Radar Vectors
Advisory Circular Current Issued Aug 19, 2009 ANE-111 161 pages Copy saved Nov 17, 2026

AC 33-8 Guidance for Parts Manufacturer Approval of Turbine Engine and Auxiliary Power Unit Parts under Test and Computation

This advisory circular (AC) provides guidance for developing substantiation data to support the design approval of critical and complex turbine engine and auxiliary power unit (APU) parts produced under parts manufacturer approval (PMA). This guidance is for the comparative test and analysis method used to show compliance to the airworthiness requirements under test and computation, per § 21.303 of Title 14 of the Code of Federal Regulations(14 CFR). This method supports showing the engine or APU still complies with 14 CFR part 33 and Technical Standard Order (TSO) C77. b. Additionally, this AC provides information on developing a continued operational safety (COS) plan and part numbering for turbine engine parts.

Official source ↗ Open PDF

2. Applicability.

Advisory U.S. Department of Transportation Federal Aviation Circular Administration

Subject: Guidance for Parts Manufacturer Date: 8/19/09 AC No: 33-8 Approval of Turbine Engine and Auxiliary Power Unit Parts under Test and

Initiated by: ANE-110

Computation

1. Purpose.

a. This advisory circular (AC) provides guidance for developing substantiation data to support the design approval of critical and complex turbine engine and auxiliary power unit (APU) parts produced under parts manufacturer approval (PMA). This guidance is for the comparative test and analysis method used to show compliance to the airworthiness requirements under test and computation, per § 21.303 of Title 14 of the Code of Federal Regulations (14 CFR). This method supports showing the engine or APU still complies with 14 CFR part 33 and Technical Standard Order (TSO) C77.

b. Additionally, this AC provides information on developing a continued operational safety (COS) plan and part numbering for turbine engine parts.

2. Applicability.

a. This AC provides guidance to applicants requesting PMA for critical and complex turbine engine or APU parts. For the purpose of this AC, the term “engine” represents a turbine engine and an APU, and the term “part” represents a turbine engine part and an APU part.

b. This guidance is neither mandatory nor regulatory in nature and does not constitute a regulation. It describes acceptable means, but not the only means, for demonstrating compliance with the applicable regulations. The FAA will consider other methods of demonstrating compliance that an applicant may elect to present. Terms such as “should,” “shall,” “may,” and “must” are used only in the sense of ensuring applicability of this particular method of compliance when the acceptable method of compliance in this document is used. While these guidelines are not mandatory, they are derived from extensive FAA and industry experience in determining compliance with the applicable regulations. On the other hand, if we become aware of circumstances that convince us that following this AC would not result in compliance with the applicable regulations, we will not be bound by the terms of this AC, and we may require additional substantiation as the basis for finding compliance.

4. Background.

AC 33-8 8/19/09

c. This document does not change, create any additional, authorize changes in, or permit deviations from, existing regulatory requirements.

3. Related References. Please check the FAA’s website at http://www.faa.gov/regulations_policies/ for the latest revision of the following documents.

a. AC 21-9A, Manufacturers Reporting Failures, Malfunctions, or Defects; May 26, 1982.

b. AC 21-1B, Production Certificates; May 10, 1976.

c. AC 33.75-1A, Guidance Material for 14 CFR 33.75, Safety Analysis; September 26, 2007.

d. AC 39-8, Continued Airworthiness Assessments of Powerplant and Auxiliary Power Unit Installations of Transport Category Airplanes; September 8, 2003.

e. Order 8110.37D, Designated Engineering Representative (DER) Handbook; August 10, 2006.

f. Order 8110.42C, Parts Manufacturer Approval Procedures; June 23, 2008.

g. Order 8110.54, Instructions for Continued Airworthiness Responsibilities, Requirements, and Contents; July 1, 2005.

h. Order 8120.2F, Production Approval and Certificate Management Procedures; January 30, 2009.

i. Order 8150.1B, Technical Standard Order Program; May 12, 2002.

4. Background.

a. PMA applicants can show compliance to the airworthiness requirements of the product, i.e., engine certification basis, on which their proposed PMA part is to be installed under test and computation through comparative or general test and analysis, or a combination of both. Applicants requesting PMA for engine parts typically propose comparative test and analysis as the basis for their design approval.

b. When applicants elect to use this comparative test and analysis method to comply with part 33 or TSO C77, the applicant should demonstrate that the functional design of their proposed PMA part is at least equal to that of the original type design part. Applicants frequently use reverse engineering of the type design part to support this approval basis. Although reverse engineering may be adequate to duplicate and substantiate the functional design of a simple engine part, complex or critical engine part designs generally need more rigorous analyses and tests to show equivalency between the type design and the proposed PMA part design. Thus, the test and substantiation plan applicants submit as part of their data package to show compliance

AC 33-8 8/19/09

should reflect the criticality or complexity of their proposed PMA part design to ensure the part meets the airworthiness requirements of part 33 or the standards of TSO C77.

c. The FAA is providing the following guidance to assist applicants in developing the substantiation for the design approval of their complex or critical PMA engine parts when using the comparative test and analysis method.

5. Part Criticality. The data supplied by applicants to substantiate that the part meets the requirements of part 33 or TSO C77 varies depending upon the criticality or complexity of the part. This AC uses part categorization as guidance to applicants for determining whether or not a part is critical or complex.

a. Methods for categorizing parts. This AC categorizes parts based on their most severe potential failure effect using various methods for assessing malfunctions and failure modes. Appendix 1 of this AC provides a failure modes and effects assessment suitable for engines. AC 33.75-1A provides descriptions of other acceptable analytical techniques.

b. Part Categories. The categories that this AC addresses are consistent with the previously established categories used in certificate management oversight, as defined by Order 8120.2. These categories cover potential engine failure effects. These categories are also consistent with AC 39-8, which identifies the relative risks of parts and components that could hazard an aircraft if they fail or malfunction, and are based on historic service data and safety assessments. The part categories are defined as follows:

(1) Category 1. A product, i.e. engine, or part(s) thereof, whose failure could prevent continued safe flight and landing; resulting consequences could reduce safety margins, degrade performance, or cause loss of capability to conduct certain flight operations. A Category 1 part, for the purpose of this AC, meets the definition of a critical part defined in Order 8110.42.

(a) We recommend applicants who are considering applying for a PMA of a Category 1 engine part meet with the project aircraft certification office (PACO) to discuss a test and substantiation plan. Early coordination of these projects will help the applicant identify the necessary technical considerations and airworthiness requirements for that part.

(2) Category 2. An engine or part(s) thereof whose failure would not prevent continued safe flight and landing; resulting consequences may reduce the capability of the aircraft or the ability of the crew to cope with adverse operating conditions or subsequent failures. For the purpose of this AC, a Category 2 engine part is typically a complex part that may affect a critical part.

(a) Together with industry, we developed sample templates as aids to identify technical elements and regulatory requirements generally considered when developing test and substantiation plans. These templates are not all inclusive; rather, they are for a limited number of typical Category 2 engine parts. They are included in Appendix 2 of this AC.

AC 33-8 8/19/09

(b) For Category 2 engine parts, we recommend applicants discuss any questions regarding the templates with the PACO. If a template is not available for a proposed PMA part, we suggest applicants consider developing a new template to identify technical considerations and regulatory requirements. We recommend applicants stay close to the template format provided to do this. We also recommend applicants review the new template with the PACO early in their project to determine if any additional data will be needed.

(3) Category 3. An engine or part(s) thereof whose failure would have no effect on continued safe flight and landing of the aircraft. The only consequence would be partial or complete loss of engine thrust or power (and associated engine services). For single engine applications, consider changing part categorization to category 1 or 2 if complete loss of thrust could prevent continued safe flight and landing or reduce the ability of the crew to cope with adverse operating conditions or subsequent failures.

c. Tables of Potential Failure Effects. The following tables provide potential failure effects for categories 1 and 2. We also listed some examples of parts whose malfunction or failure could result in one or more of the listed potential failure effects.

AC 33-8 8/19/09

Table 1. Category 1

Potential Failure Effects

(1) Non-containment of highenergy debris.

(2) Concentration of toxic products in the engine bleed air intended for the cabin, and sufficient to incapacitate crew or passengers.

Life-limited parts.

Main engine mounts, with no redundant load carrying features.

High pressure vessels (for example, casings subject to compressor discharge pressure and combustor pressure).

(3) Significant thrust in the opposite direction to that commanded by the pilot.

Containment structures.

Fan blades.

(4) Uncontrolled fire. Fuel system shut-off.

(5) Failure of the engine mount system leading to inadvertent engine separation.

(6) Release of the propeller by the engine, if applicable.

(7) Complete inability to shut the engine down.

Primary structures (for example, structures that provide support and rigidity of the main engine backbone and for attachment of engine to airframe).

Thrust reverser control component if thrust reverser control component is part of the engine type certificate (TC).

Part Examples

AC 33-8 8/19/09

Table 2. Category 2

Potential Failure Effects Part Examples

(1) Controlled fires (that is, those brought under control by shutting down the engine or by onboard extinguishing systems).

Rotating parts that are not life-limited (for example, compressor and turbine airfoils).

(2) Case burn-through where it can be shown there is no propagation to hazardous engine effects.

Accessory gearbox and internal components.

(3) Release of low-energy parts where it can be shown there is no propagation to hazardous engine effects.

(4) Vibration levels that result in crew discomfort.

(5) Concentration of toxic products in the engine bleed air for the cabin sufficient to degrade crew performance.

(6) Thrust in the opposite direction to that commanded by the pilot, below the level defined as hazardous.

Engine bearings.

Spinners.

Main engine mounts with redundant load carrying features.

Static gas path parts (for example, vanes and seals).

Control system actuators.

(7) Loss of integrity of the load path of the engine supporting system without actual engine separation.

(8) Generation of thrust greater than maximum rated thrust.

Combustion liners.

Fuel nozzles.

(9) Significant uncontrollable thrust oscillation.

(10) Loss of protection such as loss of overspeed protection or loss of containment case capability.

(11) Effect or influence on a Category 1 part.

AC 33-8 8/19/09

6. Comparative Test and Analysis Method. When using this method to show compliance with part 33 or TSO C77, applicants need to show that the functional design of their proposed PMA part is at least equal to that of the type design part. This showing demonstrates that the original findings of compliance for the engine remain valid. The certification basis of the engine identifies the requirements applicable to the proposed PMA part. For critical and complex parts, the applicant should determine which of the original findings could be affected by their proposed PMA part. To do this, applicants must understand how their part functions in the engine operating environment and the associated airworthiness or TSO requirements. Applicants then develop their substantiation data related to these requirements.

a. Functional design. For the purpose of this AC, functional design is a measure of how well the proposed PMA part adheres to the form, fit, and function of the type design part.

