Radar Vectors
Advisory Circular Cancelled Issued Dec 2, 1992 ACE-100 159 pages Copy saved Nov 18, 2026

AC 23-11 [Large AC] Type Certification of Very Light Airplanes with Powerplants and Propellers Certified to Parts 33 and 35 of the Federal Aviation Regulations

Provides an acceptable means of compliance with Part 23 of the FAR for type certification of certain small airplanes.

This document is cancelled. Cancelled by 23-11A. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file. Check the original, as some words may be misread.

Advisory

US.Department of Transportation Federal Aviation Circular

Administration

Subject: TYPE CERTIFICATION OF VERY Date: 12/2/92 AC No: 23-11 LIGHT AIRPLANES WITH POWER- Initiated by: ACE-100 Change: PLANTS AND PROPELLERS CERTIFICATED TO PARTS 33 AND 35 OF THE FEDERAL AVIATION REGULATIONS

1. PURPOSE. This advisory circular (AC) provides an acceptable means but not the only means of compliance with part 23 of the Federal Aviation Regulations (FAR) for type certification of certain small airplanes. This guidance material is neither mandatory ncr regulatory in nature and does not constitute a regulation in itself. It is for guidance purposes and provides an example of a method of compliance that has been found acceptable. Because the method of compliance presented in this AC is not mandatory, the terms "shall" and must" used in this AC apply only to an applicant who chooses to follow this particular method without deviation. The applicant may elect to follow an alternate method provided the alternate method is also found acceptable by the FAA.

2. RELATED REGULATIONS AND DOCUMENTS.

a. Section 21.5--Airplane or Rotorcraft Flight Manual.

b. Section 21.17--Designation of applicable regulations.

c. Section 21.21--Issue of type certificate; normal, utility, acrobatic, commuter, .and transport category aircraft; manned free balloons, special classes of aircraft; aircraft engines; propellers.

d. Section 21.29--Issue of type certificate; import products.

e. Part 23--Airworthiness standards: normal, utility, acrobatic, and commuter category airplanes.

.f. Part 33--Airworthiness standards: aircraft engines.

g. Part 35--Airworthiness standards: propellers.

h. Part 36--Noise standards: aircraft type and airworthiness certification.

i. Part 39--Airworthiness directives.

j. .Part 43--Maintenance, preventive maintenance, rebuilding, and alteration.

AC 23-11 12/2/92

k. Part 45, Subpart C--Nationality and registration marking.

1. Section 91.9--Civil aircraft flight manual, marking, and placard requirements.

m. Section 91.205--Powered civil aircraft with standard category U.S. airworthiness certificates: Instrument and equipment requirements.

n. "Flight Test Guide for Certification of Part 23 Airplanes," Advisory Circular 23-8A, Federal Aviation Administration (FAA), dated February 9, 1989.

o. "Designated Engineering Representatives," AC 183.29-1Z, FAA, dated July 12, 1991.

p. "Designated Airworthiness Representatives (DAR's), Designated Alteration Stations (DAs's), and Delegation Option Authorization (DOA) Directory," AC 183-35B, FAA, dated March 7, 1989.

q. "Equipment, Systems, and Installations in Part 23 Airplanes," AC 23.1309-1A, FAA, dated June 3, 1992.

r. "Aircraft Certification Directorate Procedures," FAA Order 8100.5, dated October 1, 1982.

s. "Type Certification," FAA Order 8110.4, dated December 28, 1967.

All free AC's may be obtained from the U.S. Department of Transportation; Utilization and Storage Section, M-443.2, Washington, D.C. 20590. Advisory Circular (AC) 23-8A may be ordered from the Superintendent of Documents, U. S. Government Printing Office, Washington, D.C. 20402 or from any of the Government Printing Office bookstores located in major cities throughout the United States.

3. .BACKGROUND. This AC is the result of a cooperative effort of Experimental Aircraft Association (EAA), the Sport Airplane Manufacturers Association (SAMA), operators of these airplanes, and the Federal Aviation Administration (FAA). It was proposed to the FAA that the requirements of the Joint Aviation Requirements - Very Light Aircraft (JAR-VLA) as instituted by the Joint Airworthiness Authorities (JAA) on April 26, 1990, wouid provide an equivalent level of safety to the applicable requirements of part 23 as amended by amendment 23-42. In response to this proposal, the FAA reviewed the requirements of the JAR-VLA and the applicabie portions of this amendment of part 23. During this review, the FAA found that there are 225 sections of part 23 that are considered appropriate for very light airplanes." The JAR-VLA regulatory sections were essentially the same as 204 of these sections. The other 21 sections were found to be either absent from JAR-VLA or substantively different. A detailed analysis was conducted

12/2/92 AC 23-11

regarding the level of safety imposed by the 204 sections of part 23 and the corresponding requirements of JAR-VLA. It was determined that the requirements of JAR-VLA could be used to make a finding of equivalency to the corresponding part 23 requirements. Therefore, the JAR-VLA requirements plus certain additional part 23 requirements can be used as the certification basis for very light airplanes. This will ensure that the level of safety envisaged by part 23 will be attained. In a like manner, where. a particular section of part 23 did not have a corresponding JAR-viA requirement, it was determined that either the applicable part 23 requirement could be complied with or the exemption process could be pursued. Thus, literal compliance with each applicable section of part 23 will be achieved.

4. AIRPLANE TYPE CERTIFICATION PROCEDURES.

a. Application. Application for type certification must be made in accordance with the requirements of § 21.15. It was recommended that application be made to the Aircraft Certification Office (Aco) having geographic responsibility for the business location of the applicant or where the majority of ground and flight testing wiii be completed. Applicants based in the U.s. are, however, free to make application to any other Aco within the U.S. considered by the applicant to be to his or her advantage. In making the choice to apply to an Aco other than the one closest to the applicant, the applicant should consider the difficulties that may later be encountered in obtaining a production certificate (PC) or an approved production inspection system (APIs) for the production of individual airplanes.

The Small Airplane Directorate has been assigned the national technical policy standardization functions concerning the use of JAR-VLA in the U.S. The FAA engineers and flight test pilots from either the Small Airplane Directorate or the Chicago ACo may participate at their discretion in very light airplane type certification projects underway in other Aco's to provide advice on the application of the JAR-VLA, and to promote national standardization in the application of those criteria.

b. LATER AMENDMENTS TO THE REOUIREMENTS. It should be noted that future amendments of part 23 and/or JAR-VLA will be evaluated for applicability to the certification of these airplanes. Judgments that a new or amended part 23 section is applicable or not applicable will be made by weighing each with the level of safety that is appropriate for these airplanes. Those changes that unnecessarily raise the level of safety will be identified as such and discussed in subsequent revisions of appendix 2. Changes that are determined to be appropriate will, in a like manner, be addressed in subsequent revisions of appendix 2 or other applicable appendixes to this AC.

AC 23-11 12/2/92

5. APPLICABILITY. This AC is applicable to the type certification of single engine, two-place airplanes with a maximum gross weight of no more than i654 pounds (750 kg) and a power-off stall speed of no more than 45 knots CAS in the landing configuration at maximum weight. This AC is also limited to airplanes having powerplants and propellers that are type certificated to the requirements of parts 33 and 35 of the FAR.

6. OPERATIONAL LIMITATIONS. Airplanes showing compliance to part 23 via the requirements of JAR-VLÀ are limited to day-visual flight rules (VFR) operations unless the applicable equipment is installed and the requirements of part 23 related to night and instrument flight rules (IFR) operations are complied with. (These requirements are contained in appendix 4.) The operation of these airplanes is limited to normal category maneuvers and is limited to part 91 operations. The type certificate data sheet should reflect these limitations.

7. APPENDIXES. Since it is possible that some of the initial applicants will be unfamiliar with the type certification process, appendix 1 has been developed to provide guidance in this area. Also, appendix 2 has been provided to list the applicable part 23 sections where the corresponding JAR-VLA requirements were found not to be in full agreement or absent altogether and provides a discussion of the substantive differences that exist between part 23 and JAR-VLA. The logic contained in appendix 2 may be used as a basis to develop any needed findings of equivalency. Appendix 3 is included to provide a copy of the JAR-VLA requirements."It is envisioned that these appendixes will be expanded as future amendments of part 23 and JAR-VLA are adopted. Appendix 4 lists the part 23 requirements that could be imposed for IFR and/or night operation.

8. TYPE CERTIFICATION DATA SHEET (TCDS). The TCDS will reflect a certification basis of part 23 (applicable amendment) and any other requirements (special conditions, exemptions, etc.). Also to be included is a notation stating, "Findings of Equivalent Level of Safety," followed by/the,particular part 23 sections concerned.

BARRY D./CLEMENT Manager,/Small Airplane Directorate Aircraft Certification Service

AC 23-11 12/2/92 Appendix 1

APPENDIX 1. AIRCRAFT TYPE CERTIFICATION OVERVIEW

APPENDIX 1. AIRCRAFT TYPE CERTIFICATION OVERVIEW

1. INTRODUCTION. The time necessary to get an approval varies with the complexity of the design. The applicant should plan inspections, meetings, and tests well in advance to provide .FAA sufficient time to schedule their activities. When the schedule cannot be met, the applicant should try to minimize delays and keep the FAA informed. Flight testing is especially critical because of the added complication of weather.

The applicant design team will be responsible for generating the necessary data for a TC. Compliance data consist of all the supporting data necessary to show compliance with certification rules. Typical examples include the compliance checklist, structural loads reports, stress analysis, failure analysis, test reports, etc. All data necessary to support the TC application must be provided to the FAA for review."A copy will be retained in the FAA files. However, all data ‘are the property of the applicant and cannot be disclosed outside the FAÀ without the owner's written permission.

a. Certification Basis. Each certification project has associated with it a certification basis. This is a list of the Certification Rules, or other certification requirements approved by the Administrator with which the project must show compliance. The certification basis becomes the subject of issue paper G-l, which is developed by the Project Manager and routed to the Small Airplane Certification Directorate for final approval in accordance with Order 8100.5, "Aircraft Certification Directorate Procedures."

b. Use of Designees. The FAA has established a system of approved designees who are authorized to approve or to recommend approval of certain types of data that comply with the FAR or CAR.

The designee system provides an avenue by which an applicant can hire an engineer or inspector to perform on a timely basis a task that an FAA employee would normally perform. Because the system was established for the convenience of the applicant, the applicant must bear the cost of the designee's services. The FAA maintains current lists of designees. Designated Engineering Representatives (DER's) are listed in Advisory Circular (AC) i83.29-lZ. Note the DER's are approved by specific technical specialty, such as airframe, systems, equipment, propulsion, or flight test. Designated Àirworthiness Representatives (DAR's) are listed in AC 183.35B.

The FAA is required to audit the work of all DER's on a continuing basis." Generally this interchange takes place directly between the DER and the FAA. However, when the DER's

AC 23-11 Appendix 1 12/2/92

work is submitted by a third party, the FAA will refer the items needing corrections to that party. To facilitate the necessary communication when a DER is invoived, the FAA recommends frequent direct contact between the DER and the ACO, as well as between the applicant and the DER. The applicant's schedule should allow for the required FAA review of DER submittals.

