

Recommend paragraph … on page … be changed as follows:

…

…

In a future change to this AC, please cover the following subject: (Briefly describe what you want added.)

…

…

Other comments:

…

…

I would like to discuss the above. Please contact me.

Submitted by: Date: …