(1) Form is the shape, size, dimensions, and other physical measurable parameters that uniquely characterize a part.

(2) Fit is the ability of a part to interface or interconnect, physically and functionally, at the common boundaries with another part or system of the engine.

(3) Function is the action(s) the part is designed to perform in the engine.

(4) Examples of turbine blade functional design include:

• An airfoil design to extract a desired amount of energy at a prescribed speed. • A blade platform section to provide proper gas path sealing. • A root section for blade retention that interfaces with the disk. • Cooling, materials, and other design features that demonstrate the blade is: • Durable (resistant to oxidation, corrosion, erosion, creep, fatigue, fracture).

• Free of destructive vibratory response. • Reliable.

b. Substantiation data. Examples of this data include:

• Data based on reverse engineering and formal tests and analyses results; • Information from engineering handbooks; • Information based on operational, service, and maintenance experience; • Reliability data; and • Other documented information directly applicable to the airworthiness of the proposed PMA part.

Testing must be designed to evaluate the proposed PMA part side-by-side with the type design part to the extent required by those requirements identified above in paragraph 6.

AC 33-8 8/19/09

7. Reverse Engineering Considerations. Extracting the functional design of a critical or complex part through reverse engineering requires rigorous testing and analyses. This rigorous evaluation (test and analysis) is necessary to determine the dimensional, material, and processing characteristics needed to develop the proposed PMA part design. This part design consists of drawings and specifications, including a list of drawings and specifications needed to define the configuration and design features of the part. It also includes information on materials, dimensions, and processes necessary to define the structural strength of the part and airworthiness limitations, if required.

a. Reverse engineering a critical or complex part design is far more extensive and difficult than creating a computer-aided-drawing or model of that part. Unintended differences can occur when developing the drawings this way. Applicants should consider a rigorous design and review process to minimize these differences. We recommend applicants use specifications such as American Society of Mechanical Engineers ASME Y14.5M Dimensioning and Tolerancing, or an equivalent specification, for data collection techniques.

(1) Since applicants generally don’t know the type design part tolerances before starting a project, determining the measurement method to obtain the required accuracy is a necessary first step. Accuracy is defined as the maximum amount by which the measured result differs from the true value. A general rule of thumb is that measurement accuracy should be at most 10 percent of the expected tolerance. Experience plays a major role in understanding what types of tolerances are used on specific products and features. National standards provided by organizations such as the American Gear Manufacturer’s Association (AGMA) or the American Bearing Manufacturer’s Association (ABMA), or drawings of similar parts, are useful starting points but should not be used in lieu of actual measurement. Also, a feature’s surface finish can provide guidance for required measurement accuracy.

(2) Examples of acceptable measurement accuracies are:

(a) For a roller or ball bearing used in a gas turbine engine, precision measuring equipment capable of measuring to an accuracy of 0.00001 inch or better.

(b) For a precision ground surface used as a land for a carbon seal, optical flats to get the required flatness.

b. When reverse engineering, we recommend taking measurements from multiple type design samples to create the tolerance bands for the drawings and specifications of the proposed PMA part. These tolerance bands tend to be tighter than those of the type design, particularly if based on a limited sample size. A purely statistical method for determining the sample size may result in a sample size which is extensive but not practical. The drawing tolerances determined by reverse engineering for the proposed PMA part should not exceed the measured data (unless substantiated). Applicants should verify that their proposed PMA part can be manufactured to these tighter tolerances. If tighter tolerances cannot be achieved, then the applicant may either:

(1) Analyze more type design parts to expand the reverse-engineered tolerances, change the drawing requirements, and support the manufacturing process; or

AC 33-8 8/19/09

(2) Use a more precise manufacturing method (for example, grinding versus milling) to bring the proposed manufactured part within tolerances.

c. A reverse-engineered PMA part is intended to duplicate the form, fit, and function of the type design part it is planned to replace. Therefore, reverse engineering a part or an assembly is not limited to copying the physical type design part. Some aspects of the type design cannot be revealed through physical observation. For example, the outcome of certain manufacturing processes, such as heat treat and shot peening, can only be evaluated by destructive inspection techniques. Therefore, these types of manufacturing processes must be carefully controlled to ensure the produced PMA part is at least equal to the type design part throughout manufacture. Table 3 provides examples of manufacturing processes that may require control. For PMA parts that have controlled manufacturing processes, we recommend applicants provide their plans for validating these processes at the time of their PMA application. We refer to these plans as source substantiation plans.

Table 3. Typical Controlled Manufacturing Processes

AC 33-8 8/19/09

Table 3. Typical Controlled Manufacturing Processes

1. Abrasive finishing, for example, tumbling and machining 2. Anodizing and hardcoat 3. Brazing 4. Case hardening (case carburizing) 5. Casting processes 6. Chemical cleaning 7. Cold working, for example, bending, straightening, and hammering 8. Conventional machining (feeds, speeds, and tool wear) 9. Diffusion coating (aluminizing) 10. Dry film lube (application of) 11. Electron beam (EB) weld 12. Electro discharge machining (EDM) 13. Forging processes 14. Grit and abrasive blasting (wet or dry) 15. Heat treatment 16. Hot forming 17. Laser drilling (cutting and marking) 18. Plating 19. Rust inhibiting 20. Shot peening 21. Spot and seam welding 22. Spark grinding 23. Titanium chemical cleaning 24. Tungsten inert gas (TIG) welding 25. Tooling design, for example, dies and grip fixtures 26. Vapor degreasing 27. Electro chemical machining (ECM) 28. Composite material manufacturing processes 29. Media (Mass) finish 30. Plasma spraying 31. Titanium welding 32. Bi-metallic welding 33. Electrochemical marking 34. Laser shock peening 35. Elastomeric material processes, for example, curing and mixing 36. Ultrasonic and eddy current inspection (ECI) 37. Inertia welding 38. Translational friction welding 39. Friction stir welding 40. Hole drilling of high length over diameter (L/D) holes 41. Broaching 42. Material removal in general for rotating parts

AC 33-8 8/19/09

d. The part design extracted through reverse engineering data, along with other factors such as service experience, may form the basis on which improvements to features or characteristics are introduced. However, intentional deviation from the type design of critical and complex parts can raise concerns regarding configuration management issues, unintended consequences of the design change, and applicability of the existing instructions for continued airworthiness (ICA). Therefore, applicants should consider introducing a change to their proposed PMA part design only after completing a detailed examination and design evaluation to determine if the change constitutes a major design change per § 21.93. Applicants must clearly identify and justify through engineering evaluation all intentional changes to the proposed PMA part design with the ACO engineer(s) reviewing the design approval.

(1) Configuration management issues can occur because the TC holder can make changes to their part or assembly designs without considering alternate PMA-approved configurations. For instance, if a PMA part adds a disassembly aid feature, such as a tab, and subsequently the TC holder makes a design change to the mating part that creates an interference with the tab on the PMA part, then the PMA part would not be upwardly compatible with the TC holder’s design change.

(2) Unintended consequences may also occur when applicants make changes to their proposed PMA part design. For example, if the PMA holder alters their turbine blade design to make the dovetail stronger, this could change the “weak link” in the system from the blade to the disk post. Consequently, a disk post failure of the PMA part could result in the release of at least two blades and a disk post instead of a single blade, which was the type design intent. Thus, applicants must have a thorough understanding of the relationship between their proposed changes and the assembly in which their part is installed.

(3) Applicants must account for any differences between their proposed PMA part and the type design part when assessing the applicability of the existing ICA, including repair processes. When the proposed PMA part can be installed in multiple engine models, we recommend that applicants consider the most limiting operating or installation conditions, or both, such as:

• Installation applications, such as single engine versus multi-engine aircraft. • Engines approved for Extended Operations (ETOPS). • Recommended operating limitations, such as

• Time Between Overhaul, • Thrust and power ratings, and • Redlines.

e. An outline of a reverse engineering design process for complex parts is provided in Appendix 3.

AC 33-8 8/19/09

8. Continued Operational Safety. PMA holders must support the continued operational safety of their designs. We recommend applicants develop a COS plan to do this. To establish an effective COS plan, applicants should have the ability to assess design, manufacturing, and maintenance issues related to the operation of the engine on which their proposed PMA part is installed.

a. A COS plan generally includes a suitable management plan that includes continuous assessment of the part’s performance in service relative to the applicant’s design assumptions. If a failure, malfunction, or defect in service is identified, the PMA holder must report it as required by § 21.3.

b. A COS plan also includes appropriate methods and resources to identify the cause of a failure, malfunction or in-service defect, develop corrective actions, and implement those actions in a timely manner. Applicants should also validate that the corrective actions restore the engine to an acceptable level of safety.

c. Appendix 4 of this AC provides additional information on how to develop a successful COS plan. If applicants elect to submit a COS plan, they should submit their plan during the design approval phase of the PMA process.

9. Part Numbering. When applicants assign a part number (P/N) to their PMA part, we recommend they use a suffix or prefix of at least 2 letters. The use of a single letter prefix or suffix to the type design part number may result in confusion between the PMA and type design parts. Engine TC holder part numbering practices often employ a single letter prefix or suffix. For example, P/Ns 123456A and 123456B, or A123456 and B123456, designate certain changes to the type design part. Since applicants generally do not have complete knowledge of the type design part number evolution, they should use care when selecting the proposed PMA part number.

Francis A. Favara Manager, Engine and Propeller Directorate Aircraft Certification Service

AC 33-8 8/19/09 Appendix 1

APPENDIX 1. FAILURE MODES AND EFFECTS ASSESSMENT

1. A failure modes and effects assessment is a qualitative process, independent of failure rates and probabilities, by which each failure mode of a part in the engine system is analyzed. Some top-level functions typically considered in an engine failure modes and effects assessment are:

• Maintaining structural integrity, including allowed overspeed and overtemperature exceedances;

• Providing thrust or power; • Operating in inclement weather; • Providing customer bleed, power extraction, or both; and • Meeting fuel consumption, exhaust gas temperature, vibration, emission or noise limits.

2. Each system and subsystem of the engine is broken down into its basic functions using a functional block diagram consistent with the Air Transport Association policy for identification and definition of systems.

3. The functional block diagram defines each system and subsystem, and all their functions, in the turbine engine. The experienced safety engineer performing the analysis determines the partto-part and part-to-system influences in both directions (input and output). The process flow is shown in figure A1.1 below:

Figure A1.1. Process Flow Diagram

Determine input functions from other

engine systems

Identify parts within the system

being analyzed

Determine functions

provided by the part

being analyzed

Determine consequence of failure to provide the desired

function by design intent

Categorize part by outcomes

in Tables 1 and 2 of this AC

Determine outcome on part, engine system, and the engine

Part Interaction. Considerations.