Flight test pilots and flight analyst designees are required to contact the FAA Flight Test pilot prior to the initiation of an official FAA flight test program.

A Designated Airworthiness Representative (DAR) may perform examinations, inspections (including conformity inspections), and testing services in support of engineering and manufacturing. The DAR may perform these functions at any authorized location.

c. Inspections. Two types of inspections are required during TC programs. The compliance inspection is generally performed by an engineer or flight test pilot and is aimed at verifying that the design, such as the width of an aisle, complies with applicable regulations. The conformity inspection is performed by an inspector to verify that the article or installation conforms to the applicant's descriptive data.

Compliance inspections will be arranged by the applicant's FAA project engineer as necessary. Either the applicant or a representative should be present to answer questions and to arrange modifications if necessary.

Conformity inspections are arranged as necessary to ensure that the test articles are built in accordance with engineering data. In the case of long lead time items built in a remote location, it may be necessary to perform conformity inspections at the remote location of the vendor. Parts conformity inspections should be requested prior to assembly to avoid problems. The applicant should work closely with the FAA engineer to determine when a conformity inspection is required. The engineer will then request that the Manufacturing Inspection District Office (MIDO) perform the inspection. The MIDO will then contact the applicant to arrange the inspection. In the case of progressive conformity inspections, the engineer may ask the applicant to contact the MIDO directly. The applicant will be expected to identify the required data and to provide copies for the inspector. The applicant must conduct a conformity inspection prior to the official FAA inspection to ensure that the parts were manufactured and/or installed in accordance with the most recent FAA reviewed revision of the descriptive data. The applicant signifies this by signing a Statement of Conformity, FAA Form 8130-9. Any deviations must be listed on this form.

AC 23-11 12/2/92 Appendix 1

The Type Inspection Authorization (TIA) will specify certain ground tests and inspections to be performed, as weil as the required flight tests. It will also require that the applicant submit a Statement of Conformity, FAA Form 8130-9, stating that the applicant has inspected the article and that it corresponds to the design data. The FAA inspector will then conduct conformity.

d. Certification. Any data used to demonstrate compliance must be created and organized by the applicant. When complete, these data are submitted to the FAA for review and approval. A copy of the applicant's data remains on file with the FAA or may be stored at the applicant's facility as authorized by the FAA. Required data submittals can be divided into two major categories; descriptive data and substantiation, or compliance, data.

All data submitted must be identified. This includes a title, drawing or report number, date, and applicant's name. Each page of a report should contain enough of this information for complete identification.

(1) Descriptive Data. The descriptive data package must completely describe the fabrication, assembly, and installation of all portions of the aircraft. The descriptive data required to meet this standard include the engineering drawings, process specifications, material specifications, and other data necessary for fabrication of all parts and assemblies. This material .should define materials, manufacturing processes, and manufacturing tolerances. In addition, installation drawings and/or installation instructions must be prepared. All descriptive data must be prepared in accordance with standard industry practice and must be complete and accurate. Typical technical information required on drawings includes applicable process and material specifications, dimensions including tolerances, fasteners used and location, hardware used and locations, manufacturer and part numbers of purchased parts, placards, markings, weight and balance data, etc:

In addition, the descriptive data must completely define the design of all purchased equipment or components." If the item is TSO approved, the nameplate data may be adequate. Other equipment may require a source control drawing identifying the equipment by manufacturer, part number, drawing number and revision level, or any other necessary data.

(i) Specifications. The specifications necessary for production of parts are a part of any descriptive data package. These specifications include materials and processes. Certain accepted standard specifications can be used, or the applicant may develop its own specifications. Accepted standards

AC 23-11 Appendix 1 12/2/92

inciude various U.S. Government specifications (i.e., AN, MS, NAs, etc.) and various industry standards such as the American Society of Testing and Materials (ASTM) and the Society of Automotive Engineers (SAE) aerospace standards. A copy of each specification should be supplied as part of the applicant's descriptive data package.

Some processes, such as fiberglass lay-up, may require the applicant to develop a specification. Some of the items which may be covered include a complete and unambiguous definition of the materials to be used, detailed procedures, shelf life, and critical processing temperatures, times, etc., inspection criteria, rework limits, etc. A review of these specifications by the appropriate Manufacturing Inspection District Office (MIDO) may be necessary.

(ii) Drawings. The drawing system should be arranged so that drawing numbers follow some logical pattern. For example:

60000 - Final Installation 60100 - Major Assembly 60101 - Detail 60102 - Detail 60200 - Major Assembly, etc.

As many levels as necessary can be used. Each drawing should include approval date and revision level data so that FAA approval status can be easily verified. Each revision level should identify the changes made and revision date. These items should be reflected in the Drawing List submitted for FAA approval with the drawing package.

All drawings should conform to good drawing practice, including tolerances for all dimensions. All drawings should be thoroughly checked prior to submittal. If errors are discovered during necessary drawing review, the drawing package may be returned with a note that drawing quality is unacceptable. Where mistakes are found, the error wiil be indicated, but other errors may be present and; therefore, the applicant will be expected to review the entire package for other possible errors and resubmit the drawings.

Figures 1, 2, and 3 are examples of the various drawings that could be found in a data package for a very simple installation. This very simple package shows one way of meeting drawing package requirements. Note that the fictional company has developed its own process specifications for plating and inspection. These, as well as the installation instructions, are included in the drawing list.

AC 23-11 12/2/92 Appendix 1

This drawing list, or by reference to an installation instruction numbered document, is aiso divided into installation and manufacturing data. A revision control page is shown, but may not be needed on a very short drawing list.

While figures 1, 2, and 3 are examples of very simple drawings, they serve to illustrate the type of information required on drawings of various types and are an acceptable way of organizing a drawing system. Figure 4 is an example of a three-view drawing that wili be part of the documentation required for a type certification application.

2. SUBSTANTIATING (COMPLIANCE) DATA.Substantiating or compliance data are those data in addition to descriptive data necessary to show compliance with the regulations comprising the certification basis for the project. Compliance includes compliance checklists (recommended for complex programs), analyses, test proposals, test reports, letters from manufacturers, and instructions for operations.

One of the more helpful and highly recommended documents, the compliance checklist, lists each applicable certification rule and the method by which compliance will be shown (e.g. analysis, ground test, flight test). The compliance checklist is prepared by the applicant after the certification basis is identified. Each rule should be examined for applicability to the TC program. Those which are applicable must be so identified and a method of showing compliance identified. The checklist is continuously updated to identify reports, letters, tests, etc., that are used to show compliance.

A "basic loads analysis" is necessary. As the name implies, this report establishes the applied loads which the airplane must withstand (flight, ground, landing, etc.). These loads are determined from weight, power, and.aerodynamic characteristics of the aircraft using design speeds, load factors, and factors of safety specified in the applicant's certification basis. These loads form the foundation for later stress analysis.

"Stress analysis" is the term used to describe the substantiating data which establishes mathematically that the appropriate structural strength requirements have been met. The analysis builds on the basic loads data and "material allowables" data. Material allowables are safe loads established for the material. For metallic materials, the use of MIL-HDBK-5 data is recommended (other data may be acceptable). Non-metallic materials may require that the applicant develop allowables data. Stress analysis may include static stress analysis, fatigue, fail safe analysis, etc.

NOTES: Figu 1. ALT MAT'L THICKNESS.063

REVISIONS A MAT'L WAS AL 3O. FIN.WAS ZINC CHANGES BY DATE Appendix AC 23-11

2. ALT FIN. EPOXY PER SPBC. AAC4I

2. ALT FIN. EPOXY PER SPBC. AAC4I

3. SCALE : FULL SIZE 5

.50 RAD

0a5 SYH .500 DIA 2.25 HOLE

B ADDED ZINLCHROMATE IN FIN.BOCK SAH

1.75

SAMPLE PART FABRICATION DETAIL DRAWING TH.50 2.25 4.75

.25 RAD. .885 .250 DIA.HOLE (2PLACES)

1.00

16

PART NO ACME -1 050x2011d SIZE BRACKET 2024-T3 AL.SHT: DBSCAIPTION QQ-A-250/4 SPEC

BOXI NOWHERE, ARK. AIRCRAFT CORP. FLAP HINGE WING 7059406 8 B 9

BOXI NOWHERE, ARK. AIRCRAFT CORP. FLAP HINGE WING 7059406 8 B 9

13 FIN: DRW.N.S VINYL WASH 11/10/07 TOL.XxI.03 xxy-±.00 x±1 CHK S.M. 11/12/07 NPPR. J.K. 0/2/00 12

12/2/92

NOTES: 1. MASK OUT BEARING PRIOR TO FINISH OPERATION 2. SCALE ~ FULL SIZE

Fiqure

MATCH DRILL #30,7 PLACES, ANÁ70AD4-5 B RINET 7 REQ'D.

SAMPLE ASSEMBLY/SUB-ASSEMBLY DRAWING

SAMPLE ASSEMBLY/SUB-ASSEMBLY DRAWING

REVISIONS A 30 HOLE WAS CHANGES N.S. BY 1/0/ DATE 12/2/92

→A PRESS FIT N4B BBARING, STAKE + PLACES EQUALLY SPACED, BOTH SIDES

.25 (TYP)

(TYP)

.50 -A C

-705946 BRACKET(2REQ)

SECTION A-A

R S

N4B BEARING-HEIM COHHERCIAL 7 AN4-70 AD4-5 RIVET 2 705946 BRACKET PART NO. SIZE DESCRIPTION SPEC ACME ASSEMBLYT H AIRCRAFT CORP HIN GE BRACKET 705947 A BOX I NOWHERE, AK. FLAP

SECTION A-A

M FIN: VINYL WASH DRW. M.S 1/11/87 T0L.xxt.03, xxy•.010,rsx=1*6norc0 CHK. SH1/14/87 APP snn 1/17/87 Appendix 1 AC 23-11

8 AC NOTES: 1. JIG ALIGN HINGE BRACKETS PRIOR TO REVISIONS CHANGES BY DATE Appendix t 23-11

MARKING AND DRILLING SPAR 1 A ADDED NOTES 34 JO2

Figu 3. LEFT WING INSTALLATION SHOWN 2. THIS INSTALLATION APPLICABLE TO LEADSLED MODELS LS-I, LS-IA,LS-IB PER STC"SA70000NP 76.5 STA 2 STA +1..5 STA 6.5 RIGH WNG OPPOSIT 4. DRAWING NO TO SCALE

MARKING AND DRILLING SPAR 1 A ADDED NOTES 34 JO2

SAMPLE INST DETAIL A (TYP 3 PLACES) 3 -705947 BRACKET REAR SPAR WING STA.