AC 33-8 8/19/09 Appendix 1

4. The part categorization process is built around the fundamental understanding of the part function and its potential effects on physically or functionally mating parts or both. The fundamental premise in the categorization process, and in the physical operation and function of the turbine engine, is system interactions.

a. System interactions are influences a part, or a set of parts, can have on the turbine engine, propulsion system, or aircraft through form, fit, or function. These influences may extend beyond the component being classified, may be direct or indirect, and may develop immediately or over time. Characteristics of these influences include:

(1) Direct influences, which are form and fit. These influences are based on physical contact or interface clearances between adjacent parts.

(2) Indirect influences, which are functional in nature. These influences are not based on physical contact, but may be aerodynamic, thermal, or vibratory.

5. The interactions where the consequence of failure is the furthest from the cause are the most difficult to identify. Many fundamental relationships in part interactions and subsequent system effects exist. Figure A1.2 below provides four examples.

Figure A1.2. Part Interaction Considerations

Indirect Effect 1 Stage 1 HPT Effective Nozzle area/flow

2 Indirect Effect

Fuel Pump Fuel flow Impeller schedule

Time Relationship 3 Stage 2 HPT Cooling flow to Nozzle rotor

Direct Effect

Loads and Rotor Blade moments on

disk

HPC press.

ratio

Stall margin Stall at limiting consumption condition

Fuel to Starting Altitude re-light Combustor characteristic capability

Critical part Purge flow Hot gas

temperature & level ingestion

life

Local dovetail Dovetail or slot LLP life impact loading bottom life

Part Interaction Considerations

•Fluid interactions

• Air, fuel, oil

•Direct interactions

• Mechanical loading

• Aero loading

• Contact/wear

• Chemical

•Indirect interactions

• Vibration

• Acoustical

• Primary air

• Secondary air

• Control system

• Structural dynamics

• Sensor systems

4

AC 33-8 8/19/09 Appendix 2

APPENDIX 2. TEMPLATES

1. This appendix provides 17 templates, listed in Table A2-1 below. The FAA selected them based on what we found applicants were typically submitting for complex turbine engine part PMA approval. These templates will aid applicants in identifying the technical elements and regulatory requirements they should consider when developing their test and substantiation plans. Applicants must ensure that any additional technical criteria or regulatory requirements are met for their specific proposed PMA part. Each template is subdivided into the following sections:

a. Section 1 - Part functional capability, which is the action the part is designed to perform in the engine.

b. Section 2 - Part shape, size, dimensions, and other physical, measurable parameters; interconnectivity with an engine integral part or system; or both.

c. Section 3 – Part materials and processes – properties.

d. Section 4 – Part materials and processes – processing.

e. Section 5 - Applicable analyses.

f. Section 6 - Applicable testing.

g. Section 7 - Applicable regulatory requirements.

2. Sections 1 through 5 are divided into the following five columns:

a. Column 1 is the section number.

b. Columns 2 and 3 identify part characteristics to be evaluated to support the functional design intent of the type design part.

c. Column 4 identifies typical areas applicants should evaluate for potential part and system failure modes.

d. Column 5 is used to identify a combination of actions and criteria for risk mitigation and control when a corresponding failure mode is identified in column 4.

3. Section 7 of the templates identifies the part 33 (Amendments 1-20 inclusive) airworthiness requirements applicable to turbine engines. However, not all engine certification bases include the same requirements.

4. If a template is not available for a particular part, the applicant can create or modify another as necessary. For example, although templates specific to APU parts are not provided, the

AC 33-8 8/19/09 Appendix 2

applicant may use the templates for similar APU parts and revise the regulatory section to reflect the requirements of TSO C77.

Table A2-1. Available Templates

Template Number

Part Name

1 O-Rings 2 Embedded elastomer seals 3 Combustor 4 Low pressure turbine blade 5 Turbine vane cooled 6 Turbine vane un-cooled 7 Shaft 8 Roller bearing 9 Ball bearing 10 Gear 11 Compressor vane 12 Compressor blade 13 Static air seal 14 Variable stator vane lever arms 15 Bushings 16 Turbine blade cooled 17 Fuel filter

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #1: O-Rings

This template deals with non-standard seals which are typically procured under a TC holder part number. If the part is listed as a

standard part and can be procured commercially these requirements do not apply.

Inner

Diameter Outer

Diameter

Width

Mold Line/Flash

Cross-Section

Shape May Vary

Nomenclature for Generic Component Features

(all features may not be applicable)

17

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Static Size • Physical dimension • Dimensionally within limits • Dimensional process

control

1-2 Material • Actual material used in part • Base material certifications • Verify certificates

1-3 Temperature limits • Maximum and minimum temperatures • Recommended limits by manufacturer • Verify capability exceeds

expected duty cycle

1-4 Chemical resistance • Compatibility with TC holder approved fluids in applicable system. • Recommended limits by manufacturer • Verify capability exceeds

expected duty cycle

• Verify chemical

compatibility with TC

holder approved fluids.

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Boundary

dimensions • Inside diameter • Outside diameter • Cross sectional size

• Installation into assembly • Dimensional process

control and inspection

2-2 Surface finish • Actual surface conditions • Ability to perform sealing function • Dimensional process

control

2-3 Fit-up dimensions • Design compression/expansion • set/spring back • Ensure compression is within the allowable range • Dimensional process

control and inspection

2-4 Tolerance • Variance-Fluctuations in measurements • Mechanical/Functional, failure due to variation from

nominal • Verify part is tolerant to

variation

• Control of manufacturing

and inspection processes

18

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % Variation

• Impurities • Poor mechanical or environmental resistance properties • Material selection

• Process control

3-2 Physical properties • Density

• Coefficient of thermal expansion

• Melting Point

• Consistent properties within operating parameters • Material selection

• Process control

3-3 Mechanical

properties • Modulus

• Hardness/Durometer hardness • Low material properties • Adequate material properties

• Operational effects accounted for

3-4 Environmental

resistance • Oxidation

• Temperature range

• Corrosion

• Chemical resistance

• Age related material property change

• Physical deterioration from

Oxidation/Corrosion/chemical attack

• Property reduction due to extreme temperatures

• Verify adequate environmental

properties

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Raw material processing • Purity • Inadequate material properties • Process control (melt

control, cleanliness)

• Process control and

sequencing

4-2 Surface treatment • Proper form and texture • Improper thickness and excess flash • Process control

4-3 Process sequencing and

Significant Process

Identification and

Substantiation

• Inspection • Manufacturing • Process Substantiation and Control (RSS,RSA,ESA, etc)

• Inadequate final part form, or defect “escape” • Verify adequate control

of processes and

parameters

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Temperatures • Sealing ability • Proper contact pressures

• Inadequate part life due to analysis under-predicting part temperature, mechanical stress, chemical resistance • Perform analysis at relevant operating conditions

5-2 Variation • Engine operation characteristics • Inadequate part function due to variation • Verify part is tolerant to variation

19

AC 33-8 8/19/09 Appendix 2

Section 6 – Testing

Section/Number Characteristic Critical

to Part Functionality Key Characteristics Part and System Failure

Section 7 – Potential Impact on Regulatory Requirements

Modes Risk Mitigation and

Control

6-1 Durability • Engine vibration response • Leakage • Excessive leakage

• Excessive Vibration • Perform adequate

component and/or

engine testing

6-2 Operability and

performance • Vibration signature • Abnormal wear • Environmental testing to hot and cold limitations for the engine. Thermal conditions at the “O” ring seal installed

location

• Durability/replacement interval(s)/shelf life, etc, if applicable?

• Excessive leakage

• Difficult to

disassemble after

operation

• Engine testing

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits for leakage

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

20

AC 33-8 8/19/09 Appendix 2

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue)

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention Could be affected No fluid leakage

8. 33.19 Durability Could be affected

9. 33.21 Engine cooling

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

Subpart E – Design and Construction;

Turbine Aircraft Engines

15. 33.62 Stress analysis

16. 33.63 Vibration Could be affected

17. 33.65 Surge and stall characteristics

18. 33.66 Bleed air systems

19. 33.67 Fuel system Could be affected Leakage limits

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system Could be affected Leakage limits

23. 33.72 Hydraulic actuating system Could be affected Leakage limits

24. 33.73 Power or thrust response

25. 33.74 Continued rotation

26. 33.75 Safety analysis

21

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction;

Turbine Aircraft Engines

27. 33.76 Bird ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Leakage limits

34. 33.88 Engine over temperature test

35. 33.89 Operation test

36. 33.90 Initial maintenance inspection Could be affected Leakage limits

37. 33.91 Engine component tests

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes)

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B - Certification Standard

Atmospheric Concentrations of Rain and Hail

22

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #2: Embedded Elastomer Seals

This template deals with non-standard seals which are typically procured under an OEM part number. If the part is listed as a

standard part and can be procured commercially, these requirements do not apply.

Elastomeric Seal (Lip)

Puller Feature

Seal Diameter

Nomenclature for Generic Component Features

(all features may not be applicable)

23

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Static size • Physical dimension of seal and carrier • Dimensions are within limits • Dimensional process

control

1-2 Material • Actual material used in part • Base material certifications • Process control

1-3 Temperature limits • Maximum and minimum temperatures • Recommended limits by manufacturer • Verify capability exceeds

expected duty cycle

1-4 Chemical resistance • List of chemicals which the material is compatible with • Recommended limits by manufacturer • Surface dimensional

process control

• Verify acceptable wear

• Verify chemical

compatibility with

approved engine fluids.

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Boundary

dimensions • Hole locations • Inside contour • Outside contour • Cross sectional size of elastomer • Thickness of carrier

• Installation into assembly • Dimensional process

control and inspection

2-2 Surface finish • Actual surface conditions • Ability to perform sealing function • Dimensional process

control

2-3 Fit-up dimensions • Design compression/expansion • Ensure compression is within the allowable range • Dimensional process

control and inspection

2-4 Tolerance • Variance-fluctuations in measurements • Parallelism of carrier • Mechanical/Functional, failure due to variation from

nominal • Verify part is tolerant to

variation

• Control of manufacturing

and inspection processes

24

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % variation • Impurities • Poor mechanical or environmental resistance properties • Material selection

• Process control

3-2 Physical properties • Density • Coefficient of thermal expansion • Melting point

• Consistent properties within operating parameters • Material selection

• Process control

3-3 Mechanical

properties • Modulus • Surface hardness • Low material properties • Adequate material properties

• Operational effects accounted for

3-4 Environmental

resistance • Oxidation • Temperature range • Corrosion • Chemical resistance

• Physical deterioration from

Oxidation/Corrosion/chemical attack

• Property reduction due to extreme temperatures

• Verify adequate environmental

properties

• Verify chemical compatibility with

approved engine fluids.

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Raw material processing • Purity • Inadequate material properties • Process control (melt

control, cleanliness)

• Process control and

sequencing

4-2 Surface treatment • Proper form and texture • Improper thickness and excess flash • Process control

4-3 Process sequencing and

Significant Process

Identification and

Substantiation

• Inspection • Manufacturing • Process Substantiation and Control (RSS,RSA,ESA, etc)

• Inadequate final part form, or defect “escape” • Verify adequate control

of processes and

parameters

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Temperatures • Sealing ability • Proper contact pressures • Location of flange surfaces

• Inadequate part life due to analysis under-predicting part temperature, mechanical stress, chemical resistance • Perform analysis at relevant operating conditions

5-2 Variation • Engine operation characteristics • Inadequate part function due to variation • Verify part is tolerant to variation

25

AC 33-8 8/19/09 Appendix 2

Section 6 – Testing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

Section 7 – Potential Impact on Regulatory Requirements

6-1 Durability • Engine vibration response • Leakage • Excessive vibration

• Excessive leakage • Perform adequate

component and/or engine

testing

6-2 Operability and

performance • Vibration signature • Abnormal wear on affected parts • Excessive vibration

• Difficult to disassemble after operation • Engine testing

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits for leakage

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations Could be affected Adequate sealing required throughout engine operating envelope.

4. 33.8 Selection of engine power and thrust ratings

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue)

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention Could be affected No fluid leakage

8. 33.19 Durability Could be affected

26

AC 33-8 8/19/09 Appendix 2

Subpart B – Design and Construction;

General

9. 33.21 Engine Cooling

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

Subpart E – Design and Construction;

Turbine Aircraft Engines

15. 33.62 Stress Analysis

16. 33.63 Vibration Could be affected

17. 33.65 Surge and stall characteristics

18. 33.66 Bleed air systems

19. 33.67 Fuel system Could be affected Leakage limits

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system Could be affected Leakage limits

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response

25. 33.74 Continued rotation

26. 33.75 Safety Analysis

27. 33.76 Bird Ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

27

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction;

Turbine Aircraft Engines

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Leakage limits

34. 33.88 Engine over temperature test

35. 33.89 Operation test

36. 33.90 Initial maintenance inspection Could be affected Leakage limits

37. 33.91 Engine component

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes)

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B - Certification Standard

Atmospheric Concentrations of Rain and Hail

28

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #3: Combustor

Nomenclature for Generic Component Features

(all features may not be applicable)

29

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Weight • As-cast surfaces • Machined surfaces • Surface dimensional process control

1-2 Profile • Inner and outer wall contours • Nozzle area • Operability effects • Emissions • Turbine airfoils durability

• Surface dimensional process control

1-3 Cooling/Dilution air

utilization • Total flow rate • Individual nozzle swirler/heatshield flow rate • ID/OD profile • Static pressure distribution

• Over-temperature/dysfunction • Emissions • Improper temperature profile: over-temperature/dysfunction of downstream airfoils

• Cooling and dilution hole dimensional process control

• Burner rig testing

1-4 Structural strength • Combustor hood locating pins • Static structure malfunction • Resonance avoidance at steady state operation with

margin

1-5 Creep, LCF, fracture

toughness, tensile

overload capability

• Geometry • Cooling • Material mechanical/metallurgical/physical properties

• Crack growth from LCF or Creep – Rupture • Verify capability exceeds expected utilization

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Inner and outer

shells • Profile and length • Axial location of forward and aft face • Functional fits at interfaces • Part/assembly locating features (axial, radial and tangential)

• Air sealing surfaces • Cooling and dilution holes

• Emissions effects • Combustor exit profile effects (pattern factor) • Lean blowout • Rumble or combustion Instability

• Dimensional process control and inspection

• Burner rig testing

2-2 Hood • Fuel nozzle location • Cooling hole location • Leading edge profile

• Durability • ID/OD airflow distribution • Lean blowout

• Dimensional process control • Burner rig testing

2-3 Fuel nozzle swirlers • Radial location • Cooling hole pattern • Size

• Durability • Surface dimensional process control

30

AC 33-8 8/19/09 Appendix 2

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-4 Cast panels • Profile • Cooling pin/fin size and location • Emissions • Durability • Dimensional process control

2-5 Tolerance • Variance-Fluctuations in measurements • Measurement gauge repeatability and reliability • Mechanical/Functional, failure due to vibration from nominal • Verify part is tolerant to variation

• Control of manufacturing and inspection processes

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % variation • Impurities • Poor mechanical or environmental properties • Poor TBC adherence • Material selection • Master heat and process control 3-2 Physical properties • Density • Coefficient of thermal expansion • Refractive Index (x-rays)

• Excessive weight • Excessive thermal stresses • Interference with surrounding hardware

Verify:

• Acceptable weight • Acceptable stresses • Combustor “fit” in hot condition 3-3 Mechanical

/metallurgical

properties

• Modulus (vs. grain orientation) • Bare and coated: tensile (UTS, YS, elongation, stress rupture, creep, LCF,

HCF)

• Long term metallurgical stability

• Excessive strain-controlled stress • Undesirable natural frequency • Low material properties, dysfunction • Material capability consumed in operation

Verify:

• Acceptable stresses and frequencies • Adequate material properties • Operational effects accounted for • Relevant properties are used 3-4 Cast structure • Grain Structure (size, shape, flow, boundaries, gamma prime size and volume

fraction)

• Low angle boundaries • Directional properties • Hardness • Melting Point • Crack propagation rate

• Material property reduction due to excessive grain angle or low angle boundaries, cast panel dysfunction • Verify that grain orientation or low angle boundaries are accounted for

• Process control and inspection

3-5 Environmental

resistance • Oxidation, corrosion, erosion, fretting resistance

• Elevated temperature (creep, diffusion, ageing, temp. gradients)

• FOD resistance

• Cracking from oxidation/corrosion pitting, dysfunction • Verify adequate environmental properties

31

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-6 Environmental

coating • Coverage and thickness • Long term stability • Oxidation and corrosion resistance

• LCF property reduction due to poor coating selection/requirements, panel cracking

• Cracking from oxidation/corrosion pitting

• Control of chemistry and application process

• Verify thermal-mechanical compatibility with base material

3-7 Thermal barrier

coating • Coating material composition and density • Thermal conductivity (coefficient of thermal expansion)

• Coverage and thickness uniformity • Coating and diffusion zone microstructure • Adhesion • Oxidation • Resistance to spalling, sintering and erosion

• Hardness • Residual Stress • Stripping requirements • Bonding (Interface Contamination) • Compatibility with base material/other coatings

• High thermal stresses or part temperature, swirler and panel dysfunction • Control of chemistry and application process

• Verify part is tolerant to missing TBC • No high TBC temperatures that accelerate spalling

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Casting cleanliness • Inclusions and porosity • Internal surface cleanliness • Crack growth from inclusion or porosity • Poor coating adhesion, corrosion and oxidation • Process control (mold setup, casting process, and

filtration)

• Process control and sequencing

4-2 Heat treatment • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere

• Incorrect Gamma Prime size/spacing leading to low material properties • Process control and sequencing

32

AC 33-8 8/19/09 Appendix 2

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-3 Welding and brazing Effect on base material properties, based on the

following:

• Weld or braze strength • Microstructure (grain size, shape, flow, braze gap, defects, grain boundary precipitates,

gamma prime and volume fraction

• Porosity • Diffusion zone (brazing) • Heat affected zone (welding) • Penetration (welding) • Excess braze allowance • Filler metal selection

• Material property reduction • Correct sequencing of braze or weld cycles in the

process

• Process control

4-4 Material removal – Non

traditional (EDM, ECM,

Laser, Water-Jet, etc.)

and conventional

(machining, milling,

broaching, grinding,

blending, honing,

lapping, stripping, etc.)

Micro cracks or recast:

• Inherent to the process • Due to abusive machining Fatigue capability degradation, due to:

• Surface finish • Stress risers • Chemical attack

• Cracking initiation from micro-cracks or re-cast • Verify part is tolerant to proposed limits

• Process control

4-5 Non-destructive testing

(NDT) • Acceptance limits • Sensitivity • Cracking from excessive defect size • Verify part is tolerant to allowable defects

4-6 Process sequencing and

Significant Process

Identification and

Substantiation

• Inspection • Manufacturing • Process substantiation and control (RSS, RSA, ESA, etc)

• Inadequate final part form, or defect “escape”, dysfunction • Verify adequate control of processes and parameters

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Flow path temperatures, pressures, and velocities

• Nozzle area • Exit profile

• Compressor operability • Turbine airfoil durability • Perform analysis at relevant operating conditions

5-2 Swirler cooling • Secondary flow circuit • Swirler cooling flow • Inadequate part life due to analysis over-predicting the swirler cooling effectiveness

33

AC 33-8 8/19/09 Appendix 2

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-3 LCF/TMF life

analysis • Temperature effects • Multi-axial effects • Hold time effects • Mean stress effects • Notch effects • Coating effects • Mesh size

Inadequate part life due to analysis

• Using incorrect properties • Failing to address the ‘key characteristics’

• Use applicable properties • Select mesh size to correctly model the geometry

5-4 HCF life analysis • Temperature effects • Vibration and mean stress effects • Combustor resonant vibration, cracking, dysfunction • Use applicable properties and Goodman Diagram

5-5 Creep and rupture

life analysis • Temperature effects • Material thickness effects • Combustor rupture cracking, dysfunction • Use applicable properties

5-6 Fracture mechanics • Temperature effects • Threshold stress intensity • Crack growth rate

• Crack growth from defect • Use applicable dA/dN curve • Predict K using expected defect size

5-7 Tolerance to

missing TBC • Part temperature • Thermal stress • High thermal stress or part temperature, dysfunction • Perform analysis with predicted TBC loss

Section 6 – Testing

Section/Number Characteristic

Key

Characteristics Part and System Failure Modes Risk Mitigation and Control

6-1 Durability • Fatigue • Corrosion (hot and cold)

• Erosion • Stress rupture • Tensile strength • Cooling Effectiveness 6-2 Over-temperature • Microstructure • Creep • Hot corrosion • Tensile strength 6-3 Emissions • Smoke, HC, CO, NoX

34

Section 7 – Potential Impact on Regulatory Requirements

AC 33-8 8/19/09 Appendix 2

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue)

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention

8. 33.19 Durability Could be affected

9. 33.21 Engine cooling Could be affected

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

35

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction;

Turbine Aircraft Engines

15. 33.62 Stress analysis

16. 33.63 Vibration

17. 33.65 Surge and stall characteristics Could be affected In-flight relighting

18. 33.66 Bleed air systems

19. 33.67 Fuel system

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response Could be affected Timed accels

25. 33.74 Continued rotation

26. 33.75 Safety analysis Could be affected Combustor part release – downstream effects

27. 33.76 Bird ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Combustor durability and starting capability