0.0 HINGE TOP VIEW-LEFT WING

SPAR 19 ATION DRAWING 1.50 12 24 12 3 AN365-128 AN960-10 AN4-6A 705947 WASHER BOLT BRACKET ASS'YS NUT

PART NO. SIZE DISCRIPTION SPEC EACH BRACKET 705947 .2571.005 DIA 4 PLACES MATCH DRILL SPAR WITH PN BOXI NOWHERE,AK AIRCRAFT CORPHINGE BRACKETS ACME INSTALLATION FLAP 705948 A

0.0 HINGE TOP VIEW-LEFT WING

AN4-6A BOLT,12 REQD AN365-420NUT.12REQ'D. AN96O-10 WASHER,24 REQ'D 2 DRW. M.S 1/20/87 FIN: CHK. SM 1/21/87 TOL.Xx1.0, ×xX1.010 x11 APPD. J.K 1/22/17 OP. HOTED 13 12/2/92

12/2/92 AC 23-11 Appendix 1

FigUre 4 - SAMPLE THREE-VIEW DRAWING

AC 23-11 12/2/92 Appendix 1

The applicant must assure that the analytical methods and assumptions used are applicable, that all pertinent loading conditions have been addressed, and that margins of safety greater than or equal to zero have been shown for all structural elements.

Computer programs may be used to analyze structures, but must be approved by the FAA for each case. These programs require the operator to define a computer model of the structure to be analyzed. This model is then subjected to the program's analysis routines. It is necessary that each model be verified. This is generally accomplished by subjecting the structure being analyzed to limited load tests to verify model predictions. Both stress and deflection results must reasonably match. Other verification methods may be possible when agreed to by the FAA project engineer.

Failure analyses may be required for aircraft systems. This type of analysis is aimed at determining the effect on the aircraft of any single fault in the system. In addition, if a fault is undetectable or is identified as a latent failure, it must be presumed to exist at the same time as each other single fault.

3. TEST REPORTS. Test plans and reports must be prepared for each required ground and flight test. The test plans should include inspection requirements and must be submitted to the FAA for approvai prior to testing.

All parts and assemblies which have experienced permanent deformation or fracture during structural testing must be clearly and permanently identified to prevent use in a flight article. Parts and assemblies which have not been subjected to permanent deformation or fracture may be used as flight articles if the structural examinations required after test reveal no damage and the detailed part or. assembly still conforms to the type design.

4. FLIGHT TESTING. Flights tests are an important part of the process of type certification. Section 21.35 requires, in part, that the applicant make flight tests and report the results of the flight tests prior to official FAA Type Inspection Authorization (TIA) testing. After the applicant has submitted sufficient data to the FAA showing that compliance can be met, the FAA will conduct any inspections, flight, or ground tests required to verify the applicant's test resuits and determine that all requirements are met: Successful completion of the TIA tests by the FAA is one of the major steps toward TC issuance.

Research and development flight tests are performed by the applicant for his own testing. The FAA will neither participate in nor witness these tests. In order that such tests can be made

12/2/92 AC 23-11 Appendix 1

meaningful and safe, however, contact with FAA personnel for a general discussion of the tests is appropriate. Alternatively, the applicant may hire a Flight Test Pilot DER to perform developmental tests.

The applicant has the responsibility to prepare a certification flight test proposal. This proposal must be based on the certification basis and include recommended tests, instrumentation to be used, necessary safety equipment, data acquisition methods, and data reduction methods. The applicant should contact FAA flight test personnel to assure that the required test methods and criteria are understood and that potential hazards are recognized. If a DER pilot is employed, the DER must contact the FAA.

When the flight test report is received by the FAA, it will be reviewed. Those tests necessary to verify compliance with the certification rules will be identified and may be repeated by an FAA pilot. Prior to FAA test of the aircraft, the FAA will perform a conformity inspection to ensure that the aircraft conforms to the design data. If discrepancies are found, the applicant may be required to correct the discrepancies and repeat any tests which could have been influenced by the non-conformity before the FAA will perform required tests.

The applicant is responsible for providing flight test ballast and adequate means for securing it. It is extremely important that ballast be securely restrained. Loose ballast may damage aircraft structure, jam controls, or otherwise render an aircraft uncontrollable. Ballast must be restrained in such a manner as to withstand the inertial loads resulting from a survivable emergency landing. The preferred form for ballast is small, sturdy canvas or leather bags of shot. These are easily moved, take minimum space, and can be readily secured. Use of passengers as ballast is not acceptable.

5. CERTIFICATION PROCESS.

a. Pre-Application Activities. The applicant will need to develop a Certification Program Plan that outlines an efficient type certification program for the design. A certification program plan is required and should address all applicable requirements. The following activities should be accomplished by the applicant before the type certification application is filed:

(1) Determine the proposed certification basis.

(2) Perform sufficient analysis, possibly with a wind tunnel modei or a mockup airplane, or buiid an R&D prototype airplane and perform such analysis and preliminary testing to determine compliance with certification basis standards to minimize modification during the certification program.

AC 23-11 12/2/92 Appendix 1

(3) For long lead time items, the applicant should develop a. plan to address conformity inspections of purchased parts before the TC application is filed.

(4) Prepare, usually in very preliminary form, the following documents for presentation at the Preliminary Type Board Meeting:

(i) Certification Basis. The certification basis to be proposed to the FAA should be determined. This will be applicable sections of the FAR through the current amendment at time of type certification application. For unconventional configurations or materials, special conditions and equivalent level of safety findings should be processed in accordance with Order 8110.4, "Type Certification," and Order 8100.5, "Aircraft Certification Directorate Procedures."

(ii) Compliance Checklist. A compliance checklist is developed and should identify each applicable requirement of the certification basis and indicate the methods of compliance, (i.e., by drawing, analysis, test, or a combination of these methods) proposed for each requirement.

(iii) Certification Compliance Plan. A plan developed from the Certification Program is prepared to coordinate scheduling of FAA activities.

(iv) Documentation. The drawing package, a three view drawing, drawing lists, and detailed drawings specifying the design and including materials and process specifications, should be prepared.

(v) Analyses. All analyses used to develop the design will be documented by engineering reports to substantiate certification requirements. Prior to initiating detailed designs, the applicable regulations pertaining to that design shouid be studied for incorporation into the design. This step is important as it should improve the possibility of compliance during certification program.

(vi) Test Program Plan. A proposed test program plan, including a schedule specifying when and how all testing will be done (for structures, powerplants, systems and flight tests), including proposed report forms shouid be developed.

(vii) Supplier List. Component suppliers with the part numbers, descriptions and the data furnished by the supplier with the applicant's purchase order should be listed.

(viii) Conformity Inspection Plan. The conformity inspection plan, as specified in a Conformity Manual.

12.

12/2/92 AC 23-11 Appendix 1

b. Certification Program. A chart that shows the timetable of the major activities involved in a small airplane type certification program should be developed. The major milestones are listed in the general order of occurrence and are described below:

(1) Application. Application is initiated with submittal of an application letter and a completed "Application for Type Certificate, Production Certificate, or Supplemental Type Certificate," FAA Form 8110-12, to the local ACO. The application shouid also include a three-view drawing, and general specifications. Upon initiation of the project in the Aco, a certification team will be formed representing engineering, flight test, manufacturing inspection, and project aircraft evaluation group personnei. The Smali Airpiane Directorate Project Officer will normally serve as a team member in a consulting role to the ACo project team in accordance with Order 8100.5.

(2) Preliminary Type Board or Aircraft Familiarization Meeting. The applicant will brief the Aco and Directorate personnel on the general design features and propose the certification basis, certification program plan, and the test program. The FAA reviews the proposed certification basis, identifies areas where issue papers including safety equivalences are needed, and identifies the need for any special conditions. The applicant and FAA (MIDO) should then reach agreement on a conformity inspection plan before construction of the structural test articles or the test article airplane. The Preliminary Type Board meeting should be conducted and minutes of the meeting should be prepared in accordance with Type Certification Order 8110.4.

(3) Conformity Test Articles. The applicant builds structural test articles and a test article airplane. The detail parts and sub-assemblies of the structure (wing, load bearing structure, empennage, landing gear, etc.) to be used in static/structural test programs must conform to the type design, including materials and process specifications.It is essential that drawings and quality assurance records are kept current and documented to show conformity of the test articles to type design at any point in the certification program. The need to show conformity to type design for certification tests also applies to the prototype flight test airplanes as the test program progresses. The validity of previous test data must be substantiated for changes made to the type design during the certification program or affected tests may have to be repeated.

(4) Test Program. The FAA monitors the test program and witnesses critical tests. Prototype conformity inspections occur throughout the program and should precede any test witnessed by the FAA.

AC 23-11 12/2/92 Appendix 1

(5) Preflight Board Meeting. Once the aircraft is structurally substantiated and the applicant has investigated the flight envelope for compliance, the FAA and applicant meet to resolve items from earlier Type Certification board meeting minutes and outstanding issues. Major items and issues must be resolved prior to issuance of the Type Inspection Authorization (TIA), and the flight test schedule. At this point, the applicant has finalized the design, and the conformity inspections of test articles to the drawing package are complete. Issue papers and Board Meeting Minutes open items are closed, or resolutions are agreed upon. Issue papers are to be processed in accordance with FAA Aircraft Certification Directorate Procedures Order 8100.5.

The limitations section of the instructions for continued airworthiness (in the flight manual) should be drafted and available for FAA review.

(6) FAA Flight Tests. The certification flight testing is done in accordance with the TIA requirements and Advisory Circular 23-8A. The FAA will develop the type inspection report (TIR), verifying and approving all limitations, emergency, abnormal operations, and performance data, and the AFM. The ACo and the Aircraft Evaluation Group will review the maintenance manual for approval when available. The FAA will assist the Environmental Protection Agency in approving the noise certification.

The applicant develops the draft Type Certification Data Sheets (TCDS) for FAA review and approval.

(7) Final Type Board Meeting. The FAA will issue the Type Certificate and an advance copy of TCDs. The limitations section of the maintenance manuals are FAA approved and the remaining manuals are FAA accepted when available (not required for the final type board meeting)..

AC 23-11 12/2/92 Appendix 2

APPENDIX 2. COMPARISON OF PART 23 (AMENDMENT 23-42) OF THE FAR AND JAR-VLA (DATED APRIL 26, 1990, AMENDED JANUARY 1, 1992)

A comparison of the sections of part 23 that could form the basis to develop equivalent level of safety findings are listed below. Each airplane design will need to be evaluated on its own merits to determine if any or all of these sections are appropriate for these findings when coupled with any additional certification requirements deemed necessary to provide the level of safety of the relevant section of part 23. If no VLA rule comparable to a part 23 section exists, the airplane design will need to comply with the applicable part 23 rule.

§ 23.45 Performance - This section requires the airplane performance to be corrected for atmospheric, humidity, and installation losses. The installation losses consist of induction system, exhaust system, and accessory load. The total losses of the induction system, exhaust system and most accessories are present during the performance testing. Only the alternator load is a variable, totaling a normal maximum of one-half horsepower. Likewise, the typical humidity on test-suitable days is in the 40% to 50% range, yielding a majority of the correction loss during the tests. The maximum performance error possible by accepting demonstrated performance versus computation corrections is less than 10 fpm climb rate or 10 ft. of take-off distance. These amounts are not significant in flight planning for this class of aircraft, a fact readily demonstrated by the thousands of similar airplanes flying today without any performance information provided by the manufacturer.