34. 33.88 Engine over temperature test

35. 33.89 Operation test

36

AC 33-8 8/19/09 Appendix 2

Subpart F – Block Tests; Turbine Aircraft

Engines

36. 33.90 Initial maintenance inspection Could be affected Combustor in-service inspection limits

37. 33.91 Engine component tests

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes)

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B - Certification Standard

Atmospheric Concentrations of Rain and Hail

37

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #4: Low Pressure Turbine Blade

Attachment or Dovetail

Airfoil

Platform

Seal Knives Cross Notch/Cross

Shroud

Nomenclature for Generic Component Features

(all features may not be applicable)

38

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Weight • As-cast surfaces • Machined surfaces Dovetail/attachment and disk loading-dysfunction Surface dimensional process

control

1-2 Moment of weight -

center of gravity

• Axial • Tangential • Radial

• As-cast surfaces • Machined surfaces • Mass/density distribution

Dovetail/attachment and disk loading-dysfunction Surface dimensional process

control

1-3 Cooling air utilization

(If cooled) • Total flow rate • Individual circuit-cavity flow rate • Flow distribution • Static pressure distribution • Discharge pressure at showerhead, relative to turbine gas flow pressure

• Low flow: blade over-temperature/dysfunction • High flow: reduced rotor cavity purge/ingestion/part dysfunction

• Poor distribution of cooling air: over-temperature, and existing bench flow limits not valid

1-4 Vibration damping • Damper fit to blade • Damping ratio Blade vibration: Blade or disk dovetail cracking Control damper seating with

blade and/or disk

1-5 Vibration

characteristics (HCF

Capability)

• Blade natural frequencies • Vibration stress distribution • Cycles to failure demonstration • Vibration test set-up and execution criteria, i.e., establishing parameters for blade holding,

loading, excitation modes determination, and

excitation sensing techniques

Blade resonant vibration, cracking, dysfunction • Resonance avoidance at steady state operation with

margin

• Vibratory and steady state stress within Goodman

diagram limits

1-6 Creep, LCF, fracture

toughness, tensile

overload capability

• Blade geometry • Blade cooling • Material mechanical/metallurgical/physical properties

• Blade cleaning requirements/effectiveness (internal passages-intergranular attack)

• Blade separation from tensile overload • Crack growth from LCF or creep – rupture • Loss of tip fatigue strength from rubbing

Verify capability exceeds

expected utilization

39

AC 33-8 8/19/09 Appendix 2

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and

interconnectivity with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Dovetail

or attachment • Shape • Flatness • Tang relative location and taper • Tolerance (blade root and disk fir tree dimensional spectrums and blade

producibility limitations)

• Unbalance tang loading/blade dysfunction • Incorrect loading on disk/cracking Dimensional process control

and inspection

2-2 Platform • Width • Angel wing length • Width: binding/damping loss, leakage/cavity ingestion • Angel wing: cavity ingestion or rotor/stator rubs Dimensional process control

2-3 Airfoil external

shape • Aero contour/stagger angle • Thickness distribution • Twist/lean/bow

• Poor aero performance • Airfoil vibratory mode changes due to thickness distribution • Blade throat area – Bearing load, cavity purge, operability, work split, stage loading

Surface dimensional process

control

2-4 Airfoil wall

thickness

(if cooled)

Thickness vs. chord and span • Weight • Airfoil stress/life Dimensional process control

2-5 Airfoil internal

cavities

(if cooled)

• Passage area and blockage • Turbulator height and shape • Internal wall coating

• Small area: large pressure loss, backflow, ingestion, overtemperature

• Large area: Insufficient blade cooling

Dimensional process control

and inspection of passage

geometry

2-6 Cross notch/cross

shroud Notch shape and thickness

• Pre-twist • Seal teeth geometry

• Blade to blade tip loading o Insufficient. Excessive vibe stress, etc

o Excessive. High mechanical stress, etc

• Poor tip sealing, excessive leakage, poor performance

Dimensional/coating process

control

2-7 Tolerance • Variance-fluctuations in measurements • Measurement gauge repeatability and reliability

Mechanical/Functional, failure due to vibration from nominal • Verify part is tolerant to variation

• Control of manufacturing and inspection processes

40

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % Variation • Impurities • Poor mechanical or environmental properties • Poor coating adherence Material selection

Master heat and process control

3-2 Physical properties • Density • Thermal conductivity • Coefficient of thermal expansion • Refractive index (x-rays) • Melting point

• Excessive blade weight • Excessive thermal stresses • Interference with surrounding hardware

Verify:

• Acceptable blade weight • Acceptable stresses • Blade “fit” in hot condition

3-3 Mechanical

/metallurgical

properties

• Modulus (vs. grain orientation) • Columnar crystal orientation angles • Bare and coated: tensile (UTS, YS, elongation, stress rupture, creep, LCF, HCF)

• Long term metallurgical stability • Thin wall effects (if cooled)

• Excessive strain-controlled stress • Undesirable natural frequency • Low material properties, blade dysfunction • Material capability consumed in operation • Low material properties, blade dysfunction

Verify:

• Acceptable stresses and frequencies • Grain orientation, as required • Adequate material properties • Operational effects accounted for • Relevant properties are used 3-4 Cast structure • Grain structure (size, shape, flow, boundaries, gamma prime size and volume

fraction)

• Low angle boundaries • Directional properties • Hardness • Melting point • Crack propagation rate • Refractive index

Material property reduction due to excessive grain angle

or low angle boundaries, blade dysfunction Verify that grain orientation or low angle

boundaries are accounted for

Process control and inspection

3-5 Environmental

resistance • Oxidation, corrosion, erosion, fretting resistance

• Elevated temperature (creep, diffusion, ageing, temp. gradients)

• Rubbing, FOD resistance

Cracking from oxidation/corrosion pitting, blade

dysfunction Verify adequate environmental

properties

3-6 Environmental

coating • Coverage and thickness • Long term stability • Oxidation and corrosion resistance

• LCF property reduction due to poor coating selection/requirements, blade cracking

• Cracking from oxidation/corrosion pitting

Control of chemistry and application

process

Verify thermal-mechanical compatibility

with base material

3-7 Notch coating • Coating material composition and density • Coverage and thickness uniformity • Coating and diffusion zone microstructure • Adhesion • Hardness • Residual stress • Stripping requirements • Bonding (interface contamination) • Compatibility with base material/other coatings

High blade stress due to improper blade tip gapping.

• Insufficient gap, high mechanical stress, etc • Excessive gap, excessive vibe stress, etc

Control of chemistry and application

process

41

AC 33-8 8/19/09 Appendix 2

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Casting cleanliness • Inclusions and porosity • Internal surface cleanliness Crack growth from inclusion or porosity

Poor coating adhesion, corrosion and oxidation Process control (mold setup,

casting process, and filtration)

Process control and

sequencing

4-2 Heat treatment • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere

Incorrect Gamma prime size/spacing leading to

low material properties Process control and

sequencing

4-3 Welding and brazing Effect on base material properties, based on the

following:

• Weld or braze strength • Microstructure (grain size, shape, flow, braze gap, defects, grain boundary precipitates,

gamma prime and volume fraction

• Porosity • Diffusion zone (brazing) • Heat affected zone (welding) • Penetration (welding) • Excess braze allowance • Filler metal selection

Material property reduction Correct sequencing of braze

or weld cycles in the process

Process control

4-4 Shot peen • Intensity • Coverage Incorrect dovetail compressive stress, cracking,

and blade dysfunction Process control

4-5 Material removal – Non

traditional (EDM, ECM,

laser, water-jet, etc.)

and conventional

(machining, milling,

broaching, grinding,

blending, honing,

lapping, stripping, etc.)

Micro cracks or recast:

• Inherent to the process • Due to abusive machining Fatigue capability degradation, due to:

• Surface finish • Stress risers • Chemical attack

Cracking initiation from micro-cracks or re-cast Verify part is tolerant to

proposed limits

Process control

4-6 Non-destructive testing

(NDT) • Acceptance limits • Sensitivity Cracking from excessive defect size Verify part is tolerant to

allowable defects

4-7 Process sequencing

and Significant

Process Identification

and Substantiation

• Inspection • Manufacturing • Process substantiation and control (RSS, RSA, ESA, etc)

Inadequate final part form, or defect “escape”,

blade dysfunction Verify adequate control of

processes and parameters

42

AC 33-8 8/19/09 Appendix 2

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Flow path temperatures, pressures, and velocities

• Rotor speed

Inadequate part life due to analysis under-predicting part

temperature, thermal or mechanical stress Perform analysis at relevant

operating conditions

5-2 Blade cooling

(if cooled) • Secondary flow circuit • Blade cooling flow • Blade cooling

Inadequate part life due to analysis over-predicting the blade

cooling

5-3 LCF life analysis –

airfoil and shank • Temperature effects • Multi-axial effects • Hold time effects • Mean stress effects • Notch effects • Coating effects • Mesh size

Inadequate part life due to analysis

• Using incorrect properties • Failing to address the ‘key characteristics’

Use applicable properties

Select mesh size to correctly model

the geometry

5-4 HCF life analysis • Temperature effects • Vibration and mean stress effects Blade resonant vibration, cracking, dysfunction Use applicable properties and

Goodman diagram

5-5 Creep and rupture

life analysis • Temperature effects • Material thickness effects Blade rupture cracking, dysfunction Use applicable properties

5-6 Fracture mechanics • Temperature effects • Threshold stress intensity • Crack growth rate

Crack growth from defect Use applicable dA/dN curve

Predict K using expected defect

size

5-7 Tolerance to

missing coating • Part temperature • Thermal stress High thermal stress or part temperature, blade dysfunction Perform analysis with predicted

coating loss

5-8 Variation • Blade or engine characteristics • Degree of variation required to assure adequate vibratory stress

dampening.

Inadequate part life due to vibration Verify part is tolerant to vibration

5-9 Life calculation • Predicted stress and Temperature • Root loading profile shifts • Material Properties • Operating during part life • Life impact on disk

Inadequate part life due to analysis under-predicting Verify correct inputs to lifing

process

Verify correct ‘mission mixing’ used

43

Section 7 – Potential Impact on Regulatory Requirements

AC 33-8 8/19/09 Appendix 2

Section 6 – Testing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

6-1 Durability • Fatigue • Corrosion (hot and cold) • Erosion • Creep • Stress rupture • Tensile strength • Cooling effectiveness • Internal contamination • Cleaning requirements • Vibration 6-2 Over-temperature • Microstructure • Creep • Hot corrosion • Tensile strength

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

44

AC 33-8 8/19/09 Appendix 2

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue) Could be affected Weight and center-of-gravity affect on rotor forces and LCF capability

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention

8. 33.19 Durability Could be affected Durability; weight and failure modes relative to containment capability

9. 33.21 Engine cooling

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors Could be affected Weight affect on rotor forces during over-speed

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

Subpart E – Design and Construction:

Turbine Aircraft Engines

15. 33.62 Stress analysis Could be affected

16. 33.63 Vibration Could be affected Blade vibration-Design

17. 33.65 Surge and stall characteristics Could be affected Turbine effective area-Operating line migration, Blade-Rub strip interaction

18. 33.66 Bleed air systems

19. 33.67 Fuel system

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response Could be affected Turbine efficiency/performance

25. 33.74 Continued rotation

26. 33.75 Safety analysis Could be affected Turbine blade release-Case containment

45

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction:

Turbine Aircraft Engines

27. 33.76 Bird ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test Could be affected Blade vibration

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Blade durability

34. 33.88 Engine over temperature test Could be affected Blade over temperature capability

35. 33.89 Operation test

36. 33.90 Initial maintenance inspection Could be affected Blade in-service inspection limits

37. 33.91 Engine component tests

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes) Could be affected Failure of the most critical turbine blade while operating at maximum

permissible r.p.m.