§ 23.77 Balked Landing - This section requires a steady angle of climb at sea level of at least i:30 in the landing configuration with full power. JAR-VLA 77 requires the identical performance, or an absolute ceiling of 3000' at the balked landing transition speed. First, one should recognize that the 3000' absolute ceiling occurs at the balk landing transition speed which is considerably below the best rate of climb speed. Secondly, a parametric study shows that even extreme configurations meet both requirements, i.e., 500 pound Gw, 20 knot v and 10 hp; 1000 pound GW, 30 knot v and 25 hp; i500 pound GW, 40 knot V, 50 hp airplanes each have a sea level climb gradient of 1:30 and a 3000' absolute ceiling at balked landing speed. This study illustrates that the 3000' absolute ceiling criteria is not necessarily the limiting criteria within the scope of usable airplanes.

AC 23-11 12/2/92 Appendix 2

§ 23.145 Longitudinal Control - This section requires the airplane be safely brought to level flight at an attitude suitable for landing without using the elevator primary control. Power, gear, flaps, and trim may be used to execute the maneuver. The condition creating this requirement is being able to land with the elevator control disconnected but not jammed. JAR-VLA requires an actual flight from take-off to landing, but allows use of the elevator primary control, power, gear, and flaps while the elevator trim is set at the extremes. The presumption creating this requirement is being able to complete a flight with elevator tab control disconnected or jammed and the tab at the most adverse location. Each code addresses failure in the elevator control system but selects different failures for demonstration. While it is possible for each failure to occur, the probability of trim system failure and/or jamming may be higher than elevator control system failure without jamming.

§ 23.561 Emergency Landing Conditions, General - This section and JAR-VLA 561 both require occupant restraint of 3g upward, 9g forward and 1.5g sideward. Section 23.561 requires cabin masses to be restrained 3g upward, 18g forward, and 4.5g sideward while JAR-VLA requires cabin mass restraint equal to occupant restraint. JAR-VLA requires engines located aft and above the cabin to be restrained 15g forward. There would appear to be some occupant protection provided by the additional restraint for cabin mass and aft engine. However, we should recognize that for a cabin mass or engine to be potentially harmful, it must be upstream of the occupant from the point of impact. Test results have verified that crash loads diminish proportionally with distance upstream of the impact. This phenomenon has since been verified by NASA and NTSB tests and investigations. Consequently, any potentially harmful mass located aft should experience a lesser load than the target occupant. With both the occupants and masses designed to the same criteria, impact forces would cause the occupant to break loose first, or at least simultaneously.

§ 23.562 Emergency Landing Dynamic Conditions - The most predominate factor in an impact is velocity; severity being a function of (velocity)'. Airplane accidents can broadly be put into three categories: 1) Cruise (mountain side, mid-air, totally uncontrolled descent, etc.): essentially unsurvivable. 2) Controlled (pattern stall, short landing, unprepared area landing, etc.): usually severe but survivable. 3) Ground (tug collision, blow over, roll-out control loss, etc.): modest. There is no known technology available that would have any measurable affect on the

12/2/92 AC 23-11 Appendix 2

survivability of category 1) accidents. Category 3) accidents are sufficiently modest that little protection is needed. Consequently, when one speaks of survivability and crash protection, it is related generally to category 2).

Category 2) crash severity has a close relationship to (stail speed)', as evidenced by NTSB crash studies and AOPA Safety Foundation crash analysis. Part 23 certified airplanes have stall speeds ranging approximately from 30 knots to 100 knots, giving a crash severity ratio of 11:1 (10,000/900). Section 23.562 imposes a constant absorption and restraint criteria for all aircraft, totally overlooking the predominate variable of stall speed.

When the rulemaking allowing single engine stall speeds above 61 knots was undertaken, the aforementioned oversight was recognized by determining the existing protection level resulting from 6l knot stall speed and requiring additional protection based on (stall speed)' would be required for higher speeds.

Calculation of v versus severity ratio, determines that a stall speed of 45 knots may result in an impact severity below the onset of protection provided by § 23.562.

§ 23.572 Wing, Empennage, and Associated Structures - This section requires a life determination for critical structure in the wing and empennage. JAR-VLA provides maximum allowable design stresses that provide critical structure life exceeding the utilization life of this class airplane. This approach to airplane life determination could be considered.

5 23.629 Flutter - This section addresses turboprop flutter requirements and flutter requirements for flight speeds above 260 knots, neither of which are applicable to, or included in, JAR-VLA 629. Section 23.629(a)(2) requires a ground vibration test, while allowing the fiutter substantiation to be done by analysis, flight test, or compliance to pages 4-12 in Airframe and Equipment Engineering Report No. 45. Substantiation by flight test does not require a ground vibration test (GvT) and substantiation by report No. 45 provides alternate means of determining the critical frequencies. JAR-VLA 629 recognizes this irregularity and permits flutter

AC 23-11 12/2/92 Appendix 2

substantiation of airplanes having V, = 140 knots or less by utilizing report No. 45 and flight test, but foregoing the GVT.

§ 23.677 Trim Systems - See 23.145 (identical issue)

§ 23.733 Tires - This section requires the nose tire dynamic rating of 131% of the maximum static load, while JAR-VLA requires 121% of maximum static load for the dynamic rating. The 10% reduction in dynamic rating is easily offset by the low landing speed required by JAR-VLA, in that dynamic stress on the tire is a function of (landing speed)'. The 16 knot lower stall speed, and resultant lower landing speed of JAR-VLA airplanes is significantly below the speed rating of Type III tires, the lowest performance airplane tire available. This characteristic and the lower dynamic forces involved do not compromise the level of safety appropriate for these airplanes and may provide adequate compensation.

§ 23.783 Doors - This section requires exits to be externally marked in a visually conspicuous manner. JAR-VLA is limited to one or two occupant cabins, and access and egress provisions are normally sufficiently visibly obvious as to make marking unnecessary.

5 23.807 Emergency Exits - This section requires an emergency exit opposite the primary door for airplanes with from two to ten place seating. Section 23.807 excludes from that requirement those airplanes with canopies. JAR-VLA requires only a cabin door; however, recognizing that FAR 23 permits up to 10 occupants, the 2-place maximum occupant limitation of VLA plus the light construction (and therefore ease of emergency egress) necessitated by the 1654 pound weight limitation can provide adequate compensation.

§ 23.965 Fuel Tank Tests - This section requires fuel tanks with large unsupported walls to be slosh and vibration tested, unproven construction or sealant to be vibration tested and bladder tanks to be slosh tested. A significant body of data from past certification programs has demonstrated that fuel tanks integral to principal flight load structure consistently pass the slosh and vibration test, and has verified a wide array of construction techniques, sealants and bladder materials. Continued reverification of these items is unnecessary. JAR-VLA continues the requirement to pressure test fuel tanks, but dispenses with the mandatory slosh and vibration testing. If questionable techniques or materials are presented for certification, the certifying engineer can require an appropriate verification assuring equivalency.

12/2/92 AC 23-11 Appendix 2

§ 23.971 Fuel Tank Sump - This section requires a fuel tank sump capacity of .25% of fuel tank capacity or 1/16 gallon (14.4 in'), whichever is larger, unless a drainable sediment bowl or chamber is provided with a capacity of 1 fl. oz. (1.84 in3) for every 20 gallons of fuel capacity. Maximum fuel quantities permitted are limited only by the 12,500 pound weight limit of FAR 23. JAR-VLA requires a fuel tank sump capacity of only.10% of tank capacity or 120 cm3 (7.3 in'), unless a drainable sediment bowl or chamber is provided with a capacity of 25 cm'(1.53 in3). Maximum fuel quantities of airplanes designed to JAR-VLA with the 1654 pound weight limit are significantly less than those of part 23 airplanes.

Fuel contamination quantities are historically proportional to the amount of fuel or fuel tank(s) displacement; i.e., the greater the fuel quantity taken on, or fuel tank displacement subject to moisture formation, the greater the amount of contamination accumulating. For the substantially smaller fuel capacity feasible within the 1654 pound weight limit of JAR-VLA, the lesser sump or sediment bowl/chamber capacity could provide adequate compensation.

§ 23.1309 Equipment, Systems, and Installations - JAR-VLA requires the equipment, systems, and installations must be designed to minimize hazards to the airplane in the event of a probable malfunction or failure. Section 23.1309 requirements are similar, but the rule is expanded to clarify the analytical process of determining how to minimize the hazard. All systems as identified by § 23.1309(f) must be assessed for their impact on the continued safe flight and landing of the airplane should that system fail.

In the event it can be determined by demonstration or analysis that no airplane system is critical or essential, the use of AC 23.1309-1A, dated June 3, 1992, figure 1, wil1 be sufficient to show compliance with the requirements of § 23.1309.

§ 23.1529 Instructions For Continued Airworthiness - This section invokes Appendix G to Part 23 which delineates content, format and some procedural guidance related to the Continued Airworthiness Manuals. JAR-VLA 1529·delineates the content, which covers the same material required by Appendix G, required for the Continued Airworthiness. JAR-VLA 1529 does not address format or procedural matters; however, this variance may be considered as an issue during the compliance of § 91.409, "Inspections."

5 (and 6)

12/2/92 Appendix 3 AC 23-11 Joint Aviation Requirements

JAR-VLA Very Light Aeroplanes

26 April 1990

26 April 1990

The members of the Joint Aviation Authorities Committee are representatives of the Civil Aviation Authorities of the countries that have signed the 'Arrangements Concerning the Development and the Acceptance of Joint Airworthiness Requirements'. A list of these countries is kept by Direction Generale de I'Aviation Civile (DGAC) 246, Rue Lecourbe, 75732 Paris, Cedex 15, France.*

Applications for further copies of the Joint Aviation Requirements should be addressed to the Civil Aviation Authority. Printing and Publication Services, Greville House, 37 Gratton Road, Cheltenham, Glos. GL50 2BN, England.

Enquiries regarding the contents should be addressed to the JAA Secretariat, Aviation House, Gatwick Airport, West Sussex, RH6 OYR.

These countries are: Austria, Beigium, Denmark, Finland, France, Germany, lta!y. Netherlands, Norway. Spain, Sweden, Switzerland & United Kingdom.

26.4.90 ii

(Revision)

Page ii

Amend the third paragraph and add a list of countries, as follows:-

The members of the Joint Aviation Authorities Committee are representatives of the Civil Aviation Authorities of the countries that have signed the 'Arrangements concerning the Development and the Acceptance of Joint Airworthiness Requirements'. A list of these countries is kept by the Direction Generale de l'Aviation Civile (DGAC), 246 rue Lecourbe, 75732 Paris, Cedex 15, France.

Applications for further copies of the Joint Aviation Requirements should be addressed to the Civil Aviation Authority, Printing and Publication Services, Greville House, 37 Gratton Road, Cheltenham, Glos. GL50 2BN, United Kingdom.