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B - Certification Standard

Atmospheric Concentrations of Rain and Hail

46

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #5: Turbine Vane Cooled

Nomenclature for Generic Component Features

(all features may not be applicable)

47

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Weight • As-cast surfaces • Machined surfaces Engine mass and CG Surface dimensional process

control

1-2 Cooling air utilization • Total flow rate • Individual circuit-cavity flow rate • Flow distribution • Static pressure distribution • Discharge pressure at showerhead, relative to turbine gas flow pressure

• Distribution of post and pre impingement air to the rotor cavities

• Low vane cooling flow: vane over-temperature/dysfunction • High vane cooling flow, and/or low purge cavity delivery flow; reduced rotor cavity purge/ingestion/part dysfunction

• Poor distribution of cooling air: over-temperature, and existing bench flow limits not valid

1-3 Structural strength

and vibration

characteristics

• Vane natural frequencies • Major load path • Vane resonant vibration, cracking, dysfunction • Static structure malfunction • Resonance avoidance at steady state operation with

margin

• Vibratory and steady state stress within Goodman

diagram limits

1-4 Creep, LCF, fracture

toughness, tensile

overload capability

• Vane geometry • Vane cooling • Material mechanical/metallurgical/physical properties

• Vane cleaning requirements/effectiveness (internal passages-intergranular attack)

• Crack growth from LCF or creep – rupture Verify capability exceeds

expected utilization

48

AC 33-8 8/19/09 Appendix 2

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and

interconnectivity with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Inner and outer

platforms • Arc length • Axial location of forward and aft face • Functional fits at interfaces • Part/assembly locating features (axial, radial and tangential)

• Inner and outer gas path contours • Air sealing surfaces (axial, radial and tangential)

• Surface finish

• Unbalance: tang loading/dysfunction • Width: binding, leakage/cavity ingestion Dimensional process control

and inspection

2-2 Airfoil external

shape • Aero contour/stagger angle • Thickness distribution • Effects on down stream turbine blades

• Poor aero performance • Airfoil vibratory mode changes due to thickness distribution • Vane throat area – bearing load, cavity purge, operability, work split, stage loading

Surface dimensional process

control

Assessment of exit flow

characteristics

2-3 Airfoil wall

thickness Thickness vs. chord and span • Weight • Airfoil stress/life Dimensional process control

2-4 Airfoil internal

cavities • Passage area and blockage • Turbulator height and shape • Internal wall coating

• Small area: large pressure loss, backflow, ingestion, overtemperature

• Large area: insufficient vane cooling

Dimensional process control

and inspection of passage

geometry

2-5 Tolerance • Variance-fluctuations in measurements • Measurement gauge repeatability and reliability

Mechanical/Functional, failure due to vibration from nominal • Verify part is tolerant to variation

• Control of manufacturing and inspection processes

2-6 Cooling baffle • Mass flow • Standoff • Low flow: excessive pressure loss, back flow, etc • High flow: low impingement cooling, excessive part temp, etc • Low standoff: low impingement cooling, excessive part temp, etc

• Verify part is tolerant to variation

• Control of manufacturing and inspection processes

2-7 Interstage seal • Dimension • Honeycomb dimensions • Insufficient interstage sealing: Insufficient upstream cavity purge, etc

• Excessive interstage sealing: Insufficient downstream cavity purge, etc

• Poor cutting characteristics, rubbing, thermal instability, etc

• Verify part is tolerant to variation

• Control of manufacturing and inspection processes

2-8 Airfoil to platform

filets • Filet profile • Failure due to stress concentration. • Dimensional process control.

49

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes – Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % variation • Impurities • Poor mechanical or environmental properties • Poor TBC adherence Material selection

Master heat and Process control

3-2 Physical properties • Density • Coefficient of thermal expansion • Refractive index (x-rays)

• Excessive vane weight • Excessive thermal stresses • Interference with surrounding hardware

Verify:

• Acceptable vane weight • Acceptable stresses • Vane “fit” in hot condition 3-3 Mechanical

/metallurgical

properties

• Modulus (vs. grain orientation) • Columnar crystal orientation angles • Bare and coated: tensile (UTS, YS, elongation, stress rupture, creep, LCF, HCF)

• Long term metallurgical stability • Thin wall effects

• Excessive strain-controlled stress • Undesirable natural frequency • Low material properties, vane dysfunction • Material capability consumed in operation

Verify:

• Acceptable stresses and frequencies • Grain orientation, as required • Adequate material properties • Operational effects accounted for • Relevant properties are used

3-4 Cast structure • Grain structure (size, shape, flow, boundaries, gamma prime size and volume fraction,

recrystallization)

• Inclusions • Freckling • Porosity • High angle boundaries - directional properties • Hardness • Melting point • Crack propagation rate • Refractive index

Material property reduction due to excessive grain

angle or high angle boundaries (HAB), Verify that grain orientation or high angle

boundaries are accounted for

Process control and inspection

3-5 Environmental

resistance • Oxidation, corrosion, erosion, fretting resistance • Elevated temperature (creep, diffusion, ageing, temp. gradients)

• FOD resistance

Cracking from oxidation/corrosion pitting, vane

dysfunction Verify adequate environmental

properties

3-6 Environmental

coating • Coverage and thickness • Long term stability • Oxidation and corrosion resistance

• LCF property reduction due to poor coating selection/requirements, vane cracking

• Cracking from oxidation/corrosion pitting

• Control of chemistry and application process

• Verify thermal-mechanical compatibility with base material

50

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes – Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-7 Thermal barrier

coating • Coating material composition and density • Thermal conductivity (coefficient of thermal expansion)

• Coverage and thickness uniformity • Coating and diffusion zone microstructure • Adhesion • Oxidation • Resistance to spalling, sintering and erosion • Hardness • Residual Stress • Stripping requirements • Bonding (interface contamination) • Compatibility with base material/other coatings

High thermal stresses or part temperature, vane

dysfunction • Control of chemistry and application process

• Verify part is tolerant to missing TBC • No high TBC temperatures that accelerate spalling, or molten dirt

infiltration

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Casting cleanliness • Inclusions and porosity • Internal surface cleanliness Crack growth from inclusion or porosity

Poor coating adhesion, corrosion and oxidation • Process control (mold setup, casting process, and

filtration)

• Process control and sequencing

4-2 Heat treatment • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere

Incorrect Gamma prime size/spacing leading to

low material properties Process control and

sequencing

4-3 Welding and brazing Effect on base material properties, based on the

following:

• Weld or braze strength • Microstructure (grain size, shape, flow, braze gap, defects, grain boundary precipitates,

gamma prime and volume fraction

• Porosity • Diffusion zone (brazing) • Heat affected zone (welding) • Penetration (welding) • Excess braze allowance • Filler metal selection

Material property reduction • Correct sequencing of braze or weld cycles in the

process

• Process control

4-4 Shot peen • Intensity • Coverage Incorrect compressive stress, cracking, and vane

dysfunction Process control

51

AC 33-8 8/19/09 Appendix 2

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-5 Material removal – Non

traditional (EDM, ECM,

laser, water-jet, etc.)

and conventional

(machining, milling,

broaching, grinding,

blending, honing,

lapping, stripping, etc.)

Micro cracks or recast:

• Inherent to the process • Due to abusive machining Fatigue capability degradation, due to:

• Surface finish • Stress risers • Chemical attack

Cracking initiation from micro-cracks or re-cast • Verify part is tolerant to proposed limits

• Process control

4-6 Non-destructive testing

(NDT) • Acceptance limits • Sensitivity Cracking from excessive defect size Verify part is tolerant to

allowable defects

4-7 Process sequencing

and significant process

identification and

substantiation

• Inspection • Manufacturing • Process substantiation and control (RSS, RSA, ESA, etc)

Inadequate final part form, or defect “escape”,

vane dysfunction Verify adequate control of

processes and parameters

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Flow path temperatures, pressures, and velocities • Nozzle Area Compressor operability Perform analysis at relevant

operating conditions

5-2 Vane cooling • Secondary flow circuit • Vane cooling flow • Vane cooling

Inadequate part life due to analysis over-

predicting the vane cooling

5-3 LCF/TMF life

analysis – airfoil

and shrouds

• Temperature effects • Multi-axial effects • Hold time effects • Mean stress effects • Notch effects • Coating effects • Mesh size

Inadequate part life due to analysis

• Using incorrect properties • Failing to address the ‘key characteristics’

Use applicable properties

Select mesh size to correctly

model the geometry

5-4 HCF life analysis • Temperature effects • Vibration and mean stress effects Vane resonant vibration, cracking, dysfunction Use applicable properties and

Goodman Diagram

5-5 Creep and rupture

life analysis • Temperature effects • Material thickness effects Vane rupture cracking, dysfunction Use applicable properties

5-6 Fracture mechanics • Temperature effects • Threshold stress intensity • Crack growth rate

Crack growth from defect • Use applicable dA/dN curve • Predict K using expected defect size

5-7 Tolerance to

missing TBC • Part temperature • Thermal stress High thermal stress or part temperature, vane

dysfunction Perform analysis with predicted

TBC loss

52

AC 33-8 8/19/09 Appendix 2

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-8 Variation • Nozzle or engine characteristics Inadequate part life due to vibration Verify part is tolerant to vibration

5-9 Life calculation • Predicted stress and temperature • Material properties • Operating during part life

Inadequate part life due to analysis under-

predicting Verify correct inputs to lifing

process

Verify correct ‘mission mixing’

used

Section 6 – Testing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

6-1 Durability • Fatigue • Corrosion (hot and cold) • Erosion • Creep • Stress rupture • Tensile strength • Cooling effectiveness • Internal contamination • Cleaning requirements 6-2 Over-temperature • Microstructure • Creep • Hot corrosion • Tensile strength

53

Section 7 – Potential Impact on Regulatory Requirements

AC 33-8 8/19/09 Appendix 2

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue) Could be affected Turbine cooling