[Enquiries regarding the contents should be addressed to the JAA Headquarters, Saturnusstraat 10, P O Box 3000, 2130 KA Hoofddorp, The Netherlands.]

[•These countries are:

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy. Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom & Yugoslavia.]

(OP) ii Amendment VLA/92/1 Effective 1.1.92

INTENTIONALLY

LEFT

BLANK

(OP) C-1

CONTENTS (Layout)

JAR-VLA

VERY LIGHT AEROPLANES

VERY LIGHT AEROPLANES

FOREWORD

CHECK LIST OF PAGES

PREAMBLES

SECTION 1- REQUIREMENTS:

SUBPART A GENERAL SUBPART B FLIGHT SUBPART C STRUCTURE SUBPART D DESIGN AND CONSTRUCTION

SUBPART E POWERPLANT SUBPART F EQUIPMENT SUBPART G OPERATING LIMITATIONS AND INFORMATION

APPENDICES: A, B. C, F and H

SECTION 2 — ACCEPTABLE MEANS OF COMPLIANCE AND INTERPRETATIONS (ACJ)

SECTION 2 — ACCEPTABLE MEANS OF COMPLIANCE AND INTERPRETATIONS (ACJ)

CONTENTS (Details)

VERY LIGHT AEROPLANES

Paragraph

FOREWORD

CHECK LIST OF PAGES

PREAMBLES

SECTION 1 - REQUIREMENTS

General and Presentation

SUBPART A - GENERAL

JAR-VLA 1 Applicability JAR-VLA 3 Aeroplane Categories

SUBPART B - FLIGHT

SUBPART B - FLIGHT

GENERAL

JAR-VLA 21 Proof of compliance JAR-VLA 23 Load distribution limits JAR-VLA 25 Weight limits JAR-VLA 29 Empty weight and corresponding centre of gravity JAR-VLA 33 Propeller speed and pitch limits

PERFORMANCE

JAR-VLA 45 General JAR-VLA 49 Stalling speed JAR-VLA 51 Take-off JAR-VLA 65 Climb JAR-VLA 75 Landing JAR-VLA 77 Balked landing

FLIGHT CHARACTERISTICS

FLIGHT CHARACTERISTICS

JAR-VLA 141 General

CONTROLLABILITY AND MANOEUVRABILITY

JAR-VLA 143 General JAR-VLA 145 Longitudinal control JAR-VLA 153 Control during landings JAR-VLA 155 Elevator control forces in manoeuvres JAR-VLA 157 Rate of roll

Page

F-1

CL-1

P-1

1-0-1

1-A-1 1-A-1

1-B-1 1-B-1 1-B-1 1-B-1 1-B-2

1-B-2 1-B-2 1-B-2 1-B-3 1-B-3 1-B-3

1-B-2 1-B-2 1-B-2 1-B-3 1-B-3 1-B-3

1-B-3

1-B-3 1-B-3 1-B-4 1-B-4 1-B-4

Paragraph

TRIM

JAR-VLA 161 Trim

STABILITY

JAR-VLA 171 General JAR-VLA 173 Static longitudinal stability JAR-VLA 175 Demonstration of static longitudinal stability JAR-VLA 177 Static directional and lateral stability JAR-VLA 181 Dynamic stability

STALLS

JAR-VLA 201 Wings leve! stall JAR-VLA 203 Turning fight and accelerated stalls JAR-VLA 207 Stall warning

SPINNING

JAR-VLA 221 Spinning

Page

1-B-4

1-B-5 1-B-5 1-B-5 1-B-5 1-B-6

1-B-6 1-8-7 1-B-7

1-B-7

GROUND AND WATER HANDLING CHARACTERISTICS

GROUND AND WATER HANDLING CHARACTERISTICS

JAR-VLA 231 Longitudinal stability and control JAR-VLA 233 Directional stability and control JAR-VLA 235 Taxying condition JAR-VLA 239 Spray characteristics

MISCELLANEOUS FLIGHT REQUIREMENTS

JAR-VLA 251 Vibration and buffeting

SUBPART C - STRUCTURE

SUBPART C - STRUCTURE

GENERAL

JAR-VLA 301 Loads JAR-VLA 303 Factor of safety JAR-VLA 305 Strength and deformation JAR-VLA 307 Proof of structure

FLIGHT LOADS

JAR-VLA 321 General JAR-VLA 331 Symmetrical flight conditions JAR-VLA 333 Flight envelope JAR-VLA 335 Design airspeeds JAR-VLA 337 Limit manoeuvring load factors JAR-VLA 341 Gust losd factors JAR-VLA 345 High lift devices JAR-VLA 347 Unsymmetrical flight conditions JAR-VLA 349 Rolling conditions JAR-VLA 351 Yawing conditions JAR-VLA 361 Engine torque JAR-VLA 363 Side load on engine mount JAR-VLA 369 Special conditions for rear lift truss JAR-VLA 373 Speed control devices

FLIGHT LOADS

26.4.90 C-4

1-B-8 1-B-8 1-B-8 1-B-8

1-B-8

1-C-1 1-C-1 1-C-1 1-C-1

1-C-1 1-C-1 1-C-2 1-C-3 1-C-3 1-C-3 1-C-3 1-C-4 1-C-4 1-C-4 1-C-4 1-C-4 1-C-5 1-C-5

CONTENTS (Details)

VERY LIGHT AEROPLANES

Paragraph

FOREWORD

CHECK LIST OF PAGES

PREAMBLES

SECTION 1 - REQUIREMENTS

General and Presentation

SUBPART A — GENERAL

SUBPART A — GENERAL

JAR-VLA 1 Applicability JAR-VLA 3 Aeroplane Categories

SUBPART B - FLIGHT

GENERAL

JAR-VLA 21 Proof of compliance JAR-VLA 23 Load distribution limits JAR-VLA 25 Weight limits JAR-VLA 29 Empty weight and corresponding centre of gravity JAR-VLA 33 Propeller speed and pitch limits

SUBPART B - FLIGHT

PERFORMANCE

JAR-VLA 45 General JAR-VLA 49 Stalling speed JAR-VLA 51 Take-off JAR-VLA 65 Climb JAR-VLA 75 Landing JAR-VLA 77 Balked landing

FLIGHT CHARACTERISTICS

JAR-VLA 141 General

CONTROLLABILITY AND MANOEUVRABILITY

JAR-VLA 143 General JAR-VLA 145 Longitudinal control JAR-VLA 153 Control during landings JAR-VLA 155 Elevator control forces in manoeuvres JAR-VLA 157 Rate of roll

CONTROLLABILITY AND MANOEUVRABILITY

Page

F-1

CL-1

P-1

1-0-1

1-A-1 1-A-1

1-B-1 1-B-1 1-B-1 1-B-1 1-B-2

1-B-2 1-B-2 1-B-2 1-B-3 1-B-3 1-B-3

1-B-3

1-B-3 1-B-3 1-B-4 1-B-4 1-B-4

Paragraph

CONTROL SURFACE AND SYSTEM LOADS

JAR-VLA 391 Control surface loads JAR-VLA 395 Control system loads JAR-VLA 397 Limit control forces and torques JAR-VLA 399 Dual control systems JAR-VLA 405 Secondary control system JAR-VLA 407 Trim tab effects JAR-VLA 409 Tabs JAR-VLA 415 Ground gust conditions

HORIZONTAL TAIL SURFACES

HORIZONTAL TAIL SURFACES

JAR-VLA 421 Balancing loads JAR-VLA 423 Manoeuvring loads JAR-VLA 425 Gust loads JAR-VLA 427 Unsymmetrical loads

VERTICAL TAIL SURFACES

JAR-VLA 441 Manoeuvring loads JAR-VLA 443 Gust loads JAR-VLA 445 Outboard fins

SUPPLEMENTARY CONDITIONS FOR TAIL SURFACES

SUPPLEMENTARY CONDITIONS FOR TAIL SURFACES

JAR-VLA 447 Combined loads on tail surfaces JAR-VLA 449 Additional loads applicable to V-tails

AILERONS, WING FLAPS AND SPECIAL DEVICES

JAR-VLA 455 Ailerons JAR-VLA 457 Wing flaps JAR-VLA 459 Special devices

GROUND LOADS

JAR-VLA 471 General JAR-VLA 473 Ground load conditions and assumptions JAR-VLA 477 Landing gear arrangement JAR-VLA 479 Level landing conditions JAR-VLA 481 Tail-down landing conditions JAR-VLA 483 One-wheel landing conditions JAR-VLA 485 Side load conditions JAR-VLA 493 Braked roll conditions JAR-VLA 497 Supplementary conditions for tail wheels JAR-VLA 499 Supplementary conditions for nose wheels JAR-VLA 505 Supplementary conditions for ski-planes

WATER LOADS

WATER LOADS

JAR-VLA 521 Water load conditions

EMERGENCY LANDING CONDITIONS

JAR-VLA 561 General

FATIGUE EVALUATION

JAR-VLA 572 Parts of structure critical to safety

Page

1-C-5 1-C-5 1-C-5 1-C-6 1-C-6 1-C-6 1-C-6 1-C-6

1-C-6 1-C-6 1-C-8 1-C-8

1-C-8 1-C-9 1-C-9

1-C-9 1-C-10

1-C-10 1-C-10 1-C-10

1-C-10 1-C-10 1-C-11 1-C-11 1-C-11 1-C-11 1-C-11 1-C-11 1-C-12 1-C-12 1-C-12

1-C-10 1-C-10 1-C-11 1-C-11 1-C-11 1-C-11 1-C-11 1-C-11 1-C-12 1-C-12 1-C-12

1-C-12

1-C-12

1-C-13

Paragraph

Page

SUBPART D - DESIGN AND CONSTRUCTION

GENERAL

JAR-VLA 601 General JAR-VLA 603 Materials and workmanship JAR-VLA 605 Fabrication methods JAR-VLA 607 Self-locking nuts JAR-VLA 609 Protection of structure JAR-VLA 611 Accessibility JAR-VLA 613 Material strength properties and design values JAR-VLA 615 Design properties JAR-VLA 619 Special factors JAR-VLA 621 Casting factors JAR-VLA 623 Bearing factors JAR-VLA 625 Fitting factors JAR-VLA 627 Fatigue strength JAR-VLA 629 Flutter

SUBPART D - DESIGN AND CONSTRUCTION

WINGS

JAR-VLA 641 Proof of strength

CONTROL SURFACES

JAR-VLA 651 Proof of strength JAR-VLA 655 Installation JAR-VLA 657 Hinges JAR-VLA 659 Mass balance

CONTROL SYSTEMS

JAR-VLA 671 General JAR-VLA 673 Primary flight controls JAR-VLA 675 Stops JAR-VLA 677 Trim systems JAR-VLA 679 Control system locks JAR-VLA 681 Limit load static tests JAR-VLA 683 Operation tests JAR-VLA 685 Control system details JAR-VLA 687 Spring devices JAR-VLA 689 Cable systems JAR-VLA 693 Joints JAR-VLA 697 Wing flap controls JAR-VLA 699 Wing flap position indicator JAR-VLA 701 Flap interconnection

LANDING GEAR

LANDING GEAR

JAR-VLA 723 Shock absorption tests JAR-VLA.725 Limit drop tests JAR-VLA 726 Ground load dynamic tests JAR-VLA 727 Reserve energy absorption drop tests JAR-VLA 729 Landing gear extension and retraction system JAR-VLA 731 Wheels JAR-VLA 733 Tyres JAR-VLA 735 Brakes JAR-VLA 737 Skis

26.4.90 C-6

1-D-1 1-D-1 1-D-1 1-D-1 1-D-1 1-D-1 1-D-1 1-D-1 1-D-2 1-D-2 1-D-2 1-D-2 1-D-2 1-D-3

1-D-3

1-D-3 1-D-3 1-D-4 1-D-4

1-D4 1-D-4 1-D4 1-D-4 1-D-4 1-D4 1-D-5 1-D-5 1-D-5 1-D-5 1-D-5 1-D-5 1-D-6 1-D-6

1-D-6 1-D-6 1-D-7 1-D-7 1-D-7 1-D-8 1-D-8 1-D-8 1-D-8

1-D-6 1-D-6 1-D-7 1-D-7 1-D-7 1-D-8 1-D-8 1-D-8 1-D-8

Paragraph

FLOATS AND HULLS

JAR-VLA 751 Main float buoyancy JAR-VLA 753 Main fioat design JAR-VLA 757 Auxiliary floats

PERSONNEL AND CARGO ACCOMMODATIONS

JAR-VLA 771 Pilot compartment JAR-VLA 773 Pilot compartment view JAR-VLA 775 Windshields and windows JAR-VLA 777 Cockpit controls JAR-VLA 779 Motion and effect of cockpit controls JAR-VLA 781 Cockpit control knob shape JAR-VLA 783 Exits JAR-VLA 785 Seats, safety belts and harnesses JAR-VLA 787 Baggage compartments JAR-VLA 807 Emergency exits JAR-VLA 831 Ventilation

FIRE PROTECTION

FIRE PROTECTION

JAR-VLA 853 Compartment interiors JAR-VLA 857 Electrical bonding JAR-VLA 863 Flammable fiuid fire protection JAR-VLA 865 Fire protection of flight controls and other flight structure

MISCELLANEOUS

JAR-VLA 871 Levelling means

SUBPART E - POWERPLANT

GENERAL

JAR-VLA 901 Installation JAR-VLA 903 Engines JAR-VLA 905 Propellers JAR-VLA 907 Propeller vibration JAR-VLA 909 Superchargers JAR-VLA 925 Propelier clearance JAR-VLA 943 Negative acceleration

FUEL SYSTEM

FUEL SYSTEM

JAR-VLA 951 General JAR-VLA 955 Fuel flow JAR-VLA 957 Flow between interconnected tanks JAR-VLA 959 Unusable fuel supply JAR-VLA 961 Fuel system hot weather operation JAR-VLA 963 Fuel tanks: general JAR-VLA 965 Fuel tank tests JAR-VLA 967 Fuel tank installation JAR-VLA 969 Fuel tank expansion space JAR-VLA 971 Fuel tank sump JAR-VLA 973 Fuel tank filler connection JAR-VLA 975 Fuel tank vents and carburettor vapour vents JAR-VLA 977 Fuel strainer or filter

Page

1-D-9 1-D-9 1-D-9

1-D-9 1-D-9 1-D-9 1-D-9 1-D-10 1-D-11 1-D-11 1-D-11 1-D-12 1-D-12 1-D-12

1-D-9 1-D-9 1-D-9 1-D-9 1-D-10 1-D-11 1-D-11 1-D-11 1-D-12 1-D-12 1-D-12

1-D-12 1-D-13 1-D-13 1-D-13

1-D-13

1-E-1 1-E-1 1-E-1 1-E-1 1-E-1 1-E-1 1-E-2

1-E-2 1-E-2 1-E-2 1-E-3 1-E-3 1-E-3 1-E-3 1-E-3 1-E-4 1-E-4 1-E-4 1-E-4 1-E-4

Paragraph

FUEL SYSTEM COMPONENTS

JAR-VLA 991 Fuel pumps JAR-VLA 993 Fuel system lines and fittings JAR-VLA 995 Fuel valves and controls JAR-VLA 999 Fuel system drains

OIL SYSTEM

OIL SYSTEM

JAR-VLA 1011 General JAR-VLA 1013 Oil tanks JAR-VLA 1015 Oil tank tests JAR-VLA 1017 Oil lines and fittings JAR-VLA 1019 Oil strainer or filter JAR-VLA 1021 Oil system drains JAR-VLA 1023 Oil radiators

COOLING

JAR-VLA 1041 General JAR-VLA 1047 Cooling test procedure for reciprocating engine aeroplanes

LQUID COOLING

LQUID COOLING

JAR-VLA 1061 Installation JAR-VLA 1063 Coolant tank tests

INDUCTION SYSTEM

JAR-VLA 1091 Air induction JAR-VLA 1093 Induction system icing protection JAR-VLA 1101 Carburettor air preheater design JAR-VLA 1103 Induction system ducts JAR-VLA 1105 Induction system screens

EXHAUST SYSTEM

EXHAUST SYSTEM

JAR-VLA 1121 General JAR-VLA 1123 Exhaust manifold JAR-VLA 1125 Exhaust heat exchangers

POWERPLANT CONTROLS AND ACCESSORIES

JAR-VLA 1141 General JAR-VLA 1143 Engine controls JAR-VLA 1145 Ignition switches JAR-VLA 1147 Mixture control JAR-VLA 1163 Powerplant accessories JAR-VLA 1165 Engine ignition systems

POWERPLANT FIRE PROTECTION

POWERPLANT FIRE PROTECTION

JAR-VLA 1182 Nacelle areas behind firewalis JAR-VLA 1183 Lines, fittings and components JAR-VLA 1191 Firewalls JAR-VLA 1193 Cowing and nacelle

Page

1-E-5 1-E~5 1-E-5 1-E-5

1-E-6 1-E-6 1-E-6 1-E-6 1-E-6 1-E-6 1-E-6

1-E-6 1-E-6

1-E-7 1-E-8

1-E-8 1-E-8 1-E-8 1-E-8 1-E-8

1-E-6 1-E-6 1-E-6 1-E-6 1-E-6 1-E-6 1-E-6

1-E-9 1-E-9 1-E-9

1-E-9 1-E-9 1-E-10 1-E-10 1-E-10 1-E-10

1-E-10 1-E-10 1-E-11 1-E-11

Paragraph

SUBPART F - EQUIPMENT

GENERAL

JAR-VLA 1301 Function and installation JAR-VLA 1303 Flight and navigation instruments JAR-VLA 1305 Powerplant instruments JAR-VLA 1307 Miscellaneous equipment JAR-VLA 1309 Equipment, systems and installations

INSTRUMENTS: INSTALLATION

INSTRUMENTS: INSTALLATION

JAR-VLA 1321 Arrangement and visibility JAR-VLA 1322 Warning, caution and advisory lights JAR-VLA 1323 Airspeed indicating system JAR-VLA 1325 Static pressure system JAR-VLA 1327 Magnetic direction indicator JAR-VLA 1331 Instruments using 8 power supply JAR-VLA 1337 Powerplant instruments

ELECTRICAL SYSTEMS AND EQUIPMENT

ELECTRICAL SYSTEMS AND EQUIPMENT

JAR-VLA 1351 General JAR-VLA 1353 Storage battery design and installation JAR-VLA 1357 Circuit protective devices JAR-VLA 1361 Master switch arrangement JAR-VLA 1365 Electric cables and equipment JAR-VLA 1367 Switches

LIGHTS

JAR-VLA 1384 Externai lights

SAFETY EQUIPMENT

SAFETY EQUIPMENT

JAR-VLA 1411 General

MISCELLANEOUS EQUIPMENT

JAR-VLA 1431 Electronic equipment JAR-VLA 1436 Hydraulic manually-powered brake systems

Page

1-F-1 1-F-1 1-F-1 1-F-1 1-F-1

1-F-1 1-F-1 1-F-2 1-F- 1-F-2 1-F-2 1-F-2

1-F-3 1-F-3 1-F-4 1-F-4 1-F-4 1-F-4

1-F-5

1-F-5

1-F-5 1-F-5

SUBPART G - OPERATING LIMITATIONS AND INFORMATION

SUBPART G - OPERATING LIMITATIONS AND INFORMATION

JAR-VLA 1501 General JAR-VLA 1505 Airspeed limitations JAR-VLA 1507 Manoeuvring speed JAR-VLA 1511 Flap extended speed JAR-VLA 1519 Weight and centre of gravity JAR-VLA 1521 Powerplant limitations JAR-VLA 1525 Kinds of operation JAR-VLA 1529 Maintenance manual

1-G-1 1-G-1 1-G-1 1-G-1 1-G-1 1-G-1 1-G-2 1-G-2

1-G-1 1-G-1 1-G-1 1-G-1 1-G-1 1-G-1 1-G-2 1-G-2

Paragraph

MARKINGS AND PLACARDS

JAR-VLA 1541 General JAR-VLA 1543 Instrument markings: general JAR-VLA 1545 Airspeed indicator JAR-VLA 1547 Magnetic direction indicator JAR-VLA 1549 Powerplant instruments JAR-VLA 1551 Oil quantity indicator JAR-VLA 1555 Control markings JAR-VLA 1557 Miscellaneous markings and placards JAR-VLA 1559 Operating limitations placards JAR-VLA 1561 Safety equipment

MARKINGS AND PLACARDS

Page

1-G-2 1-G-2 1-G-2 1-G-3 1-G-3 1-G-3 1-G-3 1-G-3 1-G-4 1-G-4

AEROPLANE FLIGHT MANUAL AND APPROVED MANUAL MATERIAL

JAR-VLA 1581 General JAR-VLA 1583 Operating limitations JAR-VLA 1585 Operating data and procedures JAR-VLA 1587 Performance information JAR-VLA 1589 Loading information

AEROPLANE FLIGHT MANUAL AND APPROVED MANUAL MATERIAL

APPENDICES

Appendix A Appendix B Appendix C Appendix F Appendix H

1-G-4 1-G4 1-G-5 1-G-5 1-G-6

1-App A-1 1-App B-1 1-App C-1 1-App F-1 1-App H-1

SECTION 2 ACCEPTABLE MEANS OF COMPLIANCE AND INTERPRETATIONS (ACJ)

26.4.90 C-10

FOREWORD

1 The Civil Aviation Authorities of certain European countries have agreed common comprehensive and detailed airworthiness requirements (referred to as the Joint Aviation Requirements (JAR)) with a view to minimising Type Certification problems on joint ventures. and also to facilitate the export and import of aviation products.