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention

8. 33.19 Durability Could be affected

9. 33.21 Engine cooling Could be affected

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

54

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction;

Turbine Aircraft Engines

15. 33.62 Stress analysis Could be affected Turbine cooling

16. 33.63 Vibration Could be affected Vane vibration

17. 33.65 Surge and stall characteristics Could be affected Turbine effective area-Operating line migration

18. 33.66 Bleed air systems

19. 33.67 Fuel system

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response Could be affected Turbine efficiency/performance

25. 33.74 Continued rotation

26. 33.75 Safety analysis Could be affected Turbine vane release – downstream effects

27. 33.76 Bird ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test Could be affected Vibration

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Vane durability

34. 33.88 Engine over temperature test Could be affected Vane over temperature capability

35. 33.89 Operation test

36. 33.90 Initial maintenance inspection Could be affected Blade in-service inspection limits

55

AC 33-8 8/19/09 Appendix 2

Subpart F – Block Tests; Turbine Aircraft

Engines

37. 33.91 Engine component tests

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes)

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B - Certification Standard

Atmospheric Concentrations of Rain and Hail

56

AC 33-8 8/19/09 Appendix 2

Template #6: Turbine Vane Uncooled

Inner Shroud, Ring

or Platform

Vane Airfoil

Nomenclature for Generic Component Features

Vane Packets (may be

segmented or continuous)

Outer Shroud or Ring

Nomenclature for Generic Component Features

(all features may not be applicable)

57

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Weight • As-cast surfaces • Machined surfaces Engine mass and CG Surface dimensional process

control

1-2 Structural strength

and vibration

characteristics

• Vane natural frequencies • Major load path • Vane resonant vibration, cracking, dysfunction • Static structure malfunction • Resonance avoidance at steady state operation with

margin

• Vibratory and steady state stress within Goodman

diagram limits

1-3 Creep, LCF, fracture

toughness, tensile

overload capability

• Vane geometry • Vane cooling • Material mechanical/metallurgical/physical properties

• Vane cleaning requirements/effectiveness (internal passages-intergranular attack)

Crack growth from LCF or creep – rupture Verify capability exceeds

expected utilization

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Inner and outer

shroud or platform • Arc length • Axial location of forward and aft face • Functional fits at interfaces • Part/assembly locating features (axial, radial and tangential)

• Inner and outer airsealing surfaces (axial, radial and tangential)

• Inner and outer gas path contours • Sealing surfaces, surface finish

Unbalance tang loading/blade dysfunction Dimensional process control

and inspection

2-2 Platform • Width Width: binding, leakage/cavity ingestion Dimensional process control

2-3 Airfoil external

shape • Aero contour/stagger angle • Thickness distribution • Poor aero performance • Airfoil vibratory mode changes due to thickness distribution • Effect on downstream turbine blade vibratory response • Vane throat area – bearing load, cavity purge, operability, work split, stage loading

• Weight

Surface dimensional process

control

58

AC 33-8 8/19/09 Appendix 2

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and interconnectivity

with an engine integral part/system

2-4 Tolerance • Variance-fluctuations in measurements • Measurement gauge repeatability and reliability Mechanical/functional, failure due to vibration from nominal • Verify part is tolerant to variation

• Control of manufacturing and inspection processes

2-5 Interstage seal • Dimension • Honeycomb dimensions • Insufficient interstage sealing: Insufficient upstream cavity purge, etc.

• Excessive interstage sealing: Insufficient downstream cavity purge, etc.

• Poor cutting characteristics, rubbing, thermal instability, etc

• Verify part is tolerant to variation

• Control of manufacturing and inspection processes

2-6 Airfoil to platform

filets • Filet profile Failure due to stress concentration • Dimensional process control

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % variation • Impurities • Poor mechanical or environmental properties • Poor TBC adherence Material selection

Master heat and process control

3-2 Physical properties • Density • Coefficient of thermal expansion • Refractive Index (x-rays)

• Excessive Vane Weight • Excessive thermal stresses • Interference with surrounding hardware

Verify:

• Acceptable vane weight • Acceptable stresses • Vane “fit” in hot condition 3-3 Mechanical

/metallurgical

properties

• Modulus (vs. grain orientation) • Columnar crystal orientation angles • Bare and coated: tensile (UTS, YS, elongation, stress rupture, creep, LCF,

HCF)

• Long term metallurgical stability

• Excessive strain-controlled stress • Undesirable natural frequency • Low material properties, vane dysfunction • Material capability consumed in operation

Verify:

• Acceptable stresses and frequencies • Grain orientation, as required • Adequate material properties • Operational effects accounted for • Relevant properties are used 3-4 Cast structure • Grain structure (size, shape, flow, boundaries, gamma prime size and volume

fraction, recrystallization)

• Inclusions • Freckling • Porosity • High angle boundaries directional properties

• Hardness • Melting point • Crack propagation rate • Refractive index

Material property reduction due to excessive grain angle or

high angle boundaries (HAB), • Verify that grain orientation or high angle boundaries are accounted for

• Process control and inspection

59

AC 33-8 8/19/09 Appendix 2

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-5 Environmental

resistance • Oxidation, corrosion, erosion, fretting resistance

• Elevated temperature (creep, diffusion, ageing, temp. gradients)

• FOD resistance

Cracking from oxidation/corrosion pitting, vane dysfunction • Verify adequate environmental properties

3-6 Environmental

coating • Coverage and thickness • Long term stability • Oxidation and corrosion resistance

• LCF property reduction due to poor coating selection/requirements, vane cracking

• Cracking from oxidation/corrosion pitting

• Control of chemistry and application process

• Verify thermal-mechanical compatibility with base material

3-7 Thermal barrier

coating (if used) • Coating material composition and density • Thermal conductivity (coefficient of thermal expansion)

• Coverage and thickness uniformity • Coating and diffusion zone microstructure • Adhesion • Oxidation • Resistance to spalling, sintering and erosion

• Hardness • Residual stress • Stripping requirements • Bonding (interface contamination) • Compatibility with base material/other coatings

High thermal stresses or part temperature, vane dysfunction • Control of chemistry and application process

• Verify part is tolerant to missing TBC • No high TBC temperatures that accelerate spalling, or molten dirt

infiltration

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Casting cleanliness • Inclusions and porosity • Internal surface cleanliness Crack growth from inclusion or porosity

Poor coating adhesion, corrosion and oxidation • Process control (mold setup, casting process, and

filtration)

• Process control and sequencing

4-2 Heat treatment • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere

Incorrect Gamma prime size/spacing leading to

low material properties Process control and

sequencing

60

AC 33-8 8/19/09 Appendix 2

Section 4 – Part Materials and Processes - Processing

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-3 Welding and brazing Effect on base material properties, based on the

following:

• Weld or braze strength • Microstructure (grain size, shape, flow, braze gap, defects, grain boundary precipitates,

gamma prime and volume fraction

• Porosity • Diffusion zone (brazing) • Heat affected zone (welding) • Penetration (welding) • Excess braze allowance • Filler metal selection

Material property reduction Correct sequencing of braze

or weld cycles in the process

Process control

4-4 Shot peen • Intensity • Coverage Incorrect compressive stress, cracking, and vane

dysfunction Process control

4-5 Material removal – Non

traditional (EDM, ECM,

laser, water-jet, etc.)

and conventional

(machining, milling,

broaching, grinding,

blending, honing,

lapping, stripping, etc.)

Micro cracks or recast:

• Inherent to the process • Due to abusive machining Fatigue capability degradation, due to:

• Surface finish • Stress risers • Chemical attack

Cracking initiation from micro-cracks or re-cast Verify part is tolerant to

proposed limits

Process control

4-6 Non-destructive testing

(NDT) • Acceptance limits • Sensitivity Cracking from excessive defect size Verify part is tolerant to

allowable defects

4-7 Process sequencing and

significant process

identification and

substantiation

• Inspection • Manufacturing • Process substantiation and control (RSS, RSA, ESA, etc)

Inadequate final part form, or defect “escape”,

vane dysfunction Verify adequate control of

processes and parameters

61

AC 33-8 8/19/09 Appendix 2

Section 5 – Analysis

Section/Number Characteristic

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating

conditions • Flow path temperatures, pressures, and velocities

• Nozzle area

Compressor operability Perform analysis at relevant

operating conditions

5-2 LCF/TMF life

analysis – airfoil

and shrouds

• Temperature effects • Multi-axial effects • Hold time effects • Mean stress effects • Notch effects • Coating effects • Mesh size

Inadequate part life due to analysis

• Using incorrect properties • Failing to address the ‘key characteristics’

Use applicable properties

Select mesh size to correctly model

the geometry

5-3 HCF life analysis • Temperature effects • Vibration and mean stress effects Vane resonant vibration, cracking, dysfunction Use applicable properties and

Goodman Diagram

5-4 Creep and rupture

life analysis • Temperature effects • Material thickness effects Vane rupture cracking, dysfunction Use applicable properties

5-5 Fracture mechanics • Temperature effects • Threshold stress intensity • Crack growth rate

Crack growth from defect Use applicable dA/dN curve

Predict K using expected defect

size

5-6 Tolerance to

missing TBC • Part temperature • Thermal stress High thermal stress or part temperature, vane dysfunction Perform analysis with predicted

TBC loss

5-7 Variation • Nozzle or engine characteristics Inadequate part life due to vibration Verify part is tolerant to vibration

5-8 Life calculation • Predicted stress and temperature • Material properties • Operating during part life

Inadequate part life due to analysis under-predicting Verify correct inputs to lifing

process

Verify correct ‘mission mixing’ used

62

Section 7 – Potential Impact on Regulatory Requirements

AC 33-8 8/19/09 Appendix 2

Section 6 – Testing

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

6-1 Durability • Fatigue • Corrosion (hot and cold) • Erosion • Creep • Stress rupture • Tensile strength • Internal contamination • Cleaning requirements 6-2 Over-temperature • Microstructure • Creep • Hot corrosion • Tensile strength

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

63

AC 33-8 8/19/09 Appendix 2

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue)

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention

8. 33.19 Durability Could be affected

9. 33.21 Engine cooling

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

Subpart E – Design and Construction:

Turbine Aircraft Engines

15. 33.62 Stress Analysis

16. 33.63 Vibration Could be affected Vane vibration

17. 33.65 Surge and stall characteristics Could be affected Turbine effective area-Operating line migration

18. 33.66 Bleed air systems

19. 33.67 Fuel system

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response Could be affected Turbine efficiency/performance

25. 33.74 Continued rotation

26. 33.75 Safety analysis Could be affected Turbine vane release

64

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction:

Turbine Aircraft Engines

27. 33.76 Bird ingestion (Operability aspects of ingestion)

28. 33.77 Foreign object ingestion (Operability aspects of ingestion)