26.4.90 C-10

The JAR are recognised by the Civil Aviation Authorities of participating countries as an acceptable basis for showing compliance with their national airworthiness codes.

FAR Part 23 of the Federal Aviation Administration of the United States of America has been selected to provide the format, and where appropriate, content, of the JAR for Very Light Aeroplanes • (JAR-VLA).

4 Certain of the requirements of this JAR-VLA, in particular those in Subpart F, call for the installation of equipment and in some cases prescribe requirements for the design and per. formance of that equipment. These requirements, in common with the remainder of JAR-VLA are intended to be acceptable to all Participating Authorities as shcwing compliance with their National Code for type certification purposes, but it should be borne in mind that an importing country may require equipment additional to those in this JAR for operational purposes.

5 The performance requirements of Subparts B and G have been developed on the assumption that the resulting scheduled performance data will be used in conjunction with performance operating rules which are complementary to these performance requirements.

6 Future development of the requirements for this JAR will be in accordance with the agreed amendment procedures. Broadiy. these procedures are such that amendment of JAR-VLA car. be proposed by the Civil Aviation Authority of any of the participating countries and by any organ. isation represented on the Joint Steering Assembly.

7 The Civil Aviation Authorities have agreed they should not unilaterally initiate amendment of their nationai codes without having made a proposal for amendmeni of the JAR-VLA in accordance with the agreed procedure.

8 Definitions and abbreviations of terms used in this JAR-VLA are contaired in JAR-1, Definitions and Abbreviations.

9 Amendments to the text in this JAR-VLA are usually issued initially as 'Orange Paper' Amendments. These show an effective date and have the same status and applicability as JAR-VLA from that date. Orange Paper Amendments are incorporated into the printed text by means of a Change'.

10 New, amended and corrected text is enclosed within heavy brackets.

•A Very Light Aeroplane is defined as one of not more than 750 kg Mazimum Certificated Take-off Weight.

F-1 26.4.90

SECTION1 JAR-VLA

SECTION1 JAR-VLA

SECTION 1- REQUIREMENTS

1 GENERAL

This Section 1 contains the Requirements for Very Light Aeroplanes.

2 PRESENTATION

2.1 The requirements of JAR-VLA are presented in two columns on loose pages, each page being identified by the date of issue or the Change number under which it is amended or reissued. 2.2 In general, the JAR paragraphs carry the same number as the corresponding FAR Section. In cases where new JAR material is introduced on a subject atready dealt with in FAR, this is included within the numbering system of the relevant FAR section. In cases where new JAR material is introduced, and there is no corresponding section in FAR, a number is chosen for it which attempts to place the new material in the right context within the FAR numbering system. 2.3Sub-headings are in italic typeface.

2 PRESENTATION

2.4 New, amended and corrected text is enclosed within heavy brackets.

INTENTIONALLY LEFT BLANK

PREAMBLES

This JAR-VLA was issued on 26 April 1990 and became effective on that date.

P-.1 26.4.90

SECIIUN 1 JAR-VLA

(NPA-VLA-1) JAR-VLA 1(a) Add a cross-reference to ACJ VLA 1(a) as follows:-

SECIIUN 1 JAR-VLA

(a) This JAR-VLA prescribes airworthiness standards for issuance of a type certificate, and changes to that type certificate, for an aeroplane with a single engine (spark- or compression-ignition) having not more than two seats, with a Maximum Certificated Take. off Weight of not more than 750 kg and stalling speed in the landing configuration of not more than 45 knots (CAS). The approval [to be for day-VFR only. (See ACJ VLA 1(a).)]

(NPA-VLA-1) JAR-VLA 1(b) Change the existing cross-reference to read ACJ VLA 1(b), as follows:-

(b) Each person who applies for such certificate or change must show compliance with the applicable requirements stated herein. [(See ACJ VLA 1(b).)]

1-A-1

SECTIONT JAR-VLA

SECTIONT JAR-VLA

SUBPART A - GENERAL

JAR-VLA 1 Applicability

(a) This JAR-VLA prescribes airworthiness standards for issuance of a type certificate, and changes to that type certificate, for an aeroplane with a single engine (spark- or compressionignition) having not more than two seats, with a Maximum Certificated Take-off Weight of not more than 750 kg and a stalling speed in the landing configuration of not more than 45 knots (CAS). The approval to be for day-VFR only.

SUBPART A - GENERAL

(b) Each person who applies for such a certificate or change must show compliance with the applicable requirements stated herein. (See ACJ VLA 1.)

JAR-VLA 3 Asroplane categories

This JAR-VLA applies to aeroplanes intended for non-serobatic operation only. Non-aerobatic operation includes—

(a) Any manoeuvre incident to normal Nying:

(b) Stalls (except whip stalls); and

(c) Lazy eights, chandelies, and steep turns, in which the angle of bank is not more than 60°.

1-A-1 26.4.90

SUBPART B - FLIGHT

SUBPART B - FLIGHT

GENERAL

JAR-VLA 21 Proof of compliance

(a) Each requirement of this subpart must be met at cach appropriate combination of weight and centre of gravity within the range of loading conditions for which certification is requested. This must be shown -

(1) By tests upon an aeroplane of the type for which certification is requested, or by caiculations based on, and equal in accuracy to, the results of testing; and

(2) By systematic investigation of each probable combination of weight and centre of gravity, if compliance cannot be reasonably inferred upon combinations investigated.

(b) The foliowing general tolerances are allowed during flight testing. However, greater tolerances may be allowed in particular tests.

ltem Tolerance Weight +5%.-10% Critical items affected by weight +5%, -1% C.G. ±7% total travel.

(c) Substantiation of the data and characteristics to be determined according to this subpart may not require exceptional piloting skill, alertness or exceptionally favourabic conditions. (See ACJ VLA 21(c).)

(d) Consideration must be given to significant variations of performance and in-flight characteristics caused by rain and the accumulation of insects. (See ACJ VLA 21(d).)

JAR-VLA 23 Load distribution limits

Ranges of weight and centres of gravity within which the aeroplane may be safely operated must be established and must include the range of lateral centres of gravity if possible loading conditions can result in significant variation of their positions. (See ACJ VLA 23.)

JAR-VLA 25 Weight limits

(a) Maximum weighi. The maximum weight is the highest weight at which compliance with each applicable requirement of this

JAR-VLA 25 (a) (continued)

JAR-VLA is shown. The maximum weight must be established so that it is —

(1) Not more than

(i) The highest weight selected by the applicant;

(ii) The design maximum weight, which is the highest weight at which compliance with each applicable structural loading condition of this JAR-VLA is shown; or

(iii) The highest weight at which compliance with each applicable flight requirement of this JAR-VLA is shown.

(2) Assuming 2 weight of 86 kg for each occupant of each seat, not less than the weight with

(i) Each seat occupied, full quantity of oil, and at least enough fuel for one bour of operation at rated maximum continuous power; or

(ii) One pilot, full quantity of oil, and fuel to full tank capacity.

(b) Minimum weigh!. The minimum weight (the lowest weight at which compliance with each applicabie requirement of this JAR-VLA is shown) must be established so that it is not more than the sum of -

(1) The empty weight determined under JAR-VLA 29;

(2) The weight of the pilot (assumed as 55 kg); and

(3) The fuel necessary for one half hour of operation at maximum continuous power.

JAR-VLA 29 Empty weight snd corresponding centre of gravity

(a) The empty weight and corresponding centre of gravity must be determined by weighing the aeroplane with —

(1) Fixed ballast;

(2) Unusable fuel determined under JAR-VLA 959; and

(3) Full operating fuids, including —

(i) Oil;

(ii) Hydraulic Ωluid; and

(iii) Other Nluids required for operation of aeroplane systems,

1-B-1

JAR-VLA 29 (continued)

(b) The condition of the aeroplane at the time of determining empty weight must be one that is well defined and can be easily repeated.

JAR-VLA 33 Propeller speed and pitch limits (a) Propeller speed and pitch must be limited to values that ensure safe operation under normal operating conditions. (b) Propellers that cannot be controlied in flight must meet the following requirements: (1) During take-off and initial climb at Vy, the propeller must limit the engine rotational speed at full throttle to a value not greater than the maximum allowabie take-off rotational speed, and (2) During a glide at VNe with throttle closed or the engine inoperative, provided this has no detrimental effect on the engine, the propeller must not permit the engine to achieve a rotational speed greater than 110% of the maximum continous speed. (c) A propeller that can be controlied in flight but does not have constant speed controls must be so designed that - (1) Sub-paragraph (b)(1) is met with the lowest possible pitch selected, and (2) Sub-paragraph (b)(2) is met with the highest possible pitch selected. (d) A controliable pitch propeller with constant speed controls must comply with the following requirements: (1) With the governor in operation, there must be a means to limit the maximum engine rotational speed to the maximum allowable take-off speed, and (2) With the governor inoperative, there must be a means to limit the maximum engine rotational speed to 103% of the maximum allowable take-off speed with the propeller blades at the lowest possible pitch and the aeroplane stationary with no wind at full throttle position.

PERFORMANCE

JAR-VLA 45 General

Unless otherwise prescribed, the performance requirements of this JAR-VLA must be met for still air and a standard atmosphere, at sea level. (See ACJ VLA 45.)

SECTION1

JAR-VLA 49 Stalling speed (a) Vso is the stalling speed, if obtainable, or the minimum steady speed, in knots (CAS), at which the aeroplane is controllable, with the — (1) Power condition set forth in subparagraph (c); (2) Propeller in the take-off position; (3) Landing gear extended;

(4) Wing flaps in the landing position;

(5) Cowl flaps closed;

(6) Centre of gravity in the most unfavourable position within the allowable range; and (7) Maximum weight. (b) Vso may not exced 45 knots (CAS). (c) Vs: is the stalling speed, if obtzinable, or the minimum steady speed, in knots, CAS at which the aeroplane is controllable with

(1) Engine idling, throttle closed; (2) Propeller in the take-off position; (3) Aeroplane in the condition existing in the test in which Vsı is being used; and

(4) Maximum weight. (d) Vse and Vsı must be determined by flight tests, using the procedure specified in JAR-VLA 201.

JAR-VLA 51 Take-off

(a) The distance required to take-ofT from a dry, level, hard surface and climb over a 15 metre obstacle must be determined and must not exceed 500 metres. (b) This must be determined, in a rational and conservative manner, with

(1) The engine operating within approved operating limitations; and (2) The cowl flaps in the normal takeoff position. (c) Upon reaching a height of 15 metres above the take-off surface level, the aeropiane must have reached a speed of not less than 1.3VS1. (d) The starting point for measuring take-off distance must be at rest except for seaplanes and amphibians where it may be a point at which a speed of not more than three knots is reached.

1-B-2

1 SECTION 1

1 SECTION 1

JAR-VLA 65 Climbs

The steady rate of climb must be at least 2m/sec with —

(a) Not more than take-off power;

(b) Landing gear retracted;

(c) Wing flaps in take-off position; and

(d) Cowl flaps in the position used in the cooling tests.