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

Subpart F – Block Tests; Turbine Aircraft

Engines

31. 33.83 Vibration test Could be affected Vibration

32. 33.85 Calibration tests

33. 33.87 Endurance test Could be affected Vane durability

34. 33.88 Engine over temperature test Could be affected Vane over temperature capability

35. 33.89 Operation test

36. 33.90 Initial maintenance inspection Could be affected Blade in-service inspection limits

37. 33.91 Engine component tests

38. 33.92 Rotor locking tests

39. 33.93 Teardown inspection

40. 33.94 Blade containment and rotor unbalance tests (Weight changes)

41. 33.95 Engine-propeller system tests

42. 33.96 Engine tests in auxiliary power unit (APU) mode

43. 33.97 Thrust reversers

44. 33.99 General conduct of block tests

45. Part 33 - Appendix A – Instructions for Continued

Airworthiness Could be affected

46. Part 33 - Appendix B- Certification Standard

Atmospheric Concentrations of Rain and Hail

65

Nomenclature for Generic Component Features

AC 33-8 8/19/09 Appendix 2

Template #7: Shaft – Not Life-limited

Active Surface

Spline Threaded Feature

Balance Areas

Material

Wall Thickness

Run Out

Shoulder Feature

Nomenclature for Generic Component Features

(all features may not be applicable)

66

AC 33-8 8/19/09 Appendix 2

Section 1 – Part Functional capability, i.e., the action(s)

that the part is designed to perform in the product

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

1-1 Weight • As-forged surfaces • Machined surfaces • Inertia • Surface dimensional process control

1-2 Shaft geometry • Diameters • Attachment point form • Surface finish • Surface hardness

• Correct length • Heat dissipation • Vibration response

• Dimensional control • Machining process control

1-3 Vibration

characteristics (HCF

capability)

• Shaft natural frequencies • Vibration stress distribution • Cycles to failure demonstration

• Shaft resonant vibration, cracking • Resonance avoidance at steady state operation with

margin

• Vibratory and steady state stress within Goodman

diagram limits

1-4 LCF, fracture

toughness, tensile

overload capability

• Shaft geometry • Material mechanical/metallurgical/physical properties

• Shaft separation from overload • Crack growth from LCF, HCF, or HCF/LCF interaction • Verify capability exceeds expected duty cycle

1-5 Attachment features • Surface finish • Press fit • Retaining thread • Wear resistance on mating component • Splines

• Surface fret • Bearing spinning • Dimensional checks

• Surface dimensional process control

• Verify acceptable wear couple

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and

interconnectivity with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-1 Shaft features • Shape • Surface finish • Internal/external diameter • Edge break, relief cuts • Splines • Threads • Integral raceways • Oil holes

• Vibration • Resonant frequencies • Scuffing

• Dimensional process control and inspection

2-2 Feature locations • Distance to features from datum • Parts mislocated with in engine • Dimensional process control

67

AC 33-8 8/19/09 Appendix 2

Section 2 – Part Shape, size, dimensions and other

physical measurable parameters, and

interconnectivity with an engine integral part/system

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

2-3 Wall thickness • Transition areas • Thickness distribution • Attaching features • Dampening features • Balancing features

• Gear vibratory mode changes due to thickness distribution • Weight – excessive inertia load • Stress/life

• Surface dimensional process control

2-4 Tolerance • Variance-fluctuations in measurements • Measurement gauge repeatability and reliability

• Mechanical/functional, failure due to variation from nominal • Verify part is tolerant to variation

• Control of manufacturing and inspection processes

Section 3 – Part Materials and Processes –

Properties

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

3-1 Chemistry • Major elements - % variation • Impurities Poor mechanical or environmental properties Material selection

Process control

3-2 Physical properties • Density • Coefficient of thermal expansion • Melting point

• Excessive weight • Excessive loading on retaining features Verify:

• Acceptable stresses • Operating conditions 3-3 Mechanical

/metallurgical

properties

• Modulus • Forging grain flow angles • Tensile, UTS, YS, elongation, stress rupture, creep, LCF, HCF

• Endurance limit • Fracture mechanics • Plasticity model • Sudden overload properties • Surface hardness

• Undesirable natural frequencies • Low material properties: shaft yield or break • Spalling during operation

Verify:

• Acceptable stresses and frequencies • Forging grain flow as required • Adequate material properties • Operational effects accounted for • Impact testing

3-4 Forged structure • Grain structure (size, shape, flow, boundaries)

• Directional properties • Hardness • Forging laps • Homogeneity of forging work throughout part

Material property reduction due to abnormal grain

structure, vibration, Verify that variations in grain structure

are accounted for

Process control & inspection

3-5 Environmental

resistance • Oxidation, corrosion, fretting resistance • Elevated temperature stress relaxation • Surface coating

• Spalling from oxidation/corrosion pitting • Property reduction due to extreme oil overtemperature or lack of cooling oil

Verify adequate environmental

properties

68

AC 33-8 8/19/09 Appendix 2

Section 4 – Part Materials and Processes - Processing

Number Characteristic Critical

to Part Functionality Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

4-1 Raw material processing • Inclusions and porosity • Micro structural characteristics • Crack growth from inclusion or porosity • Inadequate material properties Process control (melt control,

cleanliness

Process control and sequencing

4-2 Heat treatment • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere • Tooling and fixturing

• Incorrect structure leading to low material properties Process control and sequencing

4-3 Welding Effect on base material properties, based on the

following:

• Weld strength • Microstructure: grain size, shape, flow, defects, grain boundary precipitates

• Porosity • Heat affected zone • Filler metal selection • Joint design

• Material property reduction • Weld failure Correct sequencing of weld

process

Process control

4-4 Peening • Intensity • Coverage • Incorrect compressive stress, cracking Process control

4-5 Surface hardening • Time @ temperature and ramp rates • Manufacturing sequence • Atmosphere • Tooling and fixturing

• Improper case depth • Hardness improper Process control

4-7 Non-destructive testing

(NDT) • Acceptance limits • Sensitivity • Cracking from excessive defect size Verify part is tolerant to

allowable defects

4-8 Process sequencing and

significant process

identification and

substantiation

• Inspection • Manufacturing • Process substantiation and control (RSS,RSA,ESA, etc)

• Inadequate final part form, or defect “escape” Verify adequate control of

processes and parameters

4-9 Forging process Forging structure

• Grain Structure (size, shape, flow, boundaries) • Directional properties • Hardness • Forging laps • Homogeneity of forging work throughout part

• Material property reduction due to abnormal grain structure Process control and sequencing

4-10 Surface treatments Effect on base material properties, based on the

following:

• Carburizing • Shot peening • Coating • Polishing

• Material property reduction due to improper processing Process control and sequencing

69

AC 33-8 8/19/09 Appendix 2

Section 5 – Analysis

Key Characteristics Part and System Failure Modes Risk Mitigation and Control

5-1 Operating conditions • Torque loads • Oil temperatures • Speeds • Transient loads

• Inadequate part life due to analysis under-predicting part

temperature, mechanical stress • Perform analysis at relevant

operating conditions

5-2 LCF life assessment • Temperature effects • Overloads • Inadequate part life due to analysis

• Using incorrect properties

• Failing to address the ‘key characteristics’

• Use applicable properties

• Select mesh size to correctly

model the geometry

5-3 HCF life analysis • Temperature effects • Vibration and mean stress effects • Shaft resonant vibration, cracking, whipping

• Critical frequency, bending modes • Use applicable properties and

Goodman Diagram

5-4 Fracture mechanics • Temperature effects • Threshold stress intensity • Damage tolerance

• Crack growth from defect • Use applicable dA/dN curve

• Predict K using expected

defect size

5-5 Variation • Engine operation characteristics • Inadequate part life due to variation • Verify part is tolerant to

variation

5-6 Life calculation • Predicted stress and temperature • Material properties • Operation during part life

• Inadequate part life due to analysis under-predicting • Verify correct inputs to lifing

process

Section 6 – Testing

Key Characteristics Part and System Failure Modes Risk Mitigation and

Control

6-1 Durability • Fatigue • Tensile strength • Spalling • Engine vibration response • Microstructure

• Shaft separation • Perform adequate

component and/or engine

testing

6-2 Operability and

performance • Vibration signature • Excessive vibration • Engine testing

6-3 Locating features • Build tolerances • Engine manual build sheets • Process control

70

AC 33-8 8/19/09 Appendix 2

Section 7 – Potential Impact on Regulatory Requirements

Note: The regulatory requirements identified below, which are inclusive up to Amendment 20 of 14 CFR part 33, are intended as a guide to

Section 7 – Potential Impact on Regulatory Requirements

applicants when determining the applicable regulations to which they must show compliance. Those requirements listed as “Could be

affected” highlight the regulations whose compliance findings are typically affected by the component or part that this template is addressing.

This guide is not all-inclusive and the applicant remains responsible for identifying the certification basis of the product on which their PMA

part is to be installed.

Applicable 14 CFR Part 33 Regulatory

Requirements Comments

Subpart A – General

1. 33.4 Instructions for Continued Airworthiness Could be affected ICAs including on-wing inspection requirements and on-wing limits

2. 33.5 Instruction manual for installing and operating the engine

3. 33.7 Engine ratings and operating limitations

4. 33.8 Selection of engine power and thrust ratings

Subpart B – Design and Construction;

General

5. 33.14 Start-stop cyclic stress (low cycle fatigue)

6. 33.15 Materials Could be affected

7. 33.17 Fire prevention

8. 33.19 Durability Could be affected

9. 33.21 Engine cooling

10. 33.23 Engine mounting attachments and structure

11. 33.25 Accessory attachments

12. 33.27 Turbine, compressor, fan, and turbosupercharger rotors

13. 33.28 Electrical and electronic control systems

14. 33.29 Instrumentation connection

71

AC 33-8 8/19/09 Appendix 2

Subpart E – Design and Construction;

Turbine Aircraft Engines

15. 33.62 Stress analysis Could be affected Shaft stress analysis

16. 33.63 Vibration Could be affected Shaft vibration

17. 33.65 Surge and stall characteristics

18. 33.66 Bleed air systems

19. 33.67 Fuel system

20. 33.68 Induction system icing (Operability aspects)

21. 33.69 Ignition system

22. 33.71 Lubrication system

23. 33.72 Hydraulic actuating system

24. 33.73 Power or thrust response

25. 33.74 Continued rotation Could be affected Continued integrity

26. 33.75 Safety analysis Could be affected Shaft release

27. 33.76 Bird ingestion (Operability aspects of ingestion) Could be affected Sudden shaft loading

28. 33.77 Foreign object ingestion (Operability aspects of ingestion) Could be affected Sudden shaft loading

29. 33.78 Rain and hail ingestion

30. 33.79 Fuel burning thrust augmenter

72

Continue reading ↓ 120 of 254 passages shown