JAR-VLA 75 Landing

The horizontal distance necessary to land and come to a compiete stop (or to a speed of approximately 3 knots for water landings of seapianes and amphibians) from a point 15 m above the landing surface must be determined as follows:

(a) A steady gliding approach with a calibrated airspeed of at least 1.3 Vs: must be maintained down to the 15 m height.

(b) The landing must be made without excessive vertical acceleration or tendency to bounce, nose over, ground loop, porpoise, or water loop. (c) It must be shown that a safe transition to the balked landing conditions of JAR-VLA 77 can be made from the conditions that exist at the 15 m beight.

JAR-VLA 77 Baiked Landing

For balked landings, it must be possibie to maintain

(a) A steady angle of climb at sea level of at least 1:30; or

(b) Level flight at an altitude of 3000 ft and at a speed at which the balked landing transition has been shown to be safe, with

(1) Take-off power;

(2) The landing gear extended; and

(3) The wing flaps in the landing position, except that if the flaps may be safely retracted in two seconds or less, without loss of altitude and without sudden changes of angle of attack or exceptional piloting skill, they may be retracted.

FLIGHT CHARACTERISTICS

FLIGHT CHARACTERISTICS

JAR-VLA 141 General

The aeroplane must meet the requirements of JAR-VLA 143 to 251 at the normally expected operating altitudes.

CONTROLLABILITY AND MANOEUVRABILITY

JAR-VLA 143 General

(a) The aeroplane must be safely controllable and manoeuvrable during - (1) Take-off;

CONTROLLABILITY AND MANOEUVRABILITY

(2) Climb; (3) Level flight; (4) Descent; and (5) Landing (power on and power off). with the wing flaps extended and retracted. (b) It must be possible to make a smooth transition from one flight condition to another (including turns and slips) without danger of exceeding the limit load factor, under any probable operating condition. (c) If marginal conditions exist with regard to required pilot strength, the 'strength of pilots' limits must be shown by quantitative tests. In no case may the limits exceed those prescribed in the following table:

Flaps. appiied to the coatrols Values in daN of force as Pitch Roll Yow Trim tabs, landing gear etc

(a) For temporary appicatioa: Stick- 20 10 Wbeel (applied to rim) 25 20 Rudder pedal 40 Other controts 20 (b) For proloaged appication 2 1.5 10

JAR-VLA 145 Longitudinai Control

(a) It must be possible at any speed below 1.3 Vsi, to pitch the nose downwards so that a speed equal to 1.3 Vsı can be reached promptuly. (1) This must be shown with the aeroplane in all possible configurations, with power on.at maximum continuous power and power idle, and with the aeroplane trimmed at 1.3 Vsi.

JAR-VLA 145 (continued)

(b): It must be possible throughout the appropriate flight envelope to change the configuration (landing gear, wing fap: etc...) without exceeding the pilot forces defined in JAR-VLA 143(c).

(c) It must be possible to raise the nose at VDF at all permitted c.g. positions and engine powers.

(d) It must be possible to maintain steady straight flight and transition into climbs, descents, or turning flight, without exceeding the forces defined in JAR-VLA 143(c).

(e) It must be possible to maintain approximately level flight when flap retraction from any position is made during steady horizontal flight at 1.1 Vs: with simultaneous application of not more than maximum continuous power.

(f) For any trim setting required under JAR-VLA 161(b)(1) it must be possibie to take-off, climb, descend and land the aeroplane in required configurations with no adverse effect and with acceptable control forces.

JAR-VLA 153 Control during landings

It must be possible, while in the landing configuration, to safely complete a landing following an approach to land-

(a) At a speed 5 knots less than the speed used in complying with JAR-VLA 75 and with the aeroplane in trim or as nearly as possible in trim;

(b) With neitber the trimming control being moved throughout the manoeuvre nor the power being increased during the landing flare; and

(c) With power off.

JAR-VLA 155 Elevator control forces in manoeuvres

The elevator control forces during turns or when recovering from manoeuvres must be such that an increase in control forces is needed to cause an increase in load factor. It must be shown by flight measurements that the stick force per 'g'is such that the stick force to achieve the positive limit manoeuvring load factor is not less than 7 daN in the clean configuration.

JAR-VLA 157 Rate of roll

(a) Take-ofs. It must be possible, using a favourable combination of controls, to roll the aeroplane from a steady 30 degree banked turn through an angle of 60 degrees, so as to reverse the direction of the turn within 5 seconds from initiation of roll with

(1) Flaps in the take-off position;

(2) Landing gear retracted;

(3) Maximum take-off power; and

(4) The aeroplane trimmed at 1.2 Vsi, or as neariy as possible in trim for straight flight.

(b) Approach. It must be possible, using favourable combination of controls, to roll the aeroplane from a steady 30 degree banked turn through an angle of 60 degrees, so as to reverse the direction of the turn within 4 seconds from initiation of roll with

(1) Flaps extended;

(2) Landing gear extended;

(3) Engine operating at idle power and engine operating at the power for level flight; and

(4) The zeroplane trimmed at 1.3 Vsi.

TRIM

JAR-VLA 161 Trim

(a) Lateral and directional trim. In level flight at 0.9 VH or Vc (whichever is lower) the seroplane must remain in trimmed condition around roll and yaw axis with respective controls free. (VH is maximum speed in level flight with maximum continuous power.) .

(b) Longitudinal trim

(1) The aeroplane must maintain longitudinal trim in level flight at any speed from 1-4 Vsi to 0-9 VH or Vc (whichever is lower).

(2) The seroplane must maintain longitudinal trim during

(i) A climb with maximum continuous power at a speed Vy with landing gear and wing flaps retracted;

(ii) A descent with idle power at a speed of 1.3 Vs: with landing gear extended, and wing flaps in the landing position.

1-B4

STABILITY

JAR-VLA 171 General

The aeroplane must be longitudinally, directionally, and laterally stable under JAR-VLA 173 to 181. In addition, the aeroplane must show suitable stability and control 'feel' (static stability) in any condition normally encountered in service, if flight tests show it is necesasry for safe operation.

JAR-VLA 173 Static longitudinal stability

Under the conditions specified in JAR-VLA 175 and with the aeroplane trimmed as indicated, the characteristics of the elevator control forces and the friction within the control system must be as follows:

(a) A pull must be required to obtain and maintain speeds below the specified trim speed and a push required to obiain and maintain speeds above the specified trim speed. This must be shown at any speed that can be obtained, except that speeds requiring a control force in excess of 18 daN, or speeds above the maximum allowable speed or below the minimum speed for steady unstalled flight, need not be considered.

(b) The airspeed must return to within ±10% of the original trim speed when the control force is slowly released at any speed within the speed range specified in sub-paragraph (a) of this paragraph. (c) The stick force must vary with speed so that any substantial speed change results in a stick force clearly perceptible to the pilot. (See ACJ VLA 173 and ACJ VLA 175.)

JAR-VLA 175 Demonstration of static longitudina! stability

Static longitudinal stability must be shown as follows:

(a) Climb. The stick force curve must have a stable slope, at speeds between 15% above and below the trim speed, with

(1) Flaps in the climb position;

(2) Landing gear retracted;

(3) At least 75% of maximum continuous power; and

(4) The aeroplane trimmed for VY, except that the speed need not be iess than 1-4 Vs: or the speed used for showing compliance to the powerplant cooling requirement of JAR-VLA 1041.

JAR-VLA 175 (continued)

(b) Cruise. The stick force curve must have a stable slope with a range of 15% of the trim speed, but not exceeding the range from 1.3 Vs. to VNE, with —

(1) Flaps retracted;

(2) Landing gear retracted; (3) 75% of maximum continuous power; and

(4) The aeroplane trimmed for level flight.

(c) Approach and landing. The stick force curve must have a stable slope at speeds throughout the range of speeds between 1.1 Vs: and VFE or 1.8 Vs: if there is no VFE, with —

(1) Wing flaps in the landing position;

(2) Landing gear extended;

(3) Power idle; and

(4) The aeroplane trimmed at 1.3 Vsi. (See ACJ VLA 173 and ACI VLA 175.)

JAR-VLA 177 Static directional and lateral stability

(a) Three-control aeropianes. The stability requirements for three-control aeroplanes are as follows:

(1) The static directional stability, as shown by the tendency to recover from a skid with the rudder free, must be positive for any landing gear and flap position appropriate to the take-off, climb, cruise, and approach configurations. This must be shown with power up to maximum continuous power, and at speeds from 1.2 Vsi up to maximum allowable speed for the condition being investigated. The angle of skid for these tests must be approprizte to the type of aeroplane. At larger angles of skid up to that at which full rudder is used or a control force limit in JAR-VLA 143 is reached, whichever occurs first, and at speeds from 1.2 Vs: to Va, the rudder pedal force must not reverse.

(2) The static lateral stability, as shown by the tendency to raise the low wing in a slip. must be positive for any landing gear and flap positions. This must be shown with power up to 75% of maximum continuous power at speeds above 1.2 Vsi, up to the maximum allowable speed for the configuration being investigated. The static lateral stability may not be negative at 1-2 Vsi. The angle of slip for these tests must be appropriate to the type of aeroplane, but in no case may the slip angle be less than that obtainabie with 10° of bank.

1-B-5

JAR-VLA 177 (a) (continued)

(3) In straight, steady slips at 1.2 Vs, for any landing gear and flap positions, and for power conditions up to 50% of maximum continuous power, the aileron and rudder control movements and forces must increase steadily (but not necessarily in constant proportion) as the angle of slip is increased up to the maximum appropriate to the type of aeropiane. At larger slip angies up to the angle at which full rudder or aileron control is used or a control force limit contained in JAR-VLA 143 is obtained, the rudder pedal force may not reverse. Enough bank must accompany slipping to hold a constant heading. Rapid entry into, or recovery from, a maximum slip may not resuli in uncontrollable flight characteristics. (b) Two-control (or simplified control) aeroplanes. The stability requirements for twocontrol aeroplanes are as follows: (1) The directional stability of the aeroplane must be shown by showing that, in each configuration, it can be rapidly rolled from a 45° bank in one direction to a 45° bank in the opposite direction without showing dangerous skid characteristics.

(2) The Lateral stability of the aeroplane must be shown by showing that it will not assume a dangerous attitude or speed when the controls are abandoned for two minutes. This must be done in moderately smooth air with the aeroplane trimmed for straight level flight at 0.9 VH or Vc, whichever is lower, with flaps and landing gear retracted, and with a rearward centre of gravity.

JAR-VLA 181 Dynamic stability

(a) Any short period oscillation not including combined lateral-directional oscillations occurring between the stalling speed and the maximum allowable speed appropriate to the configuration of the aeroplane must be 'heavily damped with the primary controls - (1) Free; and

(2) In a fixed position. (b) Any combined lateral-directional oscillations (Dutch roll') occuring between the stalling speed and the maximum allowable speed appropriate to the configuration of the seroplane must be damped to %o amplitude in 7 cycles with the primary controls (1) Free; and (2) In a fixed position.

STALLS

Continue reading ↓ 120 of 416 passages